| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-Id: <fc0ca2b3140287cbccf5c176a12b7dce25d06a47.1475853198.git-series.gregory.clement@free-electrons.com>
Date: Fri, 7 Oct 2016 17:22:51 +0200
From: Gregory CLEMENT <gregory.clement@...e-electrons.com>
To: Ulf Hansson <ulf.hansson@...aro.org>,
Adrian Hunter <adrian.hunter@...el.com>,
linux-mmc@...r.kernel.org
Cc: Jason Cooper <jason@...edaemon.net>, Andrew Lunn <andrew@...n.ch>,
Sebastian Hesselbarth <sebastian.hesselbarth@...il.com>,
Gregory CLEMENT <gregory.clement@...e-electrons.com>,
Rob Herring <robh+dt@...nel.org>, devicetree@...r.kernel.org,
Thomas Petazzoni <thomas.petazzoni@...e-electrons.com>,
linux-arm-kernel@...ts.infradead.org, Ziji Hu <huziji@...vell.com>,
"Jack(SH) Zhu" <jmzhu@...vell.com>, Jimmy Xu <zmxu@...vell.com>,
Jisheng Zhang <jszhang@...vell.com>,
Nadav Haklai <nadavh@...vell.com>, Ryan Gao <ygao@...vell.com>,
Doug Jones <dougj@...vell.com>,
Shiwu Zhang <zhangshw@...vell.com>,
Victor Gu <xigu@...vell.com>,
"Wei(SOCP) Liu" <liuw@...vell.com>,
Wilson Ding <dingwei@...vell.com>,
Xueping Liu <xpliu@...vell.com>,
Hilbert Zhang <zzhang@...vell.com>,
Keji Zhang <keji@...vell.com>,
Liuliu Zhao <zhaoliul@...vell.com>,
Peng Zhu <zhupeng@...vell.com>, Yu Cao <yucao@...vell.com>,
Romain Perier <romain.perier@...e-electrons.com>,
Yehuda Yitschak <yehuday@...vell.com>,
Marcin Wojtas <mw@...ihalf.com>,
Hanna Hawa <hannah@...vell.com>,
Kostya Porotchkin <kostap@...vell.com>,
linux-kernel@...r.kernel.org
Subject: [PATCH 5/10] dt: bindings: Add bindings for Marvell Xenon SD Host Controller
From: Ziji Hu <huziji@...vell.com>
Marvell Xenon SDHC can support eMMC/SD/SDIO.
Add Xenon-specific properties.
Also add properties for Xenon PHY setting.
Signed-off-by: Hu Ziji <huziji@...vell.com>
Reviewed-by: Gregory CLEMENT <gregory.clement@...e-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@...e-electrons.com>
---
Documentation/devicetree/bindings/mmc/marvell,sdhci-xenon.txt | 164 +++++++-
MAINTAINERS | 1 +-
2 files changed, 165 insertions(+), 0 deletions(-)
create mode 100644 Documentation/devicetree/bindings/mmc/marvell,sdhci-xenon.txt
diff --git a/Documentation/devicetree/bindings/mmc/marvell,sdhci-xenon.txt b/Documentation/devicetree/bindings/mmc/marvell,sdhci-xenon.txt
new file mode 100644
index 000000000000..8b25ad28ebbd
--- /dev/null
+++ b/Documentation/devicetree/bindings/mmc/marvell,sdhci-xenon.txt
@@ -0,0 +1,164 @@
+Marvell's Xenon SDHCI Controller device tree bindings
+This file documents differences between the core mmc properties
+described by mmc.txt and the properties used by the Xenon implementation.
+
+A single Xenon IP can support multiple slots.
+Each slot acts as an independent SDHC. It owns independent resources, such
+as register sets clock and PHY.
+Each slot should have an independent device tree node.
+
+Required Properties:
+- compatible: should be "marvell,sdhci-xenon" or "marvell,armada-3700-sdhci".
+
+- Input Clock Name
+ Some SOCs require additional clock for AXI bus.
+ The input clock for Xenon IP core should be named as "core".
+ The optional AXI clock should be named as "axi".
+ - clocks = <&core_clk>, <&axi_clock>;
+ - clock-names = "core", "axi";
+
+- Register Set Size
+ Different Xenon SDHC release has different register set size.
+ The specific size should also refer to the SOC implementation.
+
+Optional Properties:
+- Slot Index
+ A single Xenon IP can support multiple slots.
+ During initialization, each slot should set corresponding setting bit in
+ some Xenon-specific registers. The corresponding bit is determined by
+ this property.
+ - xenon,slotno = <slot_index>;
+ If this property is not provided, Xenon IP should contain only one slot
+ and the slot index will be 0x0 by default.
+
+- PHY Type
+ Xenon support mutilple types of PHYs.
+ To select eMMC 5.1 PHY, set:
+ - xenon,phy-type = "emmc 5.1 phy"
+ eMMC 5.1 PHY is the default choice if this property is not provided.
+ To select eMMC 5.0 PHY, set:
+ - xenon,phy-type = "emmc 5.0 phy"
+ To select SDH PHY, set:
+ - xenon,phy-type = "sdh phy"
+ Please note that eMMC PHY is a general PHY for eMMC/SD/SDIO, other than for
+ eMMC only.
+
+- Customized eMMC PHY Parameters
+ Some boards require different values of some specific eMMC PHY parameters.
