| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-id: <561BCD71.9020001@samsung.com>
Date: Mon, 12 Oct 2015 17:10:41 +0200
From: Jacek Anaszewski <j.anaszewski@...sung.com>
To: Ingi Kim <ingi2.kim@...sung.com>
Cc: robh+dt@...nel.org, pawel.moll@....com, mark.rutland@....com,
ijc+devicetree@...lion.org.uk, galak@...eaurora.org,
sameo@...ux.intel.com, lee.jones@...aro.org, rpurdie@...ys.net,
inki.dae@...sung.com, sw0312.kim@...sung.com,
beomho.seo@...sung.com, devicetree@...r.kernel.org,
linux-kernel@...r.kernel.org, linux-leds@...r.kernel.org
Subject: Re: [PATCH v2 3/3] leds: rt5033: Add RT5033 Flash led device driver
Hi Ingi,
Thanks for the update. Few comments below.
On 10/12/2015 03:12 PM, Ingi Kim wrote:
> This patch adds device driver of Richtek RT5033 PMIC.
> The driver supports a current regulated output to drive
> white LEDs for camera flash.
>
> Signed-off-by: Ingi Kim <ingi2.kim@...sung.com>
> ---
> drivers/leds/Kconfig | 8 ++
> drivers/leds/Makefile | 1 +
> drivers/leds/leds-rt5033.c | 223 +++++++++++++++++++++++++++++++++++++
> include/linux/mfd/rt5033-private.h | 49 ++++++++
> include/linux/mfd/rt5033.h | 22 +++-
> 5 files changed, 301 insertions(+), 2 deletions(-)
> create mode 100644 drivers/leds/leds-rt5033.c
>
> diff --git a/drivers/leds/Kconfig b/drivers/leds/Kconfig
> index 42990f2..29613e3 100644
> --- a/drivers/leds/Kconfig
> +++ b/drivers/leds/Kconfig
> @@ -345,6 +345,14 @@ config LEDS_PCA963X
> LED driver chip accessed via the I2C bus. Supported
> devices include PCA9633 and PCA9634
>
> +config LEDS_RT5033
> + tristate "LED support for RT5033 PMIC"
> + depends on LEDS_CLASS_FLASH && OF
> + depends on MFD_RT5033
> + help
> + This option enables support for on-chip LED driver on
> + RT5033 PMIC.
> +
> config LEDS_WM831X_STATUS
> tristate "LED support for status LEDs on WM831x PMICs"
> depends on LEDS_CLASS
> diff --git a/drivers/leds/Makefile b/drivers/leds/Makefile
> index b503f92..bcc4d93 100644
> --- a/drivers/leds/Makefile
> +++ b/drivers/leds/Makefile
> @@ -23,6 +23,7 @@ obj-$(CONFIG_LEDS_COBALT_QUBE) += leds-cobalt-qube.o
> obj-$(CONFIG_LEDS_COBALT_RAQ) += leds-cobalt-raq.o
> obj-$(CONFIG_LEDS_SUNFIRE) += leds-sunfire.o
> obj-$(CONFIG_LEDS_PCA9532) += leds-pca9532.o
> +obj-$(CONFIG_LEDS_RT5033) += leds-rt5033.o
> obj-$(CONFIG_LEDS_GPIO_REGISTER) += leds-gpio-register.o
> obj-$(CONFIG_LEDS_GPIO) += leds-gpio.o
> obj-$(CONFIG_LEDS_LP3944) += leds-lp3944.o
> diff --git a/drivers/leds/leds-rt5033.c b/drivers/leds/leds-rt5033.c
> new file mode 100644
> index 0000000..b470c94
> --- /dev/null
> +++ b/drivers/leds/leds-rt5033.c
> @@ -0,0 +1,223 @@
> +/*
> + * led driver for RT5033
> + *
> + * Copyright (C) 2015 Samsung Electronics, Co., Ltd.
> + * Ingi Kim <ingi2.kim@...sung.com>
> + *
> + * This program is free software; you can redistribute it and/or modify
> + * it under the terms of the GNU General Public License version 2 as
> + * published by the Free Software Foundation.
