| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-Id: <201511220007.35517.linux@rainbow-software.org>
Date: Sun, 22 Nov 2015 00:07:12 +0100
From: Ondrej Zary <linux@...nbow-software.org>
To: Finn Thain <fthain@...egraphics.com.au>
Cc: Sam Creasey <sammy@...my.net>,
Michael Schmitz <schmitzmic@...il.com>,
"James E.J. Bottomley" <JBottomley@...n.com>,
linux-m68k@...r.kernel.org, linux-scsi@...r.kernel.org,
linux-kernel@...r.kernel.org
Subject: Re: [PATCH 00/71] More fixes, cleanup and modernization for NCR5380 drivers
On Saturday 21 November 2015 14:01:39 Ondrej Zary wrote:
> On Saturday 21 November 2015 02:58:57 Finn Thain wrote:
> >
> > Hi Ondrej,
> >
> > On Fri, 20 Nov 2015, Ondrej Zary wrote:
> >
> > > On Friday 20 November 2015 02:41:19 Finn Thain wrote:
> > > >
> > > >
> > > > My tests involved 3 different scsi targets (two disks and a CD-ROM)
> > > > but none of these send a SDTR. Your log says the driver correctly
> > > > rejected the SDTR message but that doesn't mean the target actually
> > > > went to MSG IN phase and got the message. Do you have any older
> > > > targets you can test?
> > >
[...]
> > >
> >
> > Thanks for these test results! It looks like READ(10) commands don't work.
> > I don't know the cause of the failures but it appears to be an old bug.
> > Did you find any regression?
> >
> > I gather that your setup here is a QUANTUM LP240S target with Domex 3181
> > (DTC-436) card and g_NCR5380 module. I've been testing a similar setup:
> > QUANTUM LPS540S target with a Domex 3191D (DTC-536) card and dmx3191d
> > module. In both setups PIO is used exclusively, no IRQ is used, and
> > FLAG_DTC3181E is set. I didn't see any issues in my tests, so your results
> > are surprising.
>
> I agree that the results are surprising. Even tried 2.4 kernels (Debian 3.1)
> and even 2.2 (Debian 3.0) and nothing worked.
> HW is fine - the drive is accessible in Windows 98 (with Domex driver
> installed).
>
> Now testing the Canon FG2-5202 controller - a simple 8-bit ISA card with only
> two chips: NCR 53C400 and 74LS245. It's memory mapped, IRQ hardwired to 7.
>
> # modprobe g_NCR5380_mmio ncr_irq=255 ncr_addr=0xd8000 ncr_53c400=1
>
> [ 1245.919223] scsi2 : interrupts not enabled. for better interactive performance,
> [ 1245.919326] scsi2 : please jumper the board for a free IRQ.
> [ 1245.919389] scsi host2: Generic NCR5380/NCR53C400 SCSI, io_port 0x0, n_io_port 0, base 0xd8000, irq 0, can_queue 16, cmd_per_lun 2, sg_tablesize 128, this_id 7, flags { NCR53C400 }, USLEEP_POLL 3, USLEEP_WAITLONG 1250, options { AUTOPROBE_IRQ PSEUDO_DMA NCR53C400 }
> [ 1246.376738] scsi 2:0:1:0: Direct-Access QUANTUM LP240S GM240S01X 4.6 PQ: 0 ANSI: 2 CCS
> [ 1248.202198] sd 2:0:1:0: Attached scsi generic sg1 type 0
> [ 1248.420856] 53C400r: no 53C80 gated irq after transfer
> [ 1248.420948] 53C400r: no end dma signal
> [ 1248.422459] sd 2:0:1:0: [sdb] Sector size 0 reported, assuming 512.
>
> Seems that the PSEUDO_DMA is broken. After adding FLAG_NO_PSEUDO_DMA:
>
> # modprobe g_NCR5380_mmio ncr_irq=255 ncr_addr=0xd8000 ncr_53c400=1
>
> [ 67.974362] scsi2 : interrupts not enabled. for better interactive performance,
> [ 67.974463] scsi2 : please jumper the board for a free IRQ.
