| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-Id: <1443717488-16533-2-git-send-email-jon@ringle.org>
Date: Thu, 1 Oct 2015 12:38:08 -0400
From: jon@...gle.org
To: broonie@...nel.org, gregkh@...uxfoundation.org,
linux-kernel@...r.kernel.org, netdev@...r.kernel.org
Cc: Jon Ringle <jringle@...dpoint.com>
Subject: [PATCH net-next v3 2/2] net: Microchip encx24j600 driver
From: Jon Ringle <jringle@...dpoint.com>
This ethernet driver supports the Micorchip enc424j600/626j600 Ethernet
controller over a SPI bus interface. This driver makes use of the regmap API to
optimize access to registers by caching registers where possible.
Datasheet:
http://ww1.microchip.com/downloads/en/DeviceDoc/39935b.pdf
Signed-off-by: Jon Ringle <jringle@...dpoint.com>
---
Fixed several issues reported by kbuild bots and simplified the implementation
of regmap_encx24j600_reg_update_bits() based on changes to _regmap_update_bits
Jon
drivers/net/ethernet/microchip/Kconfig | 9 +
drivers/net/ethernet/microchip/Makefile | 1 +
drivers/net/ethernet/microchip/encx24j600-regmap.c | 513 +++++++++
drivers/net/ethernet/microchip/encx24j600.c | 1124 ++++++++++++++++++++
drivers/net/ethernet/microchip/encx24j600_hw.h | 437 ++++++++
5 files changed, 2084 insertions(+)
create mode 100644 drivers/net/ethernet/microchip/encx24j600-regmap.c
create mode 100644 drivers/net/ethernet/microchip/encx24j600.c
create mode 100644 drivers/net/ethernet/microchip/encx24j600_hw.h
diff --git a/drivers/net/ethernet/microchip/Kconfig b/drivers/net/ethernet/microchip/Kconfig
index afaf0c0..b45b28a 100644
--- a/drivers/net/ethernet/microchip/Kconfig
+++ b/drivers/net/ethernet/microchip/Kconfig
@@ -35,4 +35,13 @@ config ENC28J60_WRITEVERIFY
Enable the verify after the buffer write useful for debugging purpose.
If unsure, say N.
+config ENCX24J600
+ tristate "ENCX24J600 support"
+ depends on SPI
+ ---help---
+ Support for the Microchip ENC424J600 ethernet chip.
+
+ To compile this driver as a module, choose M here. The module will be
+ called enc424j600.
+
endif # NET_VENDOR_MICROCHIP
diff --git a/drivers/net/ethernet/microchip/Makefile b/drivers/net/ethernet/microchip/Makefile
index 573d429..ff78f62 100644
--- a/drivers/net/ethernet/microchip/Makefile
+++ b/drivers/net/ethernet/microchip/Makefile
@@ -3,3 +3,4 @@
#
obj-$(CONFIG_ENC28J60) += enc28j60.o
+obj-$(CONFIG_ENCX24J600) += encx24j600.o encx24j600-regmap.o
diff --git a/drivers/net/ethernet/microchip/encx24j600-regmap.c b/drivers/net/ethernet/microchip/encx24j600-regmap.c
new file mode 100644
index 0000000..f3bb905
--- /dev/null
+++ b/drivers/net/ethernet/microchip/encx24j600-regmap.c
@@ -0,0 +1,513 @@
+/**
+ * Register map access API - ENCX24J600 support
+ *
+ * Copyright 2015 Gridpoint
+ *
+ * Author: Jon Ringle <jringle@...dpoint.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include <linux/delay.h>
+#include <linux/errno.h>
+#include <linux/init.h>
+#include <linux/module.h>
+#include <linux/netdevice.h>
+#include <linux/regmap.h>
+#include <linux/spi/spi.h>
+
+#include "encx24j600_hw.h"
+
+static inline bool is_bits_set(int value, int mask)
+{
+ return (value & mask) == mask;
+}
+
+static int encx24j600_switch_bank(struct encx24j600_context *ctx,
+ int bank)
+{
+ int ret = 0;
+
+ int bank_opcode = BANK_SELECT(bank);
+ ret = spi_write(ctx->spi, &bank_opcode, 1);
+ if (ret == 0)
+ ctx->bank = bank;
+
+ return ret;
+}
+
+static int encx24j600_cmdn(struct encx24j600_context *ctx, u8 opcode,
+ const void *buf, size_t len)
+{
+ struct spi_message m;
+ struct spi_transfer t[2] = { { .tx_buf = &opcode, .len = 1, },
+ { .tx_buf = buf, .len = len }, };
+ spi_message_init(&m);
+ spi_message_add_tail(&t[0], &m);
+ spi_message_add_tail(&t[1], &m);
+
+ return spi_sync(ctx->spi, &m);
+}
+
+static void regmap_lock_mutex(void *context)
+{
+ struct encx24j600_context *ctx = context;
+ mutex_lock(&ctx->mutex);
+}
+
+static void regmap_unlock_mutex(void *context)
+{
+ struct encx24j600_context *ctx = context;
+ mutex_unlock(&ctx->mutex);
+}
+
+static int regmap_encx24j600_sfr_read(void *context, u8 reg, u8 *val,
+ size_t len)
+{
+ struct encx24j600_context *ctx = context;
+ u8 banked_reg = reg & ADDR_MASK;
+ u8 bank = ((reg & BANK_MASK) >> BANK_SHIFT);
+ u8 cmd = RCRU;
+ int ret = 0;
+ int i = 0;
+ u8 tx_buf[2];
+
+ if (reg < 0x80) {
+ cmd = RCRCODE | banked_reg;
+ if ((banked_reg < 0x16) && (ctx->bank != bank))
+ ret = encx24j600_switch_bank(ctx, bank);
+ if (unlikely(ret))
+ return ret;
+ } else {
+ /* Translate registers that are more effecient using
+ * 3-byte SPI commands
+ */
+ switch (reg) {
+ case EGPRDPT:
+ cmd = RGPRDPT; break;
+ case EGPWRPT:
+ cmd = RGPWRPT; break;
+ case ERXRDPT:
+ cmd = RRXRDPT; break;
+ case ERXWRPT:
+ cmd = RRXWRPT; break;
+ case EUDARDPT:
+ cmd = RUDARDPT; break;
+ case EUDAWRPT:
+ cmd = RUDAWRPT; break;
+ case EGPDATA:
+ case ERXDATA:
+ case EUDADATA:
+ default:
+ return -EINVAL;
+ }
+ }
+
+ tx_buf[i++] = cmd;
+ if (cmd == RCRU)
+ tx_buf[i++] = reg;
+
+ ret = spi_write_then_read(ctx->spi, tx_buf, i, val, len);
+
+ return ret;
+}
+
+static int regmap_encx24j600_sfr_update(struct encx24j600_context *ctx,
+ u8 reg, u8 *val, size_t len,
+ u8 unbanked_cmd, u8 banked_code)
+{
+ u8 banked_reg = reg & ADDR_MASK;
+ u8 bank = ((reg & BANK_MASK) >> BANK_SHIFT);
+ u8 cmd = unbanked_cmd;
+ struct spi_message m;
+ struct spi_transfer t[3] = { { .tx_buf = &cmd, .len = sizeof(cmd), },
+ { .tx_buf = ®, .len = sizeof(reg), },
+ { .tx_buf = val, .len = len }, };
+
+ if (reg < 0x80) {
+ int ret = 0;
+ cmd = banked_code | banked_reg;
+ if ((banked_reg < 0x16) && (ctx->bank != bank))
+ ret = encx24j600_switch_bank(ctx, bank);
+ if (unlikely(ret))
+ return ret;
+ } else {
+ /* Translate registers that are more effecient using
+ * 3-byte SPI commands
+ */
+ switch (reg) {
+ case EGPRDPT:
+ cmd = WGPRDPT; break;
+ case EGPWRPT:
+ cmd = WGPWRPT; break;
+ case ERXRDPT:
+ cmd = WRXRDPT; break;
+ case ERXWRPT:
+ cmd = WRXWRPT; break;
+ case EUDARDPT:
+ cmd = WUDARDPT; break;
+ case EUDAWRPT:
+ cmd = WUDAWRPT; break;
+ case EGPDATA:
+ case ERXDATA:
+ case EUDADATA:
+ default:
+ return -EINVAL;
+ }
+ }
+
+ spi_message_init(&m);
+ spi_message_add_tail(&t[0], &m);
+
+ if (cmd == unbanked_cmd) {
+ t[1].tx_buf = ®
+ spi_message_add_tail(&t[1], &m);
+ }
+
+ spi_message_add_tail(&t[2], &m);
+ return spi_sync(ctx->spi, &m);
+}
+
+static int regmap_encx24j600_sfr_write(void *context, u8 reg, u8 *val,
+ size_t len)
+{
+ struct encx24j600_context *ctx = context;
+ return regmap_encx24j600_sfr_update(ctx, reg, val, len, WCRU, WCRCODE);
+}
+
+static int regmap_encx24j600_sfr_set_bits(struct encx24j600_context *ctx,
+ u8 reg, u8 val)
+{
+ return regmap_encx24j600_sfr_update(ctx, reg, &val, 1, BFSU, BFSCODE);
+}
+
+static int regmap_encx24j600_sfr_clr_bits(struct encx24j600_context *ctx,
+ u8 reg, u8 val)
+{
+ return regmap_encx24j600_sfr_update(ctx, reg, &val, 1, BFCU, BFCCODE);
+}
+
+static int regmap_encx24j600_reg_update_bits(void *context, unsigned int reg,
+ unsigned int mask,
+ unsigned int val)
+{
+ struct encx24j600_context *ctx = context;
+
+ int ret = 0;
+ unsigned int set_mask = mask & val;
+ unsigned int clr_mask = mask & ~val;
+
+ if ((reg >= 0x40 && reg < 0x6c) || reg >= 0x80)
+ return -EINVAL;
+
+ if (set_mask & 0xff)
+ ret = regmap_encx24j600_sfr_set_bits(ctx, reg, set_mask);
+
+ set_mask = (set_mask & 0xff00) >> 8;
+
+ if ((set_mask & 0xff) && (ret == 0))
+ ret = regmap_encx24j600_sfr_set_bits(ctx, reg + 1, set_mask);
+
+ if ((clr_mask & 0xff) && (ret == 0))
+ ret = regmap_encx24j600_sfr_clr_bits(ctx, reg, clr_mask);
