From: Ondrej Zary The check for 53C80 registers accessibility was commented out because it was broken (inverted). Fix and enable it. Signed-off-by: Ondrej Zary Signed-off-by: Finn Thain Reviewed-by: Hannes Reinecke --- drivers/scsi/g_NCR5380.c | 37 ++++++------------------------------- 1 file changed, 6 insertions(+), 31 deletions(-) Index: linux/drivers/scsi/g_NCR5380.c =================================================================== --- linux.orig/drivers/scsi/g_NCR5380.c 2016-01-03 16:04:54.000000000 +1100 +++ linux/drivers/scsi/g_NCR5380.c 2016-01-03 16:04:55.000000000 +1100 @@ -609,14 +609,10 @@ static inline int NCR5380_pread(struct S if (!(NCR5380_read(hostdata->c400_ctl_status) & CSR_GATED_53C80_IRQ)) printk("53C400r: no 53C80 gated irq after transfer"); -#if 0 - /* - * DON'T DO THIS - THEY NEVER ARRIVE! - */ - printk("53C400r: Waiting for 53C80 registers\n"); - while (NCR5380_read(hostdata->c400_ctl_status) & CSR_53C80_REG) + /* wait for 53C80 registers to be available */ + while (!(NCR5380_read(hostdata->c400_ctl_status) & CSR_53C80_REG)) ; -#endif + if (!(NCR5380_read(BUS_AND_STATUS_REG) & BASR_END_DMA_TRANSFER)) printk(KERN_ERR "53C400r: no end dma signal\n"); @@ -638,7 +634,6 @@ static inline int NCR5380_pwrite(struct struct NCR5380_hostdata *hostdata = shost_priv(instance); int blocks = len / 128; int start = 0; - int i; NCR5380_write(hostdata->c400_ctl_status, CSR_BASE); NCR5380_write(hostdata->c400_blk_cnt, blocks); @@ -687,36 +682,16 @@ static inline int NCR5380_pwrite(struct blocks--; } -#if 0 - printk("53C400w: waiting for registers to be available\n"); - THEY NEVER DO ! while (NCR5380_read(hostdata->c400_ctl_status) & CSR_53C80_REG); - printk("53C400w: Got em\n"); -#endif - - /* Let's wait for this instead - could be ugly */ - /* All documentation says to check for this. Maybe my hardware is too - * fast. Waiting for it seems to work fine! KLL - */ - while (!(i = NCR5380_read(hostdata->c400_ctl_status) & CSR_GATED_53C80_IRQ)) { + /* wait for 53C80 registers to be available */ + while (!(NCR5380_read(hostdata->c400_ctl_status) & CSR_53C80_REG)) { udelay(4); /* DTC436 chip hangs without this */ /* FIXME - no timeout */ } - /* - * I know. i is certainly != 0 here but the loop is new. See previous - * comment. - */ - if (i) { - if (!((i = NCR5380_read(BUS_AND_STATUS_REG)) & BASR_END_DMA_TRANSFER)) - printk(KERN_ERR "53C400w: No END OF DMA bit - WHOOPS! BASR=%0x\n", i); - } else - printk(KERN_ERR "53C400w: no 53C80 gated irq after transfer (last block)\n"); - -#if 0 if (!(NCR5380_read(BUS_AND_STATUS_REG) & BASR_END_DMA_TRANSFER)) { printk(KERN_ERR "53C400w: no end dma signal\n"); } -#endif + while (!(NCR5380_read(TARGET_COMMAND_REG) & TCR_LAST_BYTE_SENT)) ; // TIMEOUT return 0; -- To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html Please read the FAQ at http://www.tux.org/lkml/