Message-id: <1454593456-3162-20-git-send-email-b.zolnierkie@samsung.com>
Date:	Thu, 04 Feb 2016 14:44:16 +0100
From:	Bartlomiej Zolnierkiewicz <b.zolnierkie@...sung.com>
To:	"David S. Miller" <davem@...emloft.net>
Cc:	linux-ide@...r.kernel.org, linux-kernel@...r.kernel.org,
	Tejun Heo <tj@...nel.org>,
	Alan Cox <gnomes@...rguk.ukuu.org.uk>,
	Sergei Shtylyov <sergei.shtylyov@...entembedded.com>,
	b.zolnierkie@...sung.com
Subject: [RC PATCH 19/19] ide: remove deprecated icside host driver

IDE subsystem has been deprecated since 2009 and the majority
(if not all) of Linux distributions have switched to use
libata for ATA support exclusively.

The replacement driver (pata_icside) has been available since
2007 and it supports all the hardware supported by the old
icside host driver.  Also ARM rpc_defconfig has switched to use
libata PATA exclusively in 2007.

Remove the deprecated icside host driver.

Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@...sung.com>
---
 drivers/ide/Kconfig  |  18 +-
 drivers/ide/Makefile |   1 -
 drivers/ide/icside.c | 691 ---------------------------------------------------
 3 files changed, 1 insertion(+), 709 deletions(-)
 delete mode 100644 drivers/ide/icside.c

diff --git a/drivers/ide/Kconfig b/drivers/ide/Kconfig
index 0ce294b..9100755 100644
--- a/drivers/ide/Kconfig
+++ b/drivers/ide/Kconfig
@@ -514,21 +514,6 @@ config BLK_DEV_IDE_TX4939
 	depends on SOC_TX4939
 	select BLK_DEV_IDEDMA_SFF
 
-config BLK_DEV_IDE_ICSIDE
-	tristate "ICS IDE interface support"
-	depends on ARM && ARCH_ACORN
-	help
-	  On Acorn systems, say Y here if you wish to use the ICS IDE
-	  interface card.  This is not required for ICS partition support.
-	  If you are unsure, say N to this.
-
-config BLK_DEV_IDEDMA_ICS
-	bool "ICS DMA support"
-	depends on BLK_DEV_IDE_ICSIDE
-	help
-	  Say Y here if you want to add DMA (Direct Memory Access) support to
-	  the ICS IDE driver.
-
 config BLK_DEV_IDE_RAPIDE
 	tristate "RapIDE interface support"
 	depends on ARM && ARCH_ACORN
@@ -684,8 +669,7 @@ config BLK_DEV_UMC8672
 endif
 
 config BLK_DEV_IDEDMA
-	def_bool BLK_DEV_IDEDMA_SFF || \
-		 BLK_DEV_IDEDMA_ICS || BLK_DEV_IDE_AU1XXX_MDMA2_DBDMA
+	def_bool BLK_DEV_IDEDMA_SFF || BLK_DEV_IDE_AU1XXX_MDMA2_DBDMA
 	select IDE_XFER_MODE
 
 endif # IDE
diff --git a/drivers/ide/Makefile b/drivers/ide/Makefile
index f78616fe..385efa4 100644
--- a/drivers/ide/Makefile
+++ b/drivers/ide/Makefile
@@ -87,7 +87,6 @@ obj-$(CONFIG_BLK_DEV_IDECS)		+= ide-cs.o
 
 obj-$(CONFIG_BLK_DEV_PLATFORM)		+= ide_platform.o
 
-obj-$(CONFIG_BLK_DEV_IDE_ICSIDE)	+= icside.o
 obj-$(CONFIG_BLK_DEV_IDE_RAPIDE)	+= rapide.o
 obj-$(CONFIG_BLK_DEV_PALMCHIP_BK3710)	+= palm_bk3710.o
 
diff --git a/drivers/ide/icside.c b/drivers/ide/icside.c
deleted file mode 100644
index 9f0a48e..0000000
--- a/drivers/ide/icside.c
+++ /dev/null
@@ -1,691 +0,0 @@
-/*
- * Copyright (c) 1996-2004 Russell King.