+
+ clr_mask = (clr_mask & 0xff00) >> 8;
+
+ if ((clr_mask & 0xff) && (ret == 0))
+ ret = regmap_encx24j600_sfr_clr_bits(ctx, reg + 1, clr_mask);
+
+ return ret;
+}
+
+int regmap_encx24j600_spi_write(void *context, u8 reg, const u8 *data,
+ size_t count)
+{
+ struct encx24j600_context *ctx = context;
+
+ if (reg < 0xc0)
+ return encx24j600_cmdn(ctx, reg, data, count);
+ else
+ /* SPI 1-byte command. Ignore data */
+ return spi_write(ctx->spi, ®, 1);
+}
+EXPORT_SYMBOL_GPL(regmap_encx24j600_spi_write);
+
+int regmap_encx24j600_spi_read(void *context, u8 reg, u8 *data, size_t count)
+{
+ struct encx24j600_context *ctx = context;
+
+ if (reg == RBSEL && count > 1)
+ count = 1;
+
+ return spi_write_then_read(ctx->spi, ®, sizeof(reg), data, count);
+}
+EXPORT_SYMBOL_GPL(regmap_encx24j600_spi_read);
+
+static int regmap_encx24j600_write(void *context, const void *data,
+ size_t len)
+{
+ u8 *dout = (u8 *)data;
+ u8 reg = dout[0];
+ ++dout;
+ --len;
+
+ if (reg > 0xa0)
+ return regmap_encx24j600_spi_write(context, reg, dout, len);
+
+ if (len > 2)
+ return -EINVAL;
+
+ return regmap_encx24j600_sfr_write(context, reg, dout, len);
+}
+
+static int regmap_encx24j600_read(void *context,
+ const void *reg_buf, size_t reg_size,
+ void *val, size_t val_size)
+{
+ u8 reg = *(const u8 *)reg_buf;
+
+ if (reg_size != 1) {
+ pr_err("%s: reg=%02x reg_size=%zu\n", __func__, reg, reg_size);
+ return -EINVAL;
+ }
+
+ if (reg > 0xa0)
+ return regmap_encx24j600_spi_read(context, reg, val, val_size);
+
+ if (val_size > 2) {
+ pr_err("%s: reg=%02x val_size=%zu\n", __func__, reg, val_size);
+ return -EINVAL;
+ }
+
+ return regmap_encx24j600_sfr_read(context, reg, val, val_size);
+}
+
+static bool encx24j600_regmap_readable(struct device *dev, unsigned int reg)
+{
+ if ((reg < 0x36) ||
+ ((reg >= 0x40) && (reg < 0x4c)) ||
+ ((reg >= 0x52) && (reg < 0x56)) ||
+ ((reg >= 0x60) && (reg < 0x66)) ||
+ ((reg >= 0x68) && (reg < 0x80)) ||
+ ((reg >= 0x86) && (reg < 0x92)) ||
+ (reg == 0xc8))
+ return true;
+ else
+ return false;
+}
+
+static bool encx24j600_regmap_writeable(struct device *dev, unsigned int reg)
+{
+ if ((reg < 0x12) ||
+ ((reg >= 0x14) && (reg < 0x1a)) ||
+ ((reg >= 0x1c) && (reg < 0x36)) ||
+ ((reg >= 0x40) && (reg < 0x4c)) ||
+ ((reg >= 0x52) && (reg < 0x56)) ||
+ ((reg >= 0x60) && (reg < 0x68)) ||
+ ((reg >= 0x6c) && (reg < 0x80)) ||
+ ((reg >= 0x86) && (reg < 0x92)) ||
+ ((reg >= 0xc0) && (reg < 0xc8)) ||
+ ((reg >= 0xca) && (reg < 0xf0)))
+ return true;
+ else
+ return false;
+}
+
+static bool encx24j600_regmap_volatile(struct device *dev, unsigned int reg)
+{
+ switch (reg) {
+ case ERXHEAD:
+ case EDMACS:
+ case ETXSTAT:
+ case ETXWIRE:
+ case ECON1: /* Can be modified via single byte cmds */
+ case ECON2: /* Can be modified via single byte cmds */
+ case ESTAT:
+ case EIR: /* Can be modified via single byte cmds */
+ case MIRD:
+ case MISTAT:
+ return true;
+ default:
+ break;
+ }
+
+ return false;
+}
+
+static bool encx24j600_regmap_precious(struct device *dev, unsigned int reg)
+{
+ /* single byte cmds are precious */
+ if (((reg >= 0xc0) && (reg < 0xc8)) ||
+ ((reg >= 0xca) && (reg < 0xf0)))
+ return true;
+ else
+ return false;
+}
+
+static int regmap_encx24j600_phy_reg_read(void *context, unsigned int reg,
+ unsigned int *val)
+{
+ struct encx24j600_context *ctx = context;
+ int ret;
+ unsigned int mistat;
+
+ reg = MIREGADR_VAL | (reg & PHREG_MASK);
+ ret = regmap_write(ctx->regmap, MIREGADR, reg);
+ if (unlikely(ret))
+ goto err_out;
+
+ ret = regmap_write(ctx->regmap, MICMD, MIIRD);
+ if (unlikely(ret))
+ goto err_out;
+
+ usleep_range(26, 100);
+ while ((ret = regmap_read(ctx->regmap, MISTAT, &mistat) != 0) &&
+ (mistat & BUSY))
+ cpu_relax();
+
+ if (unlikely(ret))
+ goto err_out;
+
+ ret = regmap_write(ctx->regmap, MICMD, 0);
+ if (unlikely(ret))
+ goto err_out;
+
+ ret = regmap_read(ctx->regmap, MIRD, val);
+
+err_out:
+ if (ret)
+ pr_err("%s: error %d reading reg %02x\n", __func__, ret,
+ reg & PHREG_MASK);
+
+ return ret;
+}
+
+static int regmap_encx24j600_phy_reg_write(void *context, unsigned int reg,
+ unsigned int val)
+{
+ struct encx24j600_context *ctx = context;
+ int ret;
+ unsigned int mistat;
+
+ reg = MIREGADR_VAL | (reg & PHREG_MASK);
+ ret = regmap_write(ctx->regmap, MIREGADR, reg);
+ if (unlikely(ret))
+ goto err_out;
+
+ ret = regmap_write(ctx->regmap, MIWR, val);
+ if (unlikely(ret))
+ goto err_out;
+
+ usleep_range(26, 100);
+ while ((ret = regmap_read(ctx->regmap, MISTAT, &mistat) != 0) &&
+ (mistat & BUSY))
+ cpu_relax();
+
+err_out:
+ if (ret)
+ pr_err("%s: error %d writing reg %02x=%04x\n", __func__, ret,
+ reg & PHREG_MASK, val);
+
+ return ret;
+}
+
+static bool encx24j600_phymap_readable(struct device *dev, unsigned int reg)
+{
+ switch (reg) {
+ case PHCON1:
+ case PHSTAT1:
+ case PHANA:
+ case PHANLPA:
+ case PHANE:
+ case PHCON2:
+ case PHSTAT2:
+ case PHSTAT3:
+ return true;
+ default:
+ return false;
+ }
+}
+
+static bool encx24j600_phymap_writeable(struct device *dev, unsigned int reg)
+{
+ switch (reg) {
+ case PHCON1:
+ case PHCON2:
+ case PHANA:
+ return true;
+ case PHSTAT1:
+ case PHSTAT2:
+ case PHSTAT3:
+ case PHANLPA:
+ case PHANE:
+ default:
+ return false;
+ }
+}
+
+static bool encx24j600_phymap_volatile(struct device *dev, unsigned int reg)
+{
+ switch (reg) {
+ case PHSTAT1:
+ case PHSTAT2:
+ case PHSTAT3:
+ case PHANLPA:
+ case PHANE:
+ case PHCON2:
+ return true;
+ default:
+ return false;
+ }
+}
+
+static struct regmap_config regcfg = {
+ .name = "reg",
+ .reg_bits = 8,
+ .val_bits = 16,
+ .max_register = 0xee,
+ .reg_stride = 2,
+ .cache_type = REGCACHE_RBTREE,
+ .val_format_endian = REGMAP_ENDIAN_LITTLE,
+ .readable_reg = encx24j600_regmap_readable,
+ .writeable_reg = encx24j600_regmap_writeable,
+ .volatile_reg = encx24j600_regmap_volatile,
+ .precious_reg = encx24j600_regmap_precious,
+ .lock = regmap_lock_mutex,
+ .unlock = regmap_unlock_mutex,
+};
+
+static struct regmap_bus regmap_encx24j600 = {
+ .write = regmap_encx24j600_write,
+ .read = regmap_encx24j600_read,
+ .reg_update_bits = regmap_encx24j600_reg_update_bits,
+};
+
+static struct regmap_config phycfg = {
+ .name = "phy",
+ .reg_bits = 8,
+ .val_bits = 16,
+ .max_register = 0x1f,
+ .cache_type = REGCACHE_RBTREE,
+ .val_format_endian = REGMAP_ENDIAN_LITTLE,
+ .readable_reg = encx24j600_phymap_readable,
+ .writeable_reg = encx24j600_phymap_writeable,
+ .volatile_reg = encx24j600_phymap_volatile,
+};
+static struct regmap_bus phymap_encx24j600 = {
+ .reg_write = regmap_encx24j600_phy_reg_write,
+ .reg_read = regmap_encx24j600_phy_reg_read,
+};
+
+void devm_regmap_init_encx24j600(struct device *dev,
+ struct encx24j600_context *ctx)
+{
+ mutex_init(&ctx->mutex);
+ regcfg.lock_arg = ctx;
+ ctx->regmap = devm_regmap_init(dev, ®map_encx24j600, ctx, ®cfg);
+ ctx->phymap = devm_regmap_init(dev, &phymap_encx24j600, ctx, &phycfg);
+}
+EXPORT_SYMBOL_GPL(devm_regmap_init_encx24j600);
+
+MODULE_LICENSE("GPL");
diff --git a/drivers/net/ethernet/microchip/encx24j600.c b/drivers/net/ethernet/microchip/encx24j600.c
new file mode 100644
index 0000000..afc008a
--- /dev/null
+++ b/drivers/net/ethernet/microchip/encx24j600.c
@@ -0,0 +1,1124 @@
+/**
+ * Microchip ENCX24J600 ethernet driver
+ *
+ * Copyright (C) 2015 Gridpoint
+ * Author: Jon Ringle <jringle@...dpoint.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ */
+
+#include <linux/device.h>
+#include <linux/errno.h>
+#include <linux/etherdevice.h>
+#include <linux/ethtool.h>
