| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-ID: <1452177524-23192-4-git-send-email-ldewangan@nvidia.com>
Date: Thu, 7 Jan 2016 20:08:41 +0530
From: Laxman Dewangan <ldewangan@...dia.com>
To: <robh+dt@...nel.org>, <pawel.moll@....com>, <mark.rutland@....com>,
<ijc+devicetree@...lion.org.uk>, <galak@...eaurora.org>,
<linus.walleij@...aro.org>, <gnurou@...il.com>,
<lee.jones@...aro.org>, <broonie@...nel.org>,
<a.zummo@...ertech.it>, <alexandre.belloni@...e-electrons.com>
CC: <lgirdwood@...il.com>, <devicetree@...r.kernel.org>,
<linux-kernel@...r.kernel.org>, <linux-gpio@...r.kernel.org>,
<rtc-linux@...glegroups.com>, <swarren@...dia.com>,
<treding@...dia.com>, Laxman Dewangan <ldewangan@...dia.com>,
Chaitanya Bandi <bandik@...dia.com>
Subject: [PATCH 3/6] pinctrl: max77620: add pincontrol driver for MAX77620/MAX20024
MAXIM Semiconductor's PMIC, MAX77620/MAX20024 has 8 GPIO pins
which also act as the special function in alternate mode. Also
there is configuration like push-pull, open drain, FPS timing
etc for these pins.
Add pincontrol driver to configure these parameters through
pincontrol APIs.
Signed-off-by: Laxman Dewangan <ldewangan@...dia.com>
Signed-off-by: Chaitanya Bandi <bandik@...dia.com>
Tested-by: Venkat Reddy Talla <vreddytalla@...dia.com>
---
drivers/pinctrl/Kconfig | 10 +
drivers/pinctrl/Makefile | 1 +
drivers/pinctrl/pinctrl-max77620.c | 700 +++++++++++++++++++++++++++++++++++++
3 files changed, 711 insertions(+)
create mode 100644 drivers/pinctrl/pinctrl-max77620.c
diff --git a/drivers/pinctrl/Kconfig b/drivers/pinctrl/Kconfig
index 99a4c10..b6d2d23 100644
--- a/drivers/pinctrl/Kconfig
+++ b/drivers/pinctrl/Kconfig
@@ -227,6 +227,16 @@ config PINCTRL_COH901
COH 901 335 and COH 901 571/3. They contain 3, 5 or 7
ports of 8 GPIO pins each.
+config PINCTRL_MAX77620
+ bool "MAX77620/MAX20024 Pincontrol support"
+ depends on MFD_MAX77620
+ select GENERIC_PINCONF
+ help
+ Say Yes here to enable Pin control support for Maxim PMIC MAX77620.
+ This PMIC has 8 GPIO pins that work as GPIO as well as special
+ function in alternate mode. This driver also configure push-pull,
+ open drain, FPS slots etc.
+
config PINCTRL_PALMAS
bool "Pinctrl driver for the PALMAS Series MFD devices"
depends on OF && MFD_PALMAS
diff --git a/drivers/pinctrl/Makefile b/drivers/pinctrl/Makefile
index bf1b5ca..72833e3 100644
--- a/drivers/pinctrl/Makefile
+++ b/drivers/pinctrl/Makefile
@@ -17,6 +17,7 @@ obj-$(CONFIG_PINCTRL_AMD) += pinctrl-amd.o
obj-$(CONFIG_PINCTRL_DIGICOLOR) += pinctrl-digicolor.o
obj-$(CONFIG_PINCTRL_FALCON) += pinctrl-falcon.o
obj-$(CONFIG_PINCTRL_MESON) += meson/
+obj-$(CONFIG_PINCTRL_MAX77620) += pinctrl-max77620.o
obj-$(CONFIG_PINCTRL_PALMAS) += pinctrl-palmas.o
obj-$(CONFIG_PINCTRL_PISTACHIO) += pinctrl-pistachio.o
obj-$(CONFIG_PINCTRL_ROCKCHIP) += pinctrl-rockchip.o
diff --git a/drivers/pinctrl/pinctrl-max77620.c b/drivers/pinctrl/pinctrl-max77620.c
new file mode 100644
index 0000000..dc0584f
--- /dev/null
+++ b/drivers/pinctrl/pinctrl-max77620.c
@@ -0,0 +1,700 @@
+/*
+ * MAX77620 pin control driver.
