| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Date: Wed, 3 Feb 2016 11:28:26 +0000
From: Joao Pinto <Joao.Pinto@...opsys.com>
To: santosh.sy@...sung.com, h.vinayak@...sung.com,
julian.calaby@...il.com, akinobu.mita@...il.com, hch@...radead.org
Cc: gbroner@...eaurora.org, subhashj@...eaurora.org,
CARLOS.PALMINHA@...opsys.com, ijc+devicetree@...lion.org.uk,
linux-kernel@...r.kernel.org, linux-scsi@...r.kernel.org,
devicetree@...r.kernel.org, Joao Pinto <Joao.Pinto@...opsys.com>
Subject: [PATCH 3/3] add support for DWC UFS Host Controller
Signed-off-by: Joao Pinto <jpinto@...opsys.com>
---
Documentation/devicetree/bindings/ufs/ufs-dwc.txt | 16 +
MAINTAINERS | 6 +
drivers/scsi/ufs/Kconfig | 45 ++
drivers/scsi/ufs/Makefile | 2 +
drivers/scsi/ufs/ufs-dwc.c | 96 +++
drivers/scsi/ufs/ufshcd-dwc.c | 768 ++++++++++++++++++++++
drivers/scsi/ufs/ufshcd-dwc.h | 26 +
drivers/scsi/ufs/ufshcd-pci.c | 20 +
drivers/scsi/ufs/ufshcd.c | 32 +-
drivers/scsi/ufs/ufshcd.h | 22 +
drivers/scsi/ufs/ufshci-dwc.h | 42 ++
drivers/scsi/ufs/unipro.h | 39 ++
12 files changed, 1100 insertions(+), 14 deletions(-)
create mode 100644 Documentation/devicetree/bindings/ufs/ufs-dwc.txt
create mode 100644 drivers/scsi/ufs/ufs-dwc.c
create mode 100644 drivers/scsi/ufs/ufshcd-dwc.c
create mode 100644 drivers/scsi/ufs/ufshcd-dwc.h
create mode 100644 drivers/scsi/ufs/ufshci-dwc.h
diff --git a/Documentation/devicetree/bindings/ufs/ufs-dwc.txt b/Documentation/devicetree/bindings/ufs/ufs-dwc.txt
new file mode 100644
index 0000000..fa361f2
--- /dev/null
+++ b/Documentation/devicetree/bindings/ufs/ufs-dwc.txt
@@ -0,0 +1,16 @@
+* Universal Flash Storage (UFS) DesignWare Host Controller
+
+DWC_UFSHC nodes are defined to describe on-chip UFS host controllers.
+Each UFS controller instance should have its own node.
+
+Required properties:
+- compatible : compatible list, contains "snps,ufshcd"
+- reg : <registers mapping>
+- interrupts : <interrupt mapping for UFS host controller IRQ>
+
+Example:
+ dwc_ufshcd@...0000000 {
+ compatible = "snps,ufshcd";
+ reg = < 0xD0000000 0x10000 >;
+ interrupts = < 24 >;
+ };
diff --git a/MAINTAINERS b/MAINTAINERS
index d2f94e2..b5d2fdb 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -11006,6 +11006,12 @@ S: Supported
F: Documentation/scsi/ufs.txt
F: drivers/scsi/ufs/
+UNIVERSAL FLASH STORAGE HOST CONTROLLER DRIVER DWC HOOKS
+M: Joao Pinto <Joao.Pinto@...opsys.com>
+L: linux-scsi@...r.kernel.org
+S: Supported
+F: drivers/scsi/ufs/*-dwc-*
+
UNSORTED BLOCK IMAGES (UBI)
M: Artem Bityutskiy <dedekind1@...il.com>
M: Richard Weinberger <richard@....at>
diff --git a/drivers/scsi/ufs/Kconfig b/drivers/scsi/ufs/Kconfig
index 5f45307..86be4c8 100644
--- a/drivers/scsi/ufs/Kconfig
+++ b/drivers/scsi/ufs/Kconfig
@@ -83,3 +83,48 @@ config SCSI_UFS_QCOM
Select this if you have UFS controller on QCOM chipset.
If unsure, say N.
+
+config SCSI_UFS_DWC_HOOKS
+ bool "DesignWare hooks to UFS controller"
+ depends on SCSI_UFSHCD
+ ---help---
+ This selects the DesignWare hooks for the UFS host controller.
+
+ Select this if you have a DesignWare UFS controller.
+ If unsure, say N.
+
+config SCSI_UFS_DWC_PLAT
+ tristate "DesignWare UFS controller platform glue driver"
+ depends on SCSI_UFS_DWC_HOOKS && SCSI_UFSHCD_PLATFORM
+ ---help---
+ This selects the DesignWare UFS host controller platform glue driver.
+
+ Select this if you have a DesignWare UFS controller on Platform bus.
+ If unsure, say N.
+
+config SCSI_UFS_DWC_MPHY_TC
+ bool "Support for the Synopsys MPHY Test Chip"
+ depends on SCSI_UFS_DWC_HOOKS && (SCSI_UFSHCD_PCI || SCSI_UFS_DWC_PLAT)
+ ---help---
+ This selects the support for the Synopsys MPHY Test Chip.
+
+ Select this if you have a Synopsys MPHY Test Chip.
+ If unsure, say N.
+
+config SCSI_UFS_DWC_20BIT_RMMI
+ bool "20-bit RMMI MPHY"
+ depends on SCSI_UFS_DWC_MPHY_TC
+ ---help---
+ This specifies that the Synopsys MPHY supports 40-bit RMMI operations.
+
+ Select this if you are using a 40-bit RMMI Synopsys MPHY.
+ If unsure, say N.
+
+config SCSI_UFS_DWC_40BIT_RMMI
+ bool "40-bit RMMI MPHY"
+ depends on SCSI_UFS_DWC_MPHY_TC
+ ---help---
+ This specifies that the Synopsys MPHY supports 40-bit RMMI operations.
+
+ Select this if you are using a 40-bit RMMI Synopsys MPHY.
+ If unsure, say N.
