Message-ID: <20160902090600.27262-3-nm@ti.com>
Date:   Fri, 2 Sep 2016 04:06:00 -0500
From:   Nishanth Menon <nm@...com>
To:     Tony Lindgren <tony@...mide.com>
CC:     Tomi Valkeinen <tomi.valkeinen@...com>,
        Kishon Vijay Abraham I <kishon@...com>,
        <linux-omap@...r.kernel.org>, <linux-kernel@...r.kernel.org>,
        <linux-arm-kernel@...ts.infradead.org>,
        <devicetree@...r.kernel.org>, Nishanth Menon <nm@...com>
Subject: [PATCH 2/2] ARM: dts: am57xx-beagle-x15: Add support for rev B1

Latest update to the BeagleBoard-X15 platform (revision B1)[1] updates
for allowing UHS SD cards to function with the split of supply to SD
card from a dedicated LDO.

As a result of this, AM57xx BeagleBoard-X15 now uses gpio2_30 instead
of gpio6_28 for HDMI because HDMI_LS_OE should now be switched from
GPIO6_28(Y9) to GPIO2_30 (AG8) to avoid a 1.8V GPIO toggling a 3.3V
SoC input when the SD card is in UHS 1.8V mode.

NOTE: For UHS mode to function, we need full fledged IODelay support
in kernel to be functional. IODelay support is yet to be added.

Further, It does not make much sense to spin off a new board
compatible flag since there is no real functional benefit for the
same.

Note: Even though production version is supposed to be B1, there is
over ~200 boards of previous version (A2)[2] out there which continue
to get supported with the existing dts file and the production board
is now supported as revb1

[1] https://github.com/beagleboard/beagleboard-x15/blob/master/BEAGLEBOARD_X15_REV_B1.pdf
[2] http://marc.info/?l=linux-arm-kernel&m=147273929820708&w=2

Signed-off-by: Nishanth Menon <nm@...com>
---

NOTE: even though I have used -C -M option with git-format-patch, the
diff for x15.dts might look a little weird. we could alternatively
split the patch into two by creating a common dtsi and then
introducing revb1 -> but, at least for the moment, I felt it to be an
overkill.

Also, please note that even though revb1 is the production platform,
there are sufficient quantities of x15 A2s (pre-prod) in the wild
currently to leave existing dts in sync with A2 and introduce b1 as a
seperate dts (instead of the other way around).

 arch/arm/boot/dts/Makefile                         |   1 +
 ...eagle-x15.dts => am57xx-beagle-x15-common.dtsi} |   8 +-
 arch/arm/boot/dts/am57xx-beagle-x15-revb1.dts      |  24 +
 arch/arm/boot/dts/am57xx-beagle-x15.dts            | 592 +--------------------
 4 files changed, 33 insertions(+), 592 deletions(-)
 copy arch/arm/boot/dts/{am57xx-beagle-x15.dts => am57xx-beagle-x15-common.dtsi} (97%)
 create mode 100644 arch/arm/boot/dts/am57xx-beagle-x15-revb1.dts

diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index faacd52370d2..b8d9840895c2 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -570,6 +570,7 @@ dtb-$(CONFIG_SOC_OMAP5) += \
 	omap5-uevm.dtb
 dtb-$(CONFIG_SOC_DRA7XX) += \
 	am57xx-beagle-x15.dtb \
+	am57xx-beagle-x15-revb1.dtb \
 	am57xx-cl-som-am57x.dtb \
 	am57xx-sbc-am57x.dtb \
 	am572x-idk.dtb \
diff --git a/arch/arm/boot/dts/am57xx-beagle-x15.dts b/arch/arm/boot/dts/am57xx-beagle-x15-common.dtsi
similarity index 97%
copy from arch/arm/boot/dts/am57xx-beagle-x15.dts
copy to arch/arm/boot/dts/am57xx-beagle-x15-common.dtsi
index ef21da558ea3..ec85ff9004e8 100644
--- a/arch/arm/boot/dts/am57xx-beagle-x15.dts
+++ b/arch/arm/boot/dts/am57xx-beagle-x15-common.dtsi
@@ -1,5 +1,5 @@
 /*
- * Copyright (C) 2014 Texas Instruments Incorporated - http://www.ti.com/
+ * Copyright (C) 2014-2016 Texas Instruments Incorporated - http://www.ti.com/
  *
  * This program is free software; you can redistribute it and/or modify
  * it under the terms of the GNU General Public License version 2 as
@@ -13,7 +13,6 @@
 #include <dt-bindings/interrupt-controller/irq.h>
 
