Message-ID: <201511190104.tAJ148g3035290@krsrvapps-01.diasemi.com>
Date:	Thu, 19 Nov 2015 09:59:15 +0900
From:	James Ban <James.Ban.opensource@...semi.com>
To:	LINUXKERNEL <linux-kernel@...r.kernel.org>,
	Liam Girdwood <lgirdwood@...il.com>,
	Mark Brown <broonie@...nel.org>
CC:	David Dajun Chen <david.chen@...semi.com>,
	Support Opensource <support.opensource@...semi.com>
Subject: [PATCH V2] regulator: pv88060: new regulator driver


From: James Ban <James.Ban.opensource@...semi.com>

This is the driver for the Powerventure PV88060 BUCKs and LDOs regulator.
It communicates via an I2C bus to the device.

Signed-off-by: James Ban <James.Ban.opensource@...semi.com>

---
Changes since PATCH V1
- Removed parsing the DT manually.
- Removed setting the constraints in driver.
- Removed printing an error after parsing dt.

This patch applies against linux-next and next-20151115 


 .../devicetree/bindings/regulator/pv88060.txt      |  124 ++++++
 drivers/regulator/Kconfig                          |    8 +
 drivers/regulator/Makefile                         |    1 +
 drivers/regulator/pv88060-regulator.c              |  437 ++++++++++++++++++++
 drivers/regulator/pv88060-regulator.h              |   69 ++++
 5 files changed, 639 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/regulator/pv88060.txt
 create mode 100644 drivers/regulator/pv88060-regulator.c
 create mode 100644 drivers/regulator/pv88060-regulator.h

diff --git a/Documentation/devicetree/bindings/regulator/pv88060.txt b/Documentation/devicetree/bindings/regulator/pv88060.txt
new file mode 100644
index 0000000..10a6dad
--- /dev/null
+++ b/Documentation/devicetree/bindings/regulator/pv88060.txt
@@ -0,0 +1,124 @@
+* Powerventure Semiconductor PV88060 Voltage Regulator
+
+Required properties:
+- compatible: "pvs,pv88060".
+- reg: I2C slave address, usually 0x49.
+- interrupts: the interrupt outputs of the controller
+- regulators: A node that houses a sub-node for each regulator within the
+  device. Each sub-node is identified using the node's name, with valid
+  values listed below. The content of each sub-node is defined by the
+  standard binding for regulators; see regulator.txt.
+  BUCK1, LDO1, LDO2, LDO3, LDO4, LDO5, LDO6, LDO7, SW1, SW2, SW3, SW4,
+  SW5, and SW6.
+
+Optional properties:
+- Any optional property defined in regulator.txt
+
+Example
+
+	pmic: pv88060@49 {
+		compatible = "pvs,pv88060";
+		reg = <0x49>;
+		interrupt-parent = <&gpio>;
+		interrupts = <24 24>;
+
+		regulators {
+			BUCK1 {
+				regulator-name = "buck1";
+				regulator-min-microvolt = <2800000>;
+				regulator-max-microvolt = <4387500>;
+				regulator-min-microamp 	= <1496000>;
+				regulator-max-microamp 	= <4189000>;
+				regulator-boot-on;
+			};
+
+			LDO1 {
+				regulator-name = "ldo1";
+				regulator-min-microvolt = <1200000>;
+				regulator-max-microvolt = <3350000>;