diff --git a/drivers/scsi/ufs/Makefile b/drivers/scsi/ufs/Makefile
index 8303bcc..5be2363 100644
--- a/drivers/scsi/ufs/Makefile
+++ b/drivers/scsi/ufs/Makefile
@@ -1,4 +1,6 @@
# UFSHCD makefile
+obj-$(CONFIG_SCSI_UFS_DWC_HOOKS) += ufshcd-dwc.o
+obj-$(CONFIG_SCSI_UFS_DWC_PLAT) += ufs-dwc.o
obj-$(CONFIG_SCSI_UFS_QCOM) += ufs-qcom.o
obj-$(CONFIG_SCSI_UFSHCD) += ufshcd.o
obj-$(CONFIG_SCSI_UFSHCD_PCI) += ufshcd-pci.o
diff --git a/drivers/scsi/ufs/ufs-dwc.c b/drivers/scsi/ufs/ufs-dwc.c
new file mode 100644
index 0000000..6582b9e
--- /dev/null
+++ b/drivers/scsi/ufs/ufs-dwc.c
@@ -0,0 +1,96 @@
+/*
+ * UFS Host driver for Synopsys Designware Core
+ *
+ * Copyright (C) 2015-2016 Synopsys, Inc. (www.synopsys.com)
+ *
+ * Authors: Joao Pinto <jpinto@...opsys.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/platform_device.h>
+#include <linux/of.h>
+#include <linux/delay.h>
+
+#include "ufshcd-pltfrm.h"
+#include "ufshcd-dwc.h"
+
+/**
+ * struct ufs_hba_dwc_vops - UFS DWC specific variant operations
+ *
+ */
+static struct ufs_hba_variant_ops ufs_dwc_hba_vops = {
+ .name = "dwc",
+ .custom_probe_hba = ufshcd_dwc_configuration,
+};
+
+/**
+ * ufs_dwc_probe()
+ * @pdev: pointer to platform device structure
+ *
+ */
+static int ufs_dwc_probe(struct platform_device *pdev)
+{
+ int err;
+ struct device *dev = &pdev->dev;
+
+ /* Perform generic probe */
+ err = ufshcd_pltfrm_init(pdev, &ufs_dwc_hba_vops);
+ if (err)
+ dev_err(dev, "ufshcd_pltfrm_init() failed %d\n", err);
+
+ return err;
+}
+
+/**
+ * ufs_dwc_remove()
+ * @pdev: pointer to platform device structure
+ *
+ */
+static int ufs_dwc_remove(struct platform_device *pdev)
+{
+ struct ufs_hba *hba = platform_get_drvdata(pdev);
+
+ pm_runtime_get_sync(&(pdev)->dev);
+ ufshcd_remove(hba);
+
+ return 0;
+}
+
+static const struct of_device_id ufs_dwc_match[] = {
+ {
+ .compatible = "snps,ufshcd"
+ },
+ { },
+};
+MODULE_DEVICE_TABLE(of, ufs_dwc_match);
+
+static const struct dev_pm_ops ufs_dwc_pm_ops = {
+ .suspend = ufshcd_pltfrm_suspend,
+ .resume = ufshcd_pltfrm_resume,
+ .runtime_suspend = ufshcd_pltfrm_runtime_suspend,
+ .runtime_resume = ufshcd_pltfrm_runtime_resume,
+ .runtime_idle = ufshcd_pltfrm_runtime_idle,
+};
+
+static struct platform_driver ufs_dwc_driver = {
+ .probe = ufs_dwc_probe,
+ .remove = ufs_dwc_remove,
+ .shutdown = ufshcd_pltfrm_shutdown,
+ .driver = {
+ .name = "ufshcd-dwc",
+ .pm = &ufs_dwc_pm_ops,
+ .of_match_table = of_match_ptr(ufs_dwc_match),
+ },
+};
+
+module_platform_driver(ufs_dwc_driver);
+
+MODULE_ALIAS("platform:ufshcd-dwc");
+MODULE_DESCRIPTION("DesignWare UFS Host platform glue driver");
+MODULE_AUTHOR("Joao Pinto <Joao.Pinto@...opsys.com>");
+MODULE_LICENSE("Dual BSD/GPL");
diff --git a/drivers/scsi/ufs/ufshcd-dwc.c b/drivers/scsi/ufs/ufshcd-dwc.c
new file mode 100644
index 0000000..b12b1a8
--- /dev/null
+++ b/drivers/scsi/ufs/ufshcd-dwc.c
@@ -0,0 +1,768 @@
+/*
+ * UFS Host driver for Synopsys Designware Core
+ *
+ * Copyright (C) 2015-2016 Synopsys, Inc. (www.synopsys.com)
+ *
+ * Authors: Joao Pinto <jpinto@...opsys.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include "ufshcd.h"
+#include "unipro.h"
+
+#include "ufshcd-dwc.h"
+#include "ufshci-dwc.h"
+
+/**
+ * ufshcd_dwc_program_clk_div()
+ * This function programs the clk divider value. This value is needed to
+ * provide 1 microsecond tick to unipro layer.
+ * @hba: Private Structure pointer
+ * @divider_val: clock divider value to be programmed
+ *
+ */
+void ufshcd_dwc_program_clk_div(struct ufs_hba *hba, u32 divider_val)
+{
+ ufshcd_writel(hba, divider_val, DWC_UFS_REG_HCLKDIV);
+}
+EXPORT_SYMBOL(ufshcd_dwc_program_clk_div);
+
+/**
+ * ufshcd_dwc_link_is_up()
+ * Check if link is up
+ * @hba: private structure poitner
+ *
+ * Returns 0 on success, non-zero value on failure
+ */
+int ufshcd_dwc_link_is_up(struct ufs_hba *hba)
+{
+ int dme_result = 0;
+
+ ufshcd_dme_get(hba, UIC_ARG_MIB(VS_POWERSTATE), &dme_result);
+
+ if (dme_result == UFSHCD_LINK_IS_UP) {
+ ufshcd_set_link_active(hba);
+ return 0;
+ }
+
+ return 1;
+}
+EXPORT_SYMBOL(ufshcd_dwc_link_is_up);
+
+/**
+ * ufshcd_dwc_connection_setup()
+ * This function configures both the local side (host) and the peer side
+ * (device) unipro attributes to establish the connection to application/
+ * cport.
+ * This function is not required if the hardware is properly configured to
+ * have this connection setup on reset. But invoking this function does no
+ * harm and should be fine even working with any ufs device.