> [ 67.974526] scsi host2: Generic NCR5380/NCR53C400 SCSI, io_port 0x0, n_io_port 0, base 0xd8000, irq 0, can_queue 16, cmd_per_lun 2, sg_tablesize 128, this_id 7, flags { NCR53C400 NO_PSEUDO_DMA }, USLEEP_POLL 3, USLEEP_WAITLONG 1250, options { AUTOPROBE_IRQ PSEUDO_DMA NCR53C400 }
> [ 68.432728] scsi 2:0:1:0: Direct-Access QUANTUM LP240S GM240S01X 4.6 PQ: 0 ANSI: 2 CCS
> [ 70.258258] sd 2:0:1:0: Attached scsi generic sg1 type 0
> [ 70.277265] sd 2:0:1:0: [sdb] 479350 512-byte logical blocks: (245 MB/234 MiB)
> [ 70.482252] sd 2:0:1:0: [sdb] Write Protect is off
> [ 70.482335] sd 2:0:1:0: [sdb] Mode Sense: 8b 00 00 08
> [ 70.889646] sd 2:0:1:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
> [ 73.159513] sdb: sdb1
> [ 74.617099] sd 2:0:1:0: [sdb] Attached SCSI disk
>
> Yeah, first success! I can even mount the filesystem, although it takes ages
> (a minute) and these messages:
> [ 160.872074] sd 2:0:1:0: [sdb] aborting command
> [ 161.816083] sd 2:0:1:0: [sdb] aborting command
>
> # hdparm -t --direct /dev/sdb
>
> /dev/sdb:
> [ 244.840075] sd 2:0:1:0: [sdb] aborting command
> [ 248.824078] sd 2:0:1:0: [sdb] aborting command
> [ 293.864069] sd 2:0:1:0: [sdb] aborting command
> [ 297.824075] sd 2:0:1:0: [sdb] aborting command
> [ 319.765020] blk_update_request: critical target error, dev sdb, sector 0
> [ 319.972994] blk_update_request: critical target error, dev sdb, sector 0
> Timing O_DIRECT disk reads: 2 MB in 105.26 seconds = 19.46 kB/sec
>
>
>
> With your patches (and adding FLAG_NO_PSEUDO_DMA), modprobe is slower but
> mount faster (4 seconds) and then works better:
>
> # modprobe g_NCR5380_mmio ncr_irq=255 ncr_addr=0xd8000 ncr_53c400=1
>
> [ 130.126185] scsi2 : interrupts not enabled. for better interactive performance,
> [ 130.126284] scsi2 : please jumper the board for a free IRQ.
> [ 130.126347] scsi host2: Generic NCR5380/NCR53C400 SCSI, io_port 0x0, n_io_port 0, base 0xd8000, irq 0, can_queue 16, cmd_per_lun 2, sg_tablesize 128, this_id 7, flags { NO_PSEUDO_DMA }, options { AUTOPROBE_IRQ PSEUDO_DMA }
> [ 145.221755] scsi 2:0:1:0: Direct-Access QUANTUM LP240S GM240S01X 4.6 PQ: 0 ANSI: 2 CCS
> [ 220.629912] sd 2:0:1:0: Attached scsi generic sg1 type 0
> [ 220.651400] sd 2:0:1:0: [sdb] 479350 512-byte logical blocks: (245 MB/234 MiB)
> [ 220.654061] sd 2:0:1:0: [sdb] Write Protect is off
> [ 220.659344] sd 2:0:1:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
> [ 220.732415] sdb: sdb1
> [ 220.749760] sd 2:0:1:0: [sdb] Attached SCSI disk
>
> # hdparm -t --direct /dev/sdb
>
> /dev/sdb:
> Timing O_DIRECT disk reads: 2 MB in 18.25 seconds = 112.20 kB/sec
>
>
>
> IRQ seems to work too, although driver always shows "irq 0":
>
> # modprobe g_NCR5380_mmio ncr_irq=7 ncr_addr=0xd8000 ncr_53c400=1
>
> [ 117.263062] scsi host2: Generic NCR5380/NCR53C400 SCSI, io_port 0x0, n_io_port 0, base 0xd8000, irq 0, can_queue 16, cmd_per_lun 2, sg_tablesize 128, this_id 7, flags { NO_PSEUDO_DMA }, options { AUTOPROBE_IRQ PSEUDO_DMA }