> + *
> + */
> +
> +#include <linux/mfd/rt5033.h>
> +#include <linux/mfd/rt5033-private.h>
> +#include <linux/module.h>
> +#include <linux/platform_device.h>
> +
> +#define RT5033_LED_FLASH_TIMEOUT_MIN 64000
> +#define RT5033_LED_FLASH_TIMEOUT_STEPS 32000
> +#define RT5033_LED_TORCH_CURRENT_LEVEL_MAX 16
> +
> +/* Macro for getting offset of flash timeout */
> +#define GET_TIMEOUT_OFFSET(tm, step) ((tm) / (step) - 2)
> +
> +static struct rt5033_led *flcdev_to_led(
> + struct led_classdev_flash *fled_cdev)
> +{
> + return container_of(fled_cdev, struct rt5033_led, fled_cdev);
> +}
> +
> +static int rt5033_led_brightness_set(struct led_classdev *led_cdev,
> + enum led_brightness brightness)
> +{
> + struct led_classdev_flash *fled_cdev = lcdev_to_flcdev(led_cdev);
> + struct rt5033_led *led = flcdev_to_led(fled_cdev);
I assume that you don't use mutex here deliberately?
> + if (!brightness) {
> + regmap_update_bits(led->regmap, RT5033_REG_FLED_FUNCTION2,
> + RT5033_FLED_CTRL2_MASK, 0x0);
> + } else {
> + regmap_update_bits(led->regmap, RT5033_REG_FLED_FUNCTION1,
> + RT5033_FLED_FUNC1_MASK, RT5033_FLED_PINCTRL);
> + regmap_update_bits(led->regmap, RT5033_REG_FLED_CTRL1,
> + RT5033_FLED_CTRL1_MASK,
> + (brightness - 1) << 4);
> + regmap_update_bits(led->regmap, RT5033_REG_FLED_FUNCTION2,
> + RT5033_FLED_CTRL2_MASK, RT5033_FLED_ENFLED);
> + }
> +
> + return 0;
> +}
> +
> +static void rt5033_init_flash_timeout(struct rt5033_led *led)
> +{
> + struct led_flash_setting *setting;
> +
> + setting = &led->fled_cdev.timeout;
> + setting->min = RT5033_LED_FLASH_TIMEOUT_MIN;
> + setting->max = led->data->flash_max_timeout;
> + setting->step = RT5033_LED_FLASH_TIMEOUT_STEPS;
> + setting->val = led->data->flash_max_timeout;
> +}
> +
> +static int rt5033_led_parse_dt(struct rt5033_led *led, struct device *dev)
> +{
> + struct device_node *np = dev->of_node;
> + struct device_node *child_node;
> + struct rt5033_led_config_data *data;
> + int ret = 0;
> +
> + if (!np)
> + return -ENXIO;
> +
> + data = devm_kzalloc(dev, sizeof(*data), GFP_KERNEL);
> + if (!data)
> + return -ENOMEM;
This way data will remain allocated until driver removal, whereas
you are using it only in rt5033_init_flash_timeout during driver
probing AFAICS. Please define local variable in rt5033_led_probe,
pass its pointer to this function and than pass the pointer to
rt5033_init_flash_timeout.
> + child_node = of_get_next_available_child(np, NULL);
> + if (!child_node) {
> + dev_err(dev, "DT child node isn't found\n");
> + return -EINVAL;
> + }
> +
> + led->fled_cdev.led_cdev.name =
> + of_get_property(child_node, "label", NULL) ? : child_node->name;
> +
> + ret = of_property_read_u32(child_node, "led-max-microamp",
> + &data->torch_max_microamp);
> + if (ret) {
> + dev_err(dev, "failed to parse led-max-microamp\n");
> + return ret;
> + }
data->torch_max_microamp isn't used anywhere, while it should be used
for initializing led_cdev->max_brightness.
> +
> + ret = of_property_read_u32(child_node, "flash-max-microamp",
> + &data->flash_max_microamp);
> + if (ret) {
> + dev_err(dev, "failed to parse flash-max-microamp\n");
> + return ret;
> + }
data->flash_max_microamp also isn't used anywhere. Does your device
support flash brightness setting? If yes then you should implement
also flash_brightness_set op. Otherwise this property is redundant.
