| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-ID: <1445014753-15450-4-git-send-email-afd@ti.com>
Date: Fri, 16 Oct 2015 11:59:12 -0500
From: "Andrew F. Davis" <afd@...com>
To: Rob Herring <robh+dt@...nel.org>, Pawel Moll <pawel.moll@....com>,
Mark Rutland <mark.rutland@....com>,
Ian Campbell <ijc+devicetree@...lion.org.uk>,
Kumar Gala <galak@...eaurora.org>,
Lee Jones <lee.jones@...aro.org>,
Mark Brown <broonie@...nel.org>,
Alexandre Courbot <gnurou@...il.com>,
Grygorii Strashko <grygorii.strashko@...com>
CC: <linux-gpio@...r.kernel.org>, <devicetree@...r.kernel.org>,
<linux-kernel@...r.kernel.org>, "Andrew F. Davis" <afd@...com>
Subject: [PATCH 3/4] regulator: tps65086: Add regulator driver for the TPS65086 PMIC
Add support for TPS65086 PMIC regulators.
The regulators set consists of 3 Step-down Controllers, 3 Step-down
Converters, 3 LDOs, 3 Load Switches, and a Sink and Source LDO. The
output voltages are configurable and are meant to supply power to a
SoC and/or other components.
Signed-off-by: Andrew F. Davis <afd@...com>
---
drivers/regulator/Kconfig | 7 +
drivers/regulator/Makefile | 1 +
drivers/regulator/tps65086-regulator.c | 263 +++++++++++++++++++++++++++++++++
3 files changed, 271 insertions(+)
create mode 100644 drivers/regulator/tps65086-regulator.c
diff --git a/drivers/regulator/Kconfig b/drivers/regulator/Kconfig
index 64bccff..cb5f04d 100644
--- a/drivers/regulator/Kconfig
+++ b/drivers/regulator/Kconfig
@@ -680,6 +680,13 @@ config REGULATOR_TPS6507X
three step-down converters and two general-purpose LDO voltage regulators.
It supports TI's software based Class-2 SmartReflex implementation.
+config REGULATOR_TPS65086
+ tristate "TI TPS65086 Power regulator"
+ depends on MFD_TPS65086
+ help
+ This driver provides support for the voltage regulators on the
+ TI TPS65086 PMIC.
+
config REGULATOR_TPS65090
tristate "TI TPS65090 Power regulator"
depends on MFD_TPS65090
diff --git a/drivers/regulator/Makefile b/drivers/regulator/Makefile
index 0f81749..945d8ec 100644
--- a/drivers/regulator/Makefile
+++ b/drivers/regulator/Makefile
@@ -85,6 +85,7 @@ obj-$(CONFIG_REGULATOR_TPS6105X) += tps6105x-regulator.o
obj-$(CONFIG_REGULATOR_TPS62360) += tps62360-regulator.o
obj-$(CONFIG_REGULATOR_TPS65023) += tps65023-regulator.o
obj-$(CONFIG_REGULATOR_TPS6507X) += tps6507x-regulator.o
+obj-$(CONFIG_REGULATOR_TPS65086) += tps65086-regulator.o
obj-$(CONFIG_REGULATOR_TPS65090) += tps65090-regulator.o
obj-$(CONFIG_REGULATOR_TPS65217) += tps65217-regulator.o
obj-$(CONFIG_REGULATOR_TPS65218) += tps65218-regulator.o
diff --git a/drivers/regulator/tps65086-regulator.c b/drivers/regulator/tps65086-regulator.c
new file mode 100644
index 0000000..5fd6cf4
--- /dev/null
+++ b/drivers/regulator/tps65086-regulator.c
@@ -0,0 +1,263 @@
+/*
+ * Regulator driver for TPS65086x PMIC
+ *
+ * Copyright (C) 2015 Texas Instruments Incorporated - http://www.ti.com/
+ *
+ * Author: Andrew F. Davis <afd@...com>
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ * This program is distributed "as is" WITHOUT ANY WARRANTY of any
+ * kind, whether expressed or implied; without even the implied warranty
+ * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License version 2 for more details.