- *
- * Please note that this platform does not support 32-bit IDE IO.
- */
-
-#include <linux/string.h>
-#include <linux/module.h>
-#include <linux/ioport.h>
-#include <linux/slab.h>
-#include <linux/blkdev.h>
-#include <linux/errno.h>
-#include <linux/ide.h>
-#include <linux/dma-mapping.h>
-#include <linux/device.h>
-#include <linux/init.h>
-#include <linux/scatterlist.h>
-#include <linux/io.h>
-
-#include <asm/dma.h>
-#include <asm/ecard.h>
-
-#define DRV_NAME "icside"
-
-#define ICS_IDENT_OFFSET		0x2280
-
-#define ICS_ARCIN_V5_INTRSTAT		0x0000
-#define ICS_ARCIN_V5_INTROFFSET		0x0004
-#define ICS_ARCIN_V5_IDEOFFSET		0x2800
-#define ICS_ARCIN_V5_IDEALTOFFSET	0x2b80
-#define ICS_ARCIN_V5_IDESTEPPING	6
-
-#define ICS_ARCIN_V6_IDEOFFSET_1	0x2000
-#define ICS_ARCIN_V6_INTROFFSET_1	0x2200
-#define ICS_ARCIN_V6_INTRSTAT_1		0x2290
-#define ICS_ARCIN_V6_IDEALTOFFSET_1	0x2380
-#define ICS_ARCIN_V6_IDEOFFSET_2	0x3000
-#define ICS_ARCIN_V6_INTROFFSET_2	0x3200
-#define ICS_ARCIN_V6_INTRSTAT_2		0x3290
-#define ICS_ARCIN_V6_IDEALTOFFSET_2	0x3380
-#define ICS_ARCIN_V6_IDESTEPPING	6
-
-struct cardinfo {
-	unsigned int dataoffset;
-	unsigned int ctrloffset;
-	unsigned int stepping;
-};
-
-static struct cardinfo icside_cardinfo_v5 = {
-	.dataoffset	= ICS_ARCIN_V5_IDEOFFSET,
-	.ctrloffset	= ICS_ARCIN_V5_IDEALTOFFSET,
-	.stepping	= ICS_ARCIN_V5_IDESTEPPING,
-};
-
-static struct cardinfo icside_cardinfo_v6_1 = {
-	.dataoffset	= ICS_ARCIN_V6_IDEOFFSET_1,
-	.ctrloffset	= ICS_ARCIN_V6_IDEALTOFFSET_1,
-	.stepping	= ICS_ARCIN_V6_IDESTEPPING,
-};
-
-static struct cardinfo icside_cardinfo_v6_2 = {
-	.dataoffset	= ICS_ARCIN_V6_IDEOFFSET_2,
-	.ctrloffset	= ICS_ARCIN_V6_IDEALTOFFSET_2,
-	.stepping	= ICS_ARCIN_V6_IDESTEPPING,
-};
-
-struct icside_state {
-	unsigned int channel;
-	unsigned int enabled;
-	void __iomem *irq_port;
-	void __iomem *ioc_base;
-	unsigned int sel;
-	unsigned int type;
-	struct ide_host *host;
-};
-
-#define ICS_TYPE_A3IN	0
-#define ICS_TYPE_A3USER	1
-#define ICS_TYPE_V6	3
-#define ICS_TYPE_V5	15
-#define ICS_TYPE_NOTYPE	((unsigned int)-1)
-
-/* ---------------- Version 5 PCB Support Functions --------------------- */
-/* Prototype: icside_irqenable_arcin_v5 (struct expansion_card *ec, int irqnr)
- * Purpose  : enable interrupts from card
- */
-static void icside_irqenable_arcin_v5 (struct expansion_card *ec, int irqnr)
-{
-	struct icside_state *state = ec->irq_data;
-
-	writeb(0, state->irq_port + ICS_ARCIN_V5_INTROFFSET);
-}
-
-/* Prototype: icside_irqdisable_arcin_v5 (struct expansion_card *ec, int irqnr)
- * Purpose  : disable interrupts from card
- */
-static void icside_irqdisable_arcin_v5 (struct expansion_card *ec, int irqnr)
-{
-	struct icside_state *state = ec->irq_data;
-
-	readb(state->irq_port + ICS_ARCIN_V5_INTROFFSET);
-}
-