> + ret = of_property_read_u32(child_node, "flash-max-timeout-us",
> + &data->flash_max_timeout);
> + if (ret)
> + dev_err(dev, "failed to parse flash-max-timeout-us\n");
> +
> + of_node_put(child_node);
> + led->data = data;
> +
> + return ret;
> +}
> +
> +static int rt5033_led_flash_timeout_set(struct led_classdev_flash *fled_cdev,
> + u32 timeout)
> +{
> + return 0;
> +}
> +
> +static int rt5033_led_flash_strobe_set(struct led_classdev_flash *fled_cdev,
> + bool state)
> +{
> + struct rt5033_led *led = flcdev_to_led(fled_cdev);
> + u32 flash_tm_reg;
I think that you need a mutex here and in rt5033_led_flash_strobe_set.
Otherwise following is possible:
Process 1:
rt5033_led_flash_strobe_set(led_cdev, 1);
regmap_update_bits(led->regmap, RT5033_REG_FLED_FUNCTION1,
RT5033_FLED_FUNC1_MASK, RT5033_FLED_RESET);
fled_cdev->led_cdev.brightness = LED_OFF;
Process 2:
led_set_brightness(led_cdev, 1);
fled_cdev->led_cdev.brightness = 1;
rt5033_led_brightness_set(led_cdev, LED_FULL);
regmap_update_bits(led->regmap, RT5033_REG_FLED_FUNCTION1,
RT5033_FLED_FUNC1_MASK, RT5033_FLED_PINCTRL);
regmap_update_bits(led->regmap, RT5033_REG_FLED_CTRL1,
RT5033_FLED_CTRL1_MASK,
(brightness - 1) << 4);
regmap_update_bits(led->regmap, RT5033_REG_FLED_FUNCTION2,
RT5033_FLED_CTRL2_MASK, RT5033_FLED_ENFLED);
Process 1:
regmap_update_bits(led->regmap, RT5033_REG_FLED_STROBE_CTRL2,
RT5033_FLED_STRBCTRL2_MASK, flash_tm_reg);
regmap_update_bits(led->regmap, RT5033_REG_FLED_FUNCTION1,
RT5033_FLED_FUNC1_MASK, RT5033_FLED_STRB_SEL
| RT5033_FLED_PINCTRL);
regmap_update_bits(led->regmap, RT5033_REG_FLED_FUNCTION2,
RT5033_FLED_FUNC2_MASK, RT5033_FLED_ENFLED
In a result LED class device will report brightness value 1,
whereas it would be inconsistent with hardware state, since
flash strobe turns torch mode off.
> +
> + regmap_update_bits(led->regmap, RT5033_REG_FLED_FUNCTION1,
> + RT5033_FLED_FUNC1_MASK, RT5033_FLED_RESET);
> + fled_cdev->led_cdev.brightness = LED_OFF;
> +
> + if (state) {
> + flash_tm_reg = GET_TIMEOUT_OFFSET(fled_cdev->timeout.val,
> + fled_cdev->timeout.step);
> + regmap_update_bits(led->regmap, RT5033_REG_FLED_STROBE_CTRL2,
> + RT5033_FLED_STRBCTRL2_MASK, flash_tm_reg);
> + regmap_update_bits(led->regmap, RT5033_REG_FLED_FUNCTION1,
> + RT5033_FLED_FUNC1_MASK, RT5033_FLED_STRB_SEL
> + | RT5033_FLED_PINCTRL);
> + regmap_update_bits(led->regmap, RT5033_REG_FLED_FUNCTION2,
> + RT5033_FLED_FUNC2_MASK, RT5033_FLED_ENFLED
> + | RT5033_FLED_SREG_STRB);
> + }
> +
> + return 0;
> +}
> +
> +static const struct led_flash_ops flash_ops = {
> + .strobe_set = rt5033_led_flash_strobe_set,
> + .timeout_set = rt5033_led_flash_timeout_set,
> +};
> +
> +static int rt5033_led_probe(struct platform_device *pdev)
> +{
> + struct rt5033_dev *rt5033 = dev_get_drvdata(pdev->dev.parent);
> + struct rt5033_led *led;
> + struct led_classdev *led_cdev;
> + int ret;
> +
> + led = devm_kzalloc(&pdev->dev, sizeof(*led), GFP_KERNEL);
> + if (!led)
> + return -ENOMEM;
> +
> + platform_set_drvdata(pdev, led);
> + led->dev = &pdev->dev;
> + led->regmap = rt5033->regmap;
> +
> + ret = rt5033_led_parse_dt(led, &pdev->dev);
> + if (ret)
> + return ret;
> +
> + rt5033_init_flash_timeout(led);
> + led->fled_cdev.ops = &flash_ops;
> + led_cdev = &led->fled_cdev.led_cdev;
> +
> + led_cdev->max_brightness = RT5033_LED_TORCH_CURRENT_LEVEL_MAX;
This should depend on led-max-microamp.
