| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-ID: <ac786510-74b2-f14c-b2a7-9c65fb07e40f@marvell.com>
Date: Sat, 8 Oct 2016 17:28:47 +0800
From: Ziji Hu <huziji@...vell.com>
To: Shawn Lin <shawn.lin@...k-chips.com>,
Gregory CLEMENT <gregory.clement@...e-electrons.com>,
Ulf Hansson <ulf.hansson@...aro.org>,
Adrian Hunter <adrian.hunter@...el.com>,
<linux-mmc@...r.kernel.org>
CC: Jason Cooper <jason@...edaemon.net>, Andrew Lunn <andrew@...n.ch>,
Sebastian Hesselbarth <sebastian.hesselbarth@...il.com>,
Rob Herring <robh+dt@...nel.org>, <devicetree@...r.kernel.org>,
Thomas Petazzoni <thomas.petazzoni@...e-electrons.com>,
<linux-arm-kernel@...ts.infradead.org>,
"Jack(SH) Zhu" <jmzhu@...vell.com>, Jimmy Xu <zmxu@...vell.com>,
Jisheng Zhang <jszhang@...vell.com>,
Nadav Haklai <nadavh@...vell.com>, Ryan Gao <ygao@...vell.com>,
Doug Jones <dougj@...vell.com>,
Shiwu Zhang <zhangshw@...vell.com>,
Victor Gu <xigu@...vell.com>,
"Wei(SOCP) Liu" <liuw@...vell.com>,
Wilson Ding <dingwei@...vell.com>,
Xueping Liu <xpliu@...vell.com>,
Hilbert Zhang <zzhang@...vell.com>,
Liuliu Zhao <zhaoliul@...vell.com>,
Peng Zhu <zhupeng@...vell.com>, Yu Cao <yucao@...vell.com>,
Romain Perier <romain.perier@...e-electrons.com>,
Yehuda Yitschak <yehuday@...vell.com>,
Marcin Wojtas <mw@...ihalf.com>,
Hanna Hawa <hannah@...vell.com>,
Kostya Porotchkin <kostap@...vell.com>,
<linux-kernel@...r.kernel.org>
Subject: Re: [PATCH 7/10] mmc: sdhci-xenon: Add support to PHYs of Marvell
Xenon SDHC
Hi Shawn,
On 2016/10/8 10:44, Shawn Lin wrote:
> 在 2016/10/7 23:22, Gregory CLEMENT 写道:
>> From: Ziji Hu <huziji@...vell.com>
>>
>> Marvell Xenon eMMC/SD/SDIO Host Controller contains PHY.
>> Three types of PHYs are supported.
>>
>> Add support to multiple types of PHYs init and configuration.
>> Add register definitions of PHYs.
>>
>> Signed-off-by: Hu Ziji <huziji@...vell.com>
>> Reviewed-by: Gregory CLEMENT <gregory.clement@...e-electrons.com>
>> Signed-off-by: Gregory CLEMENT <gregory.clement@...e-electrons.com>
>> ---
>> MAINTAINERS | 1 +-
>> drivers/mmc/host/Makefile | 2 +-
>> drivers/mmc/host/sdhci-xenon-phy.c | 1141 +++++++++++++++++++++++++++++-
>> drivers/mmc/host/sdhci-xenon-phy.h | 157 ++++-
>> drivers/mmc/host/sdhci-xenon.c | 4 +-
>> drivers/mmc/host/sdhci-xenon.h | 17 +-
>> 6 files changed, 1321 insertions(+), 1 deletion(-)
>> create mode 100644 drivers/mmc/host/sdhci-xenon-phy.c
>> create mode 100644 drivers/mmc/host/sdhci-xenon-phy.h
>>
>> diff --git a/MAINTAINERS b/MAINTAINERS
>> index 859420e5dfd3..b5673c2ee5f2 100644
>> --- a/MAINTAINERS
>> +++ b/MAINTAINERS
>> @@ -7583,6 +7583,7 @@ M: Ziji Hu <huziji@...vell.com>
>> L: linux-mmc@...r.kernel.org
>> S: Supported
>> F: drivers/mmc/host/sdhci-xenon.*
>> +F: drivers/mmc/host/sdhci-xenon-phy.*
>