+				regulator-boot-on;
+			};
+
+			LDO2 {
+				regulator-name = "ldo2";
+				regulator-min-microvolt = <1200000>;
+				regulator-max-microvolt = <3350000>;
+				regulator-boot-on;
+			};
+
+			LDO3 {
+				regulator-name = "ldo3";
+				regulator-min-microvolt = <1200000>;
+				regulator-max-microvolt = <3350000>;
+				regulator-boot-on;
+			};
+
+			LDO4 {
+				regulator-name = "ldo4";
+				regulator-min-microvolt = <1200000>;
+				regulator-max-microvolt = <3350000>;
+				regulator-boot-on;
+			};
+
+			LDO5 {
+				regulator-name = "ldo5";
+				regulator-min-microvolt = <1200000>;
+				regulator-max-microvolt = <3350000>;
+				regulator-boot-on;
+			};
+
+			LDO6 {
+				regulator-name = "ldo6";
+				regulator-min-microvolt = <1200000>;
+				regulator-max-microvolt = <3350000>;
+				regulator-boot-on;
+			};
+
+			LDO7 {
+				regulator-name = "ldo7";
+				regulator-min-microvolt = <1200000>;
+				regulator-max-microvolt = <3350000>;
+				regulator-boot-on;
+			};
+
+			SW1 {
+				regulator-name = "sw1";
+				regulator-min-microvolt = <5000000>;
+				regulator-max-microvolt = <5000000>;
+			};
+
+			SW2 {
+				regulator-name = "sw2";
+				regulator-min-microvolt = <5000000>;
+				regulator-max-microvolt = <5000000>;
+				regulator-boot-on;
+			};
+
+			SW3 {
+				regulator-name = "sw3";
+				regulator-min-microvolt = <5000000>;
+				regulator-max-microvolt = <5000000>;
+				regulator-boot-on;
+			};
+
+			SW4 {
+				regulator-name = "sw4";
+				regulator-min-microvolt = <5000000>;
+				regulator-max-microvolt = <5000000>;
+				regulator-boot-on;
+			};
+
+			SW5 {
+				regulator-name = "sw5";
+				regulator-min-microvolt = <5000000>;
+				regulator-max-microvolt = <5000000>;
+				regulator-boot-on;
+			};
+
+			SW6 {
+				regulator-name = "sw6";
+				regulator-min-microvolt = <5000000>;
+				regulator-max-microvolt = <5000000>;
+			};
+		};
+	};
\ No newline at end of file
diff --git a/drivers/regulator/Kconfig b/drivers/regulator/Kconfig
index 8df0b0e..c61f72f 100644
--- a/drivers/regulator/Kconfig
+++ b/drivers/regulator/Kconfig
@@ -504,6 +504,14 @@ config REGULATOR_PFUZE100
 	  Say y here to support the regulators found on the Freescale
 	  PFUZE100/PFUZE200 PMIC.
 
+config REGULATOR_PV88060
+	tristate "Powerventure Semiconductor PV88060 regulator"
+	depends on I2C
+	select REGMAP_I2C
+	help
+	  Say y here to support the voltage regulators and convertors
+	  PV88060
+
 config REGULATOR_PWM
 	tristate "PWM voltage regulator"
 	depends on PWM
diff --git a/drivers/regulator/Makefile b/drivers/regulator/Makefile
index 0f81749..b11c8a4 100644
--- a/drivers/regulator/Makefile
+++ b/drivers/regulator/Makefile
@@ -66,6 +66,7 @@ obj-$(CONFIG_REGULATOR_QCOM_SMD_RPM) += qcom_smd-regulator.o
 obj-$(CONFIG_REGULATOR_QCOM_SPMI) += qcom_spmi-regulator.o
 obj-$(CONFIG_REGULATOR_PALMAS) += palmas-regulator.o