+ *
+ * Based on the TPS65912 driver
+ */
+
+#include <linux/module.h>
+#include <linux/of_device.h>
+#include <linux/platform_device.h>
+#include <linux/regulator/driver.h>
+#include <linux/regulator/of_regulator.h>
+
+#include <linux/mfd/tps65086.h>
+
+enum tps65086_regulators { BUCK1, BUCK2, BUCK3, BUCK4, BUCK5, BUCK6, LDOA1,
+ LDOA2, LDOA3, SWA1, SWB1, SWB2, VTT };
+
+#define TPS65086_REGULATOR(_name, _id, _nv, _vr, _vm, _er, _em, _lr, _dr, _dm)\
+ [_id] = { \
+ .desc = { \
+ .name = _name, \
+ .id = _id, \
+ .ops = ®_ops, \
+ .n_voltages = _nv, \
+ .type = REGULATOR_VOLTAGE, \
+ .owner = THIS_MODULE, \
+ .vsel_reg = _vr, \
+ .vsel_mask = _vm, \
+ .enable_reg = _er, \
+ .enable_mask = _em, \
+ .volt_table = NULL, \
+ .linear_ranges = _lr, \
+ .n_linear_ranges = ARRAY_SIZE(_lr), \
+ }, \
+ .decay_reg = _dr, \
+ .decay_mask = _dm, \
+ }
+
+#define TPS65086_SWITCH(_name, _id, _er, _em) \
+ [_id] = { \
+ .desc = { \
+ .name = _name, \
+ .id = _id, \
+ .ops = &switch_ops, \
+ .type = REGULATOR_VOLTAGE, \
+ .owner = THIS_MODULE, \
+ .enable_reg = _er, \
+ .enable_mask = _em, \
+ }, \
+ }
+
+struct tps65086_regulator {
+ struct regulator_desc desc;
+ unsigned int decay_reg;
+ unsigned int decay_mask;
+};
+
+static const struct regulator_linear_range tps65086_buck126_10mv_ranges[] = {
+ REGULATOR_LINEAR_RANGE(0, 0x0, 0x0, 0),
+ REGULATOR_LINEAR_RANGE(410000, 0x1, 0x7F, 10000),
+};
+
+static const struct regulator_linear_range tps65086_buck126_25mv_ranges[] = {
+ REGULATOR_LINEAR_RANGE(0, 0x0, 0x0, 0),
+ REGULATOR_LINEAR_RANGE(1000000, 0x1, 0x18, 0),
+ REGULATOR_LINEAR_RANGE(1025000, 0x19, 0x7F, 25000),
+};
+
+static const struct regulator_linear_range tps65086_buck345_ranges[] = {
+ REGULATOR_LINEAR_RANGE(0, 0x0, 0x0, 0),
+ REGULATOR_LINEAR_RANGE(425000, 0x1, 0x7F, 25000),
+};
+
+static const struct regulator_linear_range tps65086_ldoa1_ranges[] = {
+ REGULATOR_LINEAR_RANGE(1350000, 0x0, 0x0, 0),
+ REGULATOR_LINEAR_RANGE(1500000, 0x1, 0x7, 100000),
+ REGULATOR_LINEAR_RANGE(2300000, 0x8, 0xA, 100000),
+ REGULATOR_LINEAR_RANGE(2700000, 0xB, 0xD, 150000),
+ REGULATOR_LINEAR_RANGE(3300000, 0xE, 0xE, 0),
+};
+
+static const struct regulator_linear_range tps65086_ldoa23_ranges[] = {
+ REGULATOR_LINEAR_RANGE(700000, 0x0, 0xD, 50000),
+ REGULATOR_LINEAR_RANGE(1400000, 0xE, 0xF, 100000),
+};
+
+/* Operations permitted on regulators */
+static struct regulator_ops reg_ops = {
+ .enable = regulator_enable_regmap,
+ .disable = regulator_disable_regmap,
+ .is_enabled = regulator_is_enabled_regmap,
+ .set_voltage_sel = regulator_set_voltage_sel_regmap,
+ .map_voltage = regulator_map_voltage_linear_range,
+ .get_voltage_sel = regulator_get_voltage_sel_regmap,