 / {
-	model = "TI AM5728 BeagleBoard-X15";
 	compatible = "ti,am572x-beagle-x15", "ti,am5728", "ti,dra742", "ti,dra74", "ti,dra7";
 
 	aliases {
@@ -114,10 +113,6 @@
 	tpd12s015: encoder {
 		compatible = "ti,tpd12s015";
 
-		gpios = <&gpio7 10 GPIO_ACTIVE_HIGH>,	/* gpio7_10, CT CP HPD */
-			<&gpio6 28 GPIO_ACTIVE_HIGH>,	/* gpio6_28, LS OE */
-			<&gpio7 12 GPIO_ACTIVE_HIGH>;	/* gpio7_12/sp1_cs2, HPD */
-
 		ports {
 			#address-cells = <1>;
 			#size-cells = <0>;
@@ -448,7 +443,6 @@
 	pinctrl-names = "default";
 	pinctrl-0 = <&mmc1_pins_default>;
 
-	vmmc-supply = <&ldo1_reg>;
 	bus-width = <4>;
 	cd-gpios = <&gpio6 27 GPIO_ACTIVE_LOW>; /* gpio 219 */
 };
diff --git a/arch/arm/boot/dts/am57xx-beagle-x15-revb1.dts b/arch/arm/boot/dts/am57xx-beagle-x15-revb1.dts
new file mode 100644
index 000000000000..da61dbba7768
--- /dev/null
+++ b/arch/arm/boot/dts/am57xx-beagle-x15-revb1.dts
@@ -0,0 +1,24 @@
+/*
+ * Copyright (C) 2014-2016 Texas Instruments Incorporated - http://www.ti.com/
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include "am57xx-beagle-x15-common.dtsi"
+
+/ {
+	model = "TI AM5728 BeagleBoard-X15 rev B1";
+};
+
+&tpd12s015 {
+	gpios = <&gpio7 10 GPIO_ACTIVE_HIGH>,	/* gpio7_10, CT CP HPD */
+		<&gpio2 30 GPIO_ACTIVE_HIGH>,	/* gpio6_30, LS OE */
+		<&gpio7 12 GPIO_ACTIVE_HIGH>;	/* gpio7_12/sp1_cs2, HPD */
+};
+
+&mmc1 {
+	vmmc-supply = <&vdd_3v3>;
+	vmmc-aux-supply = <&ldo1_reg>;
+};
diff --git a/arch/arm/boot/dts/am57xx-beagle-x15.dts b/arch/arm/boot/dts/am57xx-beagle-x15.dts
index ef21da558ea3..b47ac4bbfde6 100644
--- a/arch/arm/boot/dts/am57xx-beagle-x15.dts
+++ b/arch/arm/boot/dts/am57xx-beagle-x15.dts
@@ -1,602 +1,24 @@
 /*
- * Copyright (C) 2014 Texas Instruments Incorporated - http://www.ti.com/
+ * Copyright (C) 2014-2016 Texas Instruments Incorporated - http://www.ti.com/
  *
  * This program is free software; you can redistribute it and/or modify
  * it under the terms of the GNU General Public License version 2 as
  * published by the Free Software Foundation.
  */
-/dts-v1/;
 
-#include "dra74x.dtsi"
-#include "am57xx-commercial-grade.dtsi"
-#include <dt-bindings/gpio/gpio.h>
-#include <dt-bindings/interrupt-controller/irq.h>
+#include "am57xx-beagle-x15-common.dtsi"
 
