| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-ID: <1462162987-13023-14-git-send-email-kishon@ti.com>
Date: Mon, 2 May 2016 09:53:04 +0530
From: Kishon Vijay Abraham I <kishon@...com>
To: <gregkh@...uxfoundation.org>
CC: <kishon@...com>, <linux-kernel@...r.kernel.org>
Subject: [PATCH 13/16] phy: bcm-ns-usb2: new driver for USB 2.0 PHY on Northstar
From: Rafał Miłecki <zajec5@...il.com>
Northstar is a family of SoCs used in home routers. They have USB 2.0
and 3.0 controllers with PHYs that need to be properly initialized.
This driver provides PHY init support in a generic way and can be bound
with an EHCI controller driver.
There are (just a few) registers being defined in bcma header. It's
because DMU/CRU registers will be also needed in other drivers. We will
need them e.g. in PCIe controller/PHY driver and at some point probably
in clock driver for BCM53573 chipset. By using include/linux/bcma/ we
avoid code duplication.
Signed-off-by: Rafał Miłecki <zajec5@...il.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@...com>
---
.../devicetree/bindings/phy/bcm-ns-usb2-phy.txt | 21 +++
drivers/phy/Kconfig | 9 ++
drivers/phy/Makefile | 1 +
drivers/phy/phy-bcm-ns-usb2.c | 137 ++++++++++++++++++++
include/linux/bcma/bcma.h | 1 +
include/linux/bcma/bcma_driver_arm_c9.h | 15 +++
6 files changed, 184 insertions(+)
create mode 100644 Documentation/devicetree/bindings/phy/bcm-ns-usb2-phy.txt
create mode 100644 drivers/phy/phy-bcm-ns-usb2.c
create mode 100644 include/linux/bcma/bcma_driver_arm_c9.h
diff --git a/Documentation/devicetree/bindings/phy/bcm-ns-usb2-phy.txt b/Documentation/devicetree/bindings/phy/bcm-ns-usb2-phy.txt
new file mode 100644
index 0000000..a7aee9e
--- /dev/null
+++ b/Documentation/devicetree/bindings/phy/bcm-ns-usb2-phy.txt
@@ -0,0 +1,21 @@
+Driver for Broadcom Northstar USB 2.0 PHY
+
+Required properties:
+- compatible: brcm,ns-usb2-phy
+- reg: iomem address range of DMU (Device Management Unit)
+- reg-names: "dmu", the only needed & supported reg right now
+- clocks: USB PHY reference clock
+- clock-names: "phy-ref-clk", the only needed & supported clock right now
+
+To initialize USB 2.0 PHY driver needs to setup PLL correctly. To do this it
+requires passing phandle to the USB PHY reference clock.
+
+Example:
+ usb2-phy {
+ compatible = "brcm,ns-usb2-phy";
+ reg = <0x1800c000 0x1000>;
+ reg-names = "dmu";
+ #phy-cells = <0>;
+ clocks = <&genpll BCM_NSP_GENPLL_USB_PHY_REF_CLK>;
+ clock-names = "phy-ref-clk";
+ };
diff --git a/drivers/phy/Kconfig b/drivers/phy/Kconfig
index f6ff76e..f2b458f 100644
--- a/drivers/phy/Kconfig
+++ b/drivers/phy/Kconfig
@@ -15,6 +15,15 @@ config GENERIC_PHY
phy users can obtain reference to the PHY. All the users of this
framework should select this config.
+config PHY_BCM_NS_USB2
+ tristate "Broadcom Northstar USB 2.0 PHY Driver"
+ depends on ARCH_BCM_IPROC || COMPILE_TEST
+ depends on HAS_IOMEM && OF
+ select GENERIC_PHY
+ help
+ Enable this to support Broadcom USB 2.0 PHY connected to the USB
+ controller on Northstar family.