+ *
+ * @hba: pointer to drivers private data
+ *
+ * Returns 0 on success non-zero value on failure
+ */
+int ufshcd_dwc_connection_setup(struct ufs_hba *hba)
+{
+ int ret = 0;
+
+ /* Local side Configuration */
+ ret = ufshcd_dme_set(hba, UIC_ARG_MIB(T_CONNECTIONSTATE), 0);
+ if (ret)
+ goto out;
+
+ ret = ufshcd_dme_set(hba, UIC_ARG_MIB(N_DEVICEID), 0);
+ if (ret)
+ goto out;
+
+ ret = ufshcd_dme_set(hba, UIC_ARG_MIB(N_DEVICEID_VALID), 0);
+ if (ret)
+ goto out;
+
+ ret = ufshcd_dme_set(hba, UIC_ARG_MIB(T_PEERDEVICEID), 1);
+ if (ret)
+ goto out;
+
+ ret = ufshcd_dme_set(hba, UIC_ARG_MIB(T_PEERCPORTID), 0);
+ if (ret)
+ goto out;
+
+ ret = ufshcd_dme_set(hba, UIC_ARG_MIB(T_TRAFFICCLASS), 0);
+ if (ret)
+ goto out;
+
+ ret = ufshcd_dme_set(hba, UIC_ARG_MIB(T_CPORTFLAGS), 0x6);
+ if (ret)
+ goto out;
+
+ ret = ufshcd_dme_set(hba, UIC_ARG_MIB(T_CPORTMODE), 1);
+ if (ret)
+ goto out;
+
+ ret = ufshcd_dme_set(hba, UIC_ARG_MIB(T_CONNECTIONSTATE), 1);
+ if (ret)
+ goto out;
+
+
+ /* Peer side Configuration */
+ ret = ufshcd_dme_peer_set(hba, UIC_ARG_MIB(T_CONNECTIONSTATE), 0);
+ if (ret)
+ goto out;
+
+ ret = ufshcd_dme_peer_set(hba, UIC_ARG_MIB(N_DEVICEID), 1);
+ if (ret)
+ goto out;
+
+ ret = ufshcd_dme_peer_set(hba, UIC_ARG_MIB(N_DEVICEID_VALID), 1);
+ if (ret)
+ goto out;
+
+ ret = ufshcd_dme_peer_set(hba, UIC_ARG_MIB(T_PEERDEVICEID), 1);
+ if (ret)
+ goto out;
+
+ ret = ufshcd_dme_peer_set(hba, UIC_ARG_MIB(T_PEERCPORTID), 0);
+ if (ret)
+ goto out;
+
+ ret = ufshcd_dme_peer_set(hba, UIC_ARG_MIB(T_TRAFFICCLASS), 0);
+ if (ret)
+ goto out;
+
+ ret = ufshcd_dme_peer_set(hba, UIC_ARG_MIB(T_CPORTFLAGS), 0x6);
+ if (ret)
+ goto out;
+
+ ret = ufshcd_dme_peer_set(hba, UIC_ARG_MIB(T_CPORTMODE), 1);
+ if (ret)
+ goto out;
+
+ ret = ufshcd_dme_peer_set(hba, UIC_ARG_MIB(T_CONNECTIONSTATE), 1);
+ if (ret)
+ goto out;
+
+out:
+ return ret;
+}
+
+/**
+ * ufshcd_dwc_setup_20bit_rmmi_lane0()
+ * This function configures Synopsys MPHY 20-bit RMMI Lane 0
+ * @hba: Pointer to drivers structure
+ *
+ * Returns 0 on success or non-zero value on failure
+ */
+int ufshcd_dwc_setup_20bit_rmmi_lane0(struct ufs_hba *hba)
+{
+ int ret = 0;
+
+ /* TX Reference Clock 26MHz */
+ ret = ufshcd_dme_set(hba, UIC_ARG_MIB_SEL(TX_REFCLKFREQ,
+ SELIND_LN0_TX), 0x01);
+ if (ret)
+ goto out;
+
+ /* TX Configuration Clock Frequency Val; Divider setting */
+ ret = ufshcd_dme_set(hba, UIC_ARG_MIB_SEL(TX_CFGCLKFREQVAL,
+ SELIND_LN0_TX), 0x19);
+ if (ret)
+ goto out;
+
+ /* RX Configuration Clock Frequency Val; Divider setting */
+ ret = ufshcd_dme_set(hba, UIC_ARG_MIB_SEL(RX_CFGCLKFREQVAL,
+ SELIND_LN0_RX), 0x19);
+ if (ret)
+ goto out;
+
+ /* TX 20-bit RMMI Interface */
+ ret = ufshcd_dme_set(hba, UIC_ARG_MIB_SEL(CFGEXTRATTR,
+ SELIND_LN0_TX), 0x12);
+ if (ret)
+ goto out;
+
+ /* TX dither configuration */
+ ret = ufshcd_dme_set(hba, UIC_ARG_MIB_SEL(DITHERCTRL2,
+ SELIND_LN0_TX), 0xd6);
+ if (ret)
+ goto out;
+
+ /* RX Reference Clock 26MHz */
+ ret = ufshcd_dme_set(hba, UIC_ARG_MIB_SEL(RX_REFCLKFREQ,
+ SELIND_LN0_RX), 0x01);
+ if (ret)
+ goto out;
+
+ /* RX 20-bit RMMI Interface */
+ ret = ufshcd_dme_set(hba, UIC_ARG_MIB_SEL(CFGWIDEINLN,
+ SELIND_LN0_RX), 2);
+ if (ret)
+ goto out;
+
+ /* RX Squelch Detector output is routed to RX hibern8 exit signal */
+ ret = ufshcd_dme_set(hba, UIC_ARG_MIB_SEL(CFGRXCDR8,
+ SELIND_LN0_RX), 0x80);
+ if (ret)
+ goto out;
+
+ /* Common block Direct Control 10 */
+ ret = ufshcd_dme_set(hba, UIC_ARG_MIB(DIRECTCTRL10), 0x04);
+ if (ret)
+ goto out;
+
+ /* Common block Direct Control 19 */
+ ret = ufshcd_dme_set(hba, UIC_ARG_MIB(DIRECTCTRL19), 0x02);
+ if (ret)
+ goto out;
+
+ /* ENARXDIRECTCFG4 */
+ ret = ufshcd_dme_set(hba, UIC_ARG_MIB_SEL(ENARXDIRECTCFG4,
+ SELIND_LN0_RX), 0x03);
+ if (ret)
+ goto out;
+
+ /* CFGRXOVR8 */
+ ret = ufshcd_dme_set(hba, UIC_ARG_MIB_SEL(CFGRXOVR8,
+ SELIND_LN0_RX), 0x16);
+ if (ret)
+ goto out;
+
+ /* RXDIRECTCTRL2 */
+ ret = ufshcd_dme_set(hba, UIC_ARG_MIB_SEL(RXDIRECTCTRL2,
+ SELIND_LN0_RX), 0x42);
+
+ if (ret)
+ goto out;
+
+ /* ENARXDIRECTCFG3 */
+ ret = ufshcd_dme_set(hba, UIC_ARG_MIB_SEL(ENARXDIRECTCFG3,
+ SELIND_LN0_RX), 0xa4);
+
+ if (ret)
+ goto out;
+
+ /* RXCALCTRL */
+ ret = ufshcd_dme_set(hba, UIC_ARG_MIB_SEL(RXCALCTRL,
+ SELIND_LN0_RX), 0x01);
+ if (ret)
+ goto out;
+
+ /* ENARXDIRECTCFG2 */
+ ret = ufshcd_dme_set(hba, UIC_ARG_MIB_SEL(ENARXDIRECTCFG2,
+ SELIND_LN0_RX), 0x01);
+ if (ret)
+ goto out;
+
+ /* CFGOVR4 */
+ ret = ufshcd_dme_set(hba, UIC_ARG_MIB_SEL(CFGRXOVR4,
+ SELIND_LN0_RX), 0x28);
+ if (ret)
+ goto out;
+
+ /* RXSQCTRL */
