linux-kernel - Re: [PATCH 18/18] ARM: mvebu: a395-gp: add support for the Armada 395 GP Board

lists.openwall.net		lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC
Open Source and information security mailing list archives

Hash Suite: Windows password security audit tool. GUI, reports in PDF.

[<prev] [next>] [<thread-prev] [thread-next>] [day] [month] [year] [list]

Date:	Thu, 28 Jul 2016 15:15:46 +0200
From:	Gregory CLEMENT <gregory.clement@...e-electrons.com>
To:	Grzegorz Jaszczyk <jaz@...ihalf.com>
Cc:	devicetree@...r.kernel.org, linux-kernel@...r.kernel.org,
	linux-arm-kernel@...ts.infradead.org, robh+dt@...nel.org,
	mark.rutland@....com, jason@...edaemon.net, andrew@...n.ch,
	sebastian.hesselbarth@...il.com, linux@...linux.org.uk,
	thomas.petazzoni@...e-electrons.com, mw@...ihalf.com,
	alior@...vell.com
Subject: Re: [PATCH 18/18] ARM: mvebu: a395-gp: add support for the Armada 395 GP Board

Hi Grzegorz,
 
 On jeu., juil. 21 2016, Grzegorz Jaszczyk <jaz@...ihalf.com> wrote:

Change the prefix to "ARM: dts: mvebu: armada-395-gp:"

> This commit adds description for the following features for this board:
>
> - Serial port
> - PCIe interfaces
> - USB2.0
> - USB3.0
> - SDIO
> - 1024 MiB NAND-FLASH
> - SATA
> - I2C buses
>
> Signed-off-by: Grzegorz Jaszczyk <jaz@...ihalf.com>
[...]

As for the other board, try to add information about the connector used:

> +			serial@...00 {
Here,

> +				status = "okay";
> +			};
> +
> +			usb@...00 {
here
> +				status = "okay";
> +			};
> +
> +			sata@...00 {
here
> +				status = "okay";
> +			};
> +
> +			flash@...00 {
> +				status = "okay";
> +				pinctrl-0 = <&nand_pins>;
> +				pinctrl-names = "default";
> +				num-cs = <1>;
> +				marvell,nand-keep-config;
> +				marvell,nand-enable-arbiter;
> +				nand-on-flash-bbt;
> +				nand-ecc-strength = <4>;
> +				nand-ecc-step-size = <512>;
> +
> +				partitions {
> +					compatible = "fixed-partitions";
> +					#address-cells = <1>;
> +					#size-cells = <1>;
> +
> +					partition@0 {
> +						label = "U-Boot";
> +						reg = <0x00000000 0x00600000>;
> +						read-only;
> +					};
> +
> +					partition@...000 {
> +						label = "uImage";
> +						reg = <0x00600000 0x00400000>;
> +						read-only;
> +					};
> +
> +					partition@...0000 {
> +						label = "Root";
> +						reg = <0x00a00000 0x3f600000>;
> +					};
> +				};
> +			};
> +
> +			sdhci@...00 {
here
> +				clock-frequency = <200000000>;
> +				broken-cd;
> +				wp-inverted;
> +				bus-width = <8>;
> +				status = "okay";
> +				no-1-8-v;
> +			};
> +
> +			usb3@...00 {
here
> +				status = "okay";
> +			};
> +		};
> +
> +		pcie-controller {
> +			status = "okay";
> +
> +			/*
> +			 * The two PCIe units are accessible through
> +			 * mini PCIe slot on the board.
> +			 */
and here for each slot
> +			pcie@2,0 {
> +				/* Port 1, Lane 0 */
> +				status = "okay";
> +			};
> +
> +			pcie@4,0 {
> +				/* Port 3, Lane 0 */
> +				status = "okay";
> +			};
> +		};
> +	};
> +};

then you can add my:
Acked-by: Gregory CLEMENT <gregory.clement@...e-electrons.com>

Thanks,

Gregory

-- 
Gregory Clement, Free Electrons
Kernel, drivers, real-time and embedded Linux
development, consulting, training and support.
http://free-electrons.com