[<prev] [next>] [<thread-prev] [thread-next>] [day] [month] [year] [list]
Message-Id: <1452784104-30840-12-git-send-email-anton.wuerfel@fau.de>
Date: Thu, 14 Jan 2016 16:08:20 +0100
From: Anton Wuerfel <anton.wuerfel@....de>
To: Greg Kroah-Hartman <gregkh@...uxfoundation.org>
Cc: Jiri Slaby <jslaby@...e.com>,
"James E.J. Bottomley" <jejb@...isc-linux.org>,
Helge Deller <deller@....de>,
Joachim Eastwood <manabian@...il.com>,
Matthias Brugger <matthias.bgg@...il.com>,
Masahiro Yamada <yamada.masahiro@...ionext.com>,
Peter Hurley <peter@...leysoftware.com>,
Sebastian Andrzej Siewior <bigeasy@...utronix.de>,
Andy Shevchenko <andriy.shevchenko@...ux.intel.com>,
Phillip Raffeck <phillip.raffeck@....de>,
Heikki Krogerus <heikki.krogerus@...ux.intel.com>,
Peter Hung <hpeter@...il.com>, linux-serial@...r.kernel.org,
linux-kernel@...r.kernel.org, linux-parisc@...r.kernel.org,
linux-kernel@...cs.fau.de,
Anton Würfel <anton.wuerfel@....de>
Subject: [PATCH v7 11/15] tty: serial: 8250: Remove SERIAL_DEBUG_PNP macro
From: Phillip Raffeck <phillip.raffeck@....de>
This patch removes the macro SERIAL_DEBUG_PNP, which is used to enable
debugging at compile time.
As SERIAL_DEBUG_PNP is an orphan, the corresponding #ifdef is removed.
To keep the ability to enable debugging at compile time,
the call to printk(KERN_DEBUG ...) is replaced by a corresponding
call to dev_dbg(), which is configurable via CONFIG_DYNAMIC_DEBUG.
Signed-off-by: Phillip Raffeck <phillip.raffeck@....de>
Signed-off-by: Anton Würfel <anton.wuerfel@....de>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@...ux.intel.com>
Cc: linux-kernel@...cs.fau.de
---
drivers/tty/serial/8250/8250_pnp.c | 10 +++++-----
1 file changed, 5 insertions(+), 5 deletions(-)
diff --git a/drivers/tty/serial/8250/8250_pnp.c b/drivers/tty/serial/8250/8250_pnp.c
index 00846a7..0c32c59 100644
--- a/drivers/tty/serial/8250/8250_pnp.c
+++ b/drivers/tty/serial/8250/8250_pnp.c
@@ -464,11 +464,11 @@ serial_pnp_probe(struct pnp_dev *dev, const struct pnp_device_id *dev_id)
} else
return -ENODEV;
-#ifdef SERIAL_DEBUG_PNP
- printk(KERN_DEBUG
- "Setup PNP port: port %x, mem 0x%lx, irq %d, type %d\n",
- uart.port.iobase, uart.port.mapbase, uart.port.irq, uart.port.iotype);
-#endif
+ dev_dbg(&dev->dev,
+ "Setup PNP port: port %x, mem 0x%lx, irq %d, type %d\n",
+ uart.port.iobase, uart.port.mapbase,
+ uart.port.irq, uart.port.iotype);
+
if (flags & CIR_PORT) {
uart.port.flags |= UPF_FIXED_PORT | UPF_FIXED_TYPE;
uart.port.type = PORT_8250_CIR;
--
1.9.1
Powered by blists - more mailing lists