| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-ID: <20160229201714.GA18909@shlinux2.ap.freescale.net>
Date: Tue, 1 Mar 2016 04:17:14 +0800
From: Han Xu <xhnjupt@...il.com>
To: Yunhui Cui <yunhui.cui@....com>
Cc: Yunhui Cui <B56489@...escale.com>,
"dwmw2@...radead.org" <dwmw2@...radead.org>,
"computersforpeace@...il.com" <computersforpeace@...il.com>,
"han.xu@...escale.com" <han.xu@...escale.com>,
"linux-mtd@...ts.infradead.org" <linux-mtd@...ts.infradead.org>,
"linux-kernel@...r.kernel.org" <linux-kernel@...r.kernel.org>,
"linux-arm-kernel@...ts.infradead.org"
<linux-arm-kernel@...ts.infradead.org>, Yao Yuan <yao.yuan@....com>
Subject: Re: [PATCH v2 3/4] mtd:spi-nor:fsl-quadspi:Add fast-read mode support
On Mon, Feb 29, 2016 at 03:43:36AM +0000, Yunhui Cui wrote:
> Hi Han,
>
> But I don't think QuadSPI driver need to check the m25p,fast-read property again since spi-nor layer has already done that. Adding the property in flash node should work in the same way.
>
> [Yunhui]: There are three modes in fsl-quadspi driver , fast mode, quad mode, ddr quad read. The last parameter mode of spi_nor_scan() I have to specify . Otherwise, flash is still set to quad mode.
If the Nor chip behaves as you said only support fasst-read, the (info->flags &
SPI_NOR_QUAD_READ) can only take false path.
> spi-nor.c:
>
> 1419 if (mode == SPI_NOR_QUAD && info->flags & SPI_NOR_QUAD_READ) {
> 1420 ret = set_quad_mode(nor, info);
> 1421 if (ret) {
> 1422 dev_err(dev, "quad mode not supported\n");
> 1423 return ret;
> 1424 }
> 1425 nor->flash_read = SPI_NOR_QUAD;
> 1426 } else if (mode == SPI_NOR_DUAL && info->flags & SPI_NOR_DUAL_READ) {
> 1427 nor->flash_read = SPI_NOR_DUAL;
> 1428 }
>
>
> Thanks
> Yunhui
> -----Original Message-----
> From: Han Xu [mailto:xhnjupt@...il.com]
> Sent: Saturday, February 27, 2016 12:32 AM
> To: Yunhui Cui
> Cc: Yunhui Cui; dwmw2@...radead.org; computersforpeace@...il.com; han.xu@...escale.com; linux-mtd@...ts.infradead.org; linux-kernel@...r.kernel.org; linux-arm-kernel@...ts.infradead.org; Yao Yuan
> Subject: Re: [PATCH v2 3/4] mtd:spi-nor:fsl-quadspi:Add fast-read mode support
>
> On Thu, Feb 25, 2016 at 08:07:22AM +0000, Yunhui Cui wrote:
> > Hi Han,
> >
> > I have provided the options " m25p,fast-read ", because there are probable some flashes can't support quad mode.
> > So we should support fast-read mode in our driver. Moreover, There is a option to select fast-read mode in spi_nor.c :
> > /* If we were instantiated by DT, use it */
> > if (of_property_read_bool(np, "m25p,fast-read"))
> > nor->flash_read = SPI_NOR_FAST;
>
> Did you have some REAL cases using SPI NOR that only supports upto fast-read with Quad SPI driver? Neither fast-read or normal-read, which is actually more general, supported in the driver, just because I didn't see any REAL cases till now.
>
> I didn't run against the patch, although IMO it's not that necessary. But I don't think QuadSPI driver need to check the m25p,fast-read property again since spi-nor layer has already done that. Adding the property in flash node should work in the same way.
>
> >
> > Thanks
> > Yunhui
> >
> > -----Original Message-----
> > From: Han Xu [mailto:xhnjupt@...il.com]
> > Sent: Thursday, February 18, 2016 2:08 AM
> > To: Yunhui Cui
> > Cc: dwmw2@...radead.org; computersforpeace@...il.com;
> > han.xu@...escale.com; linux-mtd@...ts.infradead.org;
> > linux-kernel@...r.kernel.org; linux-arm-kernel@...ts.infradead.org;
> > Yao Yuan
> > Subject: Re: [PATCH v2 3/4] mtd:spi-nor:fsl-quadspi:Add fast-read mode
> > support
> >
> > On Mon, Feb 01, 2016 at 07:30:07PM +0800, Yunhui Cui wrote:
> > > The qspi driver add generic fast-read mode for different flash
> > > venders. There are some different board flash work on different
> > > mode, such fast-read, quad-mode.