-static const expansioncard_ops_t icside_ops_arcin_v5 = {
-	.irqenable	= icside_irqenable_arcin_v5,
-	.irqdisable	= icside_irqdisable_arcin_v5,
-};
-
-
-/* ---------------- Version 6 PCB Support Functions --------------------- */
-/* Prototype: icside_irqenable_arcin_v6 (struct expansion_card *ec, int irqnr)
- * Purpose  : enable interrupts from card
- */
-static void icside_irqenable_arcin_v6 (struct expansion_card *ec, int irqnr)
-{
-	struct icside_state *state = ec->irq_data;
-	void __iomem *base = state->irq_port;
-
-	state->enabled = 1;
-
-	switch (state->channel) {
-	case 0:
-		writeb(0, base + ICS_ARCIN_V6_INTROFFSET_1);
-		readb(base + ICS_ARCIN_V6_INTROFFSET_2);
-		break;
-	case 1:
-		writeb(0, base + ICS_ARCIN_V6_INTROFFSET_2);
-		readb(base + ICS_ARCIN_V6_INTROFFSET_1);
-		break;
-	}
-}
-
-/* Prototype: icside_irqdisable_arcin_v6 (struct expansion_card *ec, int irqnr)
- * Purpose  : disable interrupts from card
- */
-static void icside_irqdisable_arcin_v6 (struct expansion_card *ec, int irqnr)
-{
-	struct icside_state *state = ec->irq_data;
-
-	state->enabled = 0;
-
-	readb(state->irq_port + ICS_ARCIN_V6_INTROFFSET_1);
-	readb(state->irq_port + ICS_ARCIN_V6_INTROFFSET_2);
-}
-
-/* Prototype: icside_irqprobe(struct expansion_card *ec)
- * Purpose  : detect an active interrupt from card
- */
-static int icside_irqpending_arcin_v6(struct expansion_card *ec)
-{
-	struct icside_state *state = ec->irq_data;
-
-	return readb(state->irq_port + ICS_ARCIN_V6_INTRSTAT_1) & 1 ||
-	       readb(state->irq_port + ICS_ARCIN_V6_INTRSTAT_2) & 1;
-}
-
-static const expansioncard_ops_t icside_ops_arcin_v6 = {
-	.irqenable	= icside_irqenable_arcin_v6,
-	.irqdisable	= icside_irqdisable_arcin_v6,
-	.irqpending	= icside_irqpending_arcin_v6,
-};
-
-/*
- * Handle routing of interrupts.  This is called before
- * we write the command to the drive.
- */
-static void icside_maskproc(ide_drive_t *drive, int mask)
-{
-	ide_hwif_t *hwif = drive->hwif;
-	struct expansion_card *ec = ECARD_DEV(hwif->dev);
-	struct icside_state *state = ecard_get_drvdata(ec);
-	unsigned long flags;
-
-	local_irq_save(flags);
-
-	state->channel = hwif->channel;
-
-	if (state->enabled && !mask) {
-		switch (hwif->channel) {
-		case 0:
-			writeb(0, state->irq_port + ICS_ARCIN_V6_INTROFFSET_1);
-			readb(state->irq_port + ICS_ARCIN_V6_INTROFFSET_2);
-			break;
-		case 1:
-			writeb(0, state->irq_port + ICS_ARCIN_V6_INTROFFSET_2);
-			readb(state->irq_port + ICS_ARCIN_V6_INTROFFSET_1);
-			break;
-		}
-	} else {
-		readb(state->irq_port + ICS_ARCIN_V6_INTROFFSET_2);
-		readb(state->irq_port + ICS_ARCIN_V6_INTROFFSET_1);
-	}
-
-	local_irq_restore(flags);
-}
-
-static const struct ide_port_ops icside_v6_no_dma_port_ops = {
-	.maskproc		= icside_maskproc,
-};
-
-#ifdef CONFIG_BLK_DEV_IDEDMA_ICS
-/*
- * SG-DMA support.