+#include <linux/interrupt.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/netdevice.h>
+#include <linux/regmap.h>
+#include <linux/skbuff.h>
+#include <linux/spi/spi.h>
+
+#include "encx24j600_hw.h"
+
+#define DRV_NAME "encx24j600"
+#define DRV_VERSION "1.0"
+
+#define DEFAULT_MSG_ENABLE (NETIF_MSG_DRV | NETIF_MSG_PROBE | NETIF_MSG_LINK)
+static int debug = -1;
+module_param(debug, int, 0);
+MODULE_PARM_DESC(debug, "Debug level (0=none,...,16=all)");
+
+/* SRAM memory layout:
+ *
+ * 0x0000-0x05ff TX buffers 1.5KB (1*1536) reside in the GP area in SRAM
+ * 0x0600-0x5fff RX buffers 22.5KB (15*1536) reside in the RX area in SRAM
+ */
+#define ENC_TX_BUF_START 0x0000U
+#define ENC_RX_BUF_START 0x0600U
+#define ENC_RX_BUF_END 0x5fffU
+#define ENC_SRAM_SIZE 0x6000U
+
+enum {
+ RXFILTER_NORMAL,
+ RXFILTER_MULTI,
+ RXFILTER_PROMISC
+};
+
+struct encx24j600_priv {
+ struct net_device *ndev;
+ struct mutex lock; /* device access lock */
+ struct encx24j600_context ctx;
+ struct sk_buff *tx_skb;
+ struct task_struct *kworker_task;
+ struct kthread_worker kworker;
+ struct kthread_work tx_work;
+ struct kthread_work setrx_work;
+ u16 next_packet;
+ bool hw_enabled;
+ bool full_duplex;
+ bool autoneg;
+ u16 speed;
+ int rxfilter;
+ u32 msg_enable;
+};
+
+static void dump_packet(const char *msg, int len, const char *data)
+{
+ pr_debug(DRV_NAME ": %s - packet len:%d\n", msg, len);
+ print_hex_dump_bytes("pk data: ", DUMP_PREFIX_OFFSET, data, len);
+}
+
+static void encx24j600_dump_rsv(struct encx24j600_priv *priv, const char *msg,
+ struct rsv *rsv)
+{
+ struct net_device *dev = priv->ndev;
+
+ netdev_info(dev, "RX packet Len:%d\n", rsv->len);
+ netdev_dbg(dev, "%s - NextPk: 0x%04x\n", msg,
+ rsv->next_packet);
+ netdev_dbg(dev, "RxOK: %d, DribbleNibble: %d\n",
+ RSV_GETBIT(rsv->rxstat, RSV_RXOK),
+ RSV_GETBIT(rsv->rxstat, RSV_DRIBBLENIBBLE));
+ netdev_dbg(dev, "CRCErr:%d, LenChkErr: %d, LenOutOfRange: %d\n",
+ RSV_GETBIT(rsv->rxstat, RSV_CRCERROR),
+ RSV_GETBIT(rsv->rxstat, RSV_LENCHECKERR),
+ RSV_GETBIT(rsv->rxstat, RSV_LENOUTOFRANGE));
+ netdev_dbg(dev, "Multicast: %d, Broadcast: %d, LongDropEvent: %d, CarrierEvent: %d\n",
+ RSV_GETBIT(rsv->rxstat, RSV_RXMULTICAST),
+ RSV_GETBIT(rsv->rxstat, RSV_RXBROADCAST),
+ RSV_GETBIT(rsv->rxstat, RSV_RXLONGEVDROPEV),
+ RSV_GETBIT(rsv->rxstat, RSV_CARRIEREV));
+ netdev_dbg(dev, "ControlFrame: %d, PauseFrame: %d, UnknownOp: %d, VLanTagFrame: %d\n",
+ RSV_GETBIT(rsv->rxstat, RSV_RXCONTROLFRAME),
+ RSV_GETBIT(rsv->rxstat, RSV_RXPAUSEFRAME),
+ RSV_GETBIT(rsv->rxstat, RSV_RXUNKNOWNOPCODE),
+ RSV_GETBIT(rsv->rxstat, RSV_RXTYPEVLAN));
+}
+
+static u16 encx24j600_read_reg(struct encx24j600_priv *priv, u8 reg)
+{
+ struct net_device *dev = priv->ndev;
+ unsigned int val = 0;
+ int ret = regmap_read(priv->ctx.regmap, reg, &val);
+ if (unlikely(ret))
+ netif_err(priv, drv, dev, "%s: error %d reading reg %02x\n",
+ __func__, ret, reg);
+ return val;
+}
+
+static void encx24j600_write_reg(struct encx24j600_priv *priv, u8 reg, u16 val)
+{
+ struct net_device *dev = priv->ndev;
+ int ret = regmap_write(priv->ctx.regmap, reg, val);
+ if (unlikely(ret))
+ netif_err(priv, drv, dev, "%s: error %d writing reg %02x=%04x\n",
+ __func__, ret, reg, val);
+}
+
+static void encx24j600_update_reg(struct encx24j600_priv *priv, u8 reg,
+ u16 mask, u16 val)
+{
+ struct net_device *dev = priv->ndev;
+ int ret = regmap_update_bits(priv->ctx.regmap, reg, mask, val);
+ if (unlikely(ret))
+ netif_err(priv, drv, dev, "%s: error %d updating reg %02x=%04x~%04x\n",
+ __func__, ret, reg, val, mask);
+}
+
+static u16 encx24j600_read_phy(struct encx24j600_priv *priv, u8 reg)
+{
+ struct net_device *dev = priv->ndev;
+ unsigned int val = 0;
+ int ret = regmap_read(priv->ctx.phymap, reg, &val);
+ if (unlikely(ret))
+ netif_err(priv, drv, dev, "%s: error %d reading %02x\n",
+ __func__, ret, reg);
+ return val;
+}
+
+static void encx24j600_write_phy(struct encx24j600_priv *priv, u8 reg, u16 val)
+{
+ struct net_device *dev = priv->ndev;
+ int ret = regmap_write(priv->ctx.phymap, reg, val);
+ if (unlikely(ret))
+ netif_err(priv, drv, dev, "%s: error %d writing reg %02x=%04x\n",
+ __func__, ret, reg, val);
+}
+
+static void encx24j600_clr_bits(struct encx24j600_priv *priv, u8 reg, u16 mask)
+{
+ encx24j600_update_reg(priv, reg, mask, 0);
+}
+
+static void encx24j600_set_bits(struct encx24j600_priv *priv, u8 reg, u16 mask)
+{
+ encx24j600_update_reg(priv, reg, mask, mask);
+}
+
+static void encx24j600_cmd(struct encx24j600_priv *priv, u8 cmd)
+{
+ struct net_device *dev = priv->ndev;
+ int ret = regmap_write(priv->ctx.regmap, cmd, 0);
+ if (unlikely(ret))
+ netif_err(priv, drv, dev, "%s: error %d with cmd %02x\n",
+ __func__, ret, cmd);
+}
+
+static int encx24j600_raw_read(struct encx24j600_priv *priv, u8 reg, u8 *data,
+ size_t count)
+{
+ int ret;
+ mutex_lock(&priv->ctx.mutex);
+ ret = regmap_encx24j600_spi_read(&priv->ctx, reg, data, count);
+ mutex_unlock(&priv->ctx.mutex);
+
+ return ret;
+}
+
+static int encx24j600_raw_write(struct encx24j600_priv *priv, u8 reg,
+ const u8 *data, size_t count)
+{
+ int ret;
+ mutex_lock(&priv->ctx.mutex);
+ ret = regmap_encx24j600_spi_write(&priv->ctx, reg, data, count);
+ mutex_unlock(&priv->ctx.mutex);
+
+ return ret;
+}
+
+static void encx24j600_update_phcon1(struct encx24j600_priv *priv)
+{
+ u16 phcon1 = encx24j600_read_phy(priv, PHCON1);
+ if (priv->autoneg == AUTONEG_ENABLE) {
+ phcon1 |= ANEN | RENEG;
+ } else {
+ phcon1 &= ~ANEN;
+ if (priv->speed == SPEED_100)
+ phcon1 |= SPD100;
+ else
+ phcon1 &= ~SPD100;
+
+ if (priv->full_duplex)
+ phcon1 |= PFULDPX;
+ else
+ phcon1 &= ~PFULDPX;
+ }
+ encx24j600_write_phy(priv, PHCON1, phcon1);
+}
+
+/* Waits for autonegotiation to complete. */
+static int encx24j600_wait_for_autoneg(struct encx24j600_priv *priv)
+{
+ struct net_device *dev = priv->ndev;
+ unsigned long timeout = jiffies + msecs_to_jiffies(2000);
+ u16 phstat1;
+ u16 estat;
+ int ret = 0;
+
+ phstat1 = encx24j600_read_phy(priv, PHSTAT1);
+ while ((phstat1 & ANDONE) == 0) {
+ if (time_after(jiffies, timeout)) {
+ u16 phstat3;
+
+ netif_notice(priv, drv, dev, "timeout waiting for autoneg done\n");
+
+ priv->autoneg = AUTONEG_DISABLE;
+ phstat3 = encx24j600_read_phy(priv, PHSTAT3);
+ priv->speed = (phstat3 & PHY3SPD100)
+ ? SPEED_100 : SPEED_10;
+ priv->full_duplex = (phstat3 & PHY3DPX) ? 1 : 0;
+ encx24j600_update_phcon1(priv);
+ netif_notice(priv, drv, dev, "Using parallel detection: %s/%s",
+ priv->speed == SPEED_100 ? "100" : "10",
+ priv->full_duplex ? "Full" : "Half");
+
+ return -ETIMEDOUT;
+ }
+ cpu_relax();
+ phstat1 = encx24j600_read_phy(priv, PHSTAT1);
+ }
+
+ estat = encx24j600_read_reg(priv, ESTAT);
+ if (estat & PHYDPX) {
+ encx24j600_set_bits(priv, MACON2, FULDPX);
+ encx24j600_write_reg(priv, MABBIPG, 0x15);
+ } else {
+ encx24j600_clr_bits(priv, MACON2, FULDPX);
+ encx24j600_write_reg(priv, MABBIPG, 0x12);
+ /* Max retransmittions attempt */
+ encx24j600_write_reg(priv, MACLCON, 0x370f);
+ }
+
+ return ret;
+}
+
+/* Access the PHY to determine link status */
+static void encx24j600_check_link_status(struct encx24j600_priv *priv)
+{
+ struct net_device *dev = priv->ndev;
+ u16 estat;
+
+ estat = encx24j600_read_reg(priv, ESTAT);
+
+ if (estat & PHYLNK) {
+ if (priv->autoneg == AUTONEG_ENABLE)
+ encx24j600_wait_for_autoneg(priv);
+
+ netif_carrier_on(dev);
+ netif_info(priv, ifup, dev, "link up\n");
+ } else {
+ netif_info(priv, ifdown, dev, "link down\n");
+
+ /* Re-enable autoneg since we won't know what we might be
+ * connected to when the link is brought back up again.