 obj-$(CONFIG_REGULATOR_PFUZE100) += pfuze100-regulator.o
+obj-$(CONFIG_REGULATOR_PV88060) += pv88060-regulator.o
 obj-$(CONFIG_REGULATOR_PWM) += pwm-regulator.o
 obj-$(CONFIG_REGULATOR_TPS51632) += tps51632-regulator.o
 obj-$(CONFIG_REGULATOR_PBIAS) += pbias-regulator.o
diff --git a/drivers/regulator/pv88060-regulator.c b/drivers/regulator/pv88060-regulator.c
new file mode 100644
index 0000000..60b16d8
--- /dev/null
+++ b/drivers/regulator/pv88060-regulator.c
@@ -0,0 +1,437 @@
+/*
+ * pv88060-regulator.c - Regulator device driver for PV88060
+ * Copyright (C) 2015  Powerventure Semiconductor Ltd.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * as published by the Free Software Foundation; either version 2
+ * of the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ */
+
+#include <linux/err.h>
+#include <linux/gpio.h>
+#include <linux/i2c.h>
+#include <linux/module.h>
+#include <linux/init.h>
+#include <linux/slab.h>
+#include <linux/regulator/driver.h>
+#include <linux/regulator/machine.h>
+#include <linux/regmap.h>
+#include <linux/irq.h>
+#include <linux/interrupt.h>
+#include <linux/regulator/of_regulator.h>
+#include <linux/proc_fs.h>
+#include <linux/uaccess.h>
+#include "pv88060-regulator.h"
+
+#define PV88060_MAX_REGULATORS	14
+
+/* PV88060 REGULATOR IDs */
+enum {
+	/* BUCKs */
+	PV88060_ID_BUCK1,
+
+	/* LDOs */
+	PV88060_ID_LDO1,
+	PV88060_ID_LDO2,
+	PV88060_ID_LDO3,
+	PV88060_ID_LDO4,
+	PV88060_ID_LDO5,
+	PV88060_ID_LDO6,
+	PV88060_ID_LDO7,
+
+	/* SWTs */
+	PV88060_ID_SW1,
+	PV88060_ID_SW2,
+	PV88060_ID_SW3,
+	PV88060_ID_SW4,
+	PV88060_ID_SW5,
+	PV88060_ID_SW6,
+};
+
+struct pv88060_regulator {
+	struct regulator_desc desc;
+	/* Current limiting */
+	unsigned	n_current_limits;
+	const int	*current_limits;
+	unsigned int limit_mask;
+	unsigned int conf;		/* buck configuration register */
+};
+
+struct pv88060 {
+	struct device *dev;
+	struct regmap *regmap;
+	struct regulator_dev *rdev[PV88060_MAX_REGULATORS];
+};
+
+static const struct regmap_config pv88060_regmap_config = {
+	.reg_bits = 8,
+	.val_bits = 8,
+};
+
+/* Current limits array (in uA) for BUCK1
+ * Entry indexes corresponds to register values.
+ */
+
+static const int pv88060_buck1_limits[] = {
+	1496000, 2393000, 3291000, 4189000
+};
+
+static unsigned int pv88060_buck_get_mode(struct regulator_dev *rdev)
+{
+	struct pv88060_regulator *info = rdev_get_drvdata(rdev);
+	unsigned int data;
+	int ret, mode = 0;
+
+	ret = regmap_read(rdev->regmap, info->conf, &data);
+	if (ret < 0)
+		return ret;
+
+	switch (data & PV88060_BUCK_MODE_MASK) {
+	case PV88060_BUCK_MODE_SYNC:
+		mode = REGULATOR_MODE_FAST;
+		break;
+	case PV88060_BUCK_MODE_AUTO:
+		mode = REGULATOR_MODE_NORMAL;
+		break;
+	case PV88060_BUCK_MODE_SLEEP:
+		mode = REGULATOR_MODE_STANDBY;
+		break;
+	}
+
+	return mode;
+}
+
+static int pv88060_buck_set_mode(struct regulator_dev *rdev,
