[<prev] [next>] [<thread-prev] [thread-next>] [day] [month] [year] [list]
Message-Id: <1475853451-22121-9-git-send-email-pantelis.antoniou@konsulko.com>
Date: Fri, 7 Oct 2016 18:17:29 +0300
From: Pantelis Antoniou <pantelis.antoniou@...sulko.com>
To: Lee Jones <lee.jones@...aro.org>
Cc: Rob Herring <robh+dt@...nel.org>,
Linus Walleij <linus.walleij@...aro.org>,
Alexandre Courbot <gnurou@...il.com>,
Mark Rutland <mark.rutland@....com>,
Frank Rowand <frowand.list@...il.com>,
Wolfram Sang <wsa@...-dreams.de>,
David Woodhouse <dwmw2@...radead.org>,
Brian Norris <computersforpeace@...il.com>,
Wim Van Sebroeck <wim@...ana.be>,
Guenter Roeck <linux@...ck-us.net>,
Peter Rosin <peda@...ntia.se>,
Debjit Ghosh <dghosh@...iper.net>,
Georgi Vlaev <gvlaev@...iper.net>,
Guenter Roeck <groeck@...iper.net>,
JawaharBalaji Thirumalaisamy <jawaharb@...iper.net>,
Rajat Jain <rajatjain@...iper.net>,
Pantelis Antoniou <pantelis.antoniou@...sulko.com>,
devicetree@...r.kernel.org, linux-kernel@...r.kernel.org,
linux-gpio@...r.kernel.org, linux-i2c@...r.kernel.org,
linux-mtd@...ts.infradead.org, linux-watchdog@...r.kernel.org
Subject: [PATCH 08/10] gpio: ptxpmb-cpld: Document bindings of PTXPMB's CPLD GPIO
From: Georgi Vlaev <gvlaev@...iper.net>
Add device tree bindings document for the GPIO driver of
Juniper's PTXPMB/NGPMB CPLD.
Signed-off-by: Georgi Vlaev <gvlaev@...iper.net>
[Ported from Juniper kernel]
Signed-off-by: Pantelis Antoniou <pantelis.antoniou@...sulko.com>
---
.../bindings/gpio/jnx,gpio-ptxpmb-cpld.txt | 30 ++++++++++++++++++++++
1 file changed, 30 insertions(+)
create mode 100644 Documentation/devicetree/bindings/gpio/jnx,gpio-ptxpmb-cpld.txt
diff --git a/Documentation/devicetree/bindings/gpio/jnx,gpio-ptxpmb-cpld.txt b/Documentation/devicetree/bindings/gpio/jnx,gpio-ptxpmb-cpld.txt
new file mode 100644
index 0000000..1122021
--- /dev/null
+++ b/Documentation/devicetree/bindings/gpio/jnx,gpio-ptxpmb-cpld.txt
@@ -0,0 +1,30 @@
+Juniper PTXPMB CPLD GPIO block
+
+Required properties:
+
+- compatible:
+ Must be "jnx,gpio-ptxpmb-cpld"
+
+- #gpio-cells:
+ Should be <2>. The first cell is the pin number (within the controller's
+ pin space), and the second is used for the following flags:
+ bit[0]: direction (0 = out, 1 = in)
+ bit[1]: init high
+ bit[2]: active low
+
+- gpio-controller:
+ Specifies that the node is a GPIO controller.
+
+Optional properties:
+
+- reg:
+ Address and length of the register set for the device. Usually supplied by
+ the parent MFD driver
+
+Example:
+
+gpio_cpld: cpld_gpio {
+ compatible = "jnx,gpio-ptxpmb-cpld";
+ #gpio-cells = <2>;
+ gpio-controller;
+};
--
1.9.1
Powered by blists - more mailing lists