+ .list_voltage = regulator_list_voltage_linear_range,
+};
+
+/* Operations permitted on load switches */
+static struct regulator_ops switch_ops = {
+ .enable = regulator_enable_regmap,
+ .disable = regulator_disable_regmap,
+ .is_enabled = regulator_is_enabled_regmap,
+};
+
+static struct tps65086_regulator regulators[] = {
+ TPS65086_REGULATOR("BUCK1", BUCK1, 0x80, TPS65086_BUCK1CTRL,
+ BUCK_VID_MASK, TPS65086_BUCK123CTRL, BIT(0),
+ tps65086_buck126_10mv_ranges, TPS65086_BUCK1CTRL,
+ BIT(0)),
+ TPS65086_REGULATOR("BUCK2", BUCK2, 0x80, TPS65086_BUCK2CTRL,
+ BUCK_VID_MASK, TPS65086_BUCK123CTRL, BIT(1),
+ tps65086_buck126_10mv_ranges, TPS65086_BUCK2CTRL,
+ BIT(0)),
+ TPS65086_REGULATOR("BUCK3", BUCK3, 0x80, TPS65086_BUCK3VID,
+ BUCK_VID_MASK, TPS65086_BUCK123CTRL, BIT(2),
+ tps65086_buck345_ranges, TPS65086_BUCK3DECAY,
+ BIT(0)),
+ TPS65086_REGULATOR("BUCK4", BUCK4, 0x80, TPS65086_BUCK4VID,
+ BUCK_VID_MASK, TPS65086_BUCK4CTRL, BIT(0),
+ tps65086_buck345_ranges, TPS65086_BUCK4VID,
+ BIT(0)),
+ TPS65086_REGULATOR("BUCK5", BUCK5, 0x80, TPS65086_BUCK5VID,
+ BUCK_VID_MASK, TPS65086_BUCK5CTRL, BIT(0),
+ tps65086_buck345_ranges, TPS65086_BUCK5CTRL,
+ BIT(0)),
+ TPS65086_REGULATOR("BUCK6", BUCK6, 0x80, TPS65086_BUCK6VID,
+ BUCK_VID_MASK, TPS65086_BUCK6CTRL, BIT(0),
+ tps65086_buck126_10mv_ranges, TPS65086_BUCK6CTRL,
+ BIT(0)),
+ TPS65086_REGULATOR("LDOA1", LDOA1, 0xF, TPS65086_LDOA1CTRL,
+ VDOA1_VID_MASK, TPS65086_LDOA1CTRL, BIT(0),
+ tps65086_ldoa1_ranges, 0, 0),
+ TPS65086_REGULATOR("LDOA2", LDOA2, 0x10, TPS65086_LDOA2VID,
+ VDOA23_VID_MASK, TPS65086_LDOA2CTRL, BIT(0),
+ tps65086_ldoa23_ranges, 0, 0),
+ TPS65086_REGULATOR("LDOA3", LDOA3, 0x10, TPS65086_LDOA3VID,
+ VDOA23_VID_MASK, TPS65086_LDOA3CTRL, BIT(0),
+ tps65086_ldoa23_ranges, 0, 0),
+ TPS65086_SWITCH("SWA1", SWA1, TPS65086_SWVTT_EN, BIT(5)),
+ TPS65086_SWITCH("SWB1", SWB1, TPS65086_SWVTT_EN, BIT(6)),
+ TPS65086_SWITCH("SWB2", SWB2, TPS65086_SWVTT_EN, BIT(7)),
+ TPS65086_SWITCH("VTT", VTT, TPS65086_SWVTT_EN, BIT(4)),
+};
+
+static struct of_regulator_match tps65086_matches[] = {
+ { .name = "buck1", .driver_data = ®ulators[BUCK1], },
+ { .name = "buck2", .driver_data = ®ulators[BUCK2], },
+ { .name = "buck3", .driver_data = ®ulators[BUCK3], },
+ { .name = "buck4", .driver_data = ®ulators[BUCK4], },
+ { .name = "buck5", .driver_data = ®ulators[BUCK5], },
+ { .name = "buck6", .driver_data = ®ulators[BUCK6], },
+ { .name = "ldoa1", .driver_data = ®ulators[LDOA1], },
+ { .name = "ldoa2", .driver_data = ®ulators[LDOA2], },
+ { .name = "ldoa3", .driver_data = ®ulators[LDOA3], },
+ { .name = "swa1", .driver_data = ®ulators[SWA1], },
+ { .name = "swb1", .driver_data = ®ulators[SWB1], },
