| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-Id: <1472015825-11365-2-git-send-email-zyw@rock-chips.com>
Date: Tue, 23 Aug 2016 22:17:01 -0700
From: Chris Zhong <zyw@...k-chips.com>
To: dianders@...omium.org, tfiga@...omium.org, heiko@...ech.de,
yzq@...k-chips.com, groeck@...omium.org, myungjoo.ham@...sung.com,
cw00.choi@...sung.com, wulf@...k-chips.com, marcheu@...omium.org,
briannorris@...omium.org
Cc: linux-rockchip@...ts.infradead.org,
Chris Zhong <zyw@...k-chips.com>, devicetree@...r.kernel.org,
Guenter Roeck <linux@...ck-us.net>,
Kever Yang <kever.yang@...k-chips.com>,
Kumar Gala <galak@...eaurora.org>,
linux-kernel@...r.kernel.org,
Ian Campbell <ijc+devicetree@...lion.org.uk>,
Rob Herring <robh+dt@...nel.org>,
Pawel Moll <pawel.moll@....com>,
Mark Rutland <mark.rutland@....com>,
linux-arm-kernel@...ts.infradead.org
Subject: [v14 PATCH 1/5] Documentation: bindings: add dt doc for Rockchip USB Type-C PHY
This patch adds a binding that describes the Rockchip USB Type-C PHY
for rk3399
Signed-off-by: Chris Zhong <zyw@...k-chips.com>
Reviewed-by: Tomasz Figa <tfiga@...omium.org>
Reviewed-by: Kever Yang <kever.yang@...k-chips.com>
Reviewed-by: Guenter Roeck <linux@...ck-us.net>
Acked-by: Rob Herring <robh@...nel.org>
---
Changes in v14: None
Changes in v13: None
Changes in v12: None
Changes in v11:
- make a clearer emarcation between usb phy and dp phy
Changes in v10:
- remove rockchip,uphy-dp-sel property
Changes in v9:
- change #phy-cells to 1
Changes in v8: None
Changes in v7: None
Changes in v6:
- add assigned-clocks and assigned-clock-rates
Changes in v5: None
Changes in v4:
- add a #phy-cells node
Changes in v3:
- use compatible: rockchip,rk3399-typec-phy
- use dashes instead of underscores.
Changes in v2:
- add some registers description
Changes in v1:
- add extcon node description
- move the registers in phy driver
- remove the suffix of reset
.../devicetree/bindings/phy/phy-rockchip-typec.txt | 101 +++++++++++++++++++++
1 file changed, 101 insertions(+)
create mode 100644 Documentation/devicetree/bindings/phy/phy-rockchip-typec.txt
diff --git a/Documentation/devicetree/bindings/phy/phy-rockchip-typec.txt b/Documentation/devicetree/bindings/phy/phy-rockchip-typec.txt
new file mode 100644
index 0000000..6ea867e
--- /dev/null
+++ b/Documentation/devicetree/bindings/phy/phy-rockchip-typec.txt
@@ -0,0 +1,101 @@
+* ROCKCHIP type-c PHY
+---------------------
+
+Required properties:
+ - compatible : must be "rockchip,rk3399-typec-phy"
+ - reg: Address and length of the usb phy control register set
+ - rockchip,grf : phandle to the syscon managing the "general
+ register files"
+ - clocks : phandle + clock specifier for the phy clocks
+ - clock-names : string, clock name, must be "tcpdcore", "tcpdphy-ref";
+ - assigned-clocks: main clock, should be <&cru SCLK_UPHY0_TCPDCORE> or
+ <&cru SCLK_UPHY1_TCPDCORE>;
+ - assigned-clock-rates : the phy core clk frequency, shall be: 50000000
+ - resets : a list of phandle + reset specifier pairs
+ - reset-names : string reset name, must be:
+ "uphy", "uphy-pipe", "uphy-tcphy"
+ - extcon : extcon specifier for the Power Delivery
+
+Note, there are 2 type-c phys for RK3399, and they are almost identical, except
+these registers(description below), every register node contains 3 sections:
+offset, enable bit, write mask bit.