- *
- * Similar to the BM-DMA, but we use the RiscPCs IOMD DMA controllers.
- * There is only one DMA controller per card, which means that only
- * one drive can be accessed at one time.  NOTE! We do not enforce that
- * here, but we rely on the main IDE driver spotting that both
- * interfaces use the same IRQ, which should guarantee this.
- */
-
-/*
- * Configure the IOMD to give the appropriate timings for the transfer
- * mode being requested.  We take the advice of the ATA standards, and
- * calculate the cycle time based on the transfer mode, and the EIDE
- * MW DMA specs that the drive provides in the IDENTIFY command.
- *
- * We have the following IOMD DMA modes to choose from:
- *
- *	Type	Active		Recovery	Cycle
- *	A	250 (250)	312 (550)	562 (800)
- *	B	187		250		437
- *	C	125 (125)	125 (375)	250 (500)
- *	D	62		125		187
- *
- * (figures in brackets are actual measured timings)
- *
- * However, we also need to take care of the read/write active and
- * recovery timings:
- *
- *			Read	Write
- *  	Mode	Active	-- Recovery --	Cycle	IOMD type
- *	MW0	215	50	215	480	A
- *	MW1	80	50	50	150	C
- *	MW2	70	25	25	120	C
- */
-static void icside_set_dma_mode(ide_hwif_t *hwif, ide_drive_t *drive)
-{
-	unsigned long cycle_time = 0;
-	int use_dma_info = 0;
-	const u8 xfer_mode = drive->dma_mode;
-
-	switch (xfer_mode) {
-	case XFER_MW_DMA_2:
-		cycle_time = 250;
-		use_dma_info = 1;
-		break;
-
-	case XFER_MW_DMA_1:
-		cycle_time = 250;
-		use_dma_info = 1;
-		break;
-
-	case XFER_MW_DMA_0:
-		cycle_time = 480;
-		break;
-
-	case XFER_SW_DMA_2:
-	case XFER_SW_DMA_1:
-	case XFER_SW_DMA_0:
-		cycle_time = 480;
-		break;
-	}
-
-	/*
-	 * If we're going to be doing MW_DMA_1 or MW_DMA_2, we should
-	 * take care to note the values in the ID...
-	 */
-	if (use_dma_info && drive->id[ATA_ID_EIDE_DMA_TIME] > cycle_time)
-		cycle_time = drive->id[ATA_ID_EIDE_DMA_TIME];
-
-	ide_set_drivedata(drive, (void *)cycle_time);
-
-	printk(KERN_INFO "%s: %s selected (peak %luMB/s)\n",
-	       drive->name, ide_xfer_verbose(xfer_mode),
-	       2000 / (cycle_time ? cycle_time : (unsigned long) -1));
-}
-
-static const struct ide_port_ops icside_v6_port_ops = {
-	.set_dma_mode		= icside_set_dma_mode,
-	.maskproc		= icside_maskproc,
-};
-
-static void icside_dma_host_set(ide_drive_t *drive, int on)
-{
-}
-
-static int icside_dma_end(ide_drive_t *drive)
-{
-	ide_hwif_t *hwif = drive->hwif;
-	struct expansion_card *ec = ECARD_DEV(hwif->dev);
-
-	disable_dma(ec->dma);
-
-	return get_dma_residue(ec->dma) != 0;
-}
-
-static void icside_dma_start(ide_drive_t *drive)
-{
-	ide_hwif_t *hwif = drive->hwif;
-	struct expansion_card *ec = ECARD_DEV(hwif->dev);
-
-	/* We can not enable DMA on both channels simultaneously. */
-	BUG_ON(dma_channel_active(ec->dma));
-	enable_dma(ec->dma);
-}
-
-static int icside_dma_setup(ide_drive_t *drive, struct ide_cmd *cmd)
-{
-	ide_hwif_t *hwif = drive->hwif;
-	struct expansion_card *ec = ECARD_DEV(hwif->dev);
-	struct icside_state *state = ecard_get_drvdata(ec);
-	unsigned int dma_mode;
-
-	if (cmd->tf_flags & IDE_TFLAG_WRITE)
-		dma_mode = DMA_MODE_WRITE;
-	else
-		dma_mode = DMA_MODE_READ;
-
-	/*
-	 * We can not enable DMA on both channels.