+					unsigned int mode)
+{
+	struct pv88060_regulator *info = rdev_get_drvdata(rdev);
+	int val = 0;
+
+	switch (mode) {
+	case REGULATOR_MODE_FAST:
+		val = PV88060_BUCK_MODE_SYNC;
+		break;
+	case REGULATOR_MODE_NORMAL:
+		val = PV88060_BUCK_MODE_AUTO;
+		break;
+	case REGULATOR_MODE_STANDBY:
+		val = PV88060_BUCK_MODE_SLEEP;
+		break;
+	default:
+		return -EINVAL;
+	}
+
+	return regmap_update_bits(rdev->regmap, info->conf,
+					PV88060_BUCK_MODE_MASK, val);
+}
+
+static int pv88060_set_current_limit(struct regulator_dev *rdev, int min,
+				    int max)
+{
+	struct pv88060_regulator *info = rdev_get_drvdata(rdev);
+	int i;
+
+	/* search for closest to maximum */
+	for (i = info->n_current_limits; i >= 0; i--) {
+		if (min <= info->current_limits[i]
+			&& max >= info->current_limits[i]) {
+			return regmap_update_bits(rdev->regmap,
+				info->conf,
+				info->limit_mask,
+				i << PV88060_BUCK_ILIM_SHIFT);
+		}
+	}
+
+	return -EINVAL;
+}
+
+static int pv88060_get_current_limit(struct regulator_dev *rdev)
+{
+	struct pv88060_regulator *info = rdev_get_drvdata(rdev);
+	unsigned int data;
+	int ret;
+
+	ret = regmap_read(rdev->regmap, info->conf, &data);
+	if (ret < 0)
+		return ret;
+
+	data = (data & info->limit_mask) >> PV88060_BUCK_ILIM_SHIFT;
+	return info->current_limits[data];
+}
+
+static struct regulator_ops pv88060_buck_ops = {
+	.get_mode = pv88060_buck_get_mode,
+	.set_mode = pv88060_buck_set_mode,
+	.enable = regulator_enable_regmap,
+	.disable = regulator_disable_regmap,
+	.is_enabled = regulator_is_enabled_regmap,
+	.set_voltage_sel = regulator_set_voltage_sel_regmap,
+	.get_voltage_sel = regulator_get_voltage_sel_regmap,
+	.list_voltage = regulator_list_voltage_linear,
+	.set_current_limit = pv88060_set_current_limit,
+	.get_current_limit = pv88060_get_current_limit,
+};
+
+static struct regulator_ops pv88060_ldo_ops = {
+	.enable = regulator_enable_regmap,
+	.disable = regulator_disable_regmap,
+	.is_enabled = regulator_is_enabled_regmap,
+	.set_voltage_sel = regulator_set_voltage_sel_regmap,
+	.get_voltage_sel = regulator_get_voltage_sel_regmap,
+	.list_voltage = regulator_list_voltage_linear,
+};
+
+#define PV88060_BUCK(chip, regl_name, min, step, max, limits_array) \
+{\
+	.desc	=	{\
+		.id = chip##_ID_##regl_name,\
+		.name = __stringify(chip##_##regl_name),\
+		.of_match = of_match_ptr(#regl_name),\
+		.regulators_node = of_match_ptr("regulators"),\
+		.type = REGULATOR_VOLTAGE,\
+		.owner = THIS_MODULE,\
+		.ops = &pv88060_buck_ops,\
+		.min_uV = min,\
+		.uV_step = step,\
+		.n_voltages = ((max) - (min))/(step) + 1,\
+		.enable_reg = PV88060_REG_##regl_name##_CONF0,\
+		.enable_mask = PV88060_BUCK_EN, \
+		.vsel_reg = PV88060_REG_##regl_name##_CONF0,\
+		.vsel_mask = PV88060_VBUCK_MASK,\
+	},\
+	.current_limits = limits_array,\
+	.n_current_limits = ARRAY_SIZE(limits_array),\