+ */
+ priv->autoneg = AUTONEG_ENABLE;
+ priv->full_duplex = true;
+ priv->speed = SPEED_100;
+ netif_carrier_off(dev);
+ }
+}
+
+static void encx24j600_int_link_handler(struct encx24j600_priv *priv)
+{
+ struct net_device *dev = priv->ndev;
+
+ netif_dbg(priv, intr, dev, "%s", __func__);
+ encx24j600_check_link_status(priv);
+ encx24j600_clr_bits(priv, EIR, LINKIF);
+}
+
+static void encx24j600_tx_complete(struct encx24j600_priv *priv, bool err)
+{
+ struct net_device *dev = priv->ndev;
+
+ mutex_lock(&priv->lock);
+
+ if (err)
+ dev->stats.tx_errors++;
+ else
+ dev->stats.tx_packets++;
+
+ dev->stats.tx_bytes += priv->tx_skb->len;
+
+ encx24j600_clr_bits(priv, EIR, TXIF | TXABTIF);
+
+ netif_dbg(priv, tx_done, dev, "TX Done%s\n", err ? ": Err" : "");
+
+ if (priv->tx_skb) {
+ dev_kfree_skb(priv->tx_skb);
+ priv->tx_skb = NULL;
+ }
+
+ netif_wake_queue(dev);
+
+ mutex_unlock(&priv->lock);
+}
+
+static int encx24j600_receive_packet(struct encx24j600_priv *priv,
+ struct rsv *rsv)
+{
+ struct net_device *dev = priv->ndev;
+ struct sk_buff *skb = netdev_alloc_skb(dev, rsv->len + NET_IP_ALIGN);
+ if (!skb) {
+ pr_err_ratelimited("RX: OOM: packet dropped\n");
+ dev->stats.rx_dropped++;
+ return -ENOMEM;
+ }
+ skb_reserve(skb, NET_IP_ALIGN);
+ encx24j600_raw_read(priv, RRXDATA, skb_put(skb, rsv->len), rsv->len);
+
+ if (netif_msg_pktdata(priv))
+ dump_packet("RX", skb->len, skb->data);
+
+ skb->dev = dev;
+ skb->protocol = eth_type_trans(skb, dev);
+ skb->ip_summed = CHECKSUM_COMPLETE;
+
+ /* Maintain stats */
+ dev->stats.rx_packets++;
+ dev->stats.rx_bytes += rsv->len;
+ priv->next_packet = rsv->next_packet;
+
+ netif_rx(skb);
+
+ return 0;
+}
+
+static void encx24j600_rx_packets(struct encx24j600_priv *priv, u8 packet_count)
+{
+ struct net_device *dev = priv->ndev;
+
+ while (packet_count--) {
+ struct rsv rsv;
+ u16 newrxtail;
+
+ encx24j600_write_reg(priv, ERXRDPT, priv->next_packet);
+ encx24j600_raw_read(priv, RRXDATA, (u8 *)&rsv, sizeof(rsv));
+
+ if (netif_msg_rx_status(priv))
+ encx24j600_dump_rsv(priv, __func__, &rsv);
+
+ if (!RSV_GETBIT(rsv.rxstat, RSV_RXOK) ||
+ (rsv.len > MAX_FRAMELEN)) {
+ netif_err(priv, rx_err, dev, "RX Error %04x\n",
+ rsv.rxstat);
+ dev->stats.rx_errors++;
+
+ if (RSV_GETBIT(rsv.rxstat, RSV_CRCERROR))
+ dev->stats.rx_crc_errors++;
+ if (RSV_GETBIT(rsv.rxstat, RSV_LENCHECKERR))
+ dev->stats.rx_frame_errors++;
+ if (rsv.len > MAX_FRAMELEN)
+ dev->stats.rx_over_errors++;
+ } else {
+ encx24j600_receive_packet(priv, &rsv);
+ }
+
+ newrxtail = priv->next_packet - 2;
+ if (newrxtail == ENC_RX_BUF_START)
+ newrxtail = SRAM_SIZE - 2;
+
+ encx24j600_cmd(priv, SETPKTDEC);
+ encx24j600_write_reg(priv, ERXTAIL, newrxtail);
+ }
+}
+
+static irqreturn_t encx24j600_isr(int irq, void *dev_id)
+{
+ struct encx24j600_priv *priv = dev_id;
+ struct net_device *dev = priv->ndev;
+ int eir;
+
+ /* Clear interrupts */
+ encx24j600_cmd(priv, CLREIE);
+
+ eir = encx24j600_read_reg(priv, EIR);
+
+ if (eir & LINKIF)
+ encx24j600_int_link_handler(priv);
+
+ if (eir & TXIF)
+ encx24j600_tx_complete(priv, false);
+
+ if (eir & TXABTIF)
+ encx24j600_tx_complete(priv, true);
+
+ if (eir & RXABTIF) {
+ if (eir & PCFULIF) {
+ /* Packet counter is full */
+ netif_err(priv, rx_err, dev, "Packet counter full\n");
+ }
+ dev->stats.rx_dropped++;
+ encx24j600_clr_bits(priv, EIR, RXABTIF);
+ }
+
+ if (eir & PKTIF) {
+ u8 packet_count;
+
+ mutex_lock(&priv->lock);
+
+ packet_count = encx24j600_read_reg(priv, ESTAT) & 0xff;
+ while (packet_count) {
+ encx24j600_rx_packets(priv, packet_count);
+ packet_count = encx24j600_read_reg(priv, ESTAT) & 0xff;
+ }
+
+ mutex_unlock(&priv->lock);
+ }
+
+ /* Enable interrupts */
+ encx24j600_cmd(priv, SETEIE);
+
+ return IRQ_HANDLED;
+}
+
+static int encx24j600_soft_reset(struct encx24j600_priv *priv)
+{
+ int ret = 0;
+ int timeout;
+ u16 eudast;
+
+ /* Write and verify a test value to EUDAST */
+ regcache_cache_bypass(priv->ctx.regmap, true);
+ timeout = 10;
+ do {
+ encx24j600_write_reg(priv, EUDAST, EUDAST_TEST_VAL);
+ eudast = encx24j600_read_reg(priv, EUDAST);
+ usleep_range(25, 100);
+ } while ((eudast != EUDAST_TEST_VAL) && --timeout);
+ regcache_cache_bypass(priv->ctx.regmap, false);
+
+ if (timeout == 0) {
+ ret = -ETIMEDOUT;
+ goto err_out;
+ }
+
+ /* Wait for CLKRDY to become set */
+ timeout = 10;
+ while (!(encx24j600_read_reg(priv, ESTAT) & CLKRDY) && --timeout)
+ usleep_range(25, 100);
+
+ if (timeout == 0) {
+ ret = -ETIMEDOUT;
+ goto err_out;
+ }
+
+ /* Issue a System Reset command */
+ encx24j600_cmd(priv, SETETHRST);
+ usleep_range(25, 100);
+
+ /* Confirm that EUDAST has 0000h after system reset */
+ if (encx24j600_read_reg(priv, EUDAST) != 0) {
+ ret = -EINVAL;
+ goto err_out;
+ }
+
+ /* Wait for PHY register and status bits to become available */
+ usleep_range(256, 1000);
+
+err_out:
+ return ret;
+}
+
+static int encx24j600_hw_reset(struct encx24j600_priv *priv)
+{
+ int ret;
+
+ mutex_lock(&priv->lock);
+ ret = encx24j600_soft_reset(priv);
+ mutex_unlock(&priv->lock);
+
+ return ret;
+}
+
+static void encx24j600_reset_hw_tx(struct encx24j600_priv *priv)
+{
+ encx24j600_set_bits(priv, ECON2, TXRST);
+ encx24j600_clr_bits(priv, ECON2, TXRST);
+}
+
+static void encx24j600_hw_init_tx(struct encx24j600_priv *priv)
+{
+ /* Reset TX */
+ encx24j600_reset_hw_tx(priv);
+
+ /* Clear the TXIF flag if were previously set */
+ encx24j600_clr_bits(priv, EIR, TXIF | TXABTIF);
+
+ /* Write the Tx Buffer pointer */
+ encx24j600_write_reg(priv, EGPWRPT, ENC_TX_BUF_START);
+}
+
+static void encx24j600_hw_init_rx(struct encx24j600_priv *priv)
+{
+ encx24j600_cmd(priv, DISABLERX);
+
+ /* Set up RX packet start address in the SRAM */
+ encx24j600_write_reg(priv, ERXST, ENC_RX_BUF_START);
+
+ /* Preload the RX Data pointer to the beginning of the RX area */
+ encx24j600_write_reg(priv, ERXRDPT, ENC_RX_BUF_START);
+
+ priv->next_packet = ENC_RX_BUF_START;
+
+ /* Set up RX end address in the SRAM */
+ encx24j600_write_reg(priv, ERXTAIL, ENC_SRAM_SIZE - 2);
+
+ /* Reset the user data pointers */
+ encx24j600_write_reg(priv, EUDAST, ENC_SRAM_SIZE);
+ encx24j600_write_reg(priv, EUDAND, ENC_SRAM_SIZE + 1);
+
+ /* Set Max Frame length */
+ encx24j600_write_reg(priv, MAMXFL, MAX_FRAMELEN);
+}
+
+static void encx24j600_dump_config(struct encx24j600_priv *priv,
+ const char *msg)
+{
+ pr_info(DRV_NAME ": %s\n", msg);
+
+ /* CHIP configuration */
+ pr_info(DRV_NAME " ECON1: %04X\n", encx24j600_read_reg(priv, ECON1));
+ pr_info(DRV_NAME " ECON2: %04X\n", encx24j600_read_reg(priv, ECON2));
+ pr_info(DRV_NAME " ERXFCON: %04X\n", encx24j600_read_reg(priv,
+ ERXFCON));
+ pr_info(DRV_NAME " ESTAT: %04X\n", encx24j600_read_reg(priv, ESTAT));
+ pr_info(DRV_NAME " EIR: %04X\n", encx24j600_read_reg(priv, EIR));
