lists.openwall.net   lists  /  announce  owl-users  owl-dev  john-users  john-dev  passwdqc-users  yescrypt  popa3d-users  /  oss-security  kernel-hardening  musl  sabotage  tlsify  passwords  /  crypt-dev  xvendor  /  Bugtraq  Full-Disclosure  linux-kernel  linux-netdev  linux-ext4  linux-hardening  linux-cve-announce  PHC 
Open Source and information security mailing list archives
 
Hash Suite: Windows password security audit tool. GUI, reports in PDF.
[<prev] [next>] [<thread-prev] [thread-next>] [day] [month] [year] [list]
Message-ID: <20160607212016.GH56933@redhat.com>
Date:	Tue, 7 Jun 2016 17:20:16 -0400
From:	Jarod Wilson <jarod@...hat.com>
To:	Bert Kenward <bkenward@...arflare.com>
Cc:	linux-kernel@...r.kernel.org,
	Solarflare linux maintainers <linux-net-drivers@...arflare.com>,
	Edward Cree <ecree@...arflare.com>,
	David Miller <davem@...emloft.net>, netdev@...r.kernel.org
Subject: Re: [PATCH net v2] sfc: report supported link speeds on SFP
 connections

On Mon, Jun 06, 2016 at 02:55:29PM -0400, Jarod Wilson wrote:
> On Mon, Jun 06, 2016 at 05:29:30PM +0100, Bert Kenward wrote:
> > 7000-series SFC NICs connected with an SFP+ module currently fail to
> > report any supported link speeds.
> > 
> > Reported-by: Jarod Wilson <jarod@...hat.com>
> > Signed-off-by: Bert Kenward <bkenward@...arflare.com>
> 
> Had a feeling my cut might not have been quite right. Looks good to me.
> 
> Reviewed-by: Jarod Wilson <jarod@...hat.com>

...however, upon testing, there's a gotcha. This results in my 10Gbps sfc
nic reporting that it supports 40Gbps:

$ ethtool ens4f0
Settings for ens4f0:
	Supported ports: [ FIBRE ]
	Supported link modes:   1000baseT/Full
	                        10000baseT/Full
	                        40000baseKR4/Full
	Supported pause frame use: Symmetric Receive-only
	Supports auto-negotiation: Yes
	Advertised link modes:  Not reported
	Advertised pause frame use: Symmetric
	Advertised auto-negotiation: Yes
	Link partner advertised link modes:  10000baseT/Full
	Link partner advertised pause frame use: Symmetric
	Link partner advertised auto-negotiation: No
	Speed: 10000Mb/s
	Duplex: Full
	Port: FIBRE
	PHYAD: 255
	Transceiver: internal
	Auto-negotiation: on
Cannot get wake-on-lan settings: Operation not permitted
	Current message level: 0x000020f7 (8439)
			       drv probe link ifdown ifup rx_err tx_err hw
	Link detected: yes

$ ethtool -i ens4f0
driver: sfc
version: 4.0
firmware-version: 4.6.1.1001 rx1 tx1
expansion-rom-version:
bus-info: 0000:05:00.0
supports-statistics: yes
supports-test: yes
supports-eeprom-access: no
supports-register-dump: yes
supports-priv-flags: no

$ lspci -v -s 0000:05:00.0
05:00.0 Ethernet controller: Solarflare Communications SFC9120 (rev 01)
	Subsystem: Solarflare Communications SFN7x22F-R2 Flareon Ultra 7000 Series 10G Adapter
	Physical Slot: 4
	Flags: bus master, fast devsel, latency 0, IRQ 16
	I/O ports at c100 [size=256]
	Memory at ef000000 (64-bit, non-prefetchable) [size=8M]
	Memory at ef884000 (64-bit, non-prefetchable) [size=16K]
	Expansion ROM at ef840000 [disabled] [size=256K]
	Capabilities: <access denied>
	Kernel driver in use: sfc

One solution would be to move the case MC_CMD_MEDIA_QSFP_PLUS above
XFP/SFP_PLUS, only check the 40Gbps cap, no break, fall through into the
XFP/SFP_PLUS chunk, continue processing there.

-- 
Jarod Wilson
jarod@...hat.com

Powered by blists - more mailing lists

Powered by Openwall GNU/*/Linux Powered by OpenVZ