+ *
+ * Copyright (c) 2016, NVIDIA CORPORATION. All rights reserved.
+ *
+ * Author:
+ * Chaitanya Bandi <bandik@...dia.com>
+ * Laxman Dewangan <ldewangan@...dia.com>
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms and conditions of the GNU General Public License,
+ * version 2, as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope it will be useful, but WITHOUT
+ * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for
+ * more details.
+ */
+
+#include <linux/delay.h>
+#include <linux/gpio.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/mfd/max77620.h>
+#include <linux/of.h>
+#include <linux/of_device.h>
+#include <linux/platform_device.h>
+#include <linux/pinctrl/consumer.h>
+#include <linux/pinctrl/machine.h>
+#include <linux/pinctrl/pinctrl.h>
+#include <linux/pinctrl/pinconf-generic.h>
+#include <linux/pinctrl/pinconf.h>
+#include <linux/pinctrl/pinmux.h>
+#include <linux/pm.h>
+#include <linux/slab.h>
+
+#include "core.h"
+#include "pinconf.h"
+#include "pinctrl-utils.h"
+
+#define MAX77620_PIN_NUM 8
+
+enum max77620_pin_ppdrv {
+ MAX77620_PIN_UNCONFIG_DRV,
+ MAX77620_PIN_OD_DRV,
+ MAX77620_PIN_PP_DRV,
+};
+
+enum max77620_pinconf_param {
+ MAX77620_ACTIVE_FPS_SOURCE = PIN_CONFIG_END + 1,
+ MAX77620_ACTIVE_FPS_POWER_ON_SLOTS,
+ MAX77620_ACTIVE_FPS_POWER_DOWN_SLOTS,
+ MAX77620_SUSPEND_FPS_SOURCE,
+ MAX77620_SUSPEND_FPS_POWER_ON_SLOTS,
+ MAX77620_SUSPEND_FPS_POWER_DOWN_SLOTS,
+};
+
+struct max77620_pin_function {
+ const char *name;
+ const char * const *groups;
+ unsigned ngroups;
+ int mux_option;
+};
+
+struct max77620_cfg_param {
+ const char *property;
+ enum max77620_pinconf_param param;
+};
+
+static const struct pinconf_generic_params max77620_cfg_params[] = {
+ {
+ .property = "maxim,active-fps-source",
+ .param = MAX77620_ACTIVE_FPS_SOURCE,
+ }, {
+ .property = "maxim,active-fps-power-up-slot",
+ .param = MAX77620_ACTIVE_FPS_POWER_ON_SLOTS,
+ }, {
+ .property = "maxim,active-fps-power-down-slot",
+ .param = MAX77620_ACTIVE_FPS_POWER_DOWN_SLOTS,
+ }, {
+ .property = "maxim,suspend-fps-source",
+ .param = MAX77620_SUSPEND_FPS_SOURCE,
+ }, {
+ .property = "maxim,suspend-fps-power-up-slot",
+ .param = MAX77620_SUSPEND_FPS_POWER_ON_SLOTS,
+ }, {
+ .property = "maxim,suspend-fps-power-down-slot",
+ .param = MAX77620_SUSPEND_FPS_POWER_DOWN_SLOTS,
+ },
+};
+
+enum max77620_alternate_pinmux_option {
+ MAX77620_PINMUX_GPIO = 0,
+ MAX77620_PINMUX_LOW_POWER_MODE_CONTROL_IN = 1,
+ MAX77620_PINMUX_FLEXIBLE_POWER_SEQUENCER_OUT = 2,
+ MAX77620_PINMUX_32K_OUT1 = 3,
+ MAX77620_PINMUX_SD0_DYNAMIC_VOLTAGE_SCALING_IN = 4,
+ MAX77620_PINMUX_SD1_DYNAMIC_VOLTAGE_SCALING_IN = 5,
+ MAX77620_PINMUX_REFERENCE_OUT = 6,
+};
+
+struct max77620_pingroup {
+ const char *name;
+ const unsigned pins[1];
+ unsigned npins;
+ enum max77620_alternate_pinmux_option alt_option;
+};
+
+struct max77620_pin_info {
