Message-ID: <56C4DB37.9090802@ti.com>
Date:	Wed, 17 Feb 2016 14:42:31 -0600
From:	"Franklin S Cooper Jr." <fcooper@...com>
To:	Paul Walmsley <paul@...an.com>, "R, Vignesh" <vigneshr@...com>
CC:	Tero Kristo <t-kristo@...com>,
	Thierry Reding <thierry.reding@...il.com>,
	Rob Herring <robh+dt@...nel.org>,
	Pawel Moll <pawel.moll@....com>,
	Mark Rutland <mark.rutland@....com>,
	Ian Campbell <ijc+devicetree@...lion.org.uk>,
	Kumar Gala <galak@...eaurora.org>,
	Benoit Cousson <bcousson@...libre.com>,
	Tony Lindgren <tony@...mide.com>,
	Russell King <linux@....linux.org.uk>,
	Mike Turquette <mturquette@...aro.org>,
	Stephen Boyd <sboyd@...eaurora.org>,
	<linux-pwm@...r.kernel.org>, <devicetree@...r.kernel.org>,
	<linux-kernel@...r.kernel.org>, <linux-omap@...r.kernel.org>,
	<linux-arm-kernel@...ts.infradead.org>, <linux-clk@...r.kernel.org>
Subject: Re: [PATCH v2 2/5] ARM: OMAP2+: DRA7: Add hwmod entries for PWMSS



On 08/31/2015 10:51 AM, Paul Walmsley wrote:
> Hi
>
> On Thu, 16 Jul 2015, R, Vignesh wrote:
>
>> On 07/16/2015 03:24 AM, Paul Walmsley wrote:
>>> On Wed, 3 Jun 2015, Vignesh R wrote:
>>>
>>>> Add hwmod entries for the PWMSS on DRA7.
>>>>
>>>> Set l4_root_clk_div as the main_clk of PWMSS. It is fixed-factored clock
>>>> equal to L4PER2_L3_GICLK/2(l3_iclk_div/2).
>>>> As per AM57x TRM SPRUHZ6[1], October 2014, Section 29.1.3 Table 29-4,
>>>> clock source to PWMSS is L4PER2_L3_GICLK. But it is actually
>>>> L4PER2_L3_GICLK/2. The TRM does not show the division by 2.
>>> Is the divide-by-two coming from PWMSS_EPWM.EPWM_TBCTL[HSPCLKDIV]?  Or is 
>>> HSPCLKDIV a separate divider after the divide-by-2 you mention above?
>> No, it not related to HSPCLKDIV. The TRM wrongly states L4PER2_L3_GICLK
>> as clock input for PWMSS. But actually  L4PER2_L4_GICLK(=L3_GICLK/2) is
>> the clock input for PWMSS. This will be updated in TRM soon.
> OK
>
>>>> --- a/arch/arm/mach-omap2/omap_hwmod_7xx_data.c
>>>> +++ b/arch/arm/mach-omap2/omap_hwmod_7xx_data.c
>>>> @@ -362,6 +362,149 @@ static struct omap_hwmod dra7xx_dcan2_hwmod = {
>>>>  	},
>>>>  };
>>>>  
>>>> +/* pwmss  */
>>>> +static struct omap_hwmod_class_sysconfig dra7xx_epwmss_sysc = {
>>>> +	.rev_offs	= 0x0,
>>>> +	.sysc_offs	= 0x4,
>>>> +	.sysc_flags	= SYSC_HAS_SIDLEMODE | SYSC_HAS_RESET_STATUS,
>>> This doesn't match SPRUHZ6 Table 29-13 "PWMSS_SYSCONFIG".  There's no 
>>> RESETSTATUS bit.  There is a SOFTRESET bit. 
>>>
>>> Could you please confirm whether this is intentional?
>> sorry my bad... I will change this in v3.
> OK
>
>>>> +/* ecap0 */
>>>> +struct omap_hwmod dra7xx_ecap0_hwmod = {
>>>> +	.name		= "ecap0",
>>>> +	.class		= &dra7xx_ecap_hwmod_class,
>>>> +	.clkdm_name	= "l4per2_clkdm",
>>>> +	.main_clk	= "l4_root_clk_div",
>>> Looking at SPRUHZ6 Section 29.1.4.2 "PWMSS Modules Local Clock Gating", 
>>> there appears to be a local "mini-PRCM" for the PWMSS which implements 
>>> clock gating and reports back on the status of what I'd guess is the local 
>>> clock gating FSM.
>>>
>>> So from that point of view, you should probably create a clock driver that 
>>> manages both the clock gate request bit and the FSM status bit.  It should 
>>> be something that can be reused for the other PWMSS IP blocks.  Then 
>>> you'd create per-IP block clock nodes and set the main_clk to point to 
>>> that node.
>> Since, this register is within the config space of PWMSS, the individual
>> gating and reporting for the modules within PWMSS
>> (PWMSS_CLKCONFIG) is currently being taken care by pwm-tipwmss.c(almost
>> the sole function this driver is doing). It has been the same since
>> am335x. Adding new clock nodes will result in driver changes and also
>> changes to am335x, am437x (and other platforms) hwmod files. It also
>> involves adding new nodes to clocks.dtsi and it will be difficult to
>> maintain backward compatibility for older platforms. Is it not better to
>> keep this as is, in order to maintain consistency (with am335x, am437x
>> etc) and also that these clock bits are within IP's config space?
> It's certainly possible that we as maintainers didn't look closely enough 
> at the AM33xx data for the PWMSS when we merged it.  But if that's 
> incorrect too, then now is the time to fix this.  Otherwise it will never 
> get fixed, since each new group of people patching this code will keep 
> punting it off to the indeterminate future.
>
> In terms of hwmod data: based on the register maps in sections 29.4.3, 
> 29.3.3, and 29.2.3 of SPRUHZ6, none of these subdevices are hwmod devices.  
> They don't support the Highlander OCP registers, they have no individual 
> PRCM registers or register bitfields, and all of the idle and status 
> reporting is to the PWMSS top-level IP block itself.  So it looks to me 
> like the eCAP, eQEP, and ePWM modules should be registered via DT, rather 
> than via hwmod.  It looks like you can get away with using the 
> "simple-bus" abstraction, but you might ultimately have to define 
> something custom here.  However, the PWMSS top level subsystem, described 
> in section 29.1, does have the OCP registers, sideband signals, etc., and 
> thus should remain a hwmod-registered device (via DT).
>
> In terms of the clock data: based on section 29.1.4, section 29.1.5.2, 
> figure 29-3, and table 29-4, there are several clock gating control bits.  
> These should be modeled as clock nodes in the Linux common clock 
> framework.  Furthermore these registers are located inside the PWMSS 
> subsystem itself, and are only accessible when the PWMSS IP block is 
> functional in a PM runtime point of view: i.e., when the block is mapped 
> into memory space, clocked and out of reset, etc.  So the clock types for 
> the PWMSS_CFG IP block should most likely be implemented in the PWMSS 
> driver.  I think you'll still be able to define the clock node data itself 
> in DT, but this will probably need a closer look.  Ideally, since the 
> clock node register address data is the same for all three subsystem 
> instances, one would be able to simply include a DT include file three 
> times; but the DT binding data format may ultimately make this 
> impractical.
>
> In terms of the transition from the old approach to this approach, it ooks 
> to me like the first thing to do would be to convert
> drivers/pwm/pwm-tipwmss.c to define some clk_ops and register some clock
> nodes with the CCF.  You've got the meat of the clock gating control code
> there already.  Then the next thing to do would be to to get rid of
> pwmss_submodule_state_change() and use
> clk_{prepare,enable,disable,unprepare}*() in the drivers/pwm/pwm-ti*.c
> subdrivers instead.  All of that looks like it should be possible to  
> implement in a backwards-compatible way.  Then you'd convert the eCAP, 
> eQEP, and ePWM code to probe as platform_devices, driven from a simple-bus 
> or pwmss-bus or whatever in the DT data.  Naturally, the AM33xx/43xx data 
> should be fixed also.  