> drivers/mmc/host/sdhci-xenon* shoube enough
>
>> F: Documentation/devicetree/bindings/mmc/marvell,sdhci-xenon.txt
>>
>> MATROX FRAMEBUFFER DRIVER
>> diff --git a/drivers/mmc/host/Makefile b/drivers/mmc/host/Makefile
>> index 75eaf743486c..4f2854556ff7 100644
>> --- a/drivers/mmc/host/Makefile
>> +++ b/drivers/mmc/host/Makefile
>> @@ -82,4 +82,4 @@ ifeq ($(CONFIG_CB710_DEBUG),y)
>> endif
>>
>> obj-$(CONFIG_MMC_SDHCI_XENON) += sdhci-xenon-driver.o
>> -sdhci-xenon-driver-y += sdhci-xenon.o
>> +sdhci-xenon-driver-y += sdhci-xenon.o sdhci-xenon-phy.o
>> diff --git a/drivers/mmc/host/sdhci-xenon-phy.c b/drivers/mmc/host/sdhci-xenon-phy.c
>> new file mode 100644
>> index 000000000000..4eb8fea1bec9
>> --- /dev/null
>> +++ b/drivers/mmc/host/sdhci-xenon-phy.c
>
> Well, it's legit to use phy API and move your phy
> operations to PHY subsystem. :)
>
Actually we tried to put the PHY code into Linux PHY framework.
But it cannot fit in Linux common PHY framework.
Our Xenon SDHC PHY register is a part of Xenon SDHC register set.
Besides, during MMC initialization, MMC sequence has to call several PHY functions to complete timing setting.
In those PHY setting functions, they have to access SDHC register and know current MMC setting, such as bus width, clock frequency and speed mode.
As a result, we have to implement PHY under MMC directory.
Thank you.
Best regards,
Hu Ziji
>> @@ -0,0 +1,1141 @@
>> +/*
>> + * PHY support for Xenon SDHC
>> + *
>> + * Copyright (C) 2016 Marvell, All Rights Reserved.
>> + *
>> + * Author: Hu Ziji <huziji@...vell.com>
>> + * Date: 2016-8-24
>> + *
>> + * This program is free software; you can redistribute it and/or
>> + * modify it under the terms of the GNU General Public License as
>> + * published by the Free Software Foundation version 2.
>> + */
>> +
>> +#include <linux/slab.h>
>> +#include <linux/delay.h>
>> +#include <linux/of_address.h>
>> +#include <linux/mmc/host.h>
>> +#include <linux/mmc/mmc.h>
>> +#include <linux/mmc/card.h>
>> +#include <linux/mmc/sdio.h>
>> +
>> +#include "sdhci.h"
>> +#include "sdhci-pltfm.h"
>> +#include "sdhci-xenon.h"
>> +
>> +static const char * const phy_types[] = {
>> + "sdh phy",
>> + "emmc 5.0 phy",
>> + "emmc 5.1 phy"
>> +};
>> +
>> +enum phy_type_enum {
>> + SDH_PHY,
>> + EMMC_5_0_PHY,
>> + EMMC_5_1_PHY,
>> + NR_PHY_TYPES
>> +};
>> +
>> +struct soc_pad_ctrl_table {
>> + const char *soc;
>> + void (*set_soc_pad)(struct sdhci_host *host,
>> + unsigned char signal_voltage);
>> +};
>> +
>> +struct soc_pad_ctrl {
>> + /* Register address of SOC PHY PAD ctrl */
>> + void __iomem *reg;
>> + /* SOC PHY PAD ctrl type */
>> + enum soc_pad_ctrl_type pad_type;
>> + /* SOC specific operation to set SOC PHY PAD */
>> + void (*set_soc_pad)(struct sdhci_host *host,
>> + unsigned char signal_voltage);
