Message-Id: <1464853811-15233-4-git-send-email-wens@csie.org>
Date:	Thu,  2 Jun 2016 15:50:11 +0800
From:	Chen-Yu Tsai <wens@...e.org>
To:	Maxime Ripard <maxime.ripard@...e-electrons.com>
Cc:	Chen-Yu Tsai <wens@...e.org>, linux-arm-kernel@...ts.infradead.org,
	linux-kernel@...r.kernel.org, linux-sunxi@...glegroups.com
Subject: [PATCH 3/3] ARM: dts: sun8i-h3: Add dts file for Sinovoip BPI-M2+

The BPI-M2+ is an H3 development board. It is a smaller form factor than
the original BPI-M2, with the new H3 SoC.

It has 1GB DRAM, 8GB eMMC, a micro SD card slot, HDMI output, 2 USB
host connector and 1 USB OTG connector, an IR receiver, WiFi+BT based
on Ampak AP6212.

The board also has a 3 pin header for (debug) UART, a 40 pin GPIO header
based on the Raspberry Pi B+, but the peripheral signals are not the
same, and an FPC connector for connecting BPI's camera.

Signed-off-by: Chen-Yu Tsai <wens@...e.org>
---
 arch/arm/boot/dts/Makefile                         |   3 +-
 .../arm/boot/dts/sun8i-h3-sinovoip-bpi-m2-plus.dts | 196 +++++++++++++++++++++
 2 files changed, 198 insertions(+), 1 deletion(-)
 create mode 100644 arch/arm/boot/dts/sun8i-h3-sinovoip-bpi-m2-plus.dts

diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index 06b6c2d695bf..970e9064f56d 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -765,7 +765,8 @@ dtb-$(CONFIG_MACH_SUN8I) += \
 	sun8i-h3-orangepi-2.dtb \
 	sun8i-h3-orangepi-one.dtb \
 	sun8i-h3-orangepi-pc.dtb \
-	sun8i-h3-orangepi-plus.dtb
+	sun8i-h3-orangepi-plus.dtb \
+	sun8i-h3-sinovoip-bpi-m2-plus.dtb
 dtb-$(CONFIG_MACH_SUN9I) += \
 	sun9i-a80-optimus.dtb \
 	sun9i-a80-cubieboard4.dtb
diff --git a/arch/arm/boot/dts/sun8i-h3-sinovoip-bpi-m2-plus.dts b/arch/arm/boot/dts/sun8i-h3-sinovoip-bpi-m2-plus.dts
new file mode 100644
index 000000000000..8a19b4b44f1f
--- /dev/null
+++ b/arch/arm/boot/dts/sun8i-h3-sinovoip-bpi-m2-plus.dts
@@ -0,0 +1,196 @@
+/*
+ * Copyright (C) 2016 Chen-Yu Tsai <wens@...e.org>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ *  a) This file is free software; you can redistribute it and/or
+ *     modify it under the terms of the GNU General Public License as
+ *     published by the Free Software Foundation; either version 2 of the
+ *     License, or (at your option) any later version.
+ *
+ *     This file is distributed in the hope that it will be useful,
+ *     but WITHOUT ANY WARRANTY; without even the implied warranty of
+ *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ *     GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ *  b) Permission is hereby granted, free of charge, to any person
+ *     obtaining a copy of this software and associated documentation
+ *     files (the "Software"), to deal in the Software without
+ *     restriction, including without limitation the rights to use,
+ *     copy, modify, merge, publish, distribute, sublicense, and/or
+ *     sell copies of the Software, and to permit persons to whom the
+ *     Software is furnished to do so, subject to the following
+ *     conditions:
+ *
+ *     The above copyright notice and this permission notice shall be
+ *     included in all copies or substantial portions of the Software.
+ *
+ *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ *     OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+#include "sun8i-h3.dtsi"
+#include "sunxi-common-regulators.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/pinctrl/sun4i-a10.h>
+
+/ {
+	model = "Sinovoip BPI-M2+";
+	compatible = "sinovoip,bpi-m2+", "allwinner,sun8i-h3";
+
+	aliases {
+		serial0 = &uart0;
+		serial1 = &uart1;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	leds {
+		compatible = "gpio-leds";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pwr_led_bpi_m2p>;
+
+		pwr_led {
+			label = "orangepi:green:pwr";
+			gpios = <&r_pio 0 10 GPIO_ACTIVE_HIGH>; /* PL10 */
+			default-state = "on";
+		};
+	};
+
+	gpio_keys {
+		compatible = "gpio-keys";
+		pinctrl-names = "default";
+		pinctrl-0 = <&sw_r_bpi_m2p>;
+
+		sw4 {
+			label = "sw4";
+			linux,code = <BTN_0>;
+			gpios = <&r_pio 0 3 GPIO_ACTIVE_LOW>;
+		};
+	};
+
+	wifi_pwrseq: wifi_pwrseq {
+		compatible = "mmc-pwrseq-simple";
+		pinctrl-names = "default";
+		pinctrl-0 = <&wifi_en_bpi_m2p>;
+		reset-gpios = <&r_pio 0 7 GPIO_ACTIVE_LOW>; /* PL7 */
+	};
+};
+
+&ehci1 {
+	status = "okay";
+};
+
+&ehci2 {
+	status = "okay";
+};
+
+&ir {
+	pinctrl-names = "default";
+	pinctrl-0 = <&ir_pins_a>;
+	status = "okay";
+};
+
+&mmc0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin>;
+	vmmc-supply = <&reg_vcc3v3>;
+	bus-width = <4>;
+	cd-gpios = <&pio 5 6 GPIO_ACTIVE_HIGH>; /* PF6 */
+	cd-inverted;
+	status = "okay";
+};
+
+&mmc1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc1_pins_a>;
+	vmmc-supply = <&reg_vcc3v3>;
+	vqmmc-supply = <&reg_vcc3v3>;
+	mmc-pwrseq = <&wifi_pwrseq>;
+	bus-width = <4>;
+	non-removable;
+	status = "okay";
+
+	brcmf: bcrmf@1 {
+		reg = <1>;
+		compatible = "brcm,bcm4329-fmac";
+		interrupt-parent = <&pio>;
+		interrupts = <6 10 IRQ_TYPE_LEVEL_LOW>; /* PG10 / EINT10 */
+		interrupt-names = "host-wake";
+	};
+};
+
+&mmc2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc2_8bit_pins>;
+	vmmc-supply = <&reg_vcc3v3>;
+	vqmmc-supply = <&reg_vcc3v3>;
+	bus-width = <8>;
+	non-removable;
+	status = "okay";
+};
+
+&ohci1 {
+	status = "okay";
+};
+
+&ohci2 {
+	status = "okay";
+};
+
+&r_pio {
+	pwr_led_bpi_m2p: led_pins@0 {
+		allwinner,pins = "PL10";
+		allwinner,function = "gpio_out";
+		allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+		allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+	};
+
+	sw_r_bpi_m2p: key_pins@0 {
+		allwinner,pins = "PL3";
+		allwinner,function = "gpio_in";
+		allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+		allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+	};
+
+	wifi_en_bpi_m2p: wifi_en_pin {
+		allwinner,pins = "PL7";
+		allwinner,function = "gpio_out";
+		allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+		allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+	};
+};
+
+&uart0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart0_pins_a>;
+	status = "okay";
+};
+
+&uart1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart1_pins_a>;
+	status = "okay";
+};
+
+&usbphy {
+	/* USB VBUS is on as long as VCC-IO is on */
+	status = "okay";
+};
+
-- 
2.8.1

Powered by blists - more mailing lists