+
config PHY_BERLIN_USB
tristate "Marvell Berlin USB PHY Driver"
depends on ARCH_BERLIN && RESET_CONTROLLER && HAS_IOMEM && OF
diff --git a/drivers/phy/Makefile b/drivers/phy/Makefile
index f03fa1f..0de09e1 100644
--- a/drivers/phy/Makefile
+++ b/drivers/phy/Makefile
@@ -3,6 +3,7 @@
#
obj-$(CONFIG_GENERIC_PHY) += phy-core.o
+obj-$(CONFIG_PHY_BCM_NS_USB2) += phy-bcm-ns-usb2.o
obj-$(CONFIG_PHY_BERLIN_USB) += phy-berlin-usb.o
obj-$(CONFIG_PHY_BERLIN_SATA) += phy-berlin-sata.o
obj-$(CONFIG_PHY_DM816X_USB) += phy-dm816x-usb.o
diff --git a/drivers/phy/phy-bcm-ns-usb2.c b/drivers/phy/phy-bcm-ns-usb2.c
new file mode 100644
index 0000000..95ab6b2
--- /dev/null
+++ b/drivers/phy/phy-bcm-ns-usb2.c
@@ -0,0 +1,137 @@
+/*
+ * Broadcom Northstar USB 2.0 PHY Driver
+ *
+ * Copyright (C) 2016 Rafał Miłecki <zajec5@...il.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ */
+
+#include <linux/bcma/bcma.h>
+#include <linux/clk.h>
+#include <linux/delay.h>
+#include <linux/err.h>
+#include <linux/module.h>
+#include <linux/of_address.h>
+#include <linux/of_platform.h>
+#include <linux/phy/phy.h>
+#include <linux/platform_device.h>
+#include <linux/slab.h>
+
+struct bcm_ns_usb2 {
+ struct device *dev;
+ struct clk *ref_clk;
+ struct phy *phy;
+ void __iomem *dmu;
+};
+
+static int bcm_ns_usb2_phy_init(struct phy *phy)
+{
+ struct bcm_ns_usb2 *usb2 = phy_get_drvdata(phy);
+ struct device *dev = usb2->dev;
+ void __iomem *dmu = usb2->dmu;
+ u32 ref_clk_rate, usb2ctl, usb_pll_ndiv, usb_pll_pdiv;
+ int err = 0;
+
+ err = clk_prepare_enable(usb2->ref_clk);
+ if (err < 0) {
+ dev_err(dev, "Failed to prepare ref clock: %d\n", err);
+ goto err_out;
+ }
+
+ ref_clk_rate = clk_get_rate(usb2->ref_clk);
+ if (!ref_clk_rate) {
+ dev_err(dev, "Failed to get ref clock rate\n");
+ err = -EINVAL;
+ goto err_clk_off;
+ }
+
+ usb2ctl = readl(dmu + BCMA_DMU_CRU_USB2_CONTROL);
+
+ if (usb2ctl & BCMA_DMU_CRU_USB2_CONTROL_USB_PLL_PDIV_MASK) {
+ usb_pll_pdiv = usb2ctl;
+ usb_pll_pdiv &= BCMA_DMU_CRU_USB2_CONTROL_USB_PLL_PDIV_MASK;
+ usb_pll_pdiv >>= BCMA_DMU_CRU_USB2_CONTROL_USB_PLL_PDIV_SHIFT;
+ } else {
+ usb_pll_pdiv = 1 << 3;
+ }
+
+ /* Calculate ndiv based on a solid 1920 MHz that is for USB2 PHY */
+ usb_pll_ndiv = (1920000000 * usb_pll_pdiv) / ref_clk_rate;
+
+ /* Unlock DMU PLL settings with some magic value */
+ writel(0x0000ea68, dmu + BCMA_DMU_CRU_CLKSET_KEY);
+
+ /* Write USB 2.0 PLL control setting */
+ usb2ctl &= ~BCMA_DMU_CRU_USB2_CONTROL_USB_PLL_NDIV_MASK;
+ usb2ctl |= usb_pll_ndiv << BCMA_DMU_CRU_USB2_CONTROL_USB_PLL_NDIV_SHIFT;
+ writel(usb2ctl, dmu + BCMA_DMU_CRU_USB2_CONTROL);
+
+ /* Lock DMU PLL settings */
+ writel(0x00000000, dmu + BCMA_DMU_CRU_CLKSET_KEY);
+
+err_clk_off:
+ clk_disable_unprepare(usb2->ref_clk);
+err_out:
+ return err;
+}
+