 / {
 	model = "TI AM5728 BeagleBoard-X15";
-	compatible = "ti,am572x-beagle-x15", "ti,am5728", "ti,dra742", "ti,dra74", "ti,dra7";
-
-	aliases {
-		rtc0 = &mcp_rtc;
-		rtc1 = &tps659038_rtc;
-		rtc2 = &rtc;
-		display0 = &hdmi0;
-	};
-
-	memory@0 {
-		device_type = "memory";
-		reg = <0x0 0x80000000 0x0 0x80000000>;
-	};
-
-	vdd_3v3: fixedregulator-vdd_3v3 {
-		compatible = "regulator-fixed";
-		regulator-name = "vdd_3v3";
-		vin-supply = <&regen1>;
-		regulator-min-microvolt = <3300000>;
-		regulator-max-microvolt = <3300000>;
-	};
-
-	aic_dvdd: fixedregulator-aic_dvdd {
-		compatible = "regulator-fixed";
-		regulator-name = "aic_dvdd_fixed";
-		vin-supply = <&vdd_3v3>;
-		regulator-min-microvolt = <1800000>;
-		regulator-max-microvolt = <1800000>;
-	};
-
-	vtt_fixed: fixedregulator-vtt {
-		/* TPS51200 */
-		compatible = "regulator-fixed";
-		regulator-name = "vtt_fixed";
-		vin-supply = <&smps3_reg>;
-		regulator-min-microvolt = <3300000>;
-		regulator-max-microvolt = <3300000>;
-		regulator-always-on;
-		regulator-boot-on;
-		enable-active-high;
-		gpio = <&gpio7 11 GPIO_ACTIVE_HIGH>;
-	};
-
-	leds {
-		compatible = "gpio-leds";
-
-		led0 {
-			label = "beagle-x15:usr0";
-			gpios = <&gpio7 9 GPIO_ACTIVE_HIGH>;
-			linux,default-trigger = "heartbeat";
-			default-state = "off";
-		};
-
-		led1 {
-			label = "beagle-x15:usr1";
-			gpios = <&gpio7 8 GPIO_ACTIVE_HIGH>;
-			linux,default-trigger = "cpu0";
-			default-state = "off";
-		};
-
-		led2 {
-			label = "beagle-x15:usr2";
-			gpios = <&gpio7 14 GPIO_ACTIVE_HIGH>;
-			linux,default-trigger = "mmc0";
-			default-state = "off";
-		};
-
-		led3 {
-			label = "beagle-x15:usr3";
-			gpios = <&gpio7 15 GPIO_ACTIVE_HIGH>;
-			linux,default-trigger = "disk-activity";
-			default-state = "off";
-		};
-	};
-
-	gpio_fan: gpio_fan {
-		/* Based on 5v 500mA AFB02505HHB */
-		compatible = "gpio-fan";
-		gpios =  <&tps659038_gpio 2 GPIO_ACTIVE_HIGH>;
-		gpio-fan,speed-map = <0     0>,
-				     <13000 1>;
-		#cooling-cells = <2>;
-	};
-
-	hdmi0: connector {
-		compatible = "hdmi-connector";
-		label = "hdmi";
-
-		type = "a";
-
-		port {
-			hdmi_connector_in: endpoint {
-				remote-endpoint = <&tpd12s015_out>;
-			};
-		};
-	};
-
-	tpd12s015: encoder {
-		compatible = "ti,tpd12s015";
-
-		gpios = <&gpio7 10 GPIO_ACTIVE_HIGH>,	/* gpio7_10, CT CP HPD */
-			<&gpio6 28 GPIO_ACTIVE_HIGH>,	/* gpio6_28, LS OE */
-			<&gpio7 12 GPIO_ACTIVE_HIGH>;	/* gpio7_12/sp1_cs2, HPD */
-
-		ports {
-			#address-cells = <1>;
-			#size-cells = <0>;
-
-			port@0 {
-				reg = <0>;
-
-				tpd12s015_in: endpoint {
-					remote-endpoint = <&hdmi_out>;
-				};
-			};
-
-			port@1 {
-				reg = <1>;
-
-				tpd12s015_out: endpoint {
-					remote-endpoint = <&hdmi_connector_in>;
-				};
-			};
-		};
-	};
-
-	sound0: sound0 {
-		compatible = "simple-audio-card";
-		simple-audio-card,name = "BeagleBoard-X15";
-		simple-audio-card,widgets =
-			"Line", "Line Out",
-			"Line", "Line In";
-		simple-audio-card,routing =
-			"Line Out",	"LLOUT",
-			"Line Out",	"RLOUT",
-			"MIC2L",	"Line In",
-			"MIC2R",	"Line In";
-		simple-audio-card,format = "dsp_b";
-		simple-audio-card,bitclock-master = <&sound0_master>;
-		simple-audio-card,frame-master = <&sound0_master>;
-		simple-audio-card,bitclock-inversion;
-
-		simple-audio-card,cpu {
-			sound-dai = <&mcasp3>;
