| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-Id: <E1algTa-0004H8-4T@finisterre>
Date: Thu, 31 Mar 2016 10:33:46 -0700
From: Mark Brown <broonie@...nel.org>
To: Georgi Djakov <georgi.djakov@...aro.org>,
Stephen Boyd <stephen.boyd@...aro.org>,
Mark Brown <broonie@...nel.org>
Cc: linux-kernel@...r.kernel.org
Subject: Applied "regulator: qcom_spmi: Add slewing delays for all SMPS types" to the regulator tree
The patch
regulator: qcom_spmi: Add slewing delays for all SMPS types
has been applied to the regulator tree at
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator.git
All being well this means that it will be integrated into the linux-next
tree (usually sometime in the next 24 hours) and sent to Linus during
the next merge window (or sooner if it is a bug fix), however if
problems are discovered then the patch may be dropped or reverted.
You may get further e-mails resulting from automated or manual testing
and review of the tree, please engage with people reporting problems and
send followup patches addressing any issues that are reported if needed.
If any updates are required or you are submitting further changes they
should be sent as incremental updates against current git, existing
patches will not be replaced.
Please add any relevant lists and maintainers to the CCs when replying
to this mail.
Thanks,
Mark
>From 2cf7b99cf74b435f27e48aa2829300c4d0aa65a0 Mon Sep 17 00:00:00 2001
From: Stephen Boyd <stephen.boyd@...aro.org>
Date: Wed, 30 Mar 2016 18:57:49 -0700
Subject: [PATCH] regulator: qcom_spmi: Add slewing delays for all SMPS types
Only the FT SMPS type regulators have slewing supported in the
driver, but all types of SMPS regulators need the same support.
The only difference is that some SMPS regulators don't have a
step size and the step delay is typically 20, not 8. Luckily, the
step size reads as 0 for the non-FT types, so we can always read
that, but we need to detect which type of regulator we're using
to figure out what step delay to use. Make these minor
adjustments to the slew rate calculations and add support for the
delay function to the appropriate regulator ops.
Reported-by: Georgi Djakov <georgi.djakov@...aro.org>
Signed-off-by: Stephen Boyd <stephen.boyd@...aro.org>
Signed-off-by: Mark Brown <broonie@...nel.org>
---
drivers/regulator/qcom_spmi-regulator.c | 29 ++++++++++++++++++++++++-----
1 file changed, 24 insertions(+), 5 deletions(-)
diff --git a/drivers/regulator/qcom_spmi-regulator.c b/drivers/regulator/qcom_spmi-regulator.c
index 3550f7f7c2eb..fdea94c5a016 100644
--- a/drivers/regulator/qcom_spmi-regulator.c
+++ b/drivers/regulator/qcom_spmi-regulator.c
@@ -246,6 +246,7 @@ enum spmi_common_control_register_index {
/* Minimum voltage stepper delay for each step. */
#define SPMI_FTSMPS_STEP_DELAY 8
+#define SPMI_DEFAULT_STEP_DELAY 20
/*
* The ratio SPMI_FTSMPS_STEP_MARGIN_NUM/SPMI_FTSMPS_STEP_MARGIN_DEN is used to
@@ -1008,6 +1009,7 @@ static struct regulator_ops spmi_smps_ops = {
.disable = spmi_regulator_common_disable,
.is_enabled = spmi_regulator_common_is_enabled,
.set_voltage = spmi_regulator_common_set_voltage,
+ .set_voltage_time_sel = spmi_regulator_set_voltage_time_sel,
.get_voltage = spmi_regulator_common_get_voltage,
.list_voltage = spmi_regulator_common_list_voltage,
.set_mode = spmi_regulator_common_set_mode,
@@ -1081,6 +1083,7 @@ static struct regulator_ops spmi_ult_lo_smps_ops = {
.disable = spmi_regulator_common_disable,
.is_enabled = spmi_regulator_common_is_enabled,
.set_voltage = spmi_regulator_ult_lo_smps_set_voltage,
+ .set_voltage_time_sel = spmi_regulator_set_voltage_time_sel,
.get_voltage = spmi_regulator_ult_lo_smps_get_voltage,
.list_voltage = spmi_regulator_common_list_voltage,
.set_mode = spmi_regulator_common_set_mode,
@@ -1094,6 +1097,7 @@ static struct regulator_ops spmi_ult_ho_smps_ops = {
.disable = spmi_regulator_common_disable,
.is_enabled = spmi_regulator_common_is_enabled,
.set_voltage = spmi_regulator_single_range_set_voltage,
+ .set_voltage_time_sel = spmi_regulator_set_voltage_time_sel,
.get_voltage = spmi_regulator_single_range_get_voltage,
.list_voltage = spmi_regulator_common_list_voltage,
.set_mode = spmi_regulator_common_set_mode,
@@ -1245,11 +1249,11 @@ found:
return 0;
}
-static int spmi_regulator_ftsmps_init_slew_rate(struct spmi_regulator *vreg)
+static int spmi_regulator_init_slew_rate(struct spmi_regulator *vreg)
{
int ret;
u8 reg = 0;
- int step, delay, slew_rate;
+ int step, delay, slew_rate, step_delay;
const struct spmi_voltage_range *range;
ret = spmi_vreg_read(vreg, SPMI_COMMON_REG_STEP_CTRL, ®, 1);
@@ -1262,6 +1266,15 @@ static int spmi_regulator_ftsmps_init_slew_rate(struct spmi_regulator *vreg)
if (!range)
return -EINVAL;
+ switch (vreg->logical_type) {
+ case SPMI_REGULATOR_LOGICAL_TYPE_FTSMPS:
+ step_delay = SPMI_FTSMPS_STEP_DELAY;
+ break;
+ default:
+ step_delay = SPMI_DEFAULT_STEP_DELAY;
+ break;
+ }
+
step = reg & SPMI_FTSMPS_STEP_CTRL_STEP_MASK;
step >>= SPMI_FTSMPS_STEP_CTRL_STEP_SHIFT;
@@ -1270,7 +1283,7 @@ static int spmi_regulator_ftsmps_init_slew_rate(struct spmi_regulator *vreg)
/* slew_rate has units of uV/us */
slew_rate = SPMI_FTSMPS_CLOCK_RATE * range->step_uV * (1 << step);
- slew_rate /= 1000 * (SPMI_FTSMPS_STEP_DELAY << delay);
+ slew_rate /= 1000 * (step_delay << delay);
slew_rate *= SPMI_FTSMPS_STEP_MARGIN_NUM;
slew_rate /= SPMI_FTSMPS_STEP_MARGIN_DEN;
@@ -1411,10 +1424,16 @@ static int spmi_regulator_of_parse(struct device_node *node,
return ret;
}
- if (vreg->logical_type == SPMI_REGULATOR_LOGICAL_TYPE_FTSMPS) {
- ret = spmi_regulator_ftsmps_init_slew_rate(vreg);
+ switch (vreg->logical_type) {
+ case SPMI_REGULATOR_LOGICAL_TYPE_FTSMPS:
+ case SPMI_REGULATOR_LOGICAL_TYPE_ULT_LO_SMPS:
+ case SPMI_REGULATOR_LOGICAL_TYPE_ULT_HO_SMPS:
+ case SPMI_REGULATOR_LOGICAL_TYPE_SMPS:
+ ret = spmi_regulator_init_slew_rate(vreg);
if (ret)
return ret;
+ default:
+ break;
}
if (vreg->logical_type != SPMI_REGULATOR_LOGICAL_TYPE_VS)
--
2.8.0.rc3
Powered by blists - more mailing lists