+ enum max77620_pin_ppdrv drv_type;
+ int pull_config;
+};
+
+struct max77620_fps_config {
+ int active_fps_src;
+ int active_power_up_slots;
+ int active_power_down_slots;
+ int suspend_fps_src;
+ int suspend_power_up_slots;
+ int suspend_power_down_slots;
+};
+
+struct max77620_pctrl_info {
+ struct device *dev;
+ struct pinctrl_dev *pctl;
+ struct max77620_chip *max77620;
+ int pins_current_opt[MAX77620_GPIO_NR];
+ const struct max77620_pin_function *functions;
+ unsigned num_functions;
+ const struct max77620_pingroup *pin_groups;
+ int num_pin_groups;
+ const struct pinctrl_pin_desc *pins;
+ unsigned num_pins;
+ struct max77620_pin_info pin_info[MAX77620_PIN_NUM];
+ struct max77620_fps_config fps_config[MAX77620_PIN_NUM];
+};
+
+static const struct pinctrl_pin_desc max77620_pins_desc[] = {
+ PINCTRL_PIN(MAX77620_GPIO0, "gpio0"),
+ PINCTRL_PIN(MAX77620_GPIO1, "gpio1"),
+ PINCTRL_PIN(MAX77620_GPIO2, "gpio2"),
+ PINCTRL_PIN(MAX77620_GPIO3, "gpio3"),
+ PINCTRL_PIN(MAX77620_GPIO4, "gpio4"),
+ PINCTRL_PIN(MAX77620_GPIO5, "gpio5"),
+ PINCTRL_PIN(MAX77620_GPIO6, "gpio6"),
+ PINCTRL_PIN(MAX77620_GPIO7, "gpio7"),
+};
+
+static const char * const gpio_groups[] = {
+ "gpio0",
+ "gpio1",
+ "gpio2",
+ "gpio3",
+ "gpio4",
+ "gpio5",
+ "gpio6",
+ "gpio7",
+};
+
+#define FUNCTION_GROUP(fname, mux) \
+ { \
+ .name = #fname, \
+ .groups = gpio_groups, \
+ .ngroups = ARRAY_SIZE(gpio_groups), \
+ .mux_option = MAX77620_PINMUX_##mux, \
+ }
+
+static const struct max77620_pin_function max77620_pin_function[] = {
+ FUNCTION_GROUP(gpio, GPIO),
+ FUNCTION_GROUP(lpm-control-in, LOW_POWER_MODE_CONTROL_IN),
+ FUNCTION_GROUP(fps-out, FLEXIBLE_POWER_SEQUENCER_OUT),
+ FUNCTION_GROUP(32k-out1, 32K_OUT1),
+ FUNCTION_GROUP(sd0-dvs-in, SD0_DYNAMIC_VOLTAGE_SCALING_IN),
+ FUNCTION_GROUP(sd1-dvs-in, SD1_DYNAMIC_VOLTAGE_SCALING_IN),
+ FUNCTION_GROUP(reference-out, REFERENCE_OUT),
+};
+
+#define MAX77620_PINGROUP(pg_name, pin_id, option) \
+ { \
+ .name = #pg_name, \
+ .pins = {MAX77620_##pin_id}, \
+ .npins = 1, \
+ .alt_option = MAX77620_PINMUX_##option, \
+ }
+
+static const struct max77620_pingroup max77620_pingroups[] = {
+ MAX77620_PINGROUP(gpio0, GPIO0, LOW_POWER_MODE_CONTROL_IN),
+ MAX77620_PINGROUP(gpio1, GPIO1, FLEXIBLE_POWER_SEQUENCER_OUT),
+ MAX77620_PINGROUP(gpio2, GPIO2, FLEXIBLE_POWER_SEQUENCER_OUT),
+ MAX77620_PINGROUP(gpio3, GPIO3, FLEXIBLE_POWER_SEQUENCER_OUT),
+ MAX77620_PINGROUP(gpio4, GPIO4, 32K_OUT1),
+ MAX77620_PINGROUP(gpio5, GPIO5, SD0_DYNAMIC_VOLTAGE_SCALING_IN),
+ MAX77620_PINGROUP(gpio6, GPIO6, SD1_DYNAMIC_VOLTAGE_SCALING_IN),
+ MAX77620_PINGROUP(gpio7, GPIO7, REFERENCE_OUT),
+};
+
+static int max77620_pinctrl_get_groups_count(struct pinctrl_dev *pctldev)
+{
+ struct max77620_pctrl_info *mpci = pinctrl_dev_get_drvdata(pctldev);
+
+ return mpci->num_pin_groups;
+}
+
+static const char *max77620_pinctrl_get_group_name(struct pinctrl_dev *pctldev,