+ - rockchip,typec-conn-dir : the register of type-c connector direction,
+ for type-c phy0, it must be <0xe580 0 16>;
+ for type-c phy1, it must be <0xe58c 0 16>;
+ - rockchip,usb3tousb2-en : the register of type-c force usb3 to usb2 enable
+ control.
+ for type-c phy0, it must be <0xe580 3 19>;
+ for type-c phy1, it must be <0xe58c 3 19>;
+ - rockchip,external-psm : the register of type-c phy external psm clock
+ selection.
+ for type-c phy0, it must be <0xe588 14 30>;
+ for type-c phy1, it must be <0xe594 14 30>;
+ - rockchip,pipe-status : the register of type-c phy pipe status.
+ for type-c phy0, it must be <0xe5c0 0 0>;
+ for type-c phy1, it must be <0xe5c0 16 16>;
+
+Required nodes : a sub-node is required for each port the phy provides.
+ The sub-node name is used to identify dp or usb3 port,
+ and shall be the following entries:
+ * "dp-port" : the name of DP port.
+ * "usb3-port" : the name of USB3 port.
+
+Required properties (port (child) node):
+- #phy-cells : must be 0, See ./phy-bindings.txt for details.
+
+Example:
+ tcphy0: phy@...c0000 {
+ compatible = "rockchip,rk3399-typec-phy";
+ reg = <0x0 0xff7c0000 0x0 0x40000>;
+ rockchip,grf = <&grf>;
+ extcon = <&fusb0>;
+ clocks = <&cru SCLK_UPHY0_TCPDCORE>,
+ <&cru SCLK_UPHY0_TCPDPHY_REF>;
+ clock-names = "tcpdcore", "tcpdphy-ref";
+ assigned-clocks = <&cru SCLK_UPHY0_TCPDCORE>;
+ assigned-clock-rates = <50000000>;
+ resets = <&cru SRST_UPHY0>,
+ <&cru SRST_UPHY0_PIPE_L00>,
+ <&cru SRST_P_UPHY0_TCPHY>;
+ reset-names = "uphy", "uphy-pipe", "uphy-tcphy";
+ rockchip,typec-conn-dir = <0xe580 0 16>;
+ rockchip,usb3tousb2-en = <0xe580 3 19>;
+ rockchip,external-psm = <0xe588 14 30>;
+ rockchip,pipe-status = <0xe5c0 0 0>;
+
+ tcphy0_dp: dp-port {
+ #phy-cells = <0>;
+ };
+
+ tcphy0_usb3: usb3-port {
+ #phy-cells = <0>;
+ };
+ };
+
+ tcphy1: phy@...00000 {
+ compatible = "rockchip,rk3399-typec-phy";
+ reg = <0x0 0xff800000 0x0 0x40000>;
+ rockchip,grf = <&grf>;
+ extcon = <&fusb1>;
+ clocks = <&cru SCLK_UPHY1_TCPDCORE>,
+ <&cru SCLK_UPHY1_TCPDPHY_REF>;
+ clock-names = "tcpdcore", "tcpdphy-ref";
+ assigned-clocks = <&cru SCLK_UPHY1_TCPDCORE>;
+ assigned-clock-rates = <50000000>;
+ resets = <&cru SRST_UPHY1>,
+ <&cru SRST_UPHY1_PIPE_L00>,
+ <&cru SRST_P_UPHY1_TCPHY>;
+ reset-names = "uphy", "uphy-pipe", "uphy-tcphy";
+ rockchip,typec-conn-dir = <0xe58c 0 16>;
+ rockchip,usb3tousb2-en = <0xe58c 3 19>;
+ rockchip,external-psm = <0xe594 14 30>;
+ rockchip,pipe-status = <0xe5c0 16 16>;
+
+ tcphy1_dp: dp-port {
+ #phy-cells = <0>;
+ };
+
+ tcphy1_usb3: usb3-port {
+ #phy-cells = <0>;
+ };
+ };
--
1.9.1
Powered by blists - more mailing lists