Message-ID: <20150925114029.GH27119@pali>
Date:	Fri, 25 Sep 2015 13:40:29 +0200
From:	Pali Rohár <pali.rohar@...il.com>
To:	Robert Hancock <hancockrwd@...il.com>
Cc:	Jeff Garzik <jeff@...zik.org>, Robert Hancock <hancockr@...w.ca>,
	Tejun Heo <tj@...nel.org>,
	"linux-ide@...r.kernel.org" <linux-ide@...r.kernel.org>,
	linux-kernel <linux-kernel@...r.kernel.org>
Subject: Re: linux: sata_nv: adma support

On Tuesday 04 August 2015 20:06:57 Pali Rohár wrote:
> On Monday 03 August 2015 05:02:15 Robert Hancock wrote:
> > On Sun, Aug 2, 2015 at 3:08 AM, Pali Rohár <pali.rohar@...il.com>
> > wrote:
> > > On Sunday 02 August 2015 03:45:32 Robert Hancock wrote:
> > >> On Sat, Aug 1, 2015 at 2:09 PM, Pali Rohár <pali.rohar@...il.com>
> > >> 
> > >> wrote:
> > >> > On Thursday 25 December 2014 07:22:13 Robert Hancock wrote:
> > >> >> On Tue, Dec 23, 2014 at 1:51 PM, Pali Rohár
> > >> >> <pali.rohar@...il.com>
> > >> >> 
> > >> >> wrote:
> > >> >> > Hello,
> > >> >> > 
> > >> >> > I have nvidia nforce4 motherboard with nvidia sata
> > >> >> > controller:
> > >> >> > 
> > >> >> > 00:07.0 IDE interface [0101]: NVIDIA Corporation CK804 Serial
> > >> >> > ATA Controller [10de:0054] (rev f3)
> > >> >> > 00:08.0 IDE interface [0101]: NVIDIA Corporation CK804 Serial
> > >> >> > ATA Controller [10de:0055] (rev f3)
> > >> >> > 
> > >> >> > I manually enabled adma mode (which is disabled by default)
> > >> >> > by adding sata_nv.adma=1 to grub cmdline. In git history I
> > >> >> > found that enabling adma mode includes NCQ support and
> > >> >> > reduced CPU overhead. It looks like adma mode is working,
> > >> >> > but at every boot I see one same error message in dmesg:
> > >> >> > 
> > >> >> > [   16.823514] ata1.00: exception Emask 0x1 SAct 0x0 SErr 0x0
> > >> >> > action 0x0
> > >> >> > [   16.823520] ata1.00: CPB resp_flags 0x11: , CMD error
> > >> >> > [   16.823524] ata1.00: failed command: SET FEATURES
> > >> >> > [   16.823530] ata1.00: cmd
> > >> >> > ef/05:fe:00:00:00/00:00:00:00:00/40 tag 16
> > >> >> > [   16.823530]          res
> > >> >> > 51/04:fe:00:00:00/00:00:00:00:00/40 Emask 0x1 (device error)
> > >> >> > [   16.823533] ata1.00: status: { DRDY ERR }
> > >> >> > [   16.823535] ata1.00: error: { ABRT }
> > >> >> > 
> > >> >> > When adma is disabled then this error message is not
> > >> >> > generated.
> > >> >> 
> > >> >> It looks like something is trying to issue a command to disable
> > >> >> APM power management on the drive, and the command fails
> > >> >> (likely because it doesn't support that command). I'm not sure
> > >> >> where that would be coming from - I'm pretty sure the kernel
> > >> >> doesn't issue that command itself. Something that's part of
> > >> >> your distro perhaps?
> > >> >> 
> > >> >> I don't know why it would only be failing in ADMA mode either,
> > >> >> though depending on where the command is coming from, maybe
> > >> >> it's not being issued otherwise for some reason?
> > >> >> 
> > >> >> > What does that error message means? It is critical? What is
> > >> >> > that command SET FEATURES doing? Are there any problems with
> > >> >> > adma mode on nforce4 motherboards? Because I did not see any
> > >> >> > problems (except that one error message).
> > >> >> > 
> > >> >> > --
> > >> >> > Pali Rohár
> > >> >> > pali.rohar@...il.com
> > >> > 
> > >> > Hello,
> > >> > 
> > >> > now after long time I did more investigation and that error is
> > >> > reported for every connected HDD. I identified that it comes
> > >> > from udev script
> > >> > 
> > >> >  /lib/udev/rules.d/85-hdparm.rules
> > >> > 
> > >> > which just call script /lib/udev/hdparm for every one connected
> > >> > HDD.
> > >> > 
> > >> > Script /lib/udev/hdparm just call:
> > >> >  /sbin/hdparm -B254 $DRIVE
> > >> > 
> > >> > And that -B254 cause above error message in dmesg log. Output
> > >> > from
> > >> > 
