Message-ID: <57519FA3.9010208@ti.com>
Date:	Fri, 3 Jun 2016 10:17:55 -0500
From:	"Andrew F. Davis" <afd@...com>
To:	Laxman Dewangan <ldewangan@...dia.com>,
	Guenter Roeck <linux@...ck-us.net>,
	Jonathan Cameron <jic23@...nel.org>, <robh+dt@...nel.org>,
	<corbet@....net>, <lars@...afoo.de>
CC:	<devicetree@...r.kernel.org>, <linux-kernel@...r.kernel.org>,
	<linux-doc@...r.kernel.org>, <linux-iio@...r.kernel.org>,
	<linux-hwmon@...r.kernel.org>, Jean Delvare <khali@...ux-fr.org>
Subject: Re: [PATCH 2/3] iio: adc: ina3221: Add support for IIO ADC driver for
 TI INA3221

On 06/03/2016 09:14 AM, Laxman Dewangan wrote:
> 
> On Friday 03 June 2016 06:59 PM, Guenter Roeck wrote:
>> On 06/03/2016 03:06 AM, Jonathan Cameron wrote:
>>> On 01/06/16 13:34, Laxman Dewangan wrote:
>>>> The INA3221 is a three-channel, high-side current and bus voltage
>>>> monitor
>>>> with an I2C interface from Texas Instruments. The INA3221 monitors both
>>>> shunt voltage drops and bus supply voltages in addition to having
>>>> programmable conversion times and averaging modes for these signals.
>>>> The INA3221 offers both critical and warning alerts to detect multiple
>>>> programmable out-of-range conditions for each channel.
>>>>
>>>> Add support for INA3221 SW driver via IIO ADC interface. The device is
>>>> register as iio-device and provides interface for voltage/current
>>>> and power
>>>> monitor. Also provide interface for setting oneshot/continuous mode and
>>>> critical/warning threshold for the shunt voltage drop.
>>>>
>>>> Signed-off-by: Laxman Dewangan <ldewangan@...dia.com>
>>> Hi Laxman,
>>>
>>> As ever with any driver lying on the border of IIO and hwmon, please
>>> include
>>> a short justification of why you need an IIO driver and also cc the
>>> hwmon list + maintainers. (cc'd on this reply).
>>>
>>> I simply won't take a driver where the hwmon maintainers aren't happy.
>>> As it stands I'm not seeing obvious reasons in the code for why this
>>> should be an IIO device.
>>>
>>
>> Me not either.
>>
>> I have a hwmon driver for the same chip pending from Andrew Davis (TI)
>> which I am just about to accept. We had directed Andrew back in April
>> to write a hwmon driver for the chip, which he did.
>>
> 
> Thanks Guenter,  I found the series
> 
> [PATCH v2 0/2] Add support for INA3221 Triple Current/Voltage Monitors
> Looks fine to me. I can use the hwmon.
> 

If you search even further back you can see I originally went with an
IIO driver as well, comparing the IIO and hwmon version for the simple
use cases I needed the hwmod version turned out much simpler, so it was
probably the right framework for now.

> 
> However, some of the stuff from my patch are not there which I will add
> later once original patch applied:
> - Dynamic mode changes for continuous and one-shot from sysfs.
> - In one shot, when try to read voltage data, do conversion and then read.
> 

My attempt is rather minimal, to be honest I like your stab at this
driver better in some ways, especially relating to DT putting each
channel in its own node with labels, I think this is a bit more clean
and will be more extendable if/when new multi-channel monitor chips are
made.

> Not sure whether exporting the following will help or not. Can you
> please confirm?
> - Oversampling time i.e. average sample
> - conversion time for bus voltage and shunt voltage if default is not
> suited for system.
> 
> 

These can always be added as needed, but the DT changes are not as easy.
I would like it if this got in this cycle but if you think something
will be needed to help your improvements, that can not be added
incrementally, it would probably be best to get them into the initial DT
binding doc now.

Thanks,
Andrew

> 
> 

Powered by blists - more mailing lists