linux-kernel - [PATCH v2 4/8] drm/rockchip: Optimization vop mode set

lists.openwall.net		lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC
Open Source and information security mailing list archives

Hash Suite: Windows password security audit tool. GUI, reports in PDF.

[<prev] [next>] [<thread-prev] [thread-next>] [day] [month] [year] [list]

Message-Id: <1450081931-9709-5-git-send-email-mark.yao@rock-chips.com>
Date:	Mon, 14 Dec 2015 16:32:07 +0800
From:	Mark Yao <mark.yao@...k-chips.com>
To:	David Airlie <airlied@...ux.ie>, Heiko Stuebner <heiko@...ech.de>,
	dri-devel@...ts.freedesktop.org,
	linux-arm-kernel@...ts.infradead.org,
	linux-rockchip@...ts.infradead.org, linux-kernel@...r.kernel.org
Cc:	Mark Yao <mark.yao@...k-chips.com>
Subject: [PATCH v2 4/8] drm/rockchip: Optimization vop mode set

Rk3288 vop timing registers is immediately register, when configure
timing on display active time, will cause tearing. use dclk reset is
not a good idea to avoid this tearing. we can avoid tearing by using
standby register.

Vop standby register will take effect at end of current frame, and
go back to work immediately when exit standby.

So we can use standby register to protect this context.

Signed-off-by: Mark Yao <mark.yao@...k-chips.com>
---

Changes in v2: None

 drivers/gpu/drm/rockchip/rockchip_drm_vop.c |   49 +++++++++++++++++++--------
 1 file changed, 34 insertions(+), 15 deletions(-)

diff --git a/drivers/gpu/drm/rockchip/rockchip_drm_vop.c b/drivers/gpu/drm/rockchip/rockchip_drm_vop.c
index 58d7cc4..40cc8ed 100644
--- a/drivers/gpu/drm/rockchip/rockchip_drm_vop.c
+++ b/drivers/gpu/drm/rockchip/rockchip_drm_vop.c
@@ -1096,10 +1096,40 @@ static void vop_crtc_enable(struct drm_crtc *crtc)
 
 	vop_enable(crtc);
 	/*
-	 * disable dclk to stop frame scan, so that we can safe config mode and
-	 * enable iommu.
+	 * If dclk rate is zero, mean that scanout is stop,
+	 * we don't need wait any more.
 	 */
-	clk_disable(vop->dclk);
+	if (clk_get_rate(vop->dclk)) {
+		/*
+		 * Rk3288 vop timing register is immediately, when configure
+		 * display timing on display time, may cause tearing.
+		 *
+		 * Vop standby will take effect at end of current frame,
+		 * if dsp hold valid irq happen, it means standby complete.
+		 *
+		 * mode set:
+		 *    standby and wait complete --> |----
+		 *                                  | display time
+		 *                                  |----
+		 *                                  |---> dsp hold irq
+		 *     configure display timing --> |
+		 *         standby exit             |
+		 *                                  | new frame start.
+		 */
+
+		reinit_completion(&vop->dsp_hold_completion);
+		vop_dsp_hold_valid_irq_enable(vop);
+
+		spin_lock(&vop->reg_lock);
+
+		VOP_CTRL_SET(vop, standby, 1);
+
+		spin_unlock(&vop->reg_lock);
+
+		wait_for_completion(&vop->dsp_hold_completion);
+
+		vop_dsp_hold_valid_irq_disable(vop);
+	}
 
 	switch (vop->connector_type) {
 	case DRM_MODE_CONNECTOR_LVDS:
@@ -1135,20 +1165,9 @@ static void vop_crtc_enable(struct drm_crtc *crtc)
 	VOP_CTRL_SET(vop, vact_st_end, val);
 	VOP_CTRL_SET(vop, vpost_st_end, val);
 
-
-	/*
-	 * reset dclk, take all mode config affect, so the clk would run in
-	 * correct frame.
-	 */
-	reset_control_assert(vop->dclk_rst);
-	usleep_range(10, 20);
-	reset_control_deassert(vop->dclk_rst);
-
 	clk_set_rate(vop->dclk, adjusted_mode->clock * 1000);
-out:
-	if (clk_enable(vop->dclk) < 0)
-		dev_err(vop->dev, "failed to enable dclk - %d\n", ret_clk);
 
+	VOP_CTRL_SET(vop, standby, 0);
 }
 
 static void vop_crtc_atomic_flush(struct drm_crtc *crtc,
-- 
1.7.9.5


--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@...r.kernel.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html
Please read the FAQ at  http://www.tux.org/lkml/