-	 */
-	BUG_ON(dma_channel_active(ec->dma));
-
-	/*
-	 * Ensure that we have the right interrupt routed.
-	 */
-	icside_maskproc(drive, 0);
-
-	/*
-	 * Route the DMA signals to the correct interface.
-	 */
-	writeb(state->sel | hwif->channel, state->ioc_base);
-
-	/*
-	 * Select the correct timing for this drive.
-	 */
-	set_dma_speed(ec->dma, (unsigned long)ide_get_drivedata(drive));
-
-	/*
-	 * Tell the DMA engine about the SG table and
-	 * data direction.
-	 */
-	set_dma_sg(ec->dma, hwif->sg_table, cmd->sg_nents);
-	set_dma_mode(ec->dma, dma_mode);
-
-	return 0;
-}
-
-static int icside_dma_test_irq(ide_drive_t *drive)
-{
-	ide_hwif_t *hwif = drive->hwif;
-	struct expansion_card *ec = ECARD_DEV(hwif->dev);
-	struct icside_state *state = ecard_get_drvdata(ec);
-
-	return readb(state->irq_port +
-		     (hwif->channel ?
-			ICS_ARCIN_V6_INTRSTAT_2 :
-			ICS_ARCIN_V6_INTRSTAT_1)) & 1;
-}
-
-static int icside_dma_init(ide_hwif_t *hwif, const struct ide_port_info *d)
-{
-	hwif->dmatable_cpu	= NULL;
-	hwif->dmatable_dma	= 0;
-
-	return 0;
-}
-
-static const struct ide_dma_ops icside_v6_dma_ops = {
-	.dma_host_set		= icside_dma_host_set,
-	.dma_setup		= icside_dma_setup,
-	.dma_start		= icside_dma_start,
-	.dma_end		= icside_dma_end,
-	.dma_test_irq		= icside_dma_test_irq,
-	.dma_lost_irq		= ide_dma_lost_irq,
-};
-#endif
-
-static int icside_dma_off_init(ide_hwif_t *hwif, const struct ide_port_info *d)
-{
-	return -EOPNOTSUPP;
-}
-
-static void icside_setup_ports(struct ide_hw *hw, void __iomem *base,
-			       struct cardinfo *info, struct expansion_card *ec)
-{
-	unsigned long port = (unsigned long)base + info->dataoffset;
-
-	hw->io_ports.data_addr	 = port;
-	hw->io_ports.error_addr	 = port + (1 << info->stepping);
-	hw->io_ports.nsect_addr	 = port + (2 << info->stepping);
-	hw->io_ports.lbal_addr	 = port + (3 << info->stepping);
-	hw->io_ports.lbam_addr	 = port + (4 << info->stepping);
-	hw->io_ports.lbah_addr	 = port + (5 << info->stepping);
-	hw->io_ports.device_addr = port + (6 << info->stepping);
-	hw->io_ports.status_addr = port + (7 << info->stepping);
-	hw->io_ports.ctl_addr	 = (unsigned long)base + info->ctrloffset;
-
-	hw->irq = ec->irq;
-	hw->dev = &ec->dev;
-}
-
-static const struct ide_port_info icside_v5_port_info = {
-	.host_flags		= IDE_HFLAG_NO_DMA,
-	.chipset		= ide_acorn,
-};
-
-static int icside_register_v5(struct icside_state *state,
-			      struct expansion_card *ec)
-{
-	void __iomem *base;
-	struct ide_host *host;
-	struct ide_hw hw, *hws[] = { &hw };
-	int ret;
-
-	base = ecardm_iomap(ec, ECARD_RES_MEMC, 0, 0);
-	if (!base)
-		return -ENOMEM;
-
-	state->irq_port = base;
-
-	ec->irqaddr  = base + ICS_ARCIN_V5_INTRSTAT;
-	ec->irqmask  = 1;
-
-	ecard_setirq(ec, &icside_ops_arcin_v5, state);
-
-	/*
-	 * Be on the safe side - disable interrupts
-	 */
-	icside_irqdisable_arcin_v5(ec, 0);