+ unsigned group)
+{
+ struct max77620_pctrl_info *mpci = pinctrl_dev_get_drvdata(pctldev);
+
+ return mpci->pin_groups[group].name;
+}
+
+static int max77620_pinctrl_get_group_pins(struct pinctrl_dev *pctldev,
+ unsigned group, const unsigned **pins, unsigned *num_pins)
+{
+ struct max77620_pctrl_info *mpci = pinctrl_dev_get_drvdata(pctldev);
+
+ *pins = mpci->pin_groups[group].pins;
+ *num_pins = mpci->pin_groups[group].npins;
+ return 0;
+}
+
+static const struct pinctrl_ops max77620_pinctrl_ops = {
+ .get_groups_count = max77620_pinctrl_get_groups_count,
+ .get_group_name = max77620_pinctrl_get_group_name,
+ .get_group_pins = max77620_pinctrl_get_group_pins,
+ .dt_node_to_map = pinconf_generic_dt_node_to_map_pin,
+ .dt_free_map = pinctrl_utils_dt_free_map,
+};
+
+static int max77620_pinctrl_get_funcs_count(struct pinctrl_dev *pctldev)
+{
+ struct max77620_pctrl_info *mpci = pinctrl_dev_get_drvdata(pctldev);
+
+ return mpci->num_functions;
+}
+
+static const char *max77620_pinctrl_get_func_name(struct pinctrl_dev *pctldev,
+ unsigned function)
+{
+ struct max77620_pctrl_info *mpci = pinctrl_dev_get_drvdata(pctldev);
+
+ return mpci->functions[function].name;
+}
+
+static int max77620_pinctrl_get_func_groups(struct pinctrl_dev *pctldev,
+ unsigned function, const char * const **groups,
+ unsigned * const num_groups)
+{
+ struct max77620_pctrl_info *mpci = pinctrl_dev_get_drvdata(pctldev);
+
+ *groups = mpci->functions[function].groups;
+ *num_groups = mpci->functions[function].ngroups;
+ return 0;
+}
+
+static int max77620_pinctrl_enable(struct pinctrl_dev *pctldev,
+ unsigned function, unsigned group)
+{
+ struct max77620_pctrl_info *mpci = pinctrl_dev_get_drvdata(pctldev);
+
+ if (function == MAX77620_PINMUX_GPIO) {
+ max77620_reg_update(mpci->max77620->dev,
+ MAX77620_PWR_SLAVE, MAX77620_REG_AME_GPIO,
+ 1 << group, 0);
+ } else if (function == mpci->pin_groups[group].alt_option) {
+ max77620_reg_update(mpci->max77620->dev,
+ MAX77620_PWR_SLAVE, MAX77620_REG_AME_GPIO,
+ 1 << group, 1 << group);
+ } else {
+ dev_err(mpci->dev, "GPIO %u doesn't have function %u\n",
+ group, function);
+ return -EINVAL;
+ }
+ return 0;
+}
+
+static const struct pinmux_ops max77620_pinmux_ops = {
+ .get_functions_count = max77620_pinctrl_get_funcs_count,
+ .get_function_name = max77620_pinctrl_get_func_name,
+ .get_function_groups = max77620_pinctrl_get_func_groups,
+ .set_mux = max77620_pinctrl_enable,
+};
+
+static int max77620_pinconf_get(struct pinctrl_dev *pctldev,
+ unsigned pin, unsigned long *config)
+{
+ struct max77620_pctrl_info *mpci = pinctrl_dev_get_drvdata(pctldev);
+ enum pin_config_param param = pinconf_to_config_param(*config);
+ u8 val;
+ int arg = 0;
+ int ret;
+
+ switch (param) {
+ case PIN_CONFIG_DRIVE_OPEN_DRAIN:
+ if (mpci->pin_info[pin].drv_type == MAX77620_PIN_OD_DRV)