> [ 132.357474] scsi 2:0:1:0: Direct-Access QUANTUM LP240S GM240S01X 4.6 PQ: 0 ANSI: 2 CCS
> [ 207.765080] sd 2:0:1:0: Attached scsi generic sg1 type 0
> [ 207.783415] sd 2:0:1:0: [sdb] 479350 512-byte logical blocks: (245 MB/234 MiB)
> [ 207.786167] sd 2:0:1:0: [sdb] Write Protect is off
> [ 207.790260] sd 2:0:1:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
> [ 207.859669] sdb: sdb1
> [ 207.876556] sd 2:0:1:0: [sdb] Attached SCSI disk
>
> # hdparm -t --direct /dev/sdb
>
> /dev/sdb:
> Timing O_DIRECT disk reads: 2 MB in 18.30 seconds = 111.94 kB/sec
>
> # mount /dev/sdb1 /mnt
> # umount /mnt
> # head /proc/interrupts
> CPU0
> 0: 44793 XT-PIC timer
> 1: 9 XT-PIC i8042
> 2: 0 XT-PIC cascade
> 7: 86 XT-PIC NCR5380
> 8: 1 XT-PIC rtc0
> 9: 0 XT-PIC uhci_hcd:usb1, uhci_hcd:usb2
> 10: 1179 XT-PIC eth0
> 12: 136 XT-PIC i8042
> 14: 3411 XT-PIC pata_via
>
Even the HP C2502 (that never worked) works now. It's 8-bit card based on
NCR 53C400A (there are also 74ALS245 and 3 PALCE chips).
Configuration is by using magic numbers, wrote a simple userspace enabler:
#include <stdio.h>
#include <sys/io.h>
const unsigned short io_ports[] = { 0x280, 0x290, 0x300, 0x310, 0x330, 0x340, 0x348, 0x350 };
/* IRQs: 2,3,4,5,7 */
void configure_hp400a(int idx, unsigned char irq) {
unsigned char b = 0;
outb(0x0f, 0x779);
outb(0x22, 0x379);
outb(0xf0, 0x379);
outb(0x20, 0x379);
outb(0x80, 0x379);
if (irq != 2 && irq != 3 && irq != 4 && irq != 5 && irq != 7)
irq = 0;
if (idx >= 0 && idx <= 7)
b = 0x80 | idx | (irq << 4);
outb(b, 0x379);
}
int main(void) {
if (iopl(3)) {
perror("iopl");
return 1;
}
configure_hp400a(0, 7);
return 0;
}
And now:
# modprobe g_NCR5380 ncr_irq=255 ncr_addr=0x280 ncr_53c400a=1
[ 79.051669] scsi2 : interrupts not enabled. for better interactive performance,
[ 79.051770] scsi2 : please jumper the board for a free IRQ.
[ 79.051833] scsi host2: Generic NCR5380/NCR53C400 SCSI, io_port 0x280, n_io_port 16, base 0x0, irq 0, can_queue 16, cmd_per_lun 2, sg_tablesize 128, this_id 7, flags { NO_PSEUDO_DMA }, options { AUTOPROBE_IRQ PSEUDO_DMA }
[ 95.390329] scsi 2:0:1:0: Direct-Access QUANTUM LP240S GM240S01X 4.6 PQ: 0 ANSI: 2 CCS
[ 177.022776] sd 2:0:1:0: Attached scsi generic sg1 type 0
[ 177.041505] sd 2:0:1:0: [sdb] 479350 512-byte logical blocks: (245 MB/234 MiB)
[ 177.044491] sd 2:0:1:0: [sdb] Write Protect is off
[ 177.049605] sd 2:0:1:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 177.129093] sdb: sdb1
[ 177.145439] sd 2:0:1:0: [sdb] Attached SCSI disk
# hdparm -t --direct /dev/sdb
/dev/sdb:
Timing O_DIRECT disk reads: 2 MB in 21.38 seconds = 95.77 kB/sec
Seems to work without IRQ.
With IRQ is enabled, no interrupts are shown in /proc/interrupts.
--
Ondrej Zary
--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@...r.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
Powered by blists - more mailing lists