[<prev] [next>] [<thread-prev] [thread-next>] [day] [month] [year] [list]
Message-ID: <20160716225715.GA27724@rob-hp-laptop>
Date: Sat, 16 Jul 2016 17:57:15 -0500
From: Rob Herring <robh@...nel.org>
To: William Wu <william.wu@...k-chips.com>
Cc: gregkh@...uxfoundation.org, balbi@...nel.org, heiko@...ech.de,
linux-rockchip@...ts.infradead.org, briannorris@...gle.com,
dianders@...gle.com, kever.yang@...k-chips.com,
huangtao@...k-chips.com, frank.wang@...k-chips.com,
eddie.cai@...k-chips.com, John.Youn@...opsys.com,
linux-kernel@...r.kernel.org, linux-usb@...r.kernel.org,
sergei.shtylyov@...entembedded.com, mark.rutland@....com,
devicetree@...r.kernel.org
Subject: Re: [PATCH v7 3/5] usb: dwc3: make usb2 phy utmi interface
configurable in DT
On Thu, Jul 14, 2016 at 04:59:20PM +0800, William Wu wrote:
> Add snps,phyif-utmi-width devicetree property to configure
> the UTMI+ PHY with an 8- or 16-bit interface. UTMI+ PHY
> interface is a hardware property, and it's platform dependent.
> Normally,the PHYIF can be configured during coreconsultant.
^
space
> But for some specific USB cores(e.g. rk3399 SoC DWC3), the
> default PHYIF configuration value is fault, so we need to
> reconfigure it by software.
>
> And refer to the DWC3 databook, the GUSB2PHYCFG.USBTRDTIM
> must be set to the corresponding value according to the
> UTMI+ PHY interface.
>
> Signed-off-by: William Wu <william.wu@...k-chips.com>
> ---
> Changes in v7:
> - remove quirk and use only one property to configure utmi (Heiko, Rob Herring)
>
> Changes in v6:
> - use '-' instead of '_' in dts (Rob Herring)
>
> Changes in v5:
> - None
>
> Changes in v4:
> - rebase on top of balbi testing/next, remove pdata (balbi)
>
> Changes in v3:
> - None
>
> Changes in v2:
> - add a quirk for phyif_utmi (balbi)
>
> Documentation/devicetree/bindings/usb/dwc3.txt | 3 +++
> drivers/usb/dwc3/core.c | 25 +++++++++++++++++++++++++
> drivers/usb/dwc3/core.h | 10 ++++++++++
> 3 files changed, 38 insertions(+)
>
> diff --git a/Documentation/devicetree/bindings/usb/dwc3.txt b/Documentation/devicetree/bindings/usb/dwc3.txt
> index 020b0e9..00cc541 100644
> --- a/Documentation/devicetree/bindings/usb/dwc3.txt
> +++ b/Documentation/devicetree/bindings/usb/dwc3.txt
> @@ -47,6 +47,9 @@ Optional properties:
> - snps,hird-threshold: HIRD threshold
> - snps,hsphy_interface: High-Speed PHY interface selection between "utmi" for
> UTMI+ and "ulpi" for ULPI when the DWC_USB3_HSPHY_INTERFACE has value 3.
> + - snps,phyif-utmi-width: the value to configure the core to support a UTMI+ PHY
> + with an 8- or 16-bit interface. Value 8 select 8-bit
> + interface, value 16 select 16-bit interface.
Is 'phy_type = "utmi_wide"' not the same as 16-bit width?
Again, I think this should be common.
Rob
Powered by blists - more mailing lists