linux-kernel - [PATCH v5 6/6] ARM: dts: imx6qdl-icore: Add FEC support

lists.openwall.net		lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC
Open Source and information security mailing list archives

Hash Suite: Windows password security audit tool. GUI, reports in PDF.

[<prev] [next>] [<thread-prev] [thread-next>] [day] [month] [year] [list]

Message-Id: <1473967015-8523-7-git-send-email-jagan@amarulasolutions.com>
Date:   Fri, 16 Sep 2016 00:46:55 +0530
From:   Jagan Teki <jagannadh.teki@...il.com>
To:     linux-arm-kernel@...ts.infradead.org
Cc:     devicetree@...r.kernel.org, linux-kernel@...r.kernel.org,
        Sascha Hauer <kernel@...gutronix.de>,
        Fabio Estevam <fabio.estevam@....com>,
        Shawn Guo <shawnguo@...nel.org>,
        Matteo Lisi <matteo.lisi@...icam.com>,
        Michael Trimarchi <michael@...rulasolutions.com>,
        Jagan Teki <jagan@...rulasolutions.com>
Subject: [PATCH v5 6/6] ARM: dts: imx6qdl-icore: Add FEC support

Add FEC support for Engicam i.CoreM6 dql modules.

Observed similar 'eth0: link is not ready' issue which was
discussed in [1] due rmii mode with external ref_clk, so added
clock node along with the properties mentioned by Shawn in [2]

FEC link log:
------------
$ ifconfig eth0 up
[   27.905187] SMSC LAN8710/LAN8720 2188000.ethernet:00: attached PHY driver
               [SMSC LAN8710/LAN8720] (mii_bus:phy_addr=2188000.ethernet:00, irq=-1)
[   27.918982] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready

[1] https://patchwork.kernel.org/patch/3491061/
[2] https://patchwork.kernel.org/patch/3490511/

Cc: Sascha Hauer <kernel@...gutronix.de>
Cc: Fabio Estevam <fabio.estevam@....com>
Cc: Shawn Guo <shawnguo@...nel.org>
Cc: Matteo Lisi <matteo.lisi@...icam.com>
Cc: Michael Trimarchi <michael@...rulasolutions.com>
Signed-off-by: Jagan Teki <jagan@...rulasolutions.com>
---
Changes for v5:
	- new patch

 arch/arm/boot/dts/imx6qdl-icore.dtsi | 37 ++++++++++++++++++++++++++++++++++++
 1 file changed, 37 insertions(+)

diff --git a/arch/arm/boot/dts/imx6qdl-icore.dtsi b/arch/arm/boot/dts/imx6qdl-icore.dtsi
index a0ca442..77df730 100644
--- a/arch/arm/boot/dts/imx6qdl-icore.dtsi
+++ b/arch/arm/boot/dts/imx6qdl-icore.dtsi
@@ -48,6 +48,18 @@
 		reg = <0x10000000 0x80000000>;
 	};
 
+	clocks {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		rmii_clk: clock@0 {
+			compatible = "fixed-clock";
+			reg = <0>;
+			#clock-cells = <0>;
+			clock-frequency = <25000000>;  /* 25MHz for example */
+		};
+	};
+
 	reg_3p3v: regulator-3p3v {
 		compatible = "regulator-fixed";
 		regulator-name = "3P3V";
@@ -91,6 +103,15 @@
 	assigned-clock-parents = <&clks IMX6QDL_CLK_OSC>;
 };
 
+&fec {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_enet>;
+	phy-reset-gpios = <&gpio7 12 GPIO_ACTIVE_LOW>;
+	clocks = <&clks 117>, <&clks 117>, <&rmii_clk>;
+	phy-mode = "rmii";
+	status = "okay";
+};
+
 &gpmi {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_gpmi_nand>;
@@ -148,6 +169,22 @@
 };
 
 &iomuxc {
+	pinctrl_enet: enetgrp {
+		fsl,pins = <
+			MX6QDL_PAD_ENET_CRS_DV__ENET_RX_EN	0x1b0b0
+			MX6QDL_PAD_GPIO_16__ENET_REF_CLK	0x1b0b1
+			MX6QDL_PAD_ENET_TX_EN__ENET_TX_EN	0x1b0b0
+			MX6QDL_PAD_ENET_RXD1__ENET_RX_DATA1	0x1b0b0
+			MX6QDL_PAD_ENET_RXD0__ENET_RX_DATA0	0x1b0b0
+			MX6QDL_PAD_ENET_TXD1__ENET_TX_DATA1	0x1b0b0
+			MX6QDL_PAD_ENET_TXD0__ENET_TX_DATA0	0x1b0b0
+			MX6QDL_PAD_ENET_MDC__ENET_MDC		0x1b0b0
+			MX6QDL_PAD_ENET_MDIO__ENET_MDIO		0x1b0b0
+			MX6QDL_PAD_ENET_REF_CLK__GPIO1_IO23	0x1b0b0
+			MX6QDL_PAD_GPIO_17__GPIO7_IO12		0x1b0b0
+		>;
+	};
+
 	pinctrl_flexcan1: flexcan1grp {
 		fsl,pins = <
 			MX6QDL_PAD_KEY_ROW2__FLEXCAN1_RX 0x1b020
-- 
2.7.4