> + led_cdev->brightness_set_sync = rt5033_led_brightness_set;
> + led_cdev->flags |= LED_CORE_SUSPENDRESUME | LED_DEV_CAP_FLASH;
You need also a work queue since your ops can sleep.
> +
> + ret = led_classdev_flash_register(&pdev->dev, &led->fled_cdev);
> + if (ret < 0) {
> + dev_err(&pdev->dev, "can't register LED %s\n", led_cdev->name);
> + return ret;
> + }
> +
> + regmap_update_bits(led->regmap, RT5033_REG_FLED_FUNCTION1,
> + RT5033_FLED_FUNC1_MASK, RT5033_FLED_RESET);
> +
> + return 0;
> +}
> +
> +static int rt5033_led_remove(struct platform_device *pdev)
> +{
> + struct rt5033_led *led = platform_get_drvdata(pdev);
> +
> + led_classdev_flash_unregister(&led->fled_cdev);
> +
> + return 0;
> +}
> +
> +static const struct platform_device_id rt5033_led_id[] = {
> + { "rt5033-led", },
> + { /* sentinel */ },
> +};
> +MODULE_DEVICE_TABLE(platform, rt5033_led_id);
> +
> +static const struct of_device_id rt5033_led_match[] = {
> + { .compatible = "richtek,rt5033-led", },
> + { /* sentinel */ },
> +};
> +MODULE_DEVICE_TABLE(of, rt5033_led_match);
> +
> +static struct platform_driver rt5033_led_driver = {
> + .driver = {
> + .name = "rt5033-led",
> + .of_match_table = rt5033_led_match,
> + },
> + .probe = rt5033_led_probe,
> + .id_table = rt5033_led_id,
> + .remove = rt5033_led_remove,
> +};
> +module_platform_driver(rt5033_led_driver);
> +
> +MODULE_AUTHOR("Ingi Kim <ingi2.kim@...sung.com>");
> +MODULE_DESCRIPTION("Richtek RT5033 LED driver");
> +MODULE_LICENSE("GPL v2");
> +MODULE_ALIAS("platform:rt5033-led");
> diff --git a/include/linux/mfd/rt5033-private.h b/include/linux/mfd/rt5033-private.h
> index 1b63fc2..c8e99e4 100644
> --- a/include/linux/mfd/rt5033-private.h
> +++ b/include/linux/mfd/rt5033-private.h
> @@ -93,6 +93,55 @@ enum rt5033_reg {
> #define RT5033_RT_CTRL1_UUG_MASK 0x02
> #define RT5033_RT_HZ_MASK 0x01
>
> +/* RT5033 FLED Function1 register */
> +#define RT5033_FLED_FUNC1_MASK 0x94
> +#define RT5033_FLED_STRB_SEL 0x04
> +#define RT5033_FLED_PINCTRL 0x10
> +#define RT5033_FLED_RESET 0x80
> +
> +/* RT5033 FLED Function2 register */
> +#define RT5033_FLED_FUNC2_MASK 0x81
> +#define RT5033_FLED_ENFLED 0x01
> +#define RT5033_FLED_SREG_STRB 0x80
> +
> +/* RT5033 FLED Strobe Control1 */
> +#define RT5033_FLED_STRBCTRL1_MASK 0xFF
> +#define RT5033_FLED_STRBCTRL1_TM_CUR_MAX 0xE0
> +#define RT5033_FLED_STRBCTRL1_FL_CUR_DEF 0x0D
> +#define RT5033_FLED_STRBCTRL1_FL_CUR_MAX 0x1F
> +
> +/* RT5033 FLED Strobe Control2 */