+ pr_info(DRV_NAME " EIDLED: %04X\n", encx24j600_read_reg(priv, EIDLED));
+
+ /* MAC layer configuration */
+ pr_info(DRV_NAME " MACON1: %04X\n", encx24j600_read_reg(priv, MACON1));
+ pr_info(DRV_NAME " MACON2: %04X\n", encx24j600_read_reg(priv, MACON2));
+ pr_info(DRV_NAME " MAIPG: %04X\n", encx24j600_read_reg(priv, MAIPG));
+ pr_info(DRV_NAME " MACLCON: %04X\n", encx24j600_read_reg(priv,
+ MACLCON));
+ pr_info(DRV_NAME " MABBIPG: %04X\n", encx24j600_read_reg(priv,
+ MABBIPG));
+
+ /* PHY configuation */
+ pr_info(DRV_NAME " PHCON1: %04X\n", encx24j600_read_phy(priv, PHCON1));
+ pr_info(DRV_NAME " PHCON2: %04X\n", encx24j600_read_phy(priv, PHCON2));
+ pr_info(DRV_NAME " PHANA: %04X\n", encx24j600_read_phy(priv, PHANA));
+ pr_info(DRV_NAME " PHANLPA: %04X\n", encx24j600_read_phy(priv,
+ PHANLPA));
+ pr_info(DRV_NAME " PHANE: %04X\n", encx24j600_read_phy(priv, PHANE));
+ pr_info(DRV_NAME " PHSTAT1: %04X\n", encx24j600_read_phy(priv,
+ PHSTAT1));
+ pr_info(DRV_NAME " PHSTAT2: %04X\n", encx24j600_read_phy(priv,
+ PHSTAT2));
+ pr_info(DRV_NAME " PHSTAT3: %04X\n", encx24j600_read_phy(priv,
+ PHSTAT3));
+}
+
+static void encx24j600_set_rxfilter_mode(struct encx24j600_priv *priv)
+{
+ switch (priv->rxfilter) {
+ case RXFILTER_PROMISC:
+ encx24j600_set_bits(priv, MACON1, PASSALL);
+ encx24j600_write_reg(priv, ERXFCON, UCEN | MCEN | NOTMEEN);
+ break;
+ case RXFILTER_MULTI:
+ encx24j600_clr_bits(priv, MACON1, PASSALL);
+ encx24j600_write_reg(priv, ERXFCON, UCEN | CRCEN | BCEN | MCEN);
+ break;
+ case RXFILTER_NORMAL:
+ default:
+ encx24j600_clr_bits(priv, MACON1, PASSALL);
+ encx24j600_write_reg(priv, ERXFCON, UCEN | CRCEN | BCEN);
+ break;
+ }
+}
+
+static int encx24j600_hw_init(struct encx24j600_priv *priv)
+{
+ struct net_device *dev = priv->ndev;
+ int ret = 0;
+ u16 eidled;
+ u16 macon2;
+
+ priv->hw_enabled = false;
+
+ eidled = encx24j600_read_reg(priv, EIDLED);
+ if (((eidled & DEVID_MASK) >> DEVID_SHIFT) != ENCX24J600_DEV_ID) {
+ ret = -EINVAL;
+ goto err_out;
+ }
+
+ netif_info(priv, drv, dev, "Silicon rev ID: 0x%02x\n",
+ (eidled & REVID_MASK) >> REVID_SHIFT);
+
+ /* PHY Leds: link status,
+ * LEDA: Link + transmit/receive events
+ * LEDB: Link State + colision events
+ */
+ encx24j600_update_reg(priv, EIDLED, 0xbc00, 0xbc00);
+
+ /* Loopback disabled */
+ encx24j600_write_reg(priv, MACON1, 0x9);
+
+ /* interpacket gap value */
+ encx24j600_write_reg(priv, MAIPG, 0x0c12);
+
+ /* Write the auto negotiation pattern */
+ encx24j600_write_phy(priv, PHANA, PHANA_DEFAULT);
+
+ encx24j600_update_phcon1(priv);
+ encx24j600_check_link_status(priv);
+
+ macon2 = MACON2_RSV1 | TXCRCEN | PADCFG0 | PADCFG2 | MACON2_DEFER;
+ if ((priv->autoneg == AUTONEG_DISABLE) && priv->full_duplex)
+ macon2 |= FULDPX;
+
+ encx24j600_set_bits(priv, MACON2, macon2);
+
+ priv->rxfilter = RXFILTER_NORMAL;
+ encx24j600_set_rxfilter_mode(priv);
+
+ /* Program the Maximum frame length */
+ encx24j600_write_reg(priv, MAMXFL, MAX_FRAMELEN);
+
+ /* Init Tx pointers */
+ encx24j600_hw_init_tx(priv);
+
+ /* Init Rx pointers */
+ encx24j600_hw_init_rx(priv);
+
+ if (netif_msg_hw(priv))
+ encx24j600_dump_config(priv, "Hw is initialized");
+
+err_out:
+ return ret;
+}
+
+static void encx24j600_hw_enable(struct encx24j600_priv *priv)
+{
+ /* Clear the interrupt flags in case was set */
+ encx24j600_clr_bits(priv, EIR, (PCFULIF | RXABTIF | TXABTIF | TXIF |
+ PKTIF | LINKIF));
+
+ /* Enable the interrupts */
+ encx24j600_write_reg(priv, EIE, (PCFULIE | RXABTIE | TXABTIE | TXIE |
+ PKTIE | LINKIE | INTIE));
+
+ /* Enable RX */
+ encx24j600_cmd(priv, ENABLERX);
+
+ priv->hw_enabled = true;
+}
+
+static void encx24j600_hw_disable(struct encx24j600_priv *priv)
+{
+ /* Disable all interrupts */
+ encx24j600_write_reg(priv, EIE, 0);
+
+ /* Disable RX */
+ encx24j600_cmd(priv, DISABLERX);
+
+ priv->hw_enabled = false;
+}
+
+static int encx24j600_setlink(struct net_device *dev, u8 autoneg, u16 speed,
+ u8 duplex)
+{
+ struct encx24j600_priv *priv = netdev_priv(dev);
+ int ret = 0;
+
+ if (!priv->hw_enabled) {
+ /* link is in low power mode now; duplex setting
+ * will take effect on next encx24j600_hw_init()
+ */
+ if (speed == SPEED_10 || speed == SPEED_100) {
+ priv->autoneg = (autoneg == AUTONEG_ENABLE);
+ priv->full_duplex = (duplex == DUPLEX_FULL);
+ priv->speed = (speed == SPEED_100);
+ } else {
+ netif_warn(priv, link, dev, "unsupported link speed setting\n");
+ /*speeds other than SPEED_10 and SPEED_100 */
+ /*are not supported by chip */
+ ret = -EOPNOTSUPP;
+ }
+ } else {
+ netif_warn(priv, link, dev, "Warning: hw must be disabled to set link mode\n");
+ ret = -EBUSY;
+ }
+ return ret;
+}
+
+static void encx24j600_hw_get_macaddr(struct encx24j600_priv *priv,
+ unsigned char *ethaddr)
+{
+ unsigned short val;
+
+ val = encx24j600_read_reg(priv, MAADR1);
+
+ ethaddr[0] = val & 0x00ff;
+ ethaddr[1] = (val & 0xff00) >> 8;
+
+ val = encx24j600_read_reg(priv, MAADR2);
+
+ ethaddr[2] = val & 0x00ffU;
+ ethaddr[3] = (val & 0xff00U) >> 8;
+
+ val = encx24j600_read_reg(priv, MAADR3);
+
+ ethaddr[4] = val & 0x00ffU;
+ ethaddr[5] = (val & 0xff00U) >> 8;
+}
+
+/* Program the hardware MAC address from dev->dev_addr.*/
+static int encx24j600_set_hw_macaddr(struct net_device *dev)
+{
+ struct encx24j600_priv *priv = netdev_priv(dev);
+
+ if (priv->hw_enabled) {
+ netif_info(priv, drv, dev, "Hardware must be disabled to set Mac address\n");
+ return -EBUSY;
+ }
+
+ mutex_lock(&priv->lock);
+
+ netif_info(priv, drv, dev, "%s: Setting MAC address to %pM\n",
+ dev->name, dev->dev_addr);
+
+ encx24j600_write_reg(priv, MAADR3, (dev->dev_addr[4] |
+ dev->dev_addr[5] << 8));
+ encx24j600_write_reg(priv, MAADR2, (dev->dev_addr[2] |
+ dev->dev_addr[3] << 8));
+ encx24j600_write_reg(priv, MAADR1, (dev->dev_addr[0] |
+ dev->dev_addr[1] << 8));
+
+ mutex_unlock(&priv->lock);
+
+ return 0;
+}
+
+/* Store the new hardware address in dev->dev_addr, and update the MAC.*/
+static int encx24j600_set_mac_address(struct net_device *dev, void *addr)
+{
+ struct sockaddr *address = addr;
+
+ if (netif_running(dev))
+ return -EBUSY;
+ if (!is_valid_ether_addr(address->sa_data))
+ return -EADDRNOTAVAIL;
+
+ memcpy(dev->dev_addr, address->sa_data, dev->addr_len);
+ return encx24j600_set_hw_macaddr(dev);
+}
+
+static int encx24j600_open(struct net_device *dev)
+{
+ struct encx24j600_priv *priv = netdev_priv(dev);
+
+ int ret = request_threaded_irq(priv->ctx.spi->irq, NULL, encx24j600_isr,
+ IRQF_TRIGGER_FALLING | IRQF_ONESHOT,
+ DRV_NAME, priv);
+ if (unlikely(ret < 0)) {
+ netdev_err(dev, "request irq %d failed (ret = %d)\n",
+ priv->ctx.spi->irq, ret);
+ return ret;
+ }
+
+ encx24j600_hw_disable(priv);
+ encx24j600_hw_init(priv);
+ encx24j600_hw_enable(priv);
+ netif_start_queue(dev);
+
+ return 0;
+}
+
+static int encx24j600_stop(struct net_device *dev)