> > > So we have to modify the third entrace parameter of spi_nor_scan().
> > >
> > > Signed-off-by: Yunhui Cui <B56489@...escale.com>
> > > ---
> > > drivers/mtd/spi-nor/fsl-quadspi.c | 27 +++++++++++++++++++++------
> > > 1 file changed, 21 insertions(+), 6 deletions(-)
> > >
> > > diff --git a/drivers/mtd/spi-nor/fsl-quadspi.c
> > > b/drivers/mtd/spi-nor/fsl-quadspi.c
> > > index 9861290..0a31cb1 100644
> > > --- a/drivers/mtd/spi-nor/fsl-quadspi.c
> > > +++ b/drivers/mtd/spi-nor/fsl-quadspi.c
> > > @@ -389,11 +389,21 @@ static void fsl_qspi_init_lut(struct fsl_qspi *q)
> > > /* Read */
> > > lut_base = SEQID_READ * 4;
> > >
> > > - qspi_writel(q, LUT0(CMD, PAD1, read_op) | LUT1(ADDR, PAD1, addrlen),
> > > - base + QUADSPI_LUT(lut_base));
> > > - qspi_writel(q, LUT0(DUMMY, PAD1, read_dm) |
> > > - LUT1(FSL_READ, PAD4, rxfifo),
> > > - base + QUADSPI_LUT(lut_base + 1));
> > > + if (nor->flash_read == SPI_NOR_FAST) {
> > > + qspi_writel(q, LUT0(CMD, PAD1, read_op) |
> > > + LUT1(ADDR, PAD1, addrlen),
> > > + base + QUADSPI_LUT(lut_base));
> > > + qspi_writel(q, LUT0(DUMMY, PAD1, read_dm) |
> > > + LUT1(FSL_READ, PAD1, rxfifo),
> > > + base + QUADSPI_LUT(lut_base + 1));
> > > + } else if (nor->flash_read == SPI_NOR_QUAD) {
> > > + qspi_writel(q, LUT0(CMD, PAD1, read_op) |
> > > + LUT1(ADDR, PAD1, addrlen),
> > > + base + QUADSPI_LUT(lut_base));
> > > + qspi_writel(q, LUT0(DUMMY, PAD1, read_dm) |
> > > + LUT1(FSL_READ, PAD4, rxfifo),
> > > + base + QUADSPI_LUT(lut_base + 1));
> > > + }
> > >
> > > /* Write enable */
> > > lut_base = SEQID_WREN * 4;
> > > @@ -468,6 +478,7 @@ static int fsl_qspi_get_seqid(struct fsl_qspi
> > > *q,
> > > u8 cmd) {
> > > switch (cmd) {
> > > case SPINOR_OP_READ_1_1_4:
> > > + case SPINOR_OP_READ_FAST:
> > > return SEQID_READ;
> > > case SPINOR_OP_WREN:
> > > return SEQID_WREN;
> > > @@ -963,6 +974,7 @@ static int fsl_qspi_probe(struct platform_device *pdev)
> > > struct spi_nor *nor;
> > > struct mtd_info *mtd;
> > > int ret, i = 0;
> > > + enum read_mode mode = SPI_NOR_QUAD;
> > >
> > > q = devm_kzalloc(dev, sizeof(*q), GFP_KERNEL);
> > > if (!q)
> > > @@ -1064,7 +1076,10 @@ static int fsl_qspi_probe(struct platform_device *pdev)
> > > /* set the chip address for READID */
> > > fsl_qspi_set_base_addr(q, nor);
> > >
> > > - ret = spi_nor_scan(nor, NULL, SPI_NOR_QUAD);
> > > + ret = of_property_read_bool(np, "m25p,fast-read");
> > > + mode = (ret) ? SPI_NOR_FAST : SPI_NOR_QUAD;
> > > +
> > > + ret = spi_nor_scan(nor, NULL, mode);
> > > if (ret)
> > > goto mutex_failed;
> > >
> > I understand you want to provide a more generic read mode, but this is a quad spi driver, I prefer to provide the options, either quad read/quad IO read, or just normal read.
> > > --
> > > 2.1.0.27.g96db324
> > >
> > >
> > > ______________________________________________________
> > > Linux MTD discussion mailing list
> > > http://lists.infradead.org/mailman/listinfo/linux-mtd/
Powered by blists - more mailing lists