+ ret = ufshcd_dme_set(hba, UIC_ARG_MIB_SEL(RXSQCTRL,
+ SELIND_LN0_RX), 0x1E);
+ if (ret)
+ goto out;
+
+ /* CFGOVR6 */
+ ret = ufshcd_dme_set(hba, UIC_ARG_MIB_SEL(CFGRXOVR6,
+ SELIND_LN0_RX), 0x2f);
+ if (ret)
+ goto out;
+
+ /* CBPRGPLL2 */
+ ret = ufshcd_dme_set(hba, UIC_ARG_MIB(CBPRGPLL2), 0x00);
+
+out:
+ return ret;
+}
+
+/**
+ * ufshcd_dwc_setup_20bit_rmmi_lane1()
+ * This function configures Synopsys MPHY 20-bit RMMI Lane 1
+ * @hba: Pointer to drivers structure
+ *
+ * Returns 0 on success or non-zero value on failure
+ */
+int ufshcd_dwc_setup_20bit_rmmi_lane1(struct ufs_hba *hba)
+{
+ int connected_rx_lanes = 0;
+ int connected_tx_lanes = 0;
+ int ret = 0;
+
+ /* Get the available lane count */
+ ufshcd_dme_get(hba, UIC_ARG_MIB(PA_CONNECTEDRXDATALANES),
+ &connected_rx_lanes);
+ ufshcd_dme_get(hba, UIC_ARG_MIB(PA_CONNECTEDTXDATALANES),
+ &connected_tx_lanes);
+
+ if (connected_tx_lanes == 2) {
+
+ /* TX Reference Clock 26MHz */
+ ret = ufshcd_dme_set(hba, UIC_ARG_MIB_SEL(TX_REFCLKFREQ,
+ SELIND_LN1_TX), 0x0d);
+ if (ret)
+ goto out;
+
+ /* TX Configuration Clock Frequency Val; Divider setting */
+ ret = ufshcd_dme_set(hba, UIC_ARG_MIB_SEL(TX_CFGCLKFREQVAL,
+ SELIND_LN1_TX), 0x19);
+ if (ret)
+ goto out;
+
+ /* TX 20-bit RMMI Interface */
+ ret = ufshcd_dme_set(hba, UIC_ARG_MIB_SEL(CFGEXTRATTR,
+ SELIND_LN1_TX), 0x12);
+ if (ret)
+ goto out;
+
+ /* TX dither configuration */
+ ret = ufshcd_dme_set(hba, UIC_ARG_MIB_SEL(DITHERCTRL2,
+ SELIND_LN0_TX), 0xd6);
+ if (ret)
+ goto out;
+ }
+
+ if (connected_rx_lanes == 2) {
+
+ /* RX Reference Clock 26MHz */
+ ret = ufshcd_dme_set(hba, UIC_ARG_MIB_SEL(RX_REFCLKFREQ,
+ SELIND_LN1_RX), 0x01);
+ if (ret)
+ goto out;
+
+ /* RX Configuration Clock Frequency Val; Divider setting */
+ ret = ufshcd_dme_set(hba, UIC_ARG_MIB_SEL(RX_CFGCLKFREQVAL,
+ SELIND_LN1_RX), 0x19);
+ if (ret)
+ goto out;
+
+ /* RX 20-bit RMMI Interface */
+ ret = ufshcd_dme_set(hba, UIC_ARG_MIB_SEL(CFGWIDEINLN,
+ SELIND_LN1_RX), 2);
+ if (ret)
+ goto out;
+
+ /* RX Squelch Detector output is routed to RX hibern8 exit
+ * signal
+ */
+ ret = ufshcd_dme_set(hba, UIC_ARG_MIB_SEL(CFGRXCDR8,
+ SELIND_LN1_RX), 0x80);
+ if (ret)
+ goto out;
+
+ /* ENARXDIRECTCFG4 */
+ ret = ufshcd_dme_set(hba, UIC_ARG_MIB_SEL(ENARXDIRECTCFG4,
+ SELIND_LN1_RX), 0x03);
+ if (ret)
+ goto out;
+
+ /* CFGRXOVR8 */
+ ret = ufshcd_dme_set(hba, UIC_ARG_MIB_SEL(CFGRXOVR8,
+ SELIND_LN1_RX), 0x16);
+ if (ret)
+ goto out;
+
+ /* RXDIRECTCTRL2 */
+ ret = ufshcd_dme_set(hba, UIC_ARG_MIB_SEL(RXDIRECTCTRL2,
+ SELIND_LN1_RX), 0x42);
+ if (ret)
+ goto out;
+
+ /* ENARXDIRECTCFG3 */
+ ret = ufshcd_dme_set(hba, UIC_ARG_MIB_SEL(ENARXDIRECTCFG3,
+ SELIND_LN1_RX), 0xa4);
+ if (ret)
+ goto out;
+
+ /* RXCALCTRL */
+ ret = ufshcd_dme_set(hba, UIC_ARG_MIB_SEL(RXCALCTRL,
+ SELIND_LN1_RX), 0x01);
+ if (ret)
+ goto out;
+
+ /* ENARXDIRECTCFG2 */
+ ret = ufshcd_dme_set(hba, UIC_ARG_MIB_SEL(ENARXDIRECTCFG2,
+ SELIND_LN1_RX), 0x01);
+ if (ret)
+ goto out;
+
+ /* CFGOVR4 */
+ ret = ufshcd_dme_set(hba, UIC_ARG_MIB_SEL(CFGRXOVR4,
+ SELIND_LN1_RX), 0x28);
+ if (ret)
+ goto out;
+
+ /* RXSQCTRL */
+ ret = ufshcd_dme_set(hba, UIC_ARG_MIB_SEL(RXSQCTRL,
+ SELIND_LN1_RX), 0x1E);
+ if (ret)
+ goto out;
+
+ /* CFGOVR6 */
+ ret = ufshcd_dme_set(hba, UIC_ARG_MIB_SEL(CFGRXOVR6,
+ SELIND_LN1_RX), 0x2f);
+ if (ret)
+ goto out;
+ }
+
+out:
+ return ret;
+}
+
+/**
+ * ufshcd_dwc_setup_20bit_rmmi()
+ * This function configures Synopsys MPHY specific atributes (20-bit RMMI)
+ * @hba: Pointer to drivers structure
+ *
+ * Returns 0 on success or non-zero value on failure
+ */
+int ufshcd_dwc_setup_20bit_rmmi(struct ufs_hba *hba)
+{
+ int ret = 0;
+
+ /* Common block Tx Global Hibernate Exit */
+ ret = ufshcd_dme_set(hba, UIC_ARG_MIB(TX_GLOBALHIBERNATE), 0x00);
+ if (ret)
+ goto out;
+
+ /* Common block Reference Clock Mode 26MHz */
+ ret = ufshcd_dme_set(hba, UIC_ARG_MIB(REFCLKMODE), 0x01);
+ if (ret)
+ goto out;
+
+ /* Common block DCO Target Frequency MAX PWM G1:9Mpbs */
+ ret = ufshcd_dme_set(hba, UIC_ARG_MIB(CDIRECTCTRL6), 0xc0);
+ if (ret)
+ goto out;
+
+ /* Common block TX and RX Div Factor is 4 7Mbps/20 = 350KHz */
+ ret = ufshcd_dme_set(hba, UIC_ARG_MIB(CBDIVFACTOR), 0x44);
+ if (ret)
+ goto out;
+
+ /* Common Block DC0 Ctrl 5*/
+ ret = ufshcd_dme_set(hba, UIC_ARG_MIB(CBDCOCTRL5), 0x64);
+ if (ret)
+ goto out;
+
+ /* Common Block Program Tunning*/
+ ret = ufshcd_dme_set(hba, UIC_ARG_MIB(CBPRGTUNING), 0x09);
+ if (ret)
+ goto out;
+
+ /* Common Block Real Time Observe Select - for debugging */
+ ret = ufshcd_dme_set(hba, UIC_ARG_MIB(RTOBSERVESELECT), 0x00);
