lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
Open Source and information security mailing list archives
| ||
|
Date: Fri, 06 Nov 2015 09:03:16 +0900 From: Krzysztof Kozlowski <k.kozlowski@...sung.com> To: Pavel Fedin <p.fedin@...sung.com>, devicetree@...r.kernel.org, linux-arm-kernel@...ts.infradead.org, linux-samsung-soc@...r.kernel.org, linux-kernel@...r.kernel.org Cc: Rob Herring <robh+dt@...nel.org>, Pawel Moll <pawel.moll@....com>, Mark Rutland <mark.rutland@....com>, Ian Campbell <ijc+devicetree@...lion.org.uk>, Kumar Gala <galak@...eaurora.org>, Kukjin Kim <kgene@...nel.org> Subject: Re: [PATCH v6 1/4] Documentation: dt-bindings: Describe SROMc configuration On 05.11.2015 21:03, Pavel Fedin wrote: > Add documentation for new subnode properties, allowing bank configuration. > Based on u-boot implementation, but heavily reworked. > > Also, fix size of SROMc mapping in the example. > > Signed-off-by: Pavel Fedin <p.fedin@...sung.com> > --- > .../bindings/arm/samsung/exynos-srom.txt | 71 +++++++++++++++++++++- > 1 file changed, 69 insertions(+), 2 deletions(-) > > diff --git a/Documentation/devicetree/bindings/arm/samsung/exynos-srom.txt b/Documentation/devicetree/bindings/arm/samsung/exynos-srom.txt > index 33886d5..cce5c1f 100644 > --- a/Documentation/devicetree/bindings/arm/samsung/exynos-srom.txt > +++ b/Documentation/devicetree/bindings/arm/samsung/exynos-srom.txt > @@ -5,8 +5,75 @@ Required properties: > > - reg: offset and length of the register set > > -Example: > +Optional properties: > +The SROM controller can be used to attach external peripherals. In this case > +extra properties, describing the bus behind it, should be specified as below: > + > +- #address-cells: Must be set to 2 to allow memory address translation > + > +- #size-cells: Must be set to 1 to allow CS address passing > + > +- ranges: Must be set up to reflect the memory layout with four integer values > + per bank: > + <bank-number> 0 <physical address of bank> <size> > + > +Sub-nodes: > +The actual device nodes should be added as subnodes to the SROMc node. These > +subnodes, except regular device specification, should contain the following > +properties, describing configuration of the relevant SROM bank: > + > +Required properties: > +- reg: bank number, base address (relative to start of the bank) and size of > + the memory mapped for the device. Note that base address will be > + typically 0 as this is the start of the bank. > + > +- samsung,srom-timing : array of 6 integers, specifying bank timings in the > + following order: Tacp, Tcah, Tcoh, Tacc, Tcos, Tacs. > + Each value is specified in cycles and has the following > + meaning and valid range: > + Tacp : Page mode access cycle at Page mode (0 - 15) > + Tcah : Address holding time after CSn (0 - 15) > + Tcoh : Chip selection hold on OEn (0 - 15) > + Tacc : Access cycle (0 - 32) All of the manuals have error here. Probably it can be either: 1-32 or 0-31. I would bet on 0-31, what do you think? Rest looks good: Reviewed-by: Krzysztof Kozlowski <k.kozlowski@...sung.com> Best regards, Krzysztof -- To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to majordomo@...r.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html Please read the FAQ at http://www.tux.org/lkml/
Powered by blists - more mailing lists