+ arg = 1;
+ break;
+
+ case PIN_CONFIG_DRIVE_PUSH_PULL:
+ if (mpci->pin_info[pin].drv_type == MAX77620_PIN_PP_DRV)
+ arg = 1;
+ break;
+
+ case PIN_CONFIG_BIAS_PULL_UP:
+ ret = max77620_reg_read(mpci->max77620->dev,
+ MAX77620_PWR_SLAVE, MAX77620_REG_PUE_GPIO, &val);
+ if (ret < 0) {
+ dev_err(mpci->dev,
+ "Reg PUE_GPIO read failed: %d\n", ret);
+ return ret;
+ }
+ if (val & BIT(pin))
+ arg = 1;
+ break;
+
+ case PIN_CONFIG_BIAS_PULL_DOWN:
+ ret = max77620_reg_read(mpci->max77620->dev,
+ MAX77620_PWR_SLAVE, MAX77620_REG_PDE_GPIO, &val);
+ if (ret < 0) {
+ dev_err(mpci->dev,
+ "Reg PDE_GPIO read failed: %d\n", ret);
+ return ret;
+ }
+ if (val & BIT(pin))
+ arg = 1;
+ break;
+
+ default:
+ dev_err(mpci->dev, "Properties not supported\n");
+ return -ENOTSUPP;
+ }
+
+ *config = pinconf_to_config_packed(param, (u16)arg);
+ return 0;
+}
+
+static int max77620_get_default_fps(struct max77620_pctrl_info *mpci,
+ int addr, int *fps)
+{
+ u8 val;
+ int ret;
+
+ ret = max77620_reg_read(mpci->max77620->dev,
+ MAX77620_PWR_SLAVE, addr, &val);
+ if (ret < 0) {
+ dev_err(mpci->dev, "Reg PUE_GPIO read failed: %d\n", ret);
+ return ret;
+ }
+ val = (val & MAX77620_FPS_SRC_MASK) >> MAX77620_FPS_SRC_SHIFT;
+ *fps = val;
+ return 0;
+}
+
+static int max77620_set_fps_param(struct max77620_pctrl_info *mpci,
+ int pin, int param)
+{
+ struct max77620_fps_config *fps_config = &mpci->fps_config[pin];
+ int addr, ret;
+ int param_val;
+ int mask, shift;
+
+ if ((pin < MAX77620_GPIO1) || (pin > MAX77620_GPIO3))
+ return 0;
+
+ addr = MAX77620_REG_FPS_GPIO1 + pin - 1;
+ switch (param) {
+ case MAX77620_ACTIVE_FPS_SOURCE:
+ case MAX77620_SUSPEND_FPS_SOURCE:
+ mask = MAX77620_FPS_SRC_MASK;
+ shift = MAX77620_FPS_SRC_SHIFT;
+ param_val = fps_config->active_fps_src;
+ if (param == MAX77620_SUSPEND_FPS_SOURCE)
+ param_val = fps_config->suspend_fps_src;
+ break;
+
+ case MAX77620_ACTIVE_FPS_POWER_ON_SLOTS:
+ case MAX77620_SUSPEND_FPS_POWER_ON_SLOTS:
+ mask = MAX77620_FPS_PU_PERIOD_MASK;
+ shift = MAX77620_FPS_PU_PERIOD_SHIFT;
+ param_val = fps_config->active_power_up_slots;
+ if (param == MAX77620_SUSPEND_FPS_POWER_ON_SLOTS)
+ param_val = fps_config->suspend_power_up_slots;
+ break;
+
+ case MAX77620_ACTIVE_FPS_POWER_DOWN_SLOTS:
+ case MAX77620_SUSPEND_FPS_POWER_DOWN_SLOTS:
+ mask = MAX77620_FPS_PD_PERIOD_MASK;
+ shift = MAX77620_FPS_PD_PERIOD_SHIFT;
+ param_val = fps_config->active_power_down_slots;
+ if (param == MAX77620_SUSPEND_FPS_POWER_DOWN_SLOTS)
+ param_val = fps_config->suspend_power_down_slots;
+ break;
+
+ default:
+ return -EINVAL;
+ };
+
+ if (param_val < 0)
+ return 0;
+
+ ret = max77620_reg_update(mpci->max77620->dev,
+ MAX77620_PWR_SLAVE, addr, mask, param_val << shift);
+ if (ret < 0) {
+ dev_err(mpci->dev,
+ "Reg 0x%02x update failed %d\n", addr, ret);
+ return ret;
+ }
+ return 0;
+}
+