+ { .name = "swb2", .driver_data = ®ulators[SWB2], },
+ { .name = "vtt", .driver_data = ®ulators[VTT], },
+};
+
+static inline bool has_25mv_mode(int id)
+{
+ switch (id) {
+ case BUCK1:
+ case BUCK2:
+ case BUCK6:
+ return true;
+ default:
+ return false;
+ }
+}
+
+static int tps65086_regulator_probe(struct platform_device *pdev)
+{
+ struct tps65086 *tps = dev_get_drvdata(pdev->dev.parent);
+ struct regulator_config config = { };
+ struct regulator_dev *rdev;
+ struct tps65086_regulator *regulator;
+
+ int i, ret;
+
+ platform_set_drvdata(pdev, tps);
+
+ config.dev = &pdev->dev;
+ config.driver_data = tps;
+ config.regmap = tps->regmap;
+
+ ret = of_regulator_match(&pdev->dev, pdev->dev.of_node,
+ tps65086_matches,
+ ARRAY_SIZE(tps65086_matches));
+ if (ret < 0) {
+ dev_err(tps->dev, "Error parsing regulator init data\n");
+ return ret;
+ }
+
+ for (i = 0; i < ARRAY_SIZE(tps65086_matches); i++) {
+ config.init_data = tps65086_matches[i].init_data;
+ config.of_node = tps65086_matches[i].of_node;
+ regulator = tps65086_matches[i].driver_data;
+
+ /* Check for 25mV step mode */
+ if (has_25mv_mode(regulator->desc.id) &&
+ of_property_read_bool(config.of_node, "ti,regulator-step-size-25mv")) {
+ regulator->desc.linear_ranges = tps65086_buck126_25mv_ranges;
+ regulator->desc.n_linear_ranges = ARRAY_SIZE(tps65086_buck126_25mv_ranges);
+ }
+
+ /* Check for decay mode */
+ if (i <= BUCK6 && of_property_read_bool(config.of_node, "ti,regulator-decay")) {
+ ret = regmap_write_bits(tps->regmap,
+ regulator->decay_reg,
+ regulator->decay_mask,
+ regulator->decay_mask);
+ if (ret < 0) {
+ dev_err(tps->dev, "Error setting decay\n");
+ return ret;
+ }
+ }
+
+ rdev = devm_regulator_register(&pdev->dev, ®ulator->desc,
+ &config);
+ if (IS_ERR(rdev)) {
+ dev_err(tps->dev, "failed to register %s regulator\n",
+ pdev->name);
+ return PTR_ERR(rdev);
+ }
+ }
+
+ return 0;
+}
+
+static const struct of_device_id tps65086_regulator_of_match_table[] = {
+ { .compatible = "ti,tps65086-regulator", },
+ { /* sentinel */ },
+};
+MODULE_DEVICE_TABLE(of, tps65086_regulator_of_match_table);
+
+static struct platform_driver tps65086_regulator_driver = {
+ .driver = {
+ .name = "tps65086-pmic",
+ .of_match_table = tps65086_regulator_of_match_table,
+ },
+ .probe = tps65086_regulator_probe,
+};
+
+module_platform_driver(tps65086_regulator_driver);
+
+MODULE_AUTHOR("Andrew F. Davis <afd@...com>");
+MODULE_DESCRIPTION("TPS65086x voltage regulator driver");
+MODULE_LICENSE("GPL v2");
--
1.9.1
--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@...r.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
Powered by blists - more mailing lists