Message-ID: <8665E2433BC68541A24DFFCA87B70F5B36161990@DFRE01.ent.ti.com>
Date:	Wed, 20 Jul 2016 06:58:12 +0000
From:	"Reizer, Eyal" <eyalr@...com>
To:	Kalle Valo <kvalo@...eaurora.org>
CC:	"linux-wireless@...r.kernel.org" <linux-wireless@...r.kernel.org>,
	"netdev@...r.kernel.org" <netdev@...r.kernel.org>,
	"linux-kernel@...r.kernel.org" <linux-kernel@...r.kernel.org>,
	"devicetree@...r.kernel.org" <devicetree@...r.kernel.org>,
	"linux-spi@...r.kernel.org" <linux-spi@...r.kernel.org>,
	Rob Herring <robh@...nel.org>
Subject: [PATCHv8] wlcore: spi: add wl18xx support

Add support for using with both wl12xx and wl18xx.

- all wilink family needs special init command for entering wspi mode.
  extra clock cycles should be sent after the spi init command while the
  cs pin is high.
- Use inverted chip select for sending a dummy 4 bytes command that
  completes the init stage.

Signed-off-by: Eyal Reizer <eyalr@...com>
Acked-by: Rob Herring <robh@...nel.org>
---
v1->v2:update device tree bindings configuration
v2->v3:revert from manual gpio manipulation. use inverted chip select instead
for sending the extra init cycle which, achieves the same hardware purpose.
update device tree bindings docucmentation accordingly
v3->v4: Remove redundant data form binding documentation and fix chip select
number mismatch in wl1271 example
v4->v5: Rebase on top of head of wireless-drivers-next
v5->v6: Add ACKs
v6->v7: Mail format issues
v7->v8: Remove redundant varaible from wlcore_probe_of
 .../bindings/net/wireless/ti,wlcore,spi.txt        |  41 +++++--
 drivers/net/wireless/ti/wlcore/spi.c               | 124 +++++++++++++++++----
 2 files changed, 137 insertions(+), 28 deletions(-)

diff --git a/Documentation/devicetree/bindings/net/wireless/ti,wlcore,spi.txt b/Documentation/devicetree/bindings/net/wireless/ti,wlcore,spi.txt
index 9180724..8f9ced0 100644
--- a/Documentation/devicetree/bindings/net/wireless/ti,wlcore,spi.txt
+++ b/Documentation/devicetree/bindings/net/wireless/ti,wlcore,spi.txt
@@ -1,19 +1,30 @@
-* Texas Instruments wl1271 wireless lan controller
+* Texas Instruments wl12xx/wl18xx wireless lan controller
 
-The wl1271 chip can be connected via SPI or via SDIO. This
+The wl12xx/wl18xx chips can be connected via SPI or via SDIO. This
 document describes the binding for the SPI connected chip.
 
 Required properties:
-- compatible :          Should be "ti,wl1271"
+- compatible :          Should be one of the following:
+    * "ti,wl1271"
+    * "ti,wl1273"
+    * "ti,wl1281"
+    * "ti,wl1283"
+    * "ti,wl1801"
+    * "ti,wl1805"
+    * "ti,wl1807"
+    * "ti,wl1831"
+    * "ti,wl1835"
+    * "ti,wl1837"
 - reg :                 Chip select address of device
 - spi-max-frequency :   Maximum SPI clocking speed of device in Hz
-- ref-clock-frequency : Reference clock frequency
 - interrupt-parent, interrupts :
                         Should contain parameters for 1 interrupt line.
                         Interrupt parameters: parent, line number, type.
-- vwlan-supply :        Point the node of the regulator that powers/enable the wl1271 chip
+- vwlan-supply :        Point the node of the regulator that powers/enable the
+                        wl12xx/wl18xx chip
 
 Optional properties:
+- ref-clock-frequency : Reference clock frequency (should be set for wl12xx)
 - clock-xtal :          boolean, clock is generated from XTAL
 
 - Please consult Documentation/devicetree/bindings/spi/spi-bus.txt
@@ -21,16 +32,28 @@ Optional properties:
 
 Examples:
 
+For wl12xx family:
 &spi1 {
-	wl1271@1 {
+	wlcore: wlcore@1 {
 		compatible = "ti,wl1271";
-
 		reg = <1>;
 		spi-max-frequency = <48000000>;
-		clock-xtal;
-		ref-clock-frequency = <38400000>;
 		interrupt-parent = <&gpio3>;
 		interrupts = <8 IRQ_TYPE_LEVEL_HIGH>;
 		vwlan-supply = <&vwlan_fixed>;
+		clock-xtal;
+		ref-clock-frequency = <38400000>;
+	};
+};
+
+For wl18xx family:
+&spi0 {
+	wlcore: wlcore@0 {
+		compatible = "ti,wl1835";
+		reg = <0>;
+		spi-max-frequency = <48000000>;
+		interrupt-parent = <&gpio0>;
+		interrupts = <27 IRQ_TYPE_EDGE_RISING>;
+		vwlan-supply = <&vwlan_fixed>;
 	};
 };
diff --git a/drivers/net/wireless/ti/wlcore/spi.c b/drivers/net/wireless/ti/wlcore/spi.c
index cea9443..6d24040 100644
--- a/drivers/net/wireless/ti/wlcore/spi.c
+++ b/drivers/net/wireless/ti/wlcore/spi.c
@@ -70,16 +70,30 @@
 #define WSPI_MAX_CHUNK_SIZE    4092
 