+ if (ret)
+ goto out;
+
+ /* Lane 0 configuration*/
+ ret = ufshcd_dwc_setup_20bit_rmmi_lane0(hba);
+ if (ret)
+ goto out;
+
+ /* Lane 1 configuration*/
+ ret = ufshcd_dwc_setup_20bit_rmmi_lane1(hba);
+ if (ret)
+ goto out;
+
+out:
+ return ret;
+}
+
+/**
+ * ufshcd_dwc_setup_40bit_rmmi()
+ * This function configures Synopsys MPHY specific atributes (40-bit RMMI)
+ * @hba: Pointer to drivers structure
+ *
+ * Returns 0 on success or non-zero value on failure
+ */
+int ufshcd_dwc_setup_40bit_rmmi(struct ufs_hba *hba)
+{
+ int ret = 0;
+
+ /* Common block Tx Global Hibernate Exit */
+ ret = ufshcd_dme_set(hba, UIC_ARG_MIB(TX_GLOBALHIBERNATE), 0x00);
+ if (ret)
+ goto out;
+
+ /* Common block Reference Clock Mode 26MHz */
+ ret = ufshcd_dme_set(hba, UIC_ARG_MIB(REFCLKMODE), 0x01);
+ if (ret)
+ goto out;
+
+ /* Common block DCO Target Frequency MAX PWM G1:7Mpbs */
+ ret = ufshcd_dme_set(hba, UIC_ARG_MIB(CDIRECTCTRL6), 0x80);
+ if (ret)
+ goto out;
+
+ /* Common block TX and RX Div Factor is 4 7Mbps/40 = 175KHz */
+ ret = ufshcd_dme_set(hba, UIC_ARG_MIB(CBDIVFACTOR), 0x08);
+ if (ret)
+ goto out;
+
+ /* Common Block DC0 Ctrl 5*/
+ ret = ufshcd_dme_set(hba, UIC_ARG_MIB(CBDCOCTRL5), 0x64);
+ if (ret)
+ goto out;
+
+ /* Common Block Program Tunning*/
+ ret = ufshcd_dme_set(hba, UIC_ARG_MIB(CBPRGTUNING), 0x09);
+ if (ret)
+ goto out;
+
+ /* Common Block Real Time Observe Select - for debugging */
+ ret = ufshcd_dme_set(hba, UIC_ARG_MIB(RTOBSERVESELECT), 0x00);
+ if (ret)
+ goto out;
+
+ /* Lane 0 configuration*/
+
+ /* TX Reference Clock 26MHz */
+ ret = ufshcd_dme_set(hba, UIC_ARG_MIB_SEL(TX_REFCLKFREQ,
+ SELIND_LN0_TX), 0x01);
+ if (ret)
+ goto out;
+
+ /* TX Configuration Clock Frequency Val; Divider setting */
+ ret = ufshcd_dme_set(hba, UIC_ARG_MIB_SEL(TX_CFGCLKFREQVAL,
+ SELIND_LN0_TX), 0x19);
+ if (ret)
+ goto out;
+
+ /* TX 40-bit RMMI Interface */
+ ret = ufshcd_dme_set(hba, UIC_ARG_MIB_SEL(CFGEXTRATTR,
+ SELIND_LN0_TX), 0x14);
+ if (ret)
+ goto out;
+
+ /* TX dither configuration */
+ ret = ufshcd_dme_set(hba, UIC_ARG_MIB_SEL(DITHERCTRL2,
+ SELIND_LN0_TX), 0xd6);
+ if (ret)
+ goto out;
+
+ /* RX Reference Clock 26MHz */
+ ret = ufshcd_dme_set(hba, UIC_ARG_MIB_SEL(RX_REFCLKFREQ,
+ SELIND_LN0_RX), 0x01);
+ if (ret)
+ goto out;
+
+ /* RX Configuration Clock Frequency Val; Divider setting */
+ ret = ufshcd_dme_set(hba, UIC_ARG_MIB_SEL(RX_CFGCLKFREQVAL,
+ SELIND_LN0_RX), 0x19);
+ if (ret)
+ goto out;
+
+ /* RX 40-bit RMMI Interface */
+ ret = ufshcd_dme_set(hba, UIC_ARG_MIB_SEL(CFGWIDEINLN,
+ SELIND_LN0_RX), 4);
+ if (ret)
+ goto out;
+
+ /* RX Squelch Detector output is routed to RX hibern8 exit signal */
+ ret = ufshcd_dme_set(hba, UIC_ARG_MIB_SEL(CFGRXCDR8,
+ SELIND_LN0_RX), 0x80);
+ if (ret)
+ goto out;
+
+ /* RX Squelch Detector output is routed to RX hibern8 exit signal */
+ ret = ufshcd_dme_set(hba, UIC_ARG_MIB_SEL(CFGRXCDR8,
+ SELIND_LN0_RX), 0x80);
+ if (ret)
+ goto out;
+
+ /* Common block Direct Control 10 */
+ ret = ufshcd_dme_set(hba, UIC_ARG_MIB(DIRECTCTRL10), 0x04);
+ if (ret)
+ goto out;
+
+ /* Common block Direct Control 19 */
+ ret = ufshcd_dme_set(hba, UIC_ARG_MIB(DIRECTCTRL19), 0x02);
+ if (ret)
+ goto out;
+
+ /* RX Squelch Detector output is routed to RX hibern8 exit signal */
+ ret = ufshcd_dme_set(hba, UIC_ARG_MIB_SEL(CFGRXCDR8,
+ SELIND_LN0_RX), 0x80);
+ if (ret)
+ goto out;
+
+ /* ENARXDIRECTCFG4 */
+ ret = ufshcd_dme_set(hba, UIC_ARG_MIB_SEL(ENARXDIRECTCFG4,
+ SELIND_LN0_RX), 0x03);
+ if (ret)
+ goto out;
+
+ /* CFGRXOVR8 */
+ ret = ufshcd_dme_set(hba, UIC_ARG_MIB_SEL(CFGRXOVR8,
+ SELIND_LN0_RX), 0x16);
+ if (ret)
+ goto out;
+
+ /* RXDIRECTCTRL2 */
+ ret = ufshcd_dme_set(hba, UIC_ARG_MIB_SEL(RXDIRECTCTRL2,
+ SELIND_LN0_RX), 0x42);
+ if (ret)
+ goto out;
+
+ /* ENARXDIRECTCFG3 */
+ ret = ufshcd_dme_set(hba, UIC_ARG_MIB_SEL(ENARXDIRECTCFG3,
+ SELIND_LN0_RX), 0xa4);
+ if (ret)
+ goto out;
+
+ /* RXCALCTRL */
+ ret = ufshcd_dme_set(hba, UIC_ARG_MIB_SEL(RXCALCTRL,
+ SELIND_LN0_RX), 0x01);
+ if (ret)
+ goto out;
+
+ /* ENARXDIRECTCFG2 */
+ ret = ufshcd_dme_set(hba, UIC_ARG_MIB_SEL(ENARXDIRECTCFG2,
+ SELIND_LN0_RX), 0x01);
+ if (ret)
+ goto out;
+
+ /* CFGOVR4 */
+ ret = ufshcd_dme_set(hba, UIC_ARG_MIB_SEL(CFGRXOVR4,
+ SELIND_LN0_RX), 0x28);
+ if (ret)
+ goto out;
+
+ /* RXSQCTRL */
+ ret = ufshcd_dme_set(hba, UIC_ARG_MIB_SEL(RXSQCTRL,
+ SELIND_LN0_RX), 0x1E);
+ if (ret)
+ goto out;
+
+ /* CFGOVR6 */
+ ret = ufshcd_dme_set(hba, UIC_ARG_MIB_SEL(CFGRXOVR6,
+ SELIND_LN0_RX), 0x2f);
+ if (ret)
+ goto out;
+
+ /* CBPRGPLL2 */
+ ret = ufshcd_dme_set(hba, UIC_ARG_MIB(CBPRGPLL2), 0x00);