-		};
-
-		sound0_master: simple-audio-card,codec {
-			sound-dai = <&tlv320aic3104>;
-			clocks = <&clkout2_clk>;
-		};
-	};
-};
-
-&dra7_pmx_core {
-	mmc1_pins_default: mmc1_pins_default {
-		pinctrl-single,pins = <
-			DRA7XX_CORE_IOPAD(0x376c, PIN_INPUT | MUX_MODE14)	/* mmc1sdcd.gpio219 */
-			DRA7XX_CORE_IOPAD(0x3754, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_clk.clk */
-			DRA7XX_CORE_IOPAD(0x3758, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_cmd.cmd */
-			DRA7XX_CORE_IOPAD(0x375c, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_dat0.dat0 */
-			DRA7XX_CORE_IOPAD(0x3760, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_dat1.dat1 */
-			DRA7XX_CORE_IOPAD(0x3764, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_dat2.dat2 */
-			DRA7XX_CORE_IOPAD(0x3768, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_dat3.dat3 */
-		>;
-	};
-
-	mmc2_pins_default: mmc2_pins_default {
-		pinctrl-single,pins = <
-			DRA7XX_CORE_IOPAD(0x349c, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a23.mmc2_clk */
-			DRA7XX_CORE_IOPAD(0x34b0, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_cs1.mmc2_cmd */
-			DRA7XX_CORE_IOPAD(0x34a0, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a24.mmc2_dat0 */
-			DRA7XX_CORE_IOPAD(0x34a4, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a25.mmc2_dat1 */
-			DRA7XX_CORE_IOPAD(0x34a8, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a26.mmc2_dat2 */
-			DRA7XX_CORE_IOPAD(0x34ac, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a27.mmc2_dat3 */
-			DRA7XX_CORE_IOPAD(0x348c, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a19.mmc2_dat4 */
-			DRA7XX_CORE_IOPAD(0x3490, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a20.mmc2_dat5 */
-			DRA7XX_CORE_IOPAD(0x3494, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a21.mmc2_dat6 */
-			DRA7XX_CORE_IOPAD(0x3498, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a22.mmc2_dat7 */
-		>;
-	};
-};
-&i2c1 {
-	status = "okay";
-	clock-frequency = <400000>;
-
-	tps659038: tps659038@58 {
-		compatible = "ti,tps659038";
-		reg = <0x58>;
-		interrupt-parent = <&gpio1>;
-		interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
-
-		#interrupt-cells = <2>;
-		interrupt-controller;
-
-		ti,system-power-controller;
-
-		tps659038_pmic {
-			compatible = "ti,tps659038-pmic";
-
-			regulators {
-				smps12_reg: smps12 {
-					/* VDD_MPU */
-					regulator-name = "smps12";
-					regulator-min-microvolt = < 850000>;
-					regulator-max-microvolt = <1250000>;
-					regulator-always-on;
-					regulator-boot-on;
-				};
-
-				smps3_reg: smps3 {
-					/* VDD_DDR */
-					regulator-name = "smps3";
-					regulator-min-microvolt = <1350000>;
-					regulator-max-microvolt = <1350000>;
-					regulator-always-on;
-					regulator-boot-on;
-				};
-
-				smps45_reg: smps45 {
-					/* VDD_DSPEVE, VDD_IVA, VDD_GPU */
-					regulator-name = "smps45";
-					regulator-min-microvolt = < 850000>;
-					regulator-max-microvolt = <1250000>;
-					regulator-always-on;
-					regulator-boot-on;
-				};
-
-				smps6_reg: smps6 {
-					/* VDD_CORE */
-					regulator-name = "smps6";
-					regulator-min-microvolt = <850000>;
-					regulator-max-microvolt = <1150000>;
-					regulator-always-on;
-					regulator-boot-on;
-				};
-
-				/* SMPS7 unused */
-
