[<prev] [next>] [<thread-prev] [thread-next>] [day] [month] [year] [list]
Message-ID: <20160317172551.GA3922@rob-hp-laptop>
Date: Thu, 17 Mar 2016 12:25:51 -0500
From: Rob Herring <robh@...nel.org>
To: Neil Armstrong <narmstrong@...libre.com>
Cc: linux-kernel@...r.kernel.org, linux-arm-kernel@...ts.infradead.org,
linus.walleij@...aro.org, linux-gpio@...r.kernel.org,
devicetree@...r.kernel.org
Subject: Re: [PATCH v2 12/18] dt-bindings: Add PLX Technology OXNAS pinctrl
and gpio bindings
On Wed, Mar 09, 2016 at 11:24:14AM +0100, Neil Armstrong wrote:
> Signed-off-by: Neil Armstrong <narmstrong@...libre.com>
> ---
> .../devicetree/bindings/gpio/gpio_oxnas.txt | 27 ++++++
> .../bindings/pinctrl/plxtech,pinctrl.txt | 100 +++++++++++++++++++++
> 2 files changed, 127 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/gpio/gpio_oxnas.txt
> create mode 100644 Documentation/devicetree/bindings/pinctrl/plxtech,pinctrl.txt
>
> diff --git a/Documentation/devicetree/bindings/gpio/gpio_oxnas.txt b/Documentation/devicetree/bindings/gpio/gpio_oxnas.txt
> new file mode 100644
> index 0000000..cbb03c4
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/gpio/gpio_oxnas.txt
> @@ -0,0 +1,27 @@
> +PLX Technology OXNAS SoC GPIO Controller
> +==========================================
> +
> +Required properties:
> +- compatible: "oxsemi,ox810se-gpio".
> +- reg: Should contain GPIO controller registers location and length
> +- interrupts: Should be the port interrupt shared by all the pins.
> +- #gpio-cells: Should be two. The first cell is the pin number and
> + the second cell is used to specify optional parameters (currently
> + unused).
> +- gpio-controller: Marks the device node as a GPIO controller.
> +
> +optional properties:
> +- #gpio-lines: Number of gpio if absent 32.
> +
> +
> +Example:
> + gpio0: gpio@...000 {
Drop the leading 0s.
> + compatible = "oxsemi,ox810se-gpio";
> + reg = <0x000000 0x100000>;
> + interrupts = <21>;
> + #gpio-cells = <2>;
> + gpio-controller;
> + interrupt-controller;
> + #interrupt-cells = <2>;
> + #gpio-lines = <32>;
> + };
> diff --git a/Documentation/devicetree/bindings/pinctrl/plxtech,pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/plxtech,pinctrl.txt
> new file mode 100644
> index 0000000..0c5051a
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/pinctrl/plxtech,pinctrl.txt
> @@ -0,0 +1,100 @@
> +PLX Technology OXNAS SoC Pinmux Controller
> +==========================================
> +
> +The OXNAS Pinmux Controller, enables the IC to share one PAD to several
> +functional blocks. The sharing is done by multiplexing the PAD input/output
> +signals. For each PAD there are up to 8 muxing options (called periph modes).
> +Since different modules require different PAD settings
> +(like pull up, keeper, etc) the contoller controls also the PAD settings
> +parameters.
> +
> +Please refer to pinctrl-bindings.txt in this directory for details of the
> +common pinctrl bindings used by client devices, including the meaning of the
> +phrase "pin configuration node".
> +
> +OXNAS pin configuration node is a node of a group of pins which can be
> +used for a specific device or function. This node represents both mux and config
> +of the pins in that group. The 'pins' selects the function mode(also named pin
> +mode) this pin can work on and the 'config' configures various pad settings
> +such as pull-up, multi drive, etc.
> +
> +Required properties for iomux controller:
> +- compatible: "oxsemi,ox810se-pinctrl"
> +- plxtech,mux-mask: array of mask (periph per bank) to describe if a pin can be
> + configured in this periph mode. All the periph and bank need to be describe.
> +- plxtech,sys-ctrl: a phandle to the system controller syscon node
> +
> +How to create such array:
> +
> +Each column will represent the possible peripheral of the pinctrl
> +Each line will represent a pio bank
> +
> +For example :
> +Peripheral: 2 ( A and B)
> +Bank: 2 (A, B and C)
> +=>
> +
> + /* A B */
> + 0xffffffff 0xffc00c3b /* pioA */
> + 0xffffffff 0x7fff3ccf /* pioB */
> +
> +For each peripheral/bank we will descibe in a u32 if a pin can be
> +configured in it by putting 1 to the pin bit (1 << pin)
> +
> +Required properties for pin configuration node:
> +- plxtech,pins: 4 integers array, represents a group of pins mux and config
> + setting. The format is plxtech,pins = <PIN_BANK PIN_BANK_NUM PERIPH CONFIG>.
> + The PERIPH 0 means gpio, PERIPH 1 is periph A, PERIPH 2 is periph B...
> + PIN_BANK 0 is pioA, PIN_BANK 1 is pioB...
> +
> +Bits used for CONFIG:
> + - None Yet
> +
> +Examples:
> +
> +pinctrl: pinctrl {
> + compatible = "oxsemi,ox810se-pinctrl", "simple-bus";
> + #address-cells = <1>;
> + #size-cells = <1>;
> + ranges;
> +
> + /* Regmap for sys registers */
> + plxtech,sys-ctrl = <&sys>;
> +
> + /* Default, all-open mux-map */
> + plxtech,mux-mask = <
> + 0xFFFFFFFF 0xFFFFFFFF 0xFFFFFFFF 0xFFFFFFFF 0xFFFFFFFF
> + 0xFFFFFFFF 0xFFFFFFFF 0xFFFFFFFF 0xFFFFFFFF 0xFFFFFFFF
> + >;
> +
> + uart0 {
> + pinctrl_uart0: uart0 {
> + plxtech,pins = <0 31 3 0
> + 0 32 3 0>;
> + };
> + pinctrl_uart0_modem: uart0_modem {
> + plxtech,pins = <0 27 3 0
> + 0 28 3 0
> + 0 29 3 0
> + 0 30 3 0
> + 0 33 3 0
> + 0 34 3 0>;
> + };
> + };
> +};
> +
> +uart0: uart@...000 {
serial@...000
With those changes:
Acked-by: Rob Herring <robh@...nel.org>
Powered by blists - more mailing lists