> +#define RT5033_FLED_STRBCTRL2_MASK 0x3F
> +#define RT5033_FLED_STRBCTRL2_TM_DEF 0x0F
> +#define RT5033_FLED_STRBCTRL2_TM_MAX 0x3F
> +
> +/* RT5033 FLED Control1 */
> +#define RT5033_FLED_CTRL1_MASK 0xF7
> +#define RT5033_FLED_CTRL1_TORCH_CUR_DEF 0x20
> +#define RT5033_FLED_CTRL1_TORCH_CUR_MAX 0xF0
> +#define RT5033_FLED_CTRL1_LBP_DEF 0x02
> +#define RT5033_FLED_CTRL1_LBP_MAX 0x07
> +
> +/* RT5033 FLED Control2 */
> +#define RT5033_FLED_CTRL2_MASK 0xFF
> +#define RT5033_FLED_CTRL2_VMID_DEF 0x37
> +#define RT5033_FLED_CTRL2_VMID_MAX 0x3F
> +#define RT5033_FLED_CTRL2_TRACK_ALIVE 0x40
> +#define RT5033_FLED_CTRL2_MID_TRACK 0x80
> +
> +/* RT5033 FLED Control4 */
> +#define RT5033_FLED_CTRL4_MASK 0xE0
> +#define RT5033_FLED_CTRL4_RESV 0x14
> +#define RT5033_FLED_CTRL4_VTRREG_DEF 0x40
> +#define RT5033_FLED_CTRL4_VTRREG_MAX 0x60
> +#define RT5033_FLED_CTRL4_TRACK_CLK 0x80
> +
> +/* RT5033 FLED Control5 */
> +#define RT5033_FLED_CTRL5_MASK 0xC0
> +#define RT5033_FLED_CTRL5_RESV 0x10
> +#define RT5033_FLED_CTRL5_TA_GOOD 0x40
> +#define RT5033_FLED_CTRL5_TA_EXIST 0x80
> +
> /* RT5033 control register */
> #define RT5033_CTRL_FCCM_BUCK_MASK 0x00
> #define RT5033_CTRL_BUCKOMS_MASK 0x01
> diff --git a/include/linux/mfd/rt5033.h b/include/linux/mfd/rt5033.h
> index 6cff5cf..6374d84 100644
> --- a/include/linux/mfd/rt5033.h
> +++ b/include/linux/mfd/rt5033.h
> @@ -12,10 +12,11 @@
> #ifndef __RT5033_H__
> #define __RT5033_H__
>
> -#include <linux/regulator/consumer.h>
> #include <linux/i2c.h>
> -#include <linux/regmap.h>
> +#include <linux/led-class-flash.h>
> #include <linux/power_supply.h>
> +#include <linux/regmap.h>
> +#include <linux/regulator/consumer.h>
>
> /* RT5033 regulator IDs */
> enum rt5033_regulators {
> @@ -59,4 +60,21 @@ struct rt5033_charger {
> struct rt5033_charger_data *chg;
> };
>
> +/* RT5033 Flash led platform data */
> +struct rt5033_led_config_data {
> + u32 torch_max_microamp;
> + u32 flash_max_microamp;
> + u32 flash_max_timeout;
> + enum led_brightness max_brightness;
> +};
> +
> +struct rt5033_led {
> + struct device *dev;
> + struct rt5033_dev *rt5033;
> + struct regmap *regmap;
> +
> + struct led_classdev_flash fled_cdev;
> + struct rt5033_led_config_data *data;
It is not needed to have config data here.
> +};
> +
> #endif /* __RT5033_H__ */
>
--
Best Regards,
Jacek Anaszewski
--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@...r.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
Powered by blists - more mailing lists