+static const struct phy_ops ops = {
+ .init = bcm_ns_usb2_phy_init,
+ .owner = THIS_MODULE,
+};
+
+static int bcm_ns_usb2_probe(struct platform_device *pdev)
+{
+ struct device *dev = &pdev->dev;
+ struct bcm_ns_usb2 *usb2;
+ struct resource *res;
+ struct phy_provider *phy_provider;
+
+ usb2 = devm_kzalloc(&pdev->dev, sizeof(*usb2), GFP_KERNEL);
+ if (!usb2)
+ return -ENOMEM;
+ usb2->dev = dev;
+
+ res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "dmu");
+ usb2->dmu = devm_ioremap_resource(dev, res);
+ if (IS_ERR(usb2->dmu)) {
+ dev_err(dev, "Failed to map DMU regs\n");
+ return PTR_ERR(usb2->dmu);
+ }
+
+ usb2->ref_clk = devm_clk_get(dev, "phy-ref-clk");
+ if (IS_ERR(usb2->ref_clk)) {
+ dev_err(dev, "Clock not defined\n");
+ return PTR_ERR(usb2->ref_clk);
+ }
+
+ usb2->phy = devm_phy_create(dev, NULL, &ops);
+ if (IS_ERR(dev))
+ return PTR_ERR(dev);
+
+ phy_set_drvdata(usb2->phy, usb2);
+ platform_set_drvdata(pdev, usb2);
+
+ phy_provider = devm_of_phy_provider_register(dev, of_phy_simple_xlate);
+ return PTR_ERR_OR_ZERO(phy_provider);
+}
+
+static const struct of_device_id bcm_ns_usb2_id_table[] = {
+ { .compatible = "brcm,ns-usb2-phy", },
+ {},
+};
+MODULE_DEVICE_TABLE(of, bcm_ns_usb2_id_table);
+
+static struct platform_driver bcm_ns_usb2_driver = {
+ .probe = bcm_ns_usb2_probe,
+ .driver = {
+ .name = "bcm_ns_usb2",
+ .of_match_table = bcm_ns_usb2_id_table,
+ },
+};
+module_platform_driver(bcm_ns_usb2_driver);
+
+MODULE_LICENSE("GPL v2");
diff --git a/include/linux/bcma/bcma.h b/include/linux/bcma/bcma.h
index 0367c63..e6b41f4 100644
--- a/include/linux/bcma/bcma.h
+++ b/include/linux/bcma/bcma.h
@@ -4,6 +4,7 @@
#include <linux/pci.h>
#include <linux/mod_devicetable.h>
+#include <linux/bcma/bcma_driver_arm_c9.h>
#include <linux/bcma/bcma_driver_chipcommon.h>
#include <linux/bcma/bcma_driver_pci.h>
#include <linux/bcma/bcma_driver_pcie2.h>
diff --git a/include/linux/bcma/bcma_driver_arm_c9.h b/include/linux/bcma/bcma_driver_arm_c9.h
new file mode 100644
index 0000000..93bd73d
--- /dev/null
+++ b/include/linux/bcma/bcma_driver_arm_c9.h
@@ -0,0 +1,15 @@
+#ifndef LINUX_BCMA_DRIVER_ARM_C9_H_
+#define LINUX_BCMA_DRIVER_ARM_C9_H_
+
+/* DMU (Device Management Unit) */
+#define BCMA_DMU_CRU_USB2_CONTROL 0x0164
+#define BCMA_DMU_CRU_USB2_CONTROL_USB_PLL_NDIV_MASK 0x00000FFC
+#define BCMA_DMU_CRU_USB2_CONTROL_USB_PLL_NDIV_SHIFT 2
+#define BCMA_DMU_CRU_USB2_CONTROL_USB_PLL_PDIV_MASK 0x00007000
+#define BCMA_DMU_CRU_USB2_CONTROL_USB_PLL_PDIV_SHIFT 12
+#define BCMA_DMU_CRU_CLKSET_KEY 0x0180
+#define BCMA_DMU_CRU_STRAPS_CTRL 0x02A0
+#define BCMA_DMU_CRU_STRAPS_CTRL_USB3 0x00000010
+#define BCMA_DMU_CRU_STRAPS_CTRL_4BYTE 0x00008000
+
+#endif /* LINUX_BCMA_DRIVER_ARM_C9_H_ */
--
1.7.9.5
Powered by blists - more mailing lists