-
-	icside_setup_ports(&hw, base, &icside_cardinfo_v5, ec);
-
-	host = ide_host_alloc(&icside_v5_port_info, hws, 1);
-	if (host == NULL)
-		return -ENODEV;
-
-	state->host = host;
-
-	ecard_set_drvdata(ec, state);
-
-	ret = ide_host_register(host, &icside_v5_port_info, hws);
-	if (ret)
-		goto err_free;
-
-	return 0;
-err_free:
-	ide_host_free(host);
-	ecard_set_drvdata(ec, NULL);
-	return ret;
-}
-
-static const struct ide_port_info icside_v6_port_info __initconst = {
-	.init_dma		= icside_dma_off_init,
-	.port_ops		= &icside_v6_no_dma_port_ops,
-	.host_flags		= IDE_HFLAG_SERIALIZE | IDE_HFLAG_MMIO,
-	.mwdma_mask		= ATA_MWDMA2,
-	.swdma_mask		= ATA_SWDMA2,
-	.chipset		= ide_acorn,
-};
-
-static int icside_register_v6(struct icside_state *state,
-			      struct expansion_card *ec)
-{
-	void __iomem *ioc_base, *easi_base;
-	struct ide_host *host;
-	unsigned int sel = 0;
-	int ret;
-	struct ide_hw hw[2], *hws[] = { &hw[0], &hw[1] };
-	struct ide_port_info d = icside_v6_port_info;
-
-	ioc_base = ecardm_iomap(ec, ECARD_RES_IOCFAST, 0, 0);
-	if (!ioc_base) {
-		ret = -ENOMEM;
-		goto out;
-	}
-
-	easi_base = ioc_base;
-
-	if (ecard_resource_flags(ec, ECARD_RES_EASI)) {
-		easi_base = ecardm_iomap(ec, ECARD_RES_EASI, 0, 0);
-		if (!easi_base) {
-			ret = -ENOMEM;
-			goto out;
-		}
-
-		/*
-		 * Enable access to the EASI region.
-		 */
-		sel = 1 << 5;
-	}
-
-	writeb(sel, ioc_base);
-
-	ecard_setirq(ec, &icside_ops_arcin_v6, state);
-
-	state->irq_port   = easi_base;
-	state->ioc_base   = ioc_base;
-	state->sel	  = sel;
-
-	/*
-	 * Be on the safe side - disable interrupts
-	 */
-	icside_irqdisable_arcin_v6(ec, 0);
-
-	icside_setup_ports(&hw[0], easi_base, &icside_cardinfo_v6_1, ec);
-	icside_setup_ports(&hw[1], easi_base, &icside_cardinfo_v6_2, ec);
-
-	host = ide_host_alloc(&d, hws, 2);
-	if (host == NULL)
-		return -ENODEV;
-
-	state->host = host;
-
-	ecard_set_drvdata(ec, state);
-
-#ifdef CONFIG_BLK_DEV_IDEDMA_ICS
-	if (ec->dma != NO_DMA && !request_dma(ec->dma, DRV_NAME)) {
-		d.init_dma = icside_dma_init;
-		d.port_ops = &icside_v6_port_ops;
-		d.dma_ops  = &icside_v6_dma_ops;
-	}
-#endif
-
-	ret = ide_host_register(host, &d, hws);
-	if (ret)
-		goto err_free;
-
-	return 0;
-err_free:
-	ide_host_free(host);
-	if (d.dma_ops)
-		free_dma(ec->dma);
-	ecard_set_drvdata(ec, NULL);
-out:
-	return ret;
-}
-
-static int icside_probe(struct expansion_card *ec, const struct ecard_id *id)
-{
-	struct icside_state *state;
-	void __iomem *idmem;
-	int ret;
-
-	ret = ecard_request_resources(ec);
-	if (ret)
-		goto out;
-
-	state = kzalloc(sizeof(struct icside_state), GFP_KERNEL);
-	if (!state) {
-		ret = -ENOMEM;
-		goto release;
-	}
-
-	state->type	= ICS_TYPE_NOTYPE;
-
-	idmem = ecardm_iomap(ec, ECARD_RES_IOCFAST, 0, 0);
-	if (idmem) {
-		unsigned int type;
-
-		type = readb(idmem + ICS_IDENT_OFFSET) & 1;