> > >> > hdparm is:
> > >> >  /dev/sda:
> > >> >   setting Advanced Power Management level to 0xfe (254)
> > >> >   APM_level      = not supported
> > >> > 
> > >> > Any idea why in ADMA mode it cause above error (APM unsupported)
> > >> > and in non ADMA mode it is working fine? Maybe APM ATA commands
> > >> > should not be sent via ADMA?
> > >> > 
> > >> > Here is another output:
> > >> >  $ sudo hdparm -I /dev/sda | grep -i power
> > >> >  
> > >> >             *    Power Management feature set
> > >> >             
> > >> >                  Power-Up In Standby feature set
> > >> >             
> > >> >             *    SET_FEATURES required to spinup after power up
> > >> >             *    Host-initiated interface power management
> > >> 
> > >> The "set features" command is a non-data command so based on our
> > >> current knowledge, it should work in ADMA mode. However, these
> > >> NVIDIA SATAs are black boxes, and rather buggy ones at that, so
> > >> it's possible there's an unknown issue there.
> > > 
> > > Maybe I should note that hdparm -I did not generated any error
> > > message. I post is here because it show "Power Management feature
> > > set" is supported by HDD. This indicate that HDD supports -B (APM)
> > > command, right?
> > 
> > As far as I know, yes.
> > 
> > >> The easiest way to test that would be to take out the condition
> > >> check for qc->tf.protocol == ATA_PROT_NODATA in
> > >> nv_adma_use_reg_mode in drivers/ata/sata_nv.c. That would force
> > >> it to disable ADMA for all non-data commands.
> > > 
> > > Ok, as now I have just SSH access to that machine, I will do kernel
> > > patching later (when I have physical access to it).
> > > 
> > >> I really don't know why Ubuntu is disabling APM on all drives on
> > >> bootup however. Especially for laptops, that seems like a silly
> > >> thing to do explicitly. Sounds like one of the silly things
> > >> Ubuntu is known to do without consulting people.
> > > 
> > > Looks like this comes from upstream udev/systemd project :-(
> > > Anyway, for laptops on battery ubuntu has another set of scripts
> > > which turn on APM (based on connected/disconnected AC adapter).
> > 
> > There's no such scripts in Fedora, so either they removed it, or it's
> > something that either Debian or Ubuntu has added in.
> > 
> > > That udev script which turn off APM is called when any disk is
> > > attached to system (so at boot time it is called for every one
> > > disk).
> > > 
> > > Now I just masked that udev script and it is no longer called...
> > > 
> > > Anyway if I call hdparm -B /dev/sda I get output:
> > > 
> > > APM_level      = not supported
> > > 
> > > And important is that there is no error message in dmesg. I get it
> > > only if I call hdparm -B with parameter (set option). But APM
> > > should be supported, right?
> > 
> > Does the get command work without ADMA enabled?
> 
> I requested to boot that machine with turned off ADMA. I verified it is 
> turned off as I found sata_nv.adma=0 in /proc/cmdline and file 
> /sys/module/sata_nv/parameters/adma contains big N.
> 
> I called hdparm:
> 
> $ sudo hdparm -B254 /dev/sda
> 
> /dev/sda:
>  setting Advanced Power Management level to 0xfe (254)
>  HDIO_DRIVE_CMD failed: Input/output error
>  APM_level      = not supported
> 
> It failed, but I do not see any error message in dmesg. There is nothing 
> new in dmesg.
> 
> So looks like I'm not able to set APM... But why in ADMA mode it 
> generates some error and in non ADMA mode no error? Strange!
> 

Hi Robert! Any idea why in ADMA mode I get that error and in non ADMA
not? Where could be problem?

-- 
Pali Rohár
pali.rohar@...il.com
--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@...r.kernel.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html
Please read the FAQ at  http://www.tux.org/lkml/

Powered by blists - more mailing lists