 /*
- * only support SPI for 12xx - this code should be reworked when 18xx
- * support is introduced
+ * wl18xx driver aggregation buffer size is (13 * PAGE_SIZE) compared to
+ * (4 * PAGE_SIZE) for wl12xx, so use the larger buffer needed for wl18xx
  */
-#define SPI_AGGR_BUFFER_SIZE (4 * PAGE_SIZE)
+#define SPI_AGGR_BUFFER_SIZE (13 * PAGE_SIZE)
 
 /* Maximum number of SPI write chunks */
 #define WSPI_MAX_NUM_OF_CHUNKS \
 	((SPI_AGGR_BUFFER_SIZE / WSPI_MAX_CHUNK_SIZE) + 1)
 
 
+struct wilink_familiy_data {
+	char name[8];
+};
+
+const struct wilink_familiy_data *wilink_data;
+
+static const struct wilink_familiy_data wl18xx_data = {
+	.name = "wl18xx",
+};
+
+static const struct wilink_familiy_data wl12xx_data = {
+	.name = "wl12xx",
+};
+
 struct wl12xx_spi_glue {
 	struct device *dev;
 	struct platform_device *core;
@@ -119,6 +133,7 @@ static void wl12xx_spi_init(struct device *child)
 	struct wl12xx_spi_glue *glue = dev_get_drvdata(child->parent);
 	struct spi_transfer t;
 	struct spi_message m;
+	struct spi_device *spi = to_spi_device(glue->dev);
 	u8 *cmd = kzalloc(WSPI_INIT_CMD_LEN, GFP_KERNEL);
 
 	if (!cmd) {
@@ -151,6 +166,7 @@ static void wl12xx_spi_init(struct device *child)
 		cmd[6] |= WSPI_INIT_CMD_EN_FIXEDBUSY;
 
 	cmd[7] = crc7_be(0, cmd+2, WSPI_INIT_CMD_CRC_LEN) | WSPI_INIT_CMD_END;
+
 	/*
 	 * The above is the logical order; it must actually be stored
 	 * in the buffer byte-swapped.
@@ -163,6 +179,28 @@ static void wl12xx_spi_init(struct device *child)
 	spi_message_add_tail(&t, &m);
 
 	spi_sync(to_spi_device(glue->dev), &m);
+
+	/* Send extra clocks with inverted CS (high). this is required
+	 * by the wilink family in order to successfully enter WSPI mode.
+	 */
+	spi->mode ^= SPI_CS_HIGH;
+	memset(&m, 0, sizeof(m));
+	spi_message_init(&m);
+
+	cmd[0] = 0xff;
+	cmd[1] = 0xff;
+	cmd[2] = 0xff;
+	cmd[3] = 0xff;
+	__swab32s((u32 *)cmd);
+
+	t.tx_buf = cmd;
+	t.len = 4;
+	spi_message_add_tail(&t, &m);
+
+	spi_sync(to_spi_device(glue->dev), &m);
+
+	/* Restore chip select configration to normal */
+	spi->mode ^= SPI_CS_HIGH;
 	kfree(cmd);
 }
 
@@ -270,22 +308,25 @@ static int __must_check wl12xx_spi_raw_read(struct device *child, int addr,
 	return 0;
 }
 
-static int __must_check wl12xx_spi_raw_write(struct device *child, int addr,
-					     void *buf, size_t len, bool fixed)
+static int __wl12xx_spi_raw_write(struct device *child, int addr,
+				  void *buf, size_t len, bool fixed)
 {
 	struct wl12xx_spi_glue *glue = dev_get_drvdata(child->parent);
-	/* SPI write buffers - 2 for each chunk */
-	struct spi_transfer t[2 * WSPI_MAX_NUM_OF_CHUNKS];
+	struct spi_transfer *t;
 	struct spi_message m;
 	u32 commands[WSPI_MAX_NUM_OF_CHUNKS]; /* 1 command per chunk */
 	u32 *cmd;
 	u32 chunk_len;
 	int i;
 