+ if (ret)
+ goto out;
+
+out:
+ return ret;
+}
+
+/**
+ * ufshcd_dwc_setup_mphy()
+ * This function configures Local (host) Synopsys MPHY specific attributes
+ *
+ * @hba: Pointer to drivers structure
+ *
+ * Returns 0 on success non-zero value on failure
+ */
+int ufshcd_dwc_setup_mphy(struct ufs_hba *hba)
+{
+ int ret = 0;
+
+#ifdef CONFIG_SCSI_UFS_DWC_40BIT_RMMI
+ dev_info(hba->dev, "Configuring MPHY 40-bit RMMI");
+ ret = ufshcd_dwc_setup_40bit_rmmi(hba);
+ if (ret) {
+ dev_err(hba->dev, "40-bit RMMI configuration failed");
+ goto out;
+ }
+#else
+#ifdef CONFIG_SCSI_UFS_DWC_20BIT_RMMI
+ dev_info(hba->dev, "Configuring MPHY 20-bit RMMI");
+ ret = ufshcd_dwc_setup_20bit_rmmi(hba);
+ if (ret) {
+ dev_err(hba->dev, "20-bit RMMI configuration failed");
+ goto out;
+ }
+#endif
+#endif
+ /* To write Shadow register bank to effective configuration block */
+ ret = ufshcd_dme_set(hba, UIC_ARG_MIB(VS_MPHYCFGUPDT), 0x01);
+ if (ret)
+ goto out;
+
+ /* To configure Debug OMC */
+ ret = ufshcd_dme_set(hba, UIC_ARG_MIB(VS_DEBUGOMC), 0x01);
+
+out:
+ return ret;
+}
+
+/**
+ * ufshcd_dwc_configuration()
+ * UFS Host DWC specific configuration
+ * @hba: private structure poitner
+ *
+ * Returns 0 on success, non-zero value on failure
+ */
+int ufshcd_dwc_configuration(struct ufs_hba *hba)
+{
+ int ret = 0;
+
+ /* Program Clock Divider Value */
+ ufshcd_dwc_program_clk_div(hba, UFSHCD_CLK_DIV_125);
+
+#ifdef CONFIG_SCSI_UFS_DWC_MPHY_TC
+ ret = ufshcd_dwc_setup_mphy(hba);
+ if (ret) {
+ dev_err(hba->dev, "MPHY configuration failed (%d)", ret);
+ goto out;
+ }
+#endif
+ ret = ufshcd_dme_link_startup(hba);
+ if (ret) {
+ dev_err(hba->dev, "Link Startup command failed (%d)", ret);
+ goto out;
+ }
+
+ ret = ufshcd_dwc_link_is_up(hba);
+ if (ret) {
+ dev_err(hba->dev, "Link is not up");
+ goto out;
+ }
+
+ ret = ufshcd_dwc_connection_setup(hba);
+ if (ret) {
+ dev_err(hba->dev, "Connection setup failed (%d)", ret);
+ goto out;
+ }
+
+ ret = ufshcd_make_hba_operational(hba);
+ if (ret) {
+ dev_err(hba->dev, "HBA kick start failed (%d)", ret);
+ goto out;
+ }
+
+ ret = ufshcd_verify_dev_init(hba);
+ if (ret) {
+ dev_err(hba->dev, "Device init failed (%d)", ret);
+ goto out;
+ }
+
+ ret = ufshcd_complete_dev_init(hba);
+ if (ret) {
+ dev_err(hba->dev, "Device final init failed (%d)", ret);
+ goto out;
+ }
+
+ ufshcd_set_ufs_dev_active(hba);
+ hba->wlun_dev_clr_ua = false;
+
+ if (hba->ufshcd_state == UFSHCD_STATE_RESET)
+ scsi_unblock_requests(hba->host);
+
+ hba->ufshcd_state = UFSHCD_STATE_OPERATIONAL;
+
+ scsi_scan_host(hba->host);
+
+out:
+ return ret;
+}
+EXPORT_SYMBOL(ufshcd_dwc_configuration);
diff --git a/drivers/scsi/ufs/ufshcd-dwc.h b/drivers/scsi/ufs/ufshcd-dwc.h
new file mode 100644
index 0000000..dce03ad
--- /dev/null
+++ b/drivers/scsi/ufs/ufshcd-dwc.h
@@ -0,0 +1,26 @@
+/*
+ * UFS Host driver for Synopsys Designware Core
+ *
+ * Copyright (C) 2015-2016 Synopsys, Inc. (www.synopsys.com)
+ *
+ * Authors: Joao Pinto <jpinto@...opsys.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#ifndef _UFSHCD_DWC_H
+#define _UFSHCD_DWC_H
+
+void ufshcd_dwc_program_clk_div(struct ufs_hba *hba, u32);
+int ufshcd_dwc_link_is_up(struct ufs_hba *hba);
+int ufshcd_dwc_connection_setup(struct ufs_hba *hba);
+int ufshcd_dwc_setup_20bit_rmmi_lane0(struct ufs_hba *hba);
+int ufshcd_dwc_setup_20bit_rmmi_lane1(struct ufs_hba *hba);
+int ufshcd_dwc_setup_20bit_rmmi(struct ufs_hba *hba);
+int ufshcd_dwc_setup_40bit_rmmi(struct ufs_hba *hba);
+int ufshcd_dwc_setup_mphy(struct ufs_hba *hba);
+int ufshcd_dwc_configuration(struct ufs_hba *hba);
+
+#endif /* End of Header */
diff --git a/drivers/scsi/ufs/ufshcd-pci.c b/drivers/scsi/ufs/ufshcd-pci.c
index d15eaa4..66518a1 100644
--- a/drivers/scsi/ufs/ufshcd-pci.c
+++ b/drivers/scsi/ufs/ufshcd-pci.c
@@ -34,6 +34,9 @@
*/
#include "ufshcd.h"
+#ifdef CONFIG_SCSI_UFS_DWC_HOOKS
+#include "ufshcd-dwc.h"
+#endif
#include <linux/pci.h>
#include <linux/pm_runtime.h>
@@ -83,6 +86,16 @@ static int ufshcd_pci_runtime_idle(struct device *dev)
#define ufshcd_pci_runtime_idle NULL
#endif /* CONFIG_PM */
+#ifdef CONFIG_SCSI_UFS_DWC_HOOKS
+/**
+ * struct ufs_hba_dwc_vops - UFS DWC specific variant operations
+ */
+static struct ufs_hba_variant_ops ufs_dwc_pci_hba_vops = {
+ .name = "dwc-pci",
+ .custom_probe_hba = ufshcd_dwc_configuration,
+};
+#endif
+
/**
* ufshcd_pci_shutdown - main function to put the controller in reset state
* @pdev: pointer to PCI device handle
@@ -144,6 +157,9 @@ ufshcd_pci_probe(struct pci_dev *pdev, const struct pci_device_id *id)
INIT_LIST_HEAD(&hba->clk_list_head);