-				smps8_reg: smps8 {
-					/* VDD_1V8 */
-					regulator-name = "smps8";
-					regulator-min-microvolt = <1800000>;
-					regulator-max-microvolt = <1800000>;
-					regulator-always-on;
-					regulator-boot-on;
-				};
-
-				/* SMPS9 unused */
-
-				ldo1_reg: ldo1 {
-					/* VDD_SD / VDDSHV8  */
-					regulator-name = "ldo1";
-					regulator-min-microvolt = <1800000>;
-					regulator-max-microvolt = <3300000>;
-					regulator-boot-on;
-					regulator-always-on;
-				};
-
-				ldo2_reg: ldo2 {
-					/* VDD_SHV5 */
-					regulator-name = "ldo2";
-					regulator-min-microvolt = <3300000>;
-					regulator-max-microvolt = <3300000>;
-					regulator-always-on;
-					regulator-boot-on;
-				};
-
-				ldo3_reg: ldo3 {
-					/* VDDA_1V8_PHYA */
-					regulator-name = "ldo3";
-					regulator-min-microvolt = <1800000>;
-					regulator-max-microvolt = <1800000>;
-					regulator-always-on;
-					regulator-boot-on;
-				};
-
-				ldo4_reg: ldo4 {
-					/* VDDA_1V8_PHYB */
-					regulator-name = "ldo4";
-					regulator-min-microvolt = <1800000>;
-					regulator-max-microvolt = <1800000>;
-					regulator-always-on;
-					regulator-boot-on;
-				};
-
-				ldo9_reg: ldo9 {
-					/* VDD_RTC */
-					regulator-name = "ldo9";
-					regulator-min-microvolt = <1050000>;
-					regulator-max-microvolt = <1050000>;
-					regulator-always-on;
-					regulator-boot-on;
-				};
-
-				ldoln_reg: ldoln {
-					/* VDDA_1V8_PLL */
-					regulator-name = "ldoln";
-					regulator-min-microvolt = <1800000>;
-					regulator-max-microvolt = <1800000>;
-					regulator-always-on;
-					regulator-boot-on;
-				};
-
-				ldousb_reg: ldousb {
-					/* VDDA_3V_USB: VDDA_USBHS33 */
-					regulator-name = "ldousb";
-					regulator-min-microvolt = <3300000>;
-					regulator-max-microvolt = <3300000>;
-					regulator-boot-on;
-				};
-
-				regen1: regen1 {
-					/* VDD_3V3_ON */
-					regulator-name = "regen1";
-					regulator-boot-on;
-					regulator-always-on;
-				};
-			};
-		};
-
-		tps659038_rtc: tps659038_rtc {
-			compatible = "ti,palmas-rtc";
-			interrupt-parent = <&tps659038>;
-			interrupts = <8 IRQ_TYPE_EDGE_FALLING>;
-			wakeup-source;
-		};
-
-		tps659038_pwr_button: tps659038_pwr_button {
-			compatible = "ti,palmas-pwrbutton";
-			interrupt-parent = <&tps659038>;
-			interrupts = <1 IRQ_TYPE_EDGE_FALLING>;
-			wakeup-source;
-			ti,palmas-long-press-seconds = <12>;
-		};
-
-		tps659038_gpio: tps659038_gpio {
-			compatible = "ti,palmas-gpio";
-			gpio-controller;
-			#gpio-cells = <2>;
-		};
-
-		extcon_usb2: tps659038_usb {
-			compatible = "ti,palmas-usb-vid";
-			ti,enable-vbus-detection;
-			vbus-gpio = <&gpio4 21 GPIO_ACTIVE_HIGH>;
-		};
-
-	};
-
-	tmp102: tmp102@48 {
-		compatible = "ti,tmp102";
-		reg = <0x48>;
-		interrupt-parent = <&gpio7>;
-		interrupts = <16 IRQ_TYPE_LEVEL_LOW>;
-		#thermal-sensor-cells = <1>;
-	};
-
-	tlv320aic3104: tlv320aic3104@18 {
-		#sound-dai-cells = <0>;
-		compatible = "ti,tlv320aic3104";
-		reg = <0x18>;
-		assigned-clocks = <&clkoutmux2_clk_mux>;
-		assigned-clock-parents = <&sys_clk2_dclk_div>;
-
-		status = "okay";
-		adc-settle-ms = <40>;
-
-		AVDD-supply = <&vdd_3v3>;
-		IOVDD-supply = <&vdd_3v3>;
-		DRVDD-supply = <&vdd_3v3>;
-		DVDD-supply = <&aic_dvdd>;
-	};
-
-	eeprom: eeprom@50 {
-		compatible = "at,24c32";
-		reg = <0x50>;
-	};
 };
 