+static int max77620_pinconf_set(struct pinctrl_dev *pctldev,
+ unsigned pin, unsigned long *configs,
+ unsigned num_configs)
+{
+ struct max77620_pctrl_info *mpci = pinctrl_dev_get_drvdata(pctldev);
+ struct max77620_fps_config *fps_config;
+ int param;
+ u16 param_val;
+ unsigned int val;
+ unsigned int pu_val;
+ unsigned int pd_val;
+ int addr, ret;
+ int i;
+
+ for (i = 0; i < num_configs; i++) {
+ param = pinconf_to_config_param(configs[i]);
+ param_val = pinconf_to_config_argument(configs[i]);
+
+ switch (param) {
+ case PIN_CONFIG_DRIVE_OPEN_DRAIN:
+ val = param_val ? 0 : 1;
+ max77620_reg_update(mpci->max77620->dev,
+ MAX77620_PWR_SLAVE, MAX77620_REG_GPIO0 + pin,
+ MAX77620_CNFG_GPIO_DRV_MASK, val);
+ mpci->pin_info[pin].drv_type = val ?
+ MAX77620_PIN_PP_DRV : MAX77620_PIN_OD_DRV;
+ break;
+
+ case PIN_CONFIG_DRIVE_PUSH_PULL:
+ val = param_val ? 1 : 0;
+ max77620_reg_update(mpci->max77620->dev,
+ MAX77620_PWR_SLAVE, MAX77620_REG_GPIO0 + pin,
+ MAX77620_CNFG_GPIO_DRV_MASK, val);
+ mpci->pin_info[pin].drv_type = val ?
+ MAX77620_PIN_PP_DRV : MAX77620_PIN_OD_DRV;
+ break;
+
+ case MAX77620_ACTIVE_FPS_SOURCE:
+ case MAX77620_ACTIVE_FPS_POWER_ON_SLOTS:
+ case MAX77620_ACTIVE_FPS_POWER_DOWN_SLOTS:
+ if ((pin < MAX77620_GPIO1) || (pin > MAX77620_GPIO3))
+ return -EINVAL;
+
+ fps_config = &mpci->fps_config[pin];
+
+ if ((param == MAX77620_ACTIVE_FPS_SOURCE) &&
+ (param_val == FPS_SRC_DEF)) {
+ addr = MAX77620_REG_FPS_GPIO1 + pin - 1;
+ ret = max77620_get_default_fps(mpci,
+ addr, &fps_config->active_fps_src);
+ if (ret < 0)
+ return ret;
+ break;
+ }
+
+ if (param == MAX77620_ACTIVE_FPS_SOURCE)
+ fps_config->active_fps_src = param_val;
+ else if (param == MAX77620_ACTIVE_FPS_POWER_ON_SLOTS)
+ fps_config->active_power_up_slots = param_val;
+ else
+ fps_config->active_power_down_slots = param_val;
+
+ ret = max77620_set_fps_param(mpci, pin, param);
+ if (ret < 0) {
+ dev_err(mpci->dev,
+ "Pin-%d Param %d config failed: %d\n",
+ pin, param, ret);
+ return ret;
+ }
+ break;
+
+ case MAX77620_SUSPEND_FPS_SOURCE:
+ case MAX77620_SUSPEND_FPS_POWER_ON_SLOTS:
+ case MAX77620_SUSPEND_FPS_POWER_DOWN_SLOTS:
+ if ((pin < MAX77620_GPIO1) || (pin > MAX77620_GPIO3))
+ return -EINVAL;
+
+ fps_config = &mpci->fps_config[pin];
+
+ if ((param == MAX77620_SUSPEND_FPS_SOURCE) &&
+ (param_val == FPS_SRC_DEF)) {
+ addr = MAX77620_REG_FPS_GPIO1 + pin - 1;
+ ret = max77620_get_default_fps(mpci,
+ addr, &fps_config->suspend_fps_src);
+ if (ret < 0)
+ return ret;
+ break;
+ }
+
+ if (param == MAX77620_SUSPEND_FPS_SOURCE)
+ fps_config->suspend_fps_src = param_val;
+ else if (param == MAX77620_SUSPEND_FPS_POWER_ON_SLOTS)
+ fps_config->suspend_power_up_slots = param_val;
+ else
+ fps_config->suspend_power_down_slots =
+ param_val;
+ break;
+
+ case PIN_CONFIG_BIAS_PULL_UP:
+ case PIN_CONFIG_BIAS_PULL_DOWN:
+ pu_val = (param == PIN_CONFIG_BIAS_PULL_UP) ?
