linux-kernel - RE: [PATCH 2/2] can: m_can: Add CAN clock generated by UPLLCK support

lists.openwall.net		lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC
Open Source and information security mailing list archives

Hash Suite: Windows password security audit tool. GUI, reports in PDF.

[<prev] [next>] [<thread-prev] [thread-next>] [day] [month] [year] [list]

Message-ID: <B256D81BAE5131468A838E5D7A243641D636B712@penmbx01>
Date:	Thu, 19 Nov 2015 04:24:59 +0000
From:	"Yang, Wenyou" <Wenyou.Yang@...el.com>
To:	Marc Kleine-Budde <mkl@...gutronix.de>,
	Wolfgang Grandegger <wg@...ndegger.com>
CC:	"linux-can@...r.kernel.org" <linux-can@...r.kernel.org>,
	"netdev@...r.kernel.org" <netdev@...r.kernel.org>,
	"linux-kernel@...r.kernel.org" <linux-kernel@...r.kernel.org>,
	"Ferre, Nicolas" <Nicolas.FERRE@...el.com>
Subject: RE: [PATCH 2/2] can: m_can: Add CAN clock generated by UPLLCK
 support

Hi Marc,

> -----Original Message-----
> From: Marc Kleine-Budde [mailto:mkl@...gutronix.de]
> Sent: 2015年11月18日 18:23
> To: Yang, Wenyou; Wolfgang Grandegger
> Cc: linux-can@...r.kernel.org; netdev@...r.kernel.org; linux-
> kernel@...r.kernel.org; Ferre, Nicolas
> Subject: Re: [PATCH 2/2] can: m_can: Add CAN clock generated by UPLLCK
> support
> 
> On 11/18/2015 11:04 AM, Wenyou Yang wrote:
> > As said SAMA5D2 datasheet, it is recommended to use the CAN clock at
> > frequencies of 20, 40 or 80 MHz. To achieve these frequencies, PMC
> > GCK3 must select the UPLLCK(480 MHz) as source clock and divide by 24,
> > 12 or 6. In this patch the CAN clock at 20 MHz.
> >
> > As it is configured through DT, it doesn't affect the M_CAN without
> > configuring CAN clock and its generated clock.
> >
> > Signed-off-by: Wenyou Yang <wenyou.yang@...el.com>
> 
> NACK
> 
> Please do this setup in your SoC code, where you setup the clock infrastructure or
> have a look at Documentation/devicetree/bindings/clock/clock-bindings.txt
> "Assigned clock parents and rates"
Thank you for your advice. I will do this setup via DT.


> 
> > ---
> >
> >  drivers/net/can/m_can/m_can.c |   16 +++++++++++++++-
> >  1 file changed, 15 insertions(+), 1 deletion(-)
> >
> > diff --git a/drivers/net/can/m_can/m_can.c
> > b/drivers/net/can/m_can/m_can.c index fd1caa0..2ca47db 100644
> > --- a/drivers/net/can/m_can/m_can.c
> > +++ b/drivers/net/can/m_can/m_can.c
> > @@ -269,6 +269,8 @@ enum m_can_mram_cfg {
> >  #define TX_BUF_XTD		BIT(30)
> >  #define TX_BUF_RTR		BIT(29)
> >
> > +#define AT91_CAN_CLK_FREQ	20000000
> > +
> >  /* address offset and element number for each FIFO/Buffer in the
> > Message RAM */  struct mram_cfg {
> >  	u16 off;
> > @@ -1188,7 +1190,7 @@ static int m_can_plat_probe(struct platform_device
> *pdev)
> >  	struct m_can_priv *priv;
> >  	struct resource *res;
> >  	void __iomem *addr;
> > -	struct clk *hclk, *cclk;
> > +	struct clk *hclk, *cclk, *upll_clk;
> >  	int irq, ret;
> >
> >  	hclk = devm_clk_get(&pdev->dev, "hclk"); @@ -1198,6 +1200,18 @@
> > static int m_can_plat_probe(struct platform_device *pdev)
> >  		return -ENODEV;
> >  	}
> >
> > +	upll_clk = devm_clk_get(&pdev->dev, "upllclk");
> > +	if (!IS_ERR(upll_clk)) {
> > +		ret = clk_set_parent(cclk, upll_clk);
> > +		if (!ret) {
> > +			ret = clk_set_rate(cclk, AT91_CAN_CLK_FREQ);
> > +			if (ret) {
> > +				dev_err(&pdev->dev, "failed to set gck\n");
> > +				return -ENODEV;
> > +			}
> > +		}
> > +	}
> > +
> >  	res = platform_get_resource_byname(pdev, IORESOURCE_MEM,
> "m_can");
> >  	addr = devm_ioremap_resource(&pdev->dev, res);
> >  	irq = platform_get_irq_byname(pdev, "int0");
> >
> 
> regards,
> Marc
> 
> --
> Pengutronix e.K.                  | Marc Kleine-Budde           |
> Industrial Linux Solutions        | Phone: +49-231-2826-924     |
> Vertretung West/Dortmund          | Fax:   +49-5121-206917-5555 |
> Amtsgericht Hildesheim, HRA 2686  | http://www.pengutronix.de   |


Best Regards,
Wenyou Yang