+	.limit_mask = PV88060_BUCK_ILIM_MASK, \
+	.conf = PV88060_REG_##regl_name##_CONF1,\
+}
+
+#define PV88060_LDO(chip, regl_name, min, step, max) \
+{\
+	.desc	=	{\
+		.id = chip##_ID_##regl_name,\
+		.name = __stringify(chip##_##regl_name),\
+		.of_match = of_match_ptr(#regl_name),\
+		.regulators_node = of_match_ptr("regulators"),\
+		.type = REGULATOR_VOLTAGE,\
+		.owner = THIS_MODULE,\
+		.ops = &pv88060_ldo_ops,\
+		.min_uV = min, \
+		.uV_step = step, \
+		.n_voltages = (step) ? ((max - min) / step + 1) : 1, \
+		.enable_reg = PV88060_REG_##regl_name##_CONF, \
+		.enable_mask = PV88060_LDO_EN, \
+		.vsel_reg = PV88060_REG_##regl_name##_CONF, \
+		.vsel_mask = PV88060_VLDO_MASK, \
+	},\
+}
+
+#define PV88060_SW(chip, regl_name, max) \
+{\
+	.desc	=	{\
+		.id = chip##_ID_##regl_name,\
+		.name = __stringify(chip##_##regl_name),\
+		.of_match = of_match_ptr(#regl_name),\
+		.regulators_node = of_match_ptr("regulators"),\
+		.type = REGULATOR_VOLTAGE,\
+		.owner = THIS_MODULE,\
+		.ops = &pv88060_ldo_ops,\
+		.min_uV = max,\
+		.uV_step = 0,\
+		.n_voltages = 1,\
+		.enable_reg = PV88060_REG_##regl_name##_CONF,\
+		.enable_mask = PV88060_SW_EN,\
+	},\
+}
+
+static const struct pv88060_regulator pv88060_regulator_info[] = {
+	PV88060_BUCK(PV88060, BUCK1, 2800000, 12500, 4387500,
+		pv88060_buck1_limits),
+	PV88060_LDO(PV88060, LDO1, 1200000, 50000, 3350000),
+	PV88060_LDO(PV88060, LDO2, 1200000, 50000, 3350000),
+	PV88060_LDO(PV88060, LDO3, 1200000, 50000, 3350000),
+	PV88060_LDO(PV88060, LDO4, 1200000, 50000, 3350000),
+	PV88060_LDO(PV88060, LDO5, 1200000, 50000, 3350000),
+	PV88060_LDO(PV88060, LDO6, 1200000, 50000, 3350000),
+	PV88060_LDO(PV88060, LDO7, 1200000, 50000, 3350000),
+	PV88060_SW(PV88060, SW1, 5000000),
+	PV88060_SW(PV88060, SW2, 5000000),
+	PV88060_SW(PV88060, SW3, 5000000),
+	PV88060_SW(PV88060, SW4, 5000000),
+	PV88060_SW(PV88060, SW5, 5000000),
+	PV88060_SW(PV88060, SW6, 5000000),
+};
+
+static irqreturn_t pv88060_irq_handler(int irq, void *data)
+{
+	struct pv88060 *chip = data;
+	int i, reg_val, err, ret = IRQ_NONE;
+
+	err = regmap_read(chip->regmap, PV88060_REG_EVENT_A, &reg_val);
+	if (err < 0)
+		goto error_i2c;
+
+	if (reg_val & PV88060_E_VDD_FLT) {
+		for (i = 0; i < PV88060_MAX_REGULATORS; i++) {
+			if (chip->rdev[i] != NULL) {
+				regulator_notifier_call_chain(chip->rdev[i],
+					REGULATOR_EVENT_UNDER_VOLTAGE,
+					NULL);
+			}
+		}
+
+		err = regmap_update_bits(chip->regmap, PV88060_REG_EVENT_A,
+			PV88060_E_VDD_FLT, PV88060_E_VDD_FLT);
+		if (err < 0)
+			goto error_i2c;
+
+		ret = IRQ_HANDLED;
+	}
+
+	if (reg_val & PV88060_E_OVER_TEMP) {
+		for (i = 0; i < PV88060_MAX_REGULATORS; i++) {
+			if (chip->rdev[i] != NULL) {
+				regulator_notifier_call_chain(chip->rdev[i],
+					REGULATOR_EVENT_OVER_TEMP,
+					NULL);
+			}
+		}
+