+	/* SPI write buffers - 2 for each chunk */
+	t = kzalloc(sizeof(*t) * 2 * WSPI_MAX_NUM_OF_CHUNKS, GFP_KERNEL);
+	if (!t)
+		return -ENOMEM;
+
 	WARN_ON(len > SPI_AGGR_BUFFER_SIZE);
 
 	spi_message_init(&m);
-	memset(t, 0, sizeof(t));
 
 	cmd = &commands[0];
 	i = 0;
@@ -318,9 +359,26 @@ static int __must_check wl12xx_spi_raw_write(struct device *child, int addr,
 
 	spi_sync(to_spi_device(glue->dev), &m);
 
+	kfree(t);
 	return 0;
 }
 
+static int __must_check wl12xx_spi_raw_write(struct device *child, int addr,
+					     void *buf, size_t len, bool fixed)
+{
+	int ret;
+
+	/* The ELP wakeup write may fail the first time due to internal
+	 * hardware latency. It is safer to send the wakeup command twice to
+	 * avoid unexpected failures.
+	 */
+	if (addr == HW_ACCESS_ELP_CTRL_REG)
+		ret = __wl12xx_spi_raw_write(child, addr, buf, len, fixed);
+	ret = __wl12xx_spi_raw_write(child, addr, buf, len, fixed);
+
+	return ret;
+}
+
 /**
  * wl12xx_spi_set_power - power on/off the wl12xx unit
  * @child: wl12xx device handle.
@@ -349,17 +407,38 @@ static int wl12xx_spi_set_power(struct device *child, bool enable)
 	return ret;
 }
 
+/**
+ * wl12xx_spi_set_block_size
+ *
+ * This function is not needed for spi mode, but need to be present.
+ * Without it defined the wlcore fallback to use the wrong packet
+ * allignment on tx.
+ */
+static void wl12xx_spi_set_block_size(struct device *child,
+				      unsigned int blksz)
+{
+}
+
 static struct wl1271_if_operations spi_ops = {
 	.read		= wl12xx_spi_raw_read,
 	.write		= wl12xx_spi_raw_write,
 	.reset		= wl12xx_spi_reset,
 	.init		= wl12xx_spi_init,
 	.power		= wl12xx_spi_set_power,
-	.set_block_size = NULL,
+	.set_block_size = wl12xx_spi_set_block_size,
 };
 
 static const struct of_device_id wlcore_spi_of_match_table[] = {
-	{ .compatible = "ti,wl1271" },
+	{ .compatible = "ti,wl1271", .data = &wl12xx_data},
+	{ .compatible = "ti,wl1273", .data = &wl12xx_data},
+	{ .compatible = "ti,wl1281", .data = &wl12xx_data},
+	{ .compatible = "ti,wl1283", .data = &wl12xx_data},
+	{ .compatible = "ti,wl1801", .data = &wl18xx_data},
+	{ .compatible = "ti,wl1805", .data = &wl18xx_data},
+	{ .compatible = "ti,wl1807", .data = &wl18xx_data},
+	{ .compatible = "ti,wl1831", .data = &wl18xx_data},
+	{ .compatible = "ti,wl1835", .data = &wl18xx_data},
+	{ .compatible = "ti,wl1837", .data = &wl18xx_data},
 	{ }
 };
 MODULE_DEVICE_TABLE(of, wlcore_spi_of_match_table);
@@ -375,18 +454,24 @@ static int wlcore_probe_of(struct spi_device *spi, struct wl12xx_spi_glue *glue,
 			   struct wlcore_platdev_data *pdev_data)
 {
 	struct device_node *dt_node = spi->dev.of_node;
-	int ret;
+	const struct of_device_id *of_id;
+
+	of_id = of_match_node(wlcore_spi_of_match_table, dt_node);
+	if (!of_id)
+		return -ENODEV;
+
+	wilink_data = of_id->data;
+	dev_info(&spi->dev, "selected chip familiy is %s\n",
+		 wilink_data->name);
 
 	if (of_find_property(dt_node, "clock-xtal", NULL))
 		pdev_data->ref_clock_xtal = true;
 
-	ret = of_property_read_u32(dt_node, "ref-clock-frequency",
-				   &pdev_data->ref_clock_freq);
-	if (ret) {
-		dev_err(glue->dev,
-			"can't get reference clock frequency (%d)\n", ret);
-		return ret;
-	}
+	/* optional clock frequency params */
+	of_property_read_u32(dt_node, "ref-clock-frequency",
+			     &pdev_data->ref_clock_freq);
+	of_property_read_u32(dt_node, "tcxo-clock-frequency",
+			     &pdev_data->tcxo_clock_freq);
 
 	return 0;
 }
@@ -437,7 +522,8 @@ static int wl1271_probe(struct spi_device *spi)
 		return ret;
 	}
 
-	glue->core = platform_device_alloc("wl12xx", PLATFORM_DEVID_AUTO);
+	glue->core = platform_device_alloc(wilink_data->name,
+					   PLATFORM_DEVID_AUTO);
 	if (!glue->core) {
 		dev_err(glue->dev, "can't allocate platform_device\n");
 		return -ENOMEM;
-- 
2.7.4

Powered by blists - more mailing lists