+#ifdef CONFIG_SCSI_UFS_DWC_HOOKS
+ hba->vops = &ufs_dwc_pci_hba_vops;
+#endif
err = ufshcd_init(hba, mmio_base, pdev->irq);
if (err) {
dev_err(&pdev->dev, "Initialization failed\n");
@@ -167,6 +183,10 @@ static const struct dev_pm_ops ufshcd_pci_pm_ops = {
static const struct pci_device_id ufshcd_pci_tbl[] = {
{ PCI_VENDOR_ID_SAMSUNG, 0xC00C, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 0 },
+#ifdef CONFIG_SCSI_UFS_DWC_HOOKS
+ { PCI_VENDOR_ID_SYNOPSYS, 0xB101, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 0 },
+ { PCI_VENDOR_ID_SYNOPSYS, 0xB102, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 0 },
+#endif
{ } /* terminate list */
};
diff --git a/drivers/scsi/ufs/ufshcd.c b/drivers/scsi/ufs/ufshcd.c
index 2b5f2bf..c16181f 100644
--- a/drivers/scsi/ufs/ufshcd.c
+++ b/drivers/scsi/ufs/ufshcd.c
@@ -104,13 +104,6 @@ enum {
UFSHCD_CAN_QUEUE = 32,
};
-/* UFSHCD states */
-enum {
- UFSHCD_STATE_RESET,
- UFSHCD_STATE_ERROR,
- UFSHCD_STATE_OPERATIONAL,
-};
-
/* UFSHCD error handling flags */
enum {
UFSHCD_EH_IN_PROGRESS = (1 << 0),
@@ -138,8 +131,6 @@ enum {
#define ufshcd_clear_eh_in_progress(h) \
(h->eh_flags &= ~UFSHCD_EH_IN_PROGRESS)
-#define ufshcd_set_ufs_dev_active(h) \
- ((h)->curr_dev_pwr_mode = UFS_ACTIVE_PWR_MODE)
#define ufshcd_set_ufs_dev_sleep(h) \
((h)->curr_dev_pwr_mode = UFS_SLEEP_PWR_MODE)
#define ufshcd_set_ufs_dev_poweroff(h) \
@@ -2083,7 +2074,7 @@ static void ufshcd_host_memory_configure(struct ufs_hba *hba)
*
* Returns 0 on success, non-zero value on failure
*/
-static int ufshcd_dme_link_startup(struct ufs_hba *hba)
+int ufshcd_dme_link_startup(struct ufs_hba *hba)
{
struct uic_command uic_cmd = {0};
int ret;
@@ -2096,6 +2087,7 @@ static int ufshcd_dme_link_startup(struct ufs_hba *hba)
"dme-link-startup: error code %d\n", ret);
return ret;
}
+EXPORT_SYMBOL_GPL(ufshcd_dme_link_startup);
static inline void ufshcd_add_delay_before_dme_cmd(struct ufs_hba *hba)
{
@@ -2531,7 +2523,7 @@ static int ufshcd_config_pwr_mode(struct ufs_hba *hba,
*
* Set fDeviceInit flag and poll until device toggles it.
*/
-static int ufshcd_complete_dev_init(struct ufs_hba *hba)
+int ufshcd_complete_dev_init(struct ufs_hba *hba)
{
int i, retries, err = 0;
bool flag_res = 1;
@@ -2575,6 +2567,7 @@ static int ufshcd_complete_dev_init(struct ufs_hba *hba)
out:
return err;
}
+EXPORT_SYMBOL_GPL(ufshcd_complete_dev_init);
/**
* ufshcd_make_hba_operational - Make UFS controller operational
@@ -2588,7 +2581,7 @@ out:
*
* Returns 0 on success, non-zero value on failure
*/
-static int ufshcd_make_hba_operational(struct ufs_hba *hba)
+int ufshcd_make_hba_operational(struct ufs_hba *hba)
{
int err = 0;
u32 reg;
@@ -2629,6 +2622,7 @@ static int ufshcd_make_hba_operational(struct ufs_hba *hba)
out:
return err;
}
+EXPORT_SYMBOL_GPL(ufshcd_make_hba_operational);
/**
* ufshcd_hba_enable - initialize the controller
@@ -2804,7 +2798,7 @@ out:
* not respond with NOP IN UPIU within timeout of %NOP_OUT_TIMEOUT
* and we retry sending NOP OUT for %NOP_OUT_RETRIES iterations.
*/
-static int ufshcd_verify_dev_init(struct ufs_hba *hba)
+int ufshcd_verify_dev_init(struct ufs_hba *hba)
{
int err = 0;
int retries;
@@ -2827,6 +2821,7 @@ static int ufshcd_verify_dev_init(struct ufs_hba *hba)
dev_err(hba->dev, "%s: NOP OUT failed %d\n", __func__, err);
return err;
}
+EXPORT_SYMBOL_GPL(ufshcd_verify_dev_init);
/**
* ufshcd_set_queue_depth - set lun queue depth
@@ -5666,7 +5661,16 @@ int ufshcd_init(struct ufs_hba *hba, void __iomem *mmio_base, unsigned int irq)
*/
ufshcd_set_ufs_dev_poweroff(hba);
- async_schedule(ufshcd_async_scan, hba);
+ /* Hook for specific hardware config initialization */
+ if (hba->vops->custom_probe_hba) {
+ err = ufshcd_vops_custom_probe_hba(hba);
+ if (err) {
+ dev_err(hba->dev, "Host controller config failed\n");
+ goto out_remove_scsi_host;
+ }
+ }
+ else
+ async_schedule(ufshcd_async_scan, hba);
return 0;
diff --git a/drivers/scsi/ufs/ufshcd.h b/drivers/scsi/ufs/ufshcd.h
index 2570d94..3f12616 100644
--- a/drivers/scsi/ufs/ufshcd.h
+++ b/drivers/scsi/ufs/ufshcd.h
@@ -76,6 +76,13 @@ enum dev_cmd_type {
DEV_CMD_TYPE_QUERY = 0x1,
};
+/* UFSHCD states */
+enum {
+ UFSHCD_STATE_RESET,
+ UFSHCD_STATE_ERROR,
+ UFSHCD_STATE_OPERATIONAL,
+};
+
/**
* struct uic_command - UIC command structure
* @command: UIC command
@@ -124,6 +131,8 @@ enum uic_link_state {
UIC_LINK_ACTIVE_STATE)
#define ufshcd_set_link_hibern8(hba) ((hba)->uic_link_state = \
UIC_LINK_HIBERN8_STATE)
+#define ufshcd_set_ufs_dev_active(h) \
+ ((h)->curr_dev_pwr_mode = UFS_ACTIVE_PWR_MODE)
/*
* UFS Power management levels.