+		err = regmap_update_bits(chip->regmap, PV88060_REG_EVENT_A,
+			PV88060_E_OVER_TEMP, PV88060_E_OVER_TEMP);
+		if (err < 0)
+			goto error_i2c;
+
+		ret = IRQ_HANDLED;
+	}
+
+	return ret;
+
+error_i2c:
+	dev_err(chip->dev, "I2C error : %d\n", err);
+	return IRQ_NONE;
+}
+
+/*
+ * I2C driver interface functions
+ */
+static int pv88060_i2c_probe(struct i2c_client *i2c,
+		const struct i2c_device_id *id)
+{
+	struct regulator_init_data *init_data = dev_get_platdata(&i2c->dev);
+	struct pv88060 *chip;
+	struct regulator_config config = { };
+	int error, i, ret = 0;
+
+	chip = devm_kzalloc(&i2c->dev, sizeof(struct pv88060), GFP_KERNEL);
+	if (!chip)
+		return -ENOMEM;
+
+	chip->dev = &i2c->dev;
+	chip->regmap = devm_regmap_init_i2c(i2c, &pv88060_regmap_config);
+	if (IS_ERR(chip->regmap)) {
+		error = PTR_ERR(chip->regmap);
+		dev_err(chip->dev, "Failed to allocate register map: %d\n",
+			error);
+		return error;
+	}
+
+	i2c_set_clientdata(i2c, chip);
+
+	if (i2c->irq != 0) {
+		ret = regmap_write(chip->regmap, PV88060_REG_MASK_A, 0xFF);
+		if (ret < 0) {
+			dev_err(chip->dev,
+				"Failed to mask A reg: %d\n", ret);
+			return ret;
+		}
+
+		regmap_write(chip->regmap, PV88060_REG_MASK_B, 0xFF);
+		if (ret < 0) {
+			dev_err(chip->dev,
+				"Failed to mask B reg: %d\n", ret);
+			return ret;
+		}
+
+		regmap_write(chip->regmap, PV88060_REG_MASK_C, 0xFF);
+		if (ret < 0) {
+			dev_err(chip->dev,
+				"Failed to mask C reg: %d\n", ret);
+			return ret;
+		}
+
+		ret = request_threaded_irq(i2c->irq, NULL,
+					pv88060_irq_handler,
+					IRQF_TRIGGER_LOW|IRQF_ONESHOT,
+					"pv88060", chip);
+		if (ret != 0) {
+			dev_err(chip->dev, "Failed to request IRQ: %d\n",
+				i2c->irq);
+			return ret;
+		}
+
+		ret = regmap_update_bits(chip->regmap, PV88060_REG_MASK_A,
+			PV88060_M_VDD_FLT | PV88060_M_OVER_TEMP, 0);
+		if (ret < 0) {
+			dev_err(chip->dev,
+				"Failed to update mask reg: %d\n", ret);
+			return ret;
+		}
+
+	} else {
+		dev_warn(chip->dev, "No IRQ configured\n");
+	}
+
+	config.dev = chip->dev;
+	config.regmap = chip->regmap;
+
+	for (i = 0; i < PV88060_MAX_REGULATORS; i++) {
+		if (init_data)
+			config.init_data = &init_data[i];
+
+		config.driver_data = (void *)&pv88060_regulator_info[i];
+		chip->rdev[i] = devm_regulator_register(chip->dev,
+			&pv88060_regulator_info[i].desc, &config);
+		if (IS_ERR(chip->rdev[i])) {
+			dev_err(chip->dev,
+				"Failed to register PV88060 regulator\n");
+			return PTR_ERR(chip->rdev[i]);
+		}
+	}
+
+	return 0;
+}
+
+static const struct i2c_device_id pv88060_i2c_id[] = {
+	{"pv88060", 0},
+	{},
+};
+MODULE_DEVICE_TABLE(i2c, pv88060_i2c_id);
+
+#ifdef CONFIG_OF
+static const struct of_device_id pv88060_dt_ids[] = {
+	{ .compatible = "pvs,pv88060", .data = &pv88060_i2c_id[0] },
+	{},
+};
+MODULE_DEVICE_TABLE(of, pv88060_dt_ids);
+#endif
+
+static struct i2c_driver pv88060_regulator_driver = {
