| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Date: Wed, 18 May 2016 18:03:23 +0200
From: Alexander Stein <alexander.stein@...tec-electronic.com>
To: Florian Fainelli <f.fainelli@...il.com>
Cc: Alexander Stein <alexander.stein@...tec-electronic.com>,
netdev@...r.kernel.org, linux-kernel@...r.kernel.org
Subject: [PATCH 1/1 RFC] net/phy: Add Lantiq PHY driver
This currently only supports PEF7071 and allows to specify max-speed and
is able to read the LED configuration from device-tree.
Signed-off-by: Alexander Stein <alexander.stein@...tec-electronic.com>
---
The main purpose for now is to set a LED configuration from device tree and
to limit the maximum speed. The latter one in my case hardware limited.
As MAC and it's link partner support 1000MBit/s they would try to use that
but will eventually fail due to magnetics only supporting 100MBit/s. So
limit the maximum link speed supported directly from the start.
As this is a RFC I skipped the device tree binding doc.
drivers/net/phy/Kconfig | 5 ++
drivers/net/phy/Makefile | 1 +
drivers/net/phy/lantiq.c | 167 +++++++++++++++++++++++++++++++++++++++++++++++
3 files changed, 173 insertions(+)
create mode 100644 drivers/net/phy/lantiq.c
diff --git a/drivers/net/phy/Kconfig b/drivers/net/phy/Kconfig
index 3e28f7a..c004885 100644
--- a/drivers/net/phy/Kconfig
+++ b/drivers/net/phy/Kconfig
@@ -119,6 +119,11 @@ config STE10XP
---help---
This is the driver for the STe100p and STe101p PHYs.
+config LANTIQ_PHY
+ tristate "Driver for Lantiq PHYs"
+ ---help---
+ Supports the PEF7071 PHYs.
+
config LSI_ET1011C_PHY
tristate "Driver for LSI ET1011C PHY"
---help---
diff --git a/drivers/net/phy/Makefile b/drivers/net/phy/Makefile
index 8ad4ac6..e886549 100644
--- a/drivers/net/phy/Makefile
+++ b/drivers/net/phy/Makefile
@@ -38,3 +38,4 @@ obj-$(CONFIG_MDIO_SUN4I) += mdio-sun4i.o
obj-$(CONFIG_MDIO_MOXART) += mdio-moxart.o
obj-$(CONFIG_AMD_XGBE_PHY) += amd-xgbe-phy.o
obj-$(CONFIG_MDIO_BCM_UNIMAC) += mdio-bcm-unimac.o
+obj-$(CONFIG_LANTIQ_PHY) += lantiq.o
diff --git a/drivers/net/phy/lantiq.c b/drivers/net/phy/lantiq.c
new file mode 100644
index 0000000..876a7d1
--- /dev/null
+++ b/drivers/net/phy/lantiq.c
@@ -0,0 +1,167 @@
+/*
+ * Driver for Lantiq PHYs
+ *
+ * Author: Alexander Stein <alexander.stein@...tec-electronic.com>
+ *
+ * Copyright (c) 2015-2016 SYS TEC electronic GmbH
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License as published by the
+ * Free Software Foundation; either version 2 of the License, or (at your
+ * option) any later version.