Hi Paul,

Sorry for bringing up this old thread again.

I am working on updating this patchset on behalf of Vignesh
based on your suggestion. During the process of converting
the pwm-tipwmss.c to be a clock provider I discovered that
there is an issue with the PWMSS local clock gates. For
example on AM437x if you run the below commands you will get
a " Custom Error: MASTER M2 (64-bit) TARGET L4_PER_0 (Read):
Data Access in User mode during Functional access" error.

rmmod pwm_tiecap
rmmod pwm_bl
rmmod pwm_tiecap
modprobe pwm_tiecap
modprobe pwm_bl

Full Log: http://pastebin.com/sEyy52HV

On device powerup, the various PWMSS local clock gates are
"unlocked". The remove call in the ecap driver gates the
local PWMSS clock gate for the ecap. The probe of the ecap
driver "unlocks" the clock gate for the ecap. However, once
you try to access any of the ecap registers which is
indirectly accessed by the pwm_bl driver you will get an
error. This is because the ecap clock is still being gated.

This has been verified by hardware folks on our side. Its
been determined these registers are not needed since they
were designed for devices that didn't have a PRCM.
Therefore, the current plan is to update the trms of
AM335x,AM437x,DRA7 and AM57x to make it clear that these
registers shouldn't be touched.

I plan on sending a patch for the pwm-tipwmss.c driver
essentially removing anything that touches the
PWMSS_CLKCONFIG and PWMSS_CLKSTATUS registers. I will also
be sending a v3 version of this patch since I believe the
struct omap_hwmod dra7xx_ecap0_hwmod and similar entries you
had comments about before are ok to leave as is based on the
above findings.
>
>
> - Paul
> --
> To unsubscribe from this list: send the line "unsubscribe linux-omap" in
> the body of a message to majordomo@...r.kernel.org
> More majordomo info at  http://vger.kernel.org/majordomo-info.html

Powered by blists - more mailing lists