+{
+ struct encx24j600_priv *priv = netdev_priv(dev);
+
+ netif_stop_queue(dev);
+ free_irq(priv->ctx.spi->irq, priv);
+ return 0;
+}
+
+static void encx24j600_setrx_proc(struct kthread_work *ws)
+{
+ struct encx24j600_priv *priv =
+ container_of(ws, struct encx24j600_priv, setrx_work);
+
+ mutex_lock(&priv->lock);
+ encx24j600_set_rxfilter_mode(priv);
+ mutex_unlock(&priv->lock);
+}
+
+static void encx24j600_set_multicast_list(struct net_device *dev)
+{
+ struct encx24j600_priv *priv = netdev_priv(dev);
+ int oldfilter = priv->rxfilter;
+
+ if (dev->flags & IFF_PROMISC) {
+ netif_dbg(priv, link, dev, "promiscuous mode\n");
+ priv->rxfilter = RXFILTER_PROMISC;
+ } else if ((dev->flags & IFF_ALLMULTI) || !netdev_mc_empty(dev)) {
+ netif_dbg(priv, link, dev, "%smulticast mode\n",
+ (dev->flags & IFF_ALLMULTI) ? "all-" : "");
+ priv->rxfilter = RXFILTER_MULTI;
+ } else {
+ netif_dbg(priv, link, dev, "normal mode\n");
+ priv->rxfilter = RXFILTER_NORMAL;
+ }
+
+ if (oldfilter != priv->rxfilter)
+ queue_kthread_work(&priv->kworker, &priv->setrx_work);
+}
+
+static void encx24j600_hw_tx(struct encx24j600_priv *priv)
+{
+ struct net_device *dev = priv->ndev;
+ netif_info(priv, tx_queued, dev, "TX Packet Len:%d\n",
+ priv->tx_skb->len);
+
+ if (netif_msg_pktdata(priv))
+ dump_packet("TX", priv->tx_skb->len, priv->tx_skb->data);
+
+ if (encx24j600_read_reg(priv, EIR) & TXABTIF)
+ /* Last transmition aborted due to error. Reset TX interface */
+ encx24j600_reset_hw_tx(priv);
+
+ /* Clear the TXIF flag if were previously set */
+ encx24j600_clr_bits(priv, EIR, TXIF);
+
+ /* Set the data pointer to the TX buffer address in the SRAM */
+ encx24j600_write_reg(priv, EGPWRPT, ENC_TX_BUF_START);
+
+ /* Copy the packet into the SRAM */
+ encx24j600_raw_write(priv, WGPDATA, (u8 *)priv->tx_skb->data,
+ priv->tx_skb->len);
+
+ /* Program the Tx buffer start pointer */
+ encx24j600_write_reg(priv, ETXST, ENC_TX_BUF_START);
+
+ /* Program the packet length */
+ encx24j600_write_reg(priv, ETXLEN, priv->tx_skb->len);
+
+ /* Start the transmission */
+ encx24j600_cmd(priv, SETTXRTS);
+}
+
+static void encx24j600_tx_proc(struct kthread_work *ws)
+{
+ struct encx24j600_priv *priv =
+ container_of(ws, struct encx24j600_priv, tx_work);
+
+ mutex_lock(&priv->lock);
+ encx24j600_hw_tx(priv);
+ mutex_unlock(&priv->lock);
+}
+
+static netdev_tx_t encx24j600_tx(struct sk_buff *skb, struct net_device *dev)
+{
+ struct encx24j600_priv *priv = netdev_priv(dev);
+
+ netif_stop_queue(dev);
+
+ /* save the timestamp */
+ dev->trans_start = jiffies;
+
+ /* Remember the skb for deferred processing */
+ priv->tx_skb = skb;
+
+ queue_kthread_work(&priv->kworker, &priv->tx_work);
+
+ return NETDEV_TX_OK;
+}
+
+/* Deal with a transmit timeout */
+static void encx24j600_tx_timeout(struct net_device *dev)
+{
+ struct encx24j600_priv *priv = netdev_priv(dev);
+
+ netif_err(priv, tx_err, dev, "TX timeout at %ld, latency %ld\n",
+ jiffies, jiffies - dev->trans_start);
+
+ dev->stats.tx_errors++;
+ netif_wake_queue(dev);
+ return;
+}
+
+static int encx24j600_get_regs_len(struct net_device *dev)
+{
+ return SFR_REG_COUNT;
+}
+
+static void encx24j600_get_regs(struct net_device *dev,
+ struct ethtool_regs *regs, void *p)
+{
+ struct encx24j600_priv *priv = netdev_priv(dev);
+ u16 *buff = p;
+ u8 reg;
+
+ regs->version = 1;
+ mutex_lock(&priv->lock);
+ for (reg = 0; reg < SFR_REG_COUNT; reg += 2) {
+ unsigned int val = 0;
+ /* ignore errors for unreadable registers */
+ regmap_read(priv->ctx.regmap, reg, &val);
+ buff[reg] = val & 0xffff;
+ }
+ mutex_unlock(&priv->lock);
+}
+
+static void encx24j600_get_drvinfo(struct net_device *dev,
+ struct ethtool_drvinfo *info)
+{
+ strlcpy(info->driver, DRV_NAME, sizeof(info->driver));
+ strlcpy(info->version, DRV_VERSION, sizeof(info->version));
+ strlcpy(info->bus_info, dev_name(dev->dev.parent),
+ sizeof(info->bus_info));
+}
+
+static int encx24j600_get_settings(struct net_device *dev,
+ struct ethtool_cmd *cmd)
+{
+ struct encx24j600_priv *priv = netdev_priv(dev);
+
+ cmd->transceiver = XCVR_INTERNAL;
+ cmd->supported = SUPPORTED_10baseT_Half | SUPPORTED_10baseT_Full |
+ SUPPORTED_100baseT_Half | SUPPORTED_100baseT_Full |
+ SUPPORTED_Autoneg | SUPPORTED_TP;
+
+ ethtool_cmd_speed_set(cmd, priv->speed);
+ cmd->duplex = priv->full_duplex ? DUPLEX_FULL : DUPLEX_HALF;
+ cmd->port = PORT_TP;
+ cmd->autoneg = priv->autoneg ? AUTONEG_ENABLE : AUTONEG_DISABLE;
+
+ return 0;
+}
+
+static int encx24j600_set_settings(struct net_device *dev,
+ struct ethtool_cmd *cmd)
+{
+ return encx24j600_setlink(dev, cmd->autoneg,
+ ethtool_cmd_speed(cmd), cmd->duplex);
+}
+
+static u32 encx24j600_get_msglevel(struct net_device *dev)
+{
+ struct encx24j600_priv *priv = netdev_priv(dev);
+ return priv->msg_enable;
+}
+
+static void encx24j600_set_msglevel(struct net_device *dev, u32 val)
+{
+ struct encx24j600_priv *priv = netdev_priv(dev);
+ priv->msg_enable = val;
+}
+
+static const struct ethtool_ops encx24j600_ethtool_ops = {
+ .get_settings = encx24j600_get_settings,
+ .set_settings = encx24j600_set_settings,
+ .get_drvinfo = encx24j600_get_drvinfo,
+ .get_msglevel = encx24j600_get_msglevel,
+ .set_msglevel = encx24j600_set_msglevel,
+ .get_regs_len = encx24j600_get_regs_len,
+ .get_regs = encx24j600_get_regs,
+};
+
+static const struct net_device_ops encx24j600_netdev_ops = {
+ .ndo_open = encx24j600_open,
+ .ndo_stop = encx24j600_stop,
+ .ndo_start_xmit = encx24j600_tx,
+ .ndo_set_rx_mode = encx24j600_set_multicast_list,
+ .ndo_set_mac_address = encx24j600_set_mac_address,
+ .ndo_tx_timeout = encx24j600_tx_timeout,
+ .ndo_validate_addr = eth_validate_addr,
+};
+
+static int encx24j600_spi_probe(struct spi_device *spi)
+{
+ int ret;
+
+ struct net_device *ndev;
+ struct encx24j600_priv *priv;
+
+ ndev = alloc_etherdev(sizeof(struct encx24j600_priv));
+
+ if (!ndev) {
+ ret = -ENOMEM;
+ goto error_out;
+ }
+
+ priv = netdev_priv(ndev);
+ spi_set_drvdata(spi, priv);
+ dev_set_drvdata(&spi->dev, priv);
+ SET_NETDEV_DEV(ndev, &spi->dev);
+
+ priv->msg_enable = netif_msg_init(debug, DEFAULT_MSG_ENABLE);
+ priv->ndev = ndev;
+
+ /* Default configuration PHY configuration */
+ priv->full_duplex = true;
+ priv->autoneg = AUTONEG_ENABLE;
+ priv->speed = SPEED_100;
+
+ priv->ctx.spi = spi;
+ devm_regmap_init_encx24j600(&spi->dev, &priv->ctx);
+ ndev->irq = spi->irq;
+ ndev->netdev_ops = &encx24j600_netdev_ops;
+
+ mutex_init(&priv->lock);
+
+ /* Reset device and check if it is connected */
+ if (encx24j600_hw_reset(priv)) {
+ netif_err(priv, probe, ndev,
+ DRV_NAME ": Chip is not detected\n");
+ ret = -EIO;
+ goto out_free;
+ }
+
+ /* Initialize the device HW to the consistent state */
+ if (encx24j600_hw_init(priv)) {
+ netif_err(priv, probe, ndev,