+ BIT(pin) : 0;
+ pd_val = (param == PIN_CONFIG_BIAS_PULL_DOWN) ?
+ BIT(pin) : 0;
+
+ ret = max77620_reg_update(mpci->max77620->dev,
+ MAX77620_PWR_SLAVE, MAX77620_REG_PUE_GPIO,
+ BIT(pin), pu_val);
+ if (ret < 0) {
+ dev_err(mpci->dev,
+ "PUE_GPIO update failed: %d\n", ret);
+ return ret;
+ }
+
+ ret = max77620_reg_update(mpci->max77620->dev,
+ MAX77620_PWR_SLAVE, MAX77620_REG_PDE_GPIO,
+ BIT(pin), pd_val);
+ if (ret < 0) {
+ dev_err(mpci->dev,
+ "PDE_GPIO update failed: %d\n", ret);
+ return ret;
+ }
+ break;
+
+ default:
+ dev_err(mpci->dev, "Properties not supported\n");
+ return -ENOTSUPP;
+
+ }
+ }
+
+ return 0;
+}
+
+static const struct pinconf_ops max77620_pinconf_ops = {
+ .pin_config_get = max77620_pinconf_get,
+ .pin_config_set = max77620_pinconf_set,
+};
+
+static struct pinctrl_desc max77620_pinctrl_desc = {
+ .pctlops = &max77620_pinctrl_ops,
+ .pmxops = &max77620_pinmux_ops,
+ .confops = &max77620_pinconf_ops,
+ .owner = THIS_MODULE,
+};
+
+static int max77620_pinctrl_probe(struct platform_device *pdev)
+{
+ struct max77620_pctrl_info *mpci;
+ struct max77620_chip *max77620 = dev_get_drvdata(pdev->dev.parent);
+ int i;
+
+ mpci = devm_kzalloc(&pdev->dev, sizeof(*mpci), GFP_KERNEL);
+ if (!mpci)
+ return -ENOMEM;
+
+ mpci->dev = &pdev->dev;
+ mpci->dev->of_node = pdev->dev.parent->of_node;
+ mpci->max77620 = max77620;
+
+ mpci->pins = max77620_pins_desc;
+ mpci->num_pins = ARRAY_SIZE(max77620_pins_desc);
+ mpci->functions = max77620_pin_function;
+ mpci->num_functions = ARRAY_SIZE(max77620_pin_function);
+ mpci->pin_groups = max77620_pingroups;
+ mpci->num_pin_groups = ARRAY_SIZE(max77620_pingroups);
+ platform_set_drvdata(pdev, mpci);
+
+ max77620_pinctrl_desc.name = dev_name(&pdev->dev);
+ max77620_pinctrl_desc.pins = max77620_pins_desc;
+ max77620_pinctrl_desc.npins = ARRAY_SIZE(max77620_pins_desc);
+ max77620_pinctrl_desc.num_custom_params =
+ ARRAY_SIZE(max77620_cfg_params);
+ max77620_pinctrl_desc.custom_params = max77620_cfg_params;
+
+ for (i = 0; i < MAX77620_PIN_NUM; ++i) {
+ mpci->fps_config[i].active_fps_src = -1;
+ mpci->fps_config[i].active_power_up_slots = -1;
+ mpci->fps_config[i].active_power_down_slots = -1;
+ mpci->fps_config[i].suspend_fps_src = -1;
+ mpci->fps_config[i].suspend_power_up_slots = -1;
+ mpci->fps_config[i].suspend_power_down_slots = -1;
+ }
+
+ mpci->pctl = pinctrl_register(&max77620_pinctrl_desc,
+ &pdev->dev, mpci);
+ if (!mpci->pctl) {
+ dev_err(&pdev->dev, "Couldn't register pinctrl driver\n");
+ return -EINVAL;
+ }
+
+ return 0;
+}
+
+static int max77620_pinctrl_remove(struct platform_device *pdev)
+{
