linux-kernel - Re: [PATCHv3] wlcore: spi: add wl18xx support

lists.openwall.net		lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC
Open Source and information security mailing list archives

Hash Suite: Windows password security audit tool. GUI, reports in PDF.

[<prev] [next>] [<thread-prev] [thread-next>] [day] [month] [year] [list]

Message-ID: <20160621215703.GA14228@rob-hp-laptop>
Date:	Tue, 21 Jun 2016 16:57:03 -0500
From:	Rob Herring <robh@...nel.org>
To:	"Reizer, Eyal" <eyalr@...com>
Cc:	"kvalo@...eaurora.org" <kvalo@...eaurora.org>,
	"linux-wireless@...r.kernel.org" <linux-wireless@...r.kernel.org>,
	"netdev@...r.kernel.org" <netdev@...r.kernel.org>,
	"linux-kernel@...r.kernel.org" <linux-kernel@...r.kernel.org>,
	"devicetree@...r.kernel.org" <devicetree@...r.kernel.org>,
	"linux-spi@...r.kernel.org" <linux-spi@...r.kernel.org>,
	Mark Brown <broonie@...nel.org>
Subject: Re: [PATCHv3] wlcore: spi: add wl18xx support

On Tue, Jun 21, 2016 at 12:02:06PM +0000, Reizer, Eyal wrote:
> Add support for using with both wl12xx and wl18xx.
> 
> - all wilink family needs special init command for entering wspi mode.
>   extra clock cycles should be sent after the spi init command while the
>   cs pin is high.
> - Use inverted chip select for sending a dummy 4 bytes command that
>   completes the init stage and puts the wilink chip into wspi mode.
> 
> Signed-off-by: Eyal Reizer <eyalr@...com>
> ---
> v1->v2:update device tree bindings configuration
> v2->v3:revert from manual gpio manipulation. use inverted chip select instead
> for sending the extra init cycle, which achieves the same hardware purpose.
> update device tree bindings docucmentation accordingly
> 
>  .../bindings/net/wireless/ti,wlcore,spi.txt        |  47 ++++++--
>  drivers/net/wireless/ti/wlcore/spi.c               | 124 +++++++++++++++++----
>  2 files changed, 145 insertions(+), 26 deletions(-)
> 
> diff --git a/Documentation/devicetree/bindings/net/wireless/ti,wlcore,spi.txt b/Documentation/devicetree/bindings/net/wireless/ti,wlcore,spi.txt
> index 9180724..35467cf 100644
> --- a/Documentation/devicetree/bindings/net/wireless/ti,wlcore,spi.txt
> +++ b/Documentation/devicetree/bindings/net/wireless/ti,wlcore,spi.txt
> @@ -1,19 +1,30 @@
> -* Texas Instruments wl1271 wireless lan controller
> +* Texas Instruments wl12xx/wl18xx wireless lan controller
>  
> -The wl1271 chip can be connected via SPI or via SDIO. This
> +The wl12xx/wl18xx chips can be connected via SPI or via SDIO. This
>  document describes the binding for the SPI connected chip.
>  
>  Required properties:
> -- compatible :          Should be "ti,wl1271"
> +- compatible :          Should be one of the following:
> +    * "ti,wl1271"
> +    * "ti,wl1273"
> +    * "ti,wl1281"
> +    * "ti,wl1283"
> +    * "ti,wl1801"
> +    * "ti,wl1805"
> +    * "ti,wl1807"
> +    * "ti,wl1831"
> +    * "ti,wl1835"
> +    * "ti,wl1837"
>  - reg :                 Chip select address of device
>  - spi-max-frequency :   Maximum SPI clocking speed of device in Hz
> -- ref-clock-frequency : Reference clock frequency
>  - interrupt-parent, interrupts :
>                          Should contain parameters for 1 interrupt line.
>                          Interrupt parameters: parent, line number, type.
> -- vwlan-supply :        Point the node of the regulator that powers/enable the wl1271 chip
> +- vwlan-supply :        Point the node of the regulator that powers/enable the
> +                        wl12xx/wl18xx chip
>  
>  Optional properties:
> +- ref-clock-frequency : Reference clock frequency (should be set for wl12xx)
>  - clock-xtal :          boolean, clock is generated from XTAL
>  
>  - Please consult Documentation/devicetree/bindings/spi/spi-bus.txt
> @@ -21,10 +32,15 @@ Optional properties:
>  
>  Examples:
>  
> +For wl12xx family:
>  &spi1 {
> -	wl1271@1 {
> +	status = "okay";
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&spi1_pins>;
> +	#address-cells = <1>;
> +	#size-cells = <0>;

None of this is really relevant to this binding.

> +	wlcore: wlcore@0 {

Now your unit-address and reg value don't match.

>  		compatible = "ti,wl1271";
> -
>  		reg = <1>;
>  		spi-max-frequency = <48000000>;
>  		clock-xtal;
> @@ -34,3 +50,20 @@ Examples:
>  		vwlan-supply = <&vwlan_fixed>;
>  	};
>  };
> +
> +For wl18xx family:
> +&spi0	{
> +	status = "okay";
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&spi0_pins>;
> +	#address-cells = <1>;
> +	#size-cells = <0>;
> +	wlcore: wlcore@0 {
> +		compatible = "ti,wl1835";
> +		vwlan-supply = <&wlan_en_reg>;
> +		spi-max-frequency = <48000000>;
> +		reg = <0>;
> +		interrupt-parent = <&gpio0>;
> +		interrupts = <27 IRQ_TYPE_EDGE_RISING>;
> +	};
> +};