+	.driver = {
+		.name = "pv88060",
+		.of_match_table = of_match_ptr(pv88060_dt_ids),
+	},
+	.probe = pv88060_i2c_probe,
+	.id_table = pv88060_i2c_id,
+};
+
+module_i2c_driver(pv88060_regulator_driver);
+
+MODULE_AUTHOR("James Ban <James.Ban.opensource@...semi.com>");
+MODULE_DESCRIPTION("Regulator device driver for Powerventure PV88060");
+MODULE_LICENSE("GPL");
diff --git a/drivers/regulator/pv88060-regulator.h b/drivers/regulator/pv88060-regulator.h
new file mode 100644
index 0000000..02ca920
--- /dev/null
+++ b/drivers/regulator/pv88060-regulator.h
@@ -0,0 +1,69 @@
+/*
+ * pv88060-regulator.h - Regulator definitions for PV88060
+ * Copyright (C) 2015 Powerventure Semiconductor Ltd.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * as published by the Free Software Foundation; either version 2
+ * of the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ */
+
+#ifndef __PV88060_REGISTERS_H__
+#define __PV88060_REGISTERS_H__
+
+/* System Control and Event Registers */
+#define	PV88060_REG_EVENT_A			0x04
+#define	PV88060_REG_MASK_A			0x08
+#define	PV88060_REG_MASK_B			0x09
+#define	PV88060_REG_MASK_C			0x0A
+
+/* Regulator Registers */
+#define	PV88060_REG_BUCK1_CONF0			0x1B
+#define	PV88060_REG_BUCK1_CONF1			0x1C
+#define	PV88060_REG_LDO1_CONF			0x1D
+#define	PV88060_REG_LDO2_CONF			0x1E
+#define	PV88060_REG_LDO3_CONF			0x1F
+#define	PV88060_REG_LDO4_CONF			0x20
+#define	PV88060_REG_LDO5_CONF			0x21
+#define	PV88060_REG_LDO6_CONF			0x22
+#define	PV88060_REG_LDO7_CONF			0x23
+
+#define	PV88060_REG_SW1_CONF			0x3B
+#define	PV88060_REG_SW2_CONF			0x3C
+#define	PV88060_REG_SW3_CONF			0x3D
+#define	PV88060_REG_SW4_CONF			0x3E
+#define	PV88060_REG_SW5_CONF			0x3F
+#define	PV88060_REG_SW6_CONF			0x40
+
+/* PV88060_REG_EVENT_A (addr=0x04) */
+#define	PV88060_E_VDD_FLT			0x01
+#define	PV88060_E_OVER_TEMP			0x02
+
+/* PV88060_REG_MASK_A (addr=0x08) */
+#define	PV88060_M_VDD_FLT			0x01
+#define	PV88060_M_OVER_TEMP			0x02
+
+/* PV88060_REG_BUCK1_CONF0 (addr=0x1B) */
+#define	PV88060_BUCK_EN			0x80
+#define PV88060_VBUCK_MASK			0x7F
+/* PV88060_REG_LDO1/2/3/4/5/6/7_CONT */
+#define	PV88060_LDO_EN			0x40
+#define PV88060_VLDO_MASK			0x3F
+/* PV88060_REG_SW1/2/3/4/5_CONF */
+#define	PV88060_SW_EN			0x80
+
+/* PV88060_REG_BUCK1_CONF1 (addr=0x1C) */
+#define	PV88060_BUCK_ILIM_SHIFT			2
+#define	PV88060_BUCK_ILIM_MASK			0x0C
+#define	PV88060_BUCK_MODE_SHIFT			0
+#define	PV88060_BUCK_MODE_MASK			0x03
+#define	PV88060_BUCK_MODE_SLEEP			0x00
+#define	PV88060_BUCK_MODE_AUTO			0x01
+#define	PV88060_BUCK_MODE_SYNC			0x02
+
+#endif	/* __PV88060_REGISTERS_H__ */
-- 
end-of-patch for PATCH V2

--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@...r.kernel.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html
Please read the FAQ at  http://www.tux.org/lkml/

Powered by blists - more mailing lists