@@ -283,6 +292,7 @@ struct ufs_hba_variant_ops {
int (*suspend)(struct ufs_hba *, enum ufs_pm_op);
int (*resume)(struct ufs_hba *, enum ufs_pm_op);
void (*dbg_register_dump)(struct ufs_hba *hba);
+ int (*custom_probe_hba)(struct ufs_hba *hba);
};
/* clock gating state */
@@ -634,6 +644,10 @@ extern int ufshcd_dme_set_attr(struct ufs_hba *hba, u32 attr_sel,
u8 attr_set, u32 mib_val, u8 peer);
extern int ufshcd_dme_get_attr(struct ufs_hba *hba, u32 attr_sel,
u32 *mib_val, u8 peer);
+int ufshcd_dme_link_startup(struct ufs_hba *hba);
+int ufshcd_make_hba_operational(struct ufs_hba *hba);
+int ufshcd_verify_dev_init(struct ufs_hba *hba);
+int ufshcd_complete_dev_init(struct ufs_hba *hba);
/* UIC command interfaces for DME primitives */
#define DME_LOCAL 0
@@ -788,4 +802,12 @@ static inline void ufshcd_vops_dbg_register_dump(struct ufs_hba *hba)
hba->vops->dbg_register_dump(hba);
}
+static inline int ufshcd_vops_custom_probe_hba(struct ufs_hba *hba)
+{
+ if (hba->vops && hba->vops->custom_probe_hba)
+ return hba->vops->custom_probe_hba(hba);
+
+ return 0;
+}
+
#endif /* End of Header */
diff --git a/drivers/scsi/ufs/ufshci-dwc.h b/drivers/scsi/ufs/ufshci-dwc.h
new file mode 100644
index 0000000..08ae0ef
--- /dev/null
+++ b/drivers/scsi/ufs/ufshci-dwc.h
@@ -0,0 +1,42 @@
+/*
+ * UFS Host driver for Synopsys Designware Core
+ *
+ * Copyright (C) 2015-2016 Synopsys, Inc. (www.synopsys.com)
+ *
+ * Authors: Joao Pinto <jpinto@...opsys.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#ifndef _UFSHCI_DWC_H
+#define _UFSHCI_DWC_H
+
+/* DWC HC UFSHCI specific Registers */
+enum dwc_specific_registers {
+ DWC_UFS_REG_HCLKDIV = 0xFC,
+};
+
+/* Link Status*/
+enum link_status {
+ UFSHCD_LINK_IS_DOWN = 1,
+ UFSHCD_LINK_IS_UP = 2,
+};
+
+/* Clock Divider Values: Hex equivalent of frequency in MHz */
+enum clk_div_values {
+ UFSHCD_CLK_DIV_62_5 = 0x3e,
+ UFSHCD_CLK_DIV_125 = 0x7d,
+ UFSHCD_CLK_DIV_200 = 0xc8,
+};
+
+/* Selector Index */
+enum selector_index {
+ SELIND_LN0_TX = 0x00,
+ SELIND_LN1_TX = 0x01,
+ SELIND_LN0_RX = 0x04,
+ SELIND_LN1_RX = 0x05,
+};
+
+#endif /* End of Header */
diff --git a/drivers/scsi/ufs/unipro.h b/drivers/scsi/ufs/unipro.h
index 816a8a4..da16254 100644
--- a/drivers/scsi/ufs/unipro.h
+++ b/drivers/scsi/ufs/unipro.h
@@ -35,6 +35,10 @@
#define TX_LCC_SEQUENCER 0x0032
#define TX_MIN_ACTIVATETIME 0x0033
#define TX_PWM_G6_G7_SYNC_LENGTH 0x0034
+#define TX_REFCLKFREQ 0x00EB
+#define TX_CFGCLKFREQVAL 0x00EC
+#define CFGEXTRATTR 0x00F0
+#define DITHERCTRL2 0x00F1
/*
* M-RX Configuration Attributes
@@ -48,8 +52,38 @@
#define RX_ENTER_HIBERN8 0x00A7
#define RX_BYPASS_8B10B_ENABLE 0x00A8
#define RX_TERMINATION_FORCE_ENABLE 0x0089
+#define RX_REFCLKFREQ 0x00EB
+#define RX_CFGCLKFREQVAL 0x00EC
+#define CFGWIDEINLN 0x00F0
+#define CFGRXCDR8 0x00BA
+#define ENARXDIRECTCFG4 0x00F2
+#define CFGRXOVR8 0x00BD
+#define RXDIRECTCTRL2 0x00C7
+#define ENARXDIRECTCFG3 0x00F3
+#define RXCALCTRL 0x00B4
+#define ENARXDIRECTCFG2 0x00F4
+#define CFGRXOVR4 0x00E9
+#define RXSQCTRL 0x00B5
+#define CFGRXOVR6 0x00BF
#define is_mphy_tx_attr(attr) (attr < RX_MODE)
+
+/*
+ * Common Block Attributes
+ */
+#define TX_GLOBALHIBERNATE UNIPRO_CB_OFFSET(0x002B)
+#define REFCLKMODE UNIPRO_CB_OFFSET(0x00BF)
+#define DIRECTCTRL19 UNIPRO_CB_OFFSET(0x00CD)
+#define DIRECTCTRL10 UNIPRO_CB_OFFSET(0x00E6)
+#define CDIRECTCTRL6 UNIPRO_CB_OFFSET(0x00EA)
+#define RTOBSERVESELECT UNIPRO_CB_OFFSET(0x00F0)
+#define CBDIVFACTOR UNIPRO_CB_OFFSET(0x00F1)
+#define CBDCOCTRL5 UNIPRO_CB_OFFSET(0x00F3)
+#define CBPRGPLL2 UNIPRO_CB_OFFSET(0x00F8)
+#define CBPRGTUNING UNIPRO_CB_OFFSET(0x00FB)
+
+#define UNIPRO_CB_OFFSET(x) (0x8000 | x)
+
/*
* PHY Adpater attributes
*/
@@ -110,6 +144,11 @@
#define PA_STALLNOCONFIGTIME 0x15A3
#define PA_SAVECONFIGTIME 0x15A4
+/*Other attributes*/
+#define VS_MPHYCFGUPDT 0xD085
+#define VS_DEBUGOMC 0xD09E
+#define VS_POWERSTATE 0xD083
+
/* PA power modes */
enum {
FAST_MODE = 1,
--
1.8.1.5
Powered by blists - more mailing lists