+ Some SOCs also require specific workaround to set eMMC PHY.
+ These properties enable diverse boards to customize the eMMC PHY.
+ The supported eMMC PHY parameters are listed in below. All those properties
+ are only available for eMMC PHY 5.1 and eMMC PHY 5.0.
+ ZNR
+ valid range = [0:0x1F].
+ ZNR is set as 0xF by default if this property is not provided.
+ - xenon,phy-znr = <value>;
+
+ ZPR
+ valid range = [0:0x1F].
+ ZPR is set as 0xF by default if this property is not provided.
+ - xenon,phy-zpr = <value>;
+
+ Number of successful tuning times
+ Set the number of required consecutive successful sampling points used to
+ identify a valid sampling window, in tuning process.
+ Valid range = [1:7]. Set as 0x4 by default if this property is not provided.
+ - xenon,phy-nr-tun-times = <nr_times>;
+
+ Divider for TUN_STEP
+ Set the divider for calculating TUN_STEP.
+ Set as 64 by default if this property is not provided.
+ - xenon,phy-tun-step-divider = <divider>;
+
+ Force PHY into slow mode.
+ Only available when bus frequency lower than 50MHz in SDR mde.
+ Disabled by default. Please do not enable it unless it is necessary.
+ - xenon,phy-slow-mode;
+
+- Mask Conflict Error Report
+ Disable Conflict Error alert on some SOC. Disabled by default.
+ xenon,mask-conflict-err;
+
+- Re-tuning Counter
+ Xenon SDHC SOC usually doesn't provide re-tuning counter in
+ Capabilities Register 3 Bit[11:8].
+ This property provides the re-tuning counter.
+ xenon,tuning-count = <count>;
+ If this property is not set, default re-tuning counter will
+ be set as 0x9 in driver.
+
+- SOC PHY PAD Voltage Control register
+ Some SOCs have SOC PHY PAD Voltage Control register outside Xenon IP.
+ This register sets SOC PHY PAD Voltage to keep aligh with Vccq.
+ Two properties provide information of this control register.
+ These two properties are only valid when "marvell,armada-3700-sdhci"
+ is selected. Both of them must be provided when "marvell,armada-3700-sdhci"
+ is selected.
+ - xenon,pad-type
+ Two types: "sd" and "fixed-1-8v".
+ If "sd" is slected, SOC PHY PAD is set as 3.3V at the beginning and is
+ switched to 1.8V when SD in UHS-I.
+ If "fixed-1-8v" is slected, SOC PHY PAD is fixed 1.8V, such as for eMMC.
+ - reg
+ Physical address and size of SOC PHY PAD register.
+ Append after Xenon SDHC register space, as a second register field.
+
+ Please follow the examples with compatible "marvell,armada-3700-sdhci"
+ in below.
+
+Example:
+- For eMMC slot:
+
+ sdhci@...000 {
+ compatible = "marvell,sdhci-xenon";
+ reg = <0xaa0000 0x1000>;
+ interrupts = <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>
+ clocks = <&emmcclk>;
+ clock-names = "core";
+ xenon,slotno = <0>;
+ xenon,phy-type = "emmc 5.1 phy";
+ bus-width = <8>;
+ tuning-count = <11>;
+ };
+
+- For SD/SDIO slot:
+
+ sdhci@...000 {
+ compatible = "marvell,sdhci-xenon";
+ reg = <0xab0000 0x1000>;
+ interrupts = <GIC_SPI 55 IRQ_TYPE_LEVEL_HIGH>
+ vqmmc-supply = <&sd_regulator>;
+ clocks = <&sdclk>;
+ clock-names = "core";
+ bus-width = <4>;
+ tuning-count = <9>;
+ };
+
+- For eMMC slot with compatible "marvell,armada-3700-sdhci":
+
+ sdhci@...000 {
+ compatible = "marvell,armada-3700-sdhci";
+ reg = <0xaa0000 0x1000>,
+ <phy_addr 0x4>;
+ interrupts = <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>
+ clocks = <&emmcclk>;
+ clock-names = "core";
+ bus-width = <8>;
+
+ xenon,pad-type = "fixed-1-8v";
+ };
+
+- For SD/SDIO slot with compatible "marvell,armada-3700-sdhci":
+
+ sdhci@...000 {
+ compatible = "marvell,armada-3700-sdhci";
+ reg = <0xab0000 0x1000>,
+ <phy_addr 0x4>;
+ interrupts = <GIC_SPI 55 IRQ_TYPE_LEVEL_HIGH>
+ vqmmc-supply = <&sd_regulator>;
+ clocks = <&sdclk>;
+ clock-names = "core";
+ bus-width = <4>;
+
+ xenon,pad-type = "sd";
+ };
diff --git a/MAINTAINERS b/MAINTAINERS
index 89adcd57aa25..4aa0eac9bfc7 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -7582,6 +7582,7 @@ MARVELL XENON MMC/SD/SDIO HOST CONTROLLER DRIVER
M: Ziji Hu <huziji@...vell.com>
L: linux-mmc@...r.kernel.org
S: Supported
+F: Documentation/devicetree/bindings/mmc/marvell,sdhci-xenon.txt
MATROX FRAMEBUFFER DRIVER
L: linux-fbdev@...r.kernel.org
--
git-series 0.8.10
Powered by blists - more mailing lists