+ *
+ */
+
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/phy.h>
+#include <linux/of.h>
+
+#define PHY_ID_PEF7071 0xd565a401
+
+#define MII_LANTIQ_MMD_CTRL_REG 0x0d
+#define MII_LANTIQ_MMD_REGDATA_REG 0x0e
+#define OP_DATA 1
+
+struct lantiqphy_led_ctrl {
+ const char *property;
+ u32 regnum;
+};
+
+static int lantiq_extended_write(struct phy_device *phydev,
+ u8 mode, u32 dev_addr, u32 regnum, u16 val)
+{
+ phy_write(phydev, MII_LANTIQ_MMD_CTRL_REG, dev_addr);
+ phy_write(phydev, MII_LANTIQ_MMD_REGDATA_REG, regnum);
+ phy_write(phydev, MII_LANTIQ_MMD_CTRL_REG, (mode << 14) | dev_addr);
+ return phy_write(phydev, MII_LANTIQ_MMD_REGDATA_REG, val);
+}
+
+static int lantiq_of_load_led_config(struct phy_device *phydev,
+ struct device_node *of_node,
+ const struct lantiqphy_led_ctrl *leds,
+ u8 entries)
+{
+ u16 val;
+ int i;
+ int ret = 0;
+
+ for (i = 0; i < entries; i++) {
+ if (!of_property_read_u16(of_node, leds[i].property, &val)) {
+ ret = lantiq_extended_write(phydev, OP_DATA, 0x1f,
+ leds[i].regnum, val);
+ if (ret) {
+ dev_err(&phydev->dev, "Error writing register 0x1f.%04x (%d)\n",
+ leds[i].regnum, ret);
+ break;
+ }
+ }
+ }
+
+ return ret;
+}
+
+static const struct lantiqphy_led_ctrl leds[] = {
+ {
+ .property = "led0h",
+ .regnum = 0x01e2,
+ },
+ {
+ .property = "led0l",
+ .regnum = 0x01e3,
+ },
+ {
+ .property = "led1h",
+ .regnum = 0x01e4,
+ },
+ {
+ .property = "led1l",
+ .regnum = 0x01e5,
+ },
+ {
+ .property = "led2h",
+ .regnum = 0x01e6,
+ },
+ {
+ .property = "led2l",
+ .regnum = 0x01e7,
+ },
+};
+
+static int lantiqphy_config_init(struct phy_device *phydev)
+{
+ struct device *dev = &phydev->dev;
+ struct device_node *of_node = dev->of_node;
+ u32 max_speed;
+
+ if (!of_node && dev->parent->of_node)
+ of_node = dev->parent->of_node;
+
+ if (of_node) {
+ lantiq_of_load_led_config(phydev, of_node, leds,
+ ARRAY_SIZE(leds));
+
+ if (!of_property_read_u32(of_node, "max-speed",
+ &max_speed)) {
+ /* The default values for phydev->supported are
+ * provided by the PHY driver "features" member,
+ * we want to reset to sane defaults fist before
+ * supporting higher speeds.
+ */
+ phydev->supported &= PHY_DEFAULT_FEATURES;
+
+ switch (max_speed) {
+ default:
+ break;
+
+ case SPEED_1000:
+ phydev->supported |= PHY_1000BT_FEATURES;
+ case SPEED_100:
+ phydev->supported |= PHY_100BT_FEATURES;
+ case SPEED_10:
+ phydev->supported |= PHY_10BT_FEATURES;
+ }
+ }
+ }
+ return 0;
+}
+
+static struct phy_driver lantiqphy_driver[] = {
+{
+ .phy_id = PHY_ID_PEF7071,
+ .phy_id_mask = 0x00fffffe,
+ .name = "Lantiq PEF7071",
+ .features = (PHY_GBIT_FEATURES | SUPPORTED_Pause),
+ .flags = PHY_HAS_MAGICANEG,
+ .config_init = lantiqphy_config_init,
+ .config_aneg = genphy_config_aneg,
+ .read_status = genphy_read_status,
+ .suspend = genphy_suspend,
+ .resume = genphy_resume,
+ .driver = { .owner = THIS_MODULE,},
+} };
+
+static int __init lantiqphy_init(void)
+{
+ return phy_drivers_register(lantiqphy_driver,
+ ARRAY_SIZE(lantiqphy_driver));
+}
+
+static void __exit lantiqphy_exit(void)
+{
+ phy_drivers_unregister(lantiqphy_driver,
+ ARRAY_SIZE(lantiqphy_driver));
+}
+
+module_init(lantiqphy_init);
+module_exit(lantiqphy_exit);
+
+MODULE_DESCRIPTION("Lantiq PHY driver");
+MODULE_AUTHOR("Alexander Stein <alexander.stein@...tec-electronic.com>");
+MODULE_LICENSE("GPL");
+
+static struct mdio_device_id __maybe_unused lantiq_tbl[] = {
+ { PHY_ID_PEF7071, 0x00fffffe },
+ { }
+};
+MODULE_DEVICE_TABLE(mdio, lantiq_tbl);
--
2.7.3
Powered by blists - more mailing lists