linux-kernel - Re: [PATCH v3 1/6] binding-doc: power: pwrseq-generic: add binding doc for generic power sequence library

lists.openwall.net		lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC
Open Source and information security mailing list archives

Hash Suite: Windows password security audit tool. GUI, reports in PDF.

[<prev] [next>] [<thread-prev] [thread-next>] [day] [month] [year] [list]

Message-ID: <20160729020917.GB11787@shlinux2>
Date:	Fri, 29 Jul 2016 10:09:17 +0800
From:	Peter Chen <hzpeterchen@...il.com>
To:	Peter Chen <peter.chen@....com>
Cc:	gregkh@...uxfoundation.org, stern@...land.harvard.edu,
	ulf.hansson@...aro.org, broonie@...nel.org, sre@...nel.org,
	robh+dt@...nel.org, shawnguo@...nel.org, dbaryshkov@...il.com,
	dwmw2@...radead.org, mark.rutland@....com,
	devicetree@...r.kernel.org, k.kozlowski@...sung.com,
	stephen.boyd@...aro.org, oscar@...andei.net, arnd@...db.de,
	pawel.moll@....com, linux-pm@...r.kernel.org,
	linux-kernel@...r.kernel.org, s.hauer@...gutronix.de,
	linux-usb@...r.kernel.org, mail@...iej.szmigiero.name,
	troy.kisky@...ndarydevices.com, stillcompiling@...il.com,
	p.zabel@...gutronix.de, festevam@...il.com,
	linux-arm-kernel@...ts.infradead.org
Subject: Re: [PATCH v3 1/6] binding-doc: power: pwrseq-generic: add binding
 doc for generic power sequence library

On Wed, Jul 20, 2016 at 05:40:24PM +0800, Peter Chen wrote:
> Add binding doc for generic power sequence library.
> 
> Signed-off-by: Peter Chen <peter.chen@....com>
> Acked-by: Philipp Zabel <p.zabel@...gutronix.de>
> ---
>  .../bindings/power/pwrseq/pwrseq-generic.txt       | 48 ++++++++++++++++++++++
>  1 file changed, 48 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/power/pwrseq/pwrseq-generic.txt
> 
> diff --git a/Documentation/devicetree/bindings/power/pwrseq/pwrseq-generic.txt b/Documentation/devicetree/bindings/power/pwrseq/pwrseq-generic.txt
> new file mode 100644
> index 0000000..48bb3e1
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/power/pwrseq/pwrseq-generic.txt
> @@ -0,0 +1,48 @@
> +The generic power sequence library
> +
> +Some hard-wired devices (eg USB/MMC) need to do power sequence before
> +the device can be enumerated on the bus, the typical power sequence
> +like: enable USB PHY clock, toggle reset pin, etc. But current
> +Linux device driver lacks of such code to do it, it may cause some
> +hard-wired devices works abnormal or can't be recognized by
> +controller at all. The power sequence will be done before this device
> +can be found at the bus.
> +
> +The power sequence properties is under the device node.
> +
> +Optional properties:
> +- clocks: the input clock for device.
> +- reset-gpios: Should specify the GPIO for reset.
> +- reset-duration-us: the duration in microsecond for assert reset signal.
> +
> +Below is the example of USB power sequence properties on USB device
> +nodes which have two level USB hubs.
> +
> +&usbotg1 {
> +	vbus-supply = <&reg_usb_otg1_vbus>;
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pinctrl_usb_otg1_id>;
> +	status = "okay";
> +
> +	#address-cells = <1>;
> +	#size-cells = <0>;
> +	genesys: hub@1 {
> +		compatible = "usb5e3,608";
> +		reg = <1>;
> +
> +		clocks = <&clks IMX6SX_CLK_CKO>;
> +		reset-gpios = <&gpio4 5 GPIO_ACTIVE_LOW>; /* hub reset pin */
> +		reset-duration-us = <10>;
> +
> +		#address-cells = <1>;
> +		#size-cells = <0>;
> +		asix: ethernet@1 {
> +			compatible = "usbb95,1708";
> +			reg = <1>;
> +
> +			clocks = <&clks IMX6SX_CLK_IPG>;
> +			reset-gpios = <&gpio4 6 GPIO_ACTIVE_LOW>; /* ethernet_rst */
> +			reset-duration-us = <15>;
> +		};
> +	};
> +};
> -- 
> 1.9.1

Rob, would you please help to ack dts changes in this series if you are
ok with them?

-- 

Best Regards,
Peter Chen