-		type |= (readb(idmem + ICS_IDENT_OFFSET + 4) & 1) << 1;
-		type |= (readb(idmem + ICS_IDENT_OFFSET + 8) & 1) << 2;
-		type |= (readb(idmem + ICS_IDENT_OFFSET + 12) & 1) << 3;
-		ecardm_iounmap(ec, idmem);
-
-		state->type = type;
-	}
-
-	switch (state->type) {
-	case ICS_TYPE_A3IN:
-		dev_warn(&ec->dev, "A3IN unsupported\n");
-		ret = -ENODEV;
-		break;
-
-	case ICS_TYPE_A3USER:
-		dev_warn(&ec->dev, "A3USER unsupported\n");
-		ret = -ENODEV;
-		break;
-
-	case ICS_TYPE_V5:
-		ret = icside_register_v5(state, ec);
-		break;
-
-	case ICS_TYPE_V6:
-		ret = icside_register_v6(state, ec);
-		break;
-
-	default:
-		dev_warn(&ec->dev, "unknown interface type\n");
-		ret = -ENODEV;
-		break;
-	}
-
-	if (ret == 0)
-		goto out;
-
-	kfree(state);
- release:
-	ecard_release_resources(ec);
- out:
-	return ret;
-}
-
-static void icside_remove(struct expansion_card *ec)
-{
-	struct icside_state *state = ecard_get_drvdata(ec);
-
-	switch (state->type) {
-	case ICS_TYPE_V5:
-		/* FIXME: tell IDE to stop using the interface */
-
-		/* Disable interrupts */
-		icside_irqdisable_arcin_v5(ec, 0);
-		break;
-
-	case ICS_TYPE_V6:
-		/* FIXME: tell IDE to stop using the interface */
-		if (ec->dma != NO_DMA)
-			free_dma(ec->dma);
-
-		/* Disable interrupts */
-		icside_irqdisable_arcin_v6(ec, 0);
-
-		/* Reset the ROM pointer/EASI selection */
-		writeb(0, state->ioc_base);
-		break;
-	}
-
-	ecard_set_drvdata(ec, NULL);
-
-	kfree(state);
-	ecard_release_resources(ec);
-}
-
-static void icside_shutdown(struct expansion_card *ec)
-{
-	struct icside_state *state = ecard_get_drvdata(ec);
-	unsigned long flags;
-
-	/*
-	 * Disable interrupts from this card.  We need to do
-	 * this before disabling EASI since we may be accessing
-	 * this register via that region.
-	 */
-	local_irq_save(flags);
-	ec->ops->irqdisable(ec, 0);
-	local_irq_restore(flags);
-
-	/*
-	 * Reset the ROM pointer so that we can read the ROM
-	 * after a soft reboot.  This also disables access to
-	 * the IDE taskfile via the EASI region.
-	 */
-	if (state->ioc_base)
-		writeb(0, state->ioc_base);
-}
-
-static const struct ecard_id icside_ids[] = {
-	{ MANU_ICS,  PROD_ICS_IDE  },
-	{ MANU_ICS2, PROD_ICS2_IDE },
-	{ 0xffff, 0xffff }
-};
-
-static struct ecard_driver icside_driver = {
-	.probe		= icside_probe,
-	.remove		= icside_remove,
-	.shutdown	= icside_shutdown,
-	.id_table	= icside_ids,
-	.drv = {
-		.name	= "icside",
-	},
-};
-
-static int __init icside_init(void)
-{
-	return ecard_register_driver(&icside_driver);
-}
-
-static void __exit icside_exit(void)
-{
-	ecard_remove_driver(&icside_driver);
-}
-
-MODULE_AUTHOR("Russell King <rmk@....linux.org.uk>");
-MODULE_LICENSE("GPL");
-MODULE_DESCRIPTION("ICS IDE driver");
-
-module_init(icside_init);
-module_exit(icside_exit);
-- 
1.9.1

Powered by blists - more mailing lists