-&i2c3 {
-	status = "okay";
-	clock-frequency = <400000>;
-
-	mcp_rtc: rtc@6f {
-		compatible = "microchip,mcp7941x";
-		reg = <0x6f>;
-		interrupts-extended = <&crossbar_mpu GIC_SPI 2 IRQ_TYPE_EDGE_RISING>,
-				      <&dra7_pmx_core 0x424>;
-		interrupt-names = "irq", "wakeup";
-
-		vcc-supply = <&vdd_3v3>;
-		wakeup-source;
-	};
-};
-
-&gpio7 {
-	ti,no-reset-on-init;
-	ti,no-idle-on-init;
-};
-
-&cpu0 {
-	cpu0-supply = <&smps12_reg>;
-	voltage-tolerance = <1>;
-};
-
-&uart3 {
-	status = "okay";
-	interrupts-extended = <&crossbar_mpu GIC_SPI 69 IRQ_TYPE_LEVEL_HIGH>,
-			      <&dra7_pmx_core 0x3f8>;
-};
-
-&mac {
-	status = "okay";
-	dual_emac;
-};
-
-&cpsw_emac0 {
-	phy_id = <&davinci_mdio>, <1>;
-	phy-mode = "rgmii";
-	dual_emac_res_vlan = <1>;
-};
-
-&cpsw_emac1 {
-	phy_id = <&davinci_mdio>, <2>;
-	phy-mode = "rgmii";
-	dual_emac_res_vlan = <2>;
+&tpd12s015 {
+	gpios = <&gpio7 10 GPIO_ACTIVE_HIGH>,	/* gpio7_10, CT CP HPD */
+		<&gpio6 28 GPIO_ACTIVE_HIGH>,	/* gpio6_28, LS OE */
+		<&gpio7 12 GPIO_ACTIVE_HIGH>;	/* gpio7_12/sp1_cs2, HPD */
 };
 