+ DRV_NAME ": HW initialization error\n");
+ ret = -EIO;
+ goto out_free;
+ }
+
+ init_kthread_worker(&priv->kworker);
+ init_kthread_work(&priv->tx_work, encx24j600_tx_proc);
+ init_kthread_work(&priv->setrx_work, encx24j600_setrx_proc);
+
+ priv->kworker_task = kthread_run(kthread_worker_fn, &priv->kworker,
+ "encx24j600");
+
+ if (IS_ERR(priv->kworker_task)) {
+ ret = PTR_ERR(priv->kworker_task);
+ goto out_free;
+ }
+
+ /* Get the MAC address from the chip */
+ encx24j600_hw_get_macaddr(priv, ndev->dev_addr);
+
+ ndev->ethtool_ops = &encx24j600_ethtool_ops;
+
+ ret = register_netdev(ndev);
+ if (unlikely(ret)) {
+ netif_err(priv, probe, ndev, "Error %d initializing card encx24j600 card\n",
+ ret);
+ goto out_free;
+ }
+
+ netif_info(priv, drv, priv->ndev, "MAC address %pM\n", ndev->dev_addr);
+
+ return ret;
+
+out_free:
+ free_netdev(ndev);
+
+error_out:
+ return ret;
+}
+
+static int encx24j600_spi_remove(struct spi_device *spi)
+{
+ struct encx24j600_priv *priv = dev_get_drvdata(&spi->dev);
+
+ unregister_netdev(priv->ndev);
+
+ free_netdev(priv->ndev);
+
+ return 0;
+}
+
+static const struct spi_device_id encx24j600_spi_id_table = {
+ .name = "encx24j600"
+};
+
+static struct spi_driver encx24j600_spi_net_driver = {
+ .driver = {
+ .name = DRV_NAME,
+ .owner = THIS_MODULE,
+ .bus = &spi_bus_type,
+ },
+ .probe = encx24j600_spi_probe,
+ .remove = encx24j600_spi_remove,
+ .id_table = &encx24j600_spi_id_table,
+};
+
+static int __init encx24j600_init(void)
+{
+ return spi_register_driver(&encx24j600_spi_net_driver);
+}
+module_init(encx24j600_init);
+
+static void encx24j600_exit(void)
+{
+ spi_unregister_driver(&encx24j600_spi_net_driver);
+}
+module_exit(encx24j600_exit);
+
+MODULE_DESCRIPTION(DRV_NAME " ethernet driver");
+MODULE_AUTHOR("Jon Ringle <jringle@...dpoint.com>");
+MODULE_LICENSE("GPL");
+MODULE_ALIAS("spi:" DRV_NAME);
diff --git a/drivers/net/ethernet/microchip/encx24j600_hw.h b/drivers/net/ethernet/microchip/encx24j600_hw.h
new file mode 100644
index 0000000..4be73d5
--- /dev/null
+++ b/drivers/net/ethernet/microchip/encx24j600_hw.h
@@ -0,0 +1,437 @@
+/**
+ * encx24j600_hw.h: Register definitions
+ *
+ */
+
+#ifndef _ENCX24J600_HW_H
+#define _ENCX24J600_HW_H
+
+struct encx24j600_context {
+ struct spi_device *spi;
+ struct regmap *regmap;
+ struct regmap *phymap;
+ struct mutex mutex; /* mutex to protect access to regmap */
+ int bank;
+};
+
+void devm_regmap_init_encx24j600(struct device *dev,
+ struct encx24j600_context *ctx);
+
+/* Single-byte instructions */
+#define BANK_SELECT(bank) (0xC0 | ((bank & (BANK_MASK >> BANK_SHIFT)) << 1))
+#define B0SEL 0xC0 /* Bank 0 Select */
+#define B1SEL 0xC2 /* Bank 1 Select */
+#define B2SEL 0xC4 /* Bank 2 Select */
+#define B3SEL 0xC6 /* Bank 3 Select */
+#define SETETHRST 0xCA /* System Reset */
+#define FCDISABLE 0xE0 /* Flow Control Disable */
+#define FCSINGLE 0xE2 /* Flow Control Single */
+#define FCMULTIPLE 0xE4 /* Flow Control Multiple */
+#define FCCLEAR 0xE6 /* Flow Control Clear */
+#define SETPKTDEC 0xCC /* Decrement Packet Counter */
+#define DMASTOP 0xD2 /* DMA Stop */
+#define DMACKSUM 0xD8 /* DMA Start Checksum */
+#define DMACKSUMS 0xDA /* DMA Start Checksum with Seed */
+#define DMACOPY 0xDC /* DMA Start Copy */
+#define DMACOPYS 0xDE /* DMA Start Copy and Checksum with Seed */
+#define SETTXRTS 0xD4 /* Request Packet Transmission */
+#define ENABLERX 0xE8 /* Enable RX */
+#define DISABLERX 0xEA /* Disable RX */
+#define SETEIE 0xEC /* Enable Interrupts */
+#define CLREIE 0xEE /* Disable Interrupts */
+
+/* Two byte instructions */
+#define RBSEL 0xC8 /* Read Bank Select */
+
+/* Three byte instructions */
+#define WGPRDPT 0x60 /* Write EGPRDPT */
+#define RGPRDPT 0x62 /* Read EGPRDPT */
+#define WRXRDPT 0x64 /* Write ERXRDPT */
+#define RRXRDPT 0x66 /* Read ERXRDPT */
+#define WUDARDPT 0x68 /* Write EUDARDPT */
+#define RUDARDPT 0x6A /* Read EUDARDPT */
+#define WGPWRPT 0x6C /* Write EGPWRPT */
+#define RGPWRPT 0x6E /* Read EGPWRPT */
+#define WRXWRPT 0x70 /* Write ERXWRPT */
+#define RRXWRPT 0x72 /* Read ERXWRPT */
+#define WUDAWRPT 0x74 /* Write EUDAWRPT */
+#define RUDAWRPT 0x76 /* Read EUDAWRPT */
+
+/* n byte instructions */
+#define RCRCODE 0x00
+#define WCRCODE 0x40
+#define BFSCODE 0x80
+#define BFCCODE 0xA0
+#define RCR(addr) (RCRCODE | (addr & ADDR_MASK)) /* Read Control Register */
+#define WCR(addr) (WCRCODE | (addr & ADDR_MASK)) /* Write Control Register */
+#define RCRU 0x20 /* Read Control Register Unbanked */
+#define WCRU 0x22 /* Write Control Register Unbanked */
+#define BFS(addr) (BFSCODE | (addr & ADDR_MASK)) /* Bit Field Set */
+#define BFC(addr) (BFCCODE | (addr & ADDR_MASK)) /* Bit Field Clear */
+#define BFSU 0x24 /* Bit Field Set Unbanked */
+#define BFCU 0x26 /* Bit Field Clear Unbanked */
+#define RGPDATA 0x28 /* Read EGPDATA */
+#define WGPDATA 0x2A /* Write EGPDATA */
+#define RRXDATA 0x2C /* Read ERXDATA */
+#define WRXDATA 0x2E /* Write ERXDATA */
+#define RUDADATA 0x30 /* Read EUDADATA */
+#define WUDADATA 0x32 /* Write EUDADATA */
+
+#define SFR_REG_COUNT 0xA0
+
+/* ENC424J600 Control Registers
+ * Control register definitions are a combination of address
+ * and bank number
+ * - Register address (bits 0-4)
+ * - Bank number (bits 5-6)
+ */
+#define ADDR_MASK 0x1F
+#define BANK_MASK 0x60
+#define BANK_SHIFT 5
+
+/* All-bank registers */
+#define EUDAST 0x16
+#define EUDAND 0x18
+#define ESTAT 0x1A
+#define EIR 0x1C
+#define ECON1 0x1E
+
+/* Bank 0 registers */
+#define ETXST (0x00 | 0x00)
+#define ETXLEN (0x02 | 0x00)
+#define ERXST (0x04 | 0x00)
+#define ERXTAIL (0x06 | 0x00)
+#define ERXHEAD (0x08 | 0x00)
+#define EDMAST (0x0A | 0x00)
+#define EDMALEN (0x0C | 0x00)
+#define EDMADST (0x0E | 0x00)
+#define EDMACS (0x10 | 0x00)
+#define ETXSTAT (0x12 | 0x00)
+#define ETXWIRE (0x14 | 0x00)
+
+/* Bank 1 registers */
+#define EHT1 (0x00 | 0x20)
+#define EHT2 (0x02 | 0x20)
+#define EHT3 (0x04 | 0x20)
+#define EHT4 (0x06 | 0x20)
+#define EPMM1 (0x08 | 0x20)
+#define EPMM2 (0x0A | 0x20)
+#define EPMM3 (0x0C | 0x20)
+#define EPMM4 (0x0E | 0x20)
+#define EPMCS (0x10 | 0x20)
+#define EPMO (0x12 | 0x20)
+#define ERXFCON (0x14 | 0x20)
+
+/* Bank 2 registers */
+#define MACON1 (0x00 | 0x40)
+#define MACON2 (0x02 | 0x40)
+#define MABBIPG (0x04 | 0x40)
+#define MAIPG (0x06 | 0x40)
+#define MACLCON (0x08 | 0x40)
+#define MAMXFL (0x0A | 0x40)
+#define MICMD (0x12 | 0x40)
+#define MIREGADR (0x14 | 0x40)
+
+/* Bank 3 registers */
+#define MAADR3 (0x00 | 0x60)
+#define MAADR2 (0x02 | 0x60)
+#define MAADR1 (0x04 | 0x60)
+#define MIWR (0x06 | 0x60)
+#define MIRD (0x08 | 0x60)
+#define MISTAT (0x0A | 0x60)
+#define EPAUS (0x0C | 0x60)
+#define ECON2 (0x0E | 0x60)
+#define ERXWM (0x10 | 0x60)
+#define EIE (0x12 | 0x60)
+#define EIDLED (0x14 | 0x60)
+