+ struct max77620_pctrl_info *mpci = platform_get_drvdata(pdev);
+
+ pinctrl_unregister(mpci->pctl);
+ return 0;
+}
+
+#ifdef CONFIG_PM_SLEEP
+static int max77620_pinctrl_suspend(struct device *dev)
+{
+ struct max77620_pctrl_info *mpci = dev_get_drvdata(dev);
+ int pin, p;
+ int ret;
+ int param[] = {MAX77620_SUSPEND_FPS_SOURCE,
+ MAX77620_SUSPEND_FPS_POWER_ON_SLOTS,
+ MAX77620_SUSPEND_FPS_POWER_DOWN_SLOTS};
+
+ for (pin = 0; pin < MAX77620_PIN_NUM; ++pin) {
+ if ((pin < MAX77620_GPIO1) || (pin > MAX77620_GPIO3))
+ continue;
+ for (p = 0; p < 3; ++p) {
+ ret = max77620_set_fps_param(mpci,
+ pin, param[p]);
+ if (ret < 0)
+ dev_err(dev, "Pin-%d config %d failed: %d\n",
+ pin, param[p], ret);
+ }
+ }
+ return 0;
+};
+
+static int max77620_pinctrl_resume(struct device *dev)
+{
+ struct max77620_pctrl_info *mpci = dev_get_drvdata(dev);
+ int pin, p;
+ int ret;
+ int param[] = {MAX77620_ACTIVE_FPS_SOURCE,
+ MAX77620_ACTIVE_FPS_POWER_ON_SLOTS,
+ MAX77620_ACTIVE_FPS_POWER_DOWN_SLOTS};
+
+ for (pin = 0; pin < MAX77620_PIN_NUM; ++pin) {
+ if ((pin < MAX77620_GPIO1) || (pin > MAX77620_GPIO3))
+ continue;
+ for (p = 0; p < 3; ++p) {
+ ret = max77620_set_fps_param(mpci, pin, param[p]);
+ if (ret < 0)
+ dev_err(dev, "Pin-%d config %d failed: %d\n",
+ pin, param[p], ret);
+ }
+ }
+ return 0;
+}
+#endif
+
+static const struct dev_pm_ops max77620_pinctrl_pm_ops = {
+ SET_SYSTEM_SLEEP_PM_OPS(max77620_pinctrl_suspend,
+ max77620_pinctrl_resume)
+};
+
+static struct platform_device_id max77620_pinctrl_devtype[] = {
+ {
+ .name = "max77620-pinctrl",
+ }, {
+ .name = "max20024-pinctrl",
+ },
+};
+
+static struct platform_driver max77620_pinctrl_driver = {
+ .driver = {
+ .name = "max77620-pinctrl",
+ .owner = THIS_MODULE,
+ .pm = &max77620_pinctrl_pm_ops,
+ },
+ .probe = max77620_pinctrl_probe,
+ .remove = max77620_pinctrl_remove,
+ .id_table = max77620_pinctrl_devtype,
+};
+
+static int __init max77620_pinctrl_init(void)
+{
+ return platform_driver_register(&max77620_pinctrl_driver);
+}
+subsys_initcall(max77620_pinctrl_init);
+
+static void __exit max77620_pinctrl_exit(void)
+{
+ platform_driver_unregister(&max77620_pinctrl_driver);
+}
+module_exit(max77620_pinctrl_exit);
+
+MODULE_DESCRIPTION("MAX77620/MAX20024 pin control driver");
+MODULE_AUTHOR("Chaitanya Bandi<bandik@...dia.com>");
+MODULE_AUTHOR("Laxman Dewangan<ldewangan@...dia.com>");
+MODULE_ALIAS("platform:max77620-pinctrl");
+MODULE_LICENSE("GPL v2");
--
2.1.4
--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@...r.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
Powered by blists - more mailing lists