 &mmc1 {
-	status = "okay";
-
-	pinctrl-names = "default";
-	pinctrl-0 = <&mmc1_pins_default>;
-
-	vmmc-supply = <&ldo1_reg>;
-	bus-width = <4>;
-	cd-gpios = <&gpio6 27 GPIO_ACTIVE_LOW>; /* gpio 219 */
-};
-
-&mmc2 {
-	status = "okay";
-
-	pinctrl-names = "default";
-	pinctrl-0 = <&mmc1_pins_default>;
-
 	vmmc-supply = <&vdd_3v3>;
-	bus-width = <8>;
-	ti,non-removable;
-	cap-mmc-dual-data-rate;
-};
-
-&sata {
-	status = "okay";
-};
-
-&usb2_phy1 {
-	phy-supply = <&ldousb_reg>;
-};
-
-&usb2_phy2 {
-	phy-supply = <&ldousb_reg>;
-};
-
-&usb1 {
-	dr_mode = "host";
-};
-
-&omap_dwc3_2 {
-	extcon = <&extcon_usb2>;
-};
-
-&usb2 {
-	/*
-	 * Stand alone usage is peripheral only.
-	 * However, with some resistor modifications
-	 * this port can be used via expansion connectors
-	 * as "host" or "dual-role". If so, provide
-	 * the necessary dr_mode override in the expansion
-	 * board's DT.
-	 */
-	dr_mode = "peripheral";
-};
-
-&cpu_trips {
-	cpu_alert1: cpu_alert1 {
-		temperature = <50000>; /* millicelsius */
-		hysteresis = <2000>; /* millicelsius */
-		type = "active";
-	};
-};
-
-&cpu_cooling_maps {
-	map1 {
-		trip = <&cpu_alert1>;
-		cooling-device = <&gpio_fan THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
-	};
-};
-
-&thermal_zones {
-	board_thermal: board_thermal {
-		polling-delay-passive = <1250>; /* milliseconds */
-		polling-delay = <1500>; /* milliseconds */
-
-				/* sensor       ID */
-		thermal-sensors = <&tmp102     0>;
-
-		board_trips: trips {
-			board_alert0: board_alert {
-				temperature = <40000>; /* millicelsius */
-				hysteresis = <2000>; /* millicelsius */
-				type = "active";
-			};
-
-			board_crit: board_crit {
-				temperature = <105000>; /* millicelsius */
-				hysteresis = <0>; /* millicelsius */
-				type = "critical";
-			};
-		};
-
-		board_cooling_maps: cooling-maps {
-			map0 {
-				trip = <&board_alert0>;
-				cooling-device =
-				  <&gpio_fan THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
-			};
-		};
-       };
-};
-
-&dss {
-	status = "ok";
-
-	vdda_video-supply = <&ldoln_reg>;
-};
-
-&hdmi {
-	status = "ok";
-	vdda-supply = <&ldo4_reg>;
-
-	port {
-		hdmi_out: endpoint {
-			remote-endpoint = <&tpd12s015_in>;
-		};
-	};
-};
-
-&pcie1 {
-	gpios = <&gpio2 8 GPIO_ACTIVE_LOW>;
-};
-
-&mcasp3 {
-	#sound-dai-cells = <0>;
-	assigned-clocks = <&mcasp3_ahclkx_mux>;
-	assigned-clock-parents = <&sys_clkin2>;
-	status = "okay";
-
-	op-mode = <0>;	/* MCASP_IIS_MODE */
-	tdm-slots = <2>;
-	/* 4 serializers */
-	serial-dir = <	/* 0: INACTIVE, 1: TX, 2: RX */
-		1 2 0 0
-	>;
-	tx-num-evt = <32>;
-	rx-num-evt = <32>;
-};
-
-&mailbox5 {
-	status = "okay";
-	mbox_ipu1_ipc3x: mbox_ipu1_ipc3x {
-		status = "okay";
-	};
-	mbox_dsp1_ipc3x: mbox_dsp1_ipc3x {
-		status = "okay";
-	};
-};
-
-&mailbox6 {
-	status = "okay";
-	mbox_ipu2_ipc3x: mbox_ipu2_ipc3x {
-		status = "okay";
-	};
-	mbox_dsp2_ipc3x: mbox_dsp2_ipc3x {
-		status = "okay";
-	};
+	vmmc-aux-supply = <&ldo1_reg>;
 };
-- 
2.9.1.200.gb1ec08f

Powered by blists - more mailing lists