+/* Unbanked registers */
+#define EGPDATA (0x00 | 0x80)
+#define ERXDATA (0x02 | 0x80)
+#define EUDADATA (0x04 | 0x80)
+#define EGPRDPT (0x06 | 0x80)
+#define EGPWRPT (0x08 | 0x80)
+#define ERXRDPT (0x0A | 0x80)
+#define ERXWRPT (0x0C | 0x80)
+#define EUDARDPT (0x0E | 0x80)
+#define EUDAWRPT (0x10 | 0x80)
+
+
+/* Register bit definitions */
+/* ESTAT */
+#define INT (1 << 15)
+#define FCIDLE (1 << 14)
+#define RXBUSY (1 << 13)
+#define CLKRDY (1 << 12)
+#define PHYDPX (1 << 10)
+#define PHYLNK (1 << 8)
+
+/* EIR */
+#define CRYPTEN (1 << 15)
+#define MODEXIF (1 << 14)
+#define HASHIF (1 << 13)
+#define AESIF (1 << 12)
+#define LINKIF (1 << 11)
+#define PKTIF (1 << 6)
+#define DMAIF (1 << 5)
+#define TXIF (1 << 3)
+#define TXABTIF (1 << 2)
+#define RXABTIF (1 << 1)
+#define PCFULIF (1 << 0)
+
+/* ECON1 */
+#define MODEXST (1 << 15)
+#define HASHEN (1 << 14)
+#define HASHOP (1 << 13)
+#define HASHLST (1 << 12)
+#define AESST (1 << 11)
+#define AESOP1 (1 << 10)
+#define AESOP0 (1 << 9)
+#define PKTDEC (1 << 8)
+#define FCOP1 (1 << 7)
+#define FCOP0 (1 << 6)
+#define DMAST (1 << 5)
+#define DMACPY (1 << 4)
+#define DMACSSD (1 << 3)
+#define DMANOCS (1 << 2)
+#define TXRTS (1 << 1)
+#define RXEN (1 << 0)
+
+/* ETXSTAT */
+#define LATECOL (1 << 10)
+#define MAXCOL (1 << 9)
+#define EXDEFER (1 << 8)
+#define ETXSTATL_DEFER (1 << 7)
+#define CRCBAD (1 << 4)
+#define COLCNT_MASK 0xF
+
+/* ERXFCON */
+#define HTEN (1 << 15)
+#define MPEN (1 << 14)
+#define NOTPM (1 << 12)
+#define PMEN3 (1 << 11)
+#define PMEN2 (1 << 10)
+#define PMEN1 (1 << 9)
+#define PMEN0 (1 << 8)
+#define CRCEEN (1 << 7)
+#define CRCEN (1 << 6)
+#define RUNTEEN (1 << 5)
+#define RUNTEN (1 << 4)
+#define UCEN (1 << 3)
+#define NOTMEEN (1 << 2)
+#define MCEN (1 << 1)
+#define BCEN (1 << 0)
+
+/* MACON1 */
+#define LOOPBK (1 << 4)
+#define RXPAUS (1 << 2)
+#define PASSALL (1 << 1)
+
+/* MACON2 */
+#define MACON2_DEFER (1 << 14)
+#define BPEN (1 << 13)
+#define NOBKOFF (1 << 12)
+#define PADCFG2 (1 << 7)
+#define PADCFG1 (1 << 6)
+#define PADCFG0 (1 << 5)
+#define TXCRCEN (1 << 4)
+#define PHDREN (1 << 3)
+#define HFRMEN (1 << 2)
+#define MACON2_RSV1 (1 << 1)
+#define FULDPX (1 << 0)
+
+/* MAIPG */
+/* value of the high byte is given by the reserved bits,
+ * value of the low byte is recomended setting of the
+ * IPG parameter.
+ */
+#define MAIPGH_VAL 0x0C
+#define MAIPGL_VAL 0x12
+
+/* MIREGADRH */
+#define MIREGADR_VAL (1 << 8)
+
+/* MIREGADRL */
+#define PHREG_MASK 0x1F
+
+/* MICMD */
+#define MIISCAN (1 << 1)
+#define MIIRD (1 << 0)
+
+/* MISTAT */
+#define NVALID (1 << 2)
+#define SCAN (1 << 1)
+#define BUSY (1 << 0)
+
+/* ECON2 */
+#define ETHEN (1 << 15)
+#define STRCH (1 << 14)
+#define TXMAC (1 << 13)
+#define SHA1MD5 (1 << 12)
+#define COCON3 (1 << 11)
+#define COCON2 (1 << 10)
+#define COCON1 (1 << 9)
+#define COCON0 (1 << 8)
+#define AUTOFC (1 << 7)
+#define TXRST (1 << 6)
+#define RXRST (1 << 5)
+#define ETHRST (1 << 4)
+#define MODLEN1 (1 << 3)
+#define MODLEN0 (1 << 2)
+#define AESLEN1 (1 << 1)
+#define AESLEN0 (1 << 0)
+
+/* EIE */
+#define INTIE (1 << 15)
+#define MODEXIE (1 << 14)
+#define HASHIE (1 << 13)
+#define AESIE (1 << 12)
+#define LINKIE (1 << 11)
+#define PKTIE (1 << 6)
+#define DMAIE (1 << 5)
+#define TXIE (1 << 3)
+#define TXABTIE (1 << 2)
+#define RXABTIE (1 << 1)
+#define PCFULIE (1 << 0)
+
+/* EIDLED */
+#define LACFG3 (1 << 15)
+#define LACFG2 (1 << 14)
+#define LACFG1 (1 << 13)
+#define LACFG0 (1 << 12)
+#define LBCFG3 (1 << 11)
+#define LBCFG2 (1 << 10)
+#define LBCFG1 (1 << 9)
+#define LBCFG0 (1 << 8)
+#define DEVID_SHIFT 5
+#define DEVID_MASK (0x7 << DEVID_SHIFT)
+#define REVID_SHIFT 0
+#define REVID_MASK (0x1F << REVID_SHIFT)
+
+/* PHY registers */
+#define PHCON1 0x00
+#define PHSTAT1 0x01
+#define PHANA 0x04
+#define PHANLPA 0x05
+#define PHANE 0x06
+#define PHCON2 0x11
+#define PHSTAT2 0x1B
+#define PHSTAT3 0x1F
+
+/* PHCON1 */
+#define PRST (1 << 15)
+#define PLOOPBK (1 << 14)
+#define SPD100 (1 << 13)
+#define ANEN (1 << 12)
+#define PSLEEP (1 << 11)
+#define RENEG (1 << 9)
+#define PFULDPX (1 << 8)
+
+/* PHSTAT1 */
+#define FULL100 (1 << 14)
+#define HALF100 (1 << 13)
+#define FULL10 (1 << 12)
+#define HALF10 (1 << 11)
+#define ANDONE (1 << 5)
+#define LRFAULT (1 << 4)
+#define ANABLE (1 << 3)
+#define LLSTAT (1 << 2)
+#define EXTREGS (1 << 0)
+
+/* PHSTAT2 */
+#define PLRITY (1 << 4)
+
+/* PHSTAT3 */
+#define PHY3SPD100 (1 << 3)
+#define PHY3DPX (1 << 4)
+#define SPDDPX_SHIFT 2
+#define SPDDPX_MASK (0x7 << SPDDPX_SHIFT)
+
+/* PHANA */
+/* Default value for PHY initialization*/
+#define PHANA_DEFAULT 0x05E1
+
+/* PHANE */
+#define PDFLT (1 << 4)
+#define LPARCD (1 << 1)
+#define LPANABL (1 << 0)
+
+#define EUDAST_TEST_VAL 0x1234
+
+#define TSV_SIZE 7
+
+#define ENCX24J600_DEV_ID 0x1
+
+/* Configuration */
+
+/* Led is on when the link is present and driven low
+ * temporarily when packet is TX'd or RX'd
+ */
+#define LED_A_SETTINGS 0xC
+
+/* Led is on if the link is in 100 Mbps mode */
+#define LED_B_SETTINGS 0x8
+
+/* maximum ethernet frame length
+ * Currently not used as a limit anywhere
+ * (we're using the "huge frame enable" feature of
+ * enc424j600).
+ */
+#define MAX_FRAMELEN 1518
+
+/* Size in bytes of the receive buffer in enc424j600.
+ * Must be word aligned (even).
+ */
+#define RX_BUFFER_SIZE (15 * MAX_FRAMELEN)
+
+/* Start of the general purpose area in sram */
+#define SRAM_GP_START 0x0
+
+/* SRAM size */
+#define SRAM_SIZE 0x6000
+
+/* Start of the receive buffer */
+#define ERXST_VAL (SRAM_SIZE - RX_BUFFER_SIZE)
+
+#define RSV_RXLONGEVDROPEV 16
+#define RSV_CARRIEREV 18
+#define RSV_CRCERROR 20
+#define RSV_LENCHECKERR 21
+#define RSV_LENOUTOFRANGE 22
+#define RSV_RXOK 23
+#define RSV_RXMULTICAST 24
+#define RSV_RXBROADCAST 25
+#define RSV_DRIBBLENIBBLE 26
+#define RSV_RXCONTROLFRAME 27
+#define RSV_RXPAUSEFRAME 28
+#define RSV_RXUNKNOWNOPCODE 29
+#define RSV_RXTYPEVLAN 30
+
+#define RSV_RUNTFILTERMATCH 31
+#define RSV_NOTMEFILTERMATCH 32
+#define RSV_HASHFILTERMATCH 33
+#define RSV_MAGICPKTFILTERMATCH 34
+#define RSV_PTRNMTCHFILTERMATCH 35
+#define RSV_UNICASTFILTERMATCH 36
+
+#define RSV_SIZE 8
+#define RSV_BITMASK(x) (1 << ((x) - 16))
+#define RSV_GETBIT(x, y) (((x) & RSV_BITMASK(y)) ? 1 : 0)
+
+struct rsv {
+ u16 next_packet;
+ u16 len;
+ u32 rxstat;
+};
+
+/* Put RX buffer at 0 as suggested by the Errata datasheet */
+
+#define RXSTART_INIT ERXST_VAL
+#define RXEND_INIT 0x5FFF
+
+int regmap_encx24j600_spi_write(void *context, u8 reg, const u8 *data,
+ size_t count);
+int regmap_encx24j600_spi_read(void *context, u8 reg, u8 *data, size_t count);
+
+
+#endif
--
2.4.1
--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@...r.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
Powered by blists - more mailing lists