>> +};
>> +
>> +static struct xenon_emmc_phy_regs xenon_emmc_5_0_phy_regs = {
>> + .timing_adj = EMMC_5_0_PHY_TIMING_ADJUST,
>> + .func_ctrl = EMMC_5_0_PHY_FUNC_CONTROL,
>> + .pad_ctrl = EMMC_5_0_PHY_PAD_CONTROL,
>> + .pad_ctrl2 = EMMC_5_0_PHY_PAD_CONTROL2,
>> + .dll_ctrl = EMMC_5_0_PHY_DLL_CONTROL,
>> + .logic_timing_adj = EMMC_5_0_PHY_LOGIC_TIMING_ADJUST,
>> + .delay_mask = EMMC_5_0_PHY_FIXED_DELAY_MASK,
>> + .dll_update = DLL_UPDATE_STROBE_5_0,
>> +};
>> +
>> +static struct xenon_emmc_phy_regs xenon_emmc_5_1_phy_regs = {
>> + .timing_adj = EMMC_PHY_TIMING_ADJUST,
>> + .func_ctrl = EMMC_PHY_FUNC_CONTROL,
>> + .pad_ctrl = EMMC_PHY_PAD_CONTROL,
>> + .pad_ctrl2 = EMMC_PHY_PAD_CONTROL2,
>> + .dll_ctrl = EMMC_PHY_DLL_CONTROL,
>> + .logic_timing_adj = EMMC_PHY_LOGIC_TIMING_ADJUST,
>> + .delay_mask = EMMC_PHY_FIXED_DELAY_MASK,
>> + .dll_update = DLL_UPDATE,
>> +};
>> +
>> +static int xenon_delay_adj_test(struct mmc_card *card);
>> +
>> +/*
>> + * eMMC PHY configuration and operations
>> + */
>> +struct emmc_phy_params {
>> + bool slow_mode;
>> +
>> + u8 znr;
>> + u8 zpr;
>> +
>> + /* Nr of consecutive Sampling Points of a Valid Sampling Window */
>> + u8 nr_tun_times;
>> + /* Divider for calculating Tuning Step */
>> + u8 tun_step_divider;
>> +
>> + struct soc_pad_ctrl pad_ctrl;
>> +};
>> +
>> +static void xenon_emmc_phy_strobe_delay_adj(struct sdhci_host *host,
>> + struct mmc_card *card);
>> +static int xenon_emmc_phy_fix_sampl_delay_adj(struct sdhci_host *host,
>> + struct mmc_card *card);
>> +static void xenon_emmc_phy_set(struct sdhci_host *host,
>> + unsigned char timing);
>> +static void xenon_emmc_set_soc_pad(struct sdhci_host *host,
>> + unsigned char signal_voltage);
>> +
>> +static const struct xenon_phy_ops emmc_phy_ops = {
>> + .strobe_delay_adj = xenon_emmc_phy_strobe_delay_adj,
>> + .fix_sampl_delay_adj = xenon_emmc_phy_fix_sampl_delay_adj,
>> + .phy_set = xenon_emmc_phy_set,
>> + .set_soc_pad = xenon_emmc_set_soc_pad,
>> +};
>> +
>> +static int alloc_emmc_phy(struct sdhci_xenon_priv *priv)
>> +{
>> + struct emmc_phy_params *params;
>> +
>> + params = kzalloc(sizeof(*params), GFP_KERNEL);
>> + if (!params)
>> + return -ENOMEM;
>> +
>> + priv->phy_params = params;
>> + priv->phy_ops = &emmc_phy_ops;
>> + if (priv->phy_type == EMMC_5_0_PHY)
>> + priv->emmc_phy_regs = &xenon_emmc_5_0_phy_regs;
>> + else
>> + priv->emmc_phy_regs = &xenon_emmc_5_1_phy_regs;
>> +
>> + return 0;
>> +}
>> +
>> +static int xenon_emmc_phy_init(struct sdhci_host *host)
>> +{
>> + u32 reg;
>> + u32 wait, clock;
>> + struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
>> + struct sdhci_xenon_priv *priv = sdhci_pltfm_priv(pltfm_host);
>> + struct xenon_emmc_phy_regs *phy_regs = priv->emmc_phy_regs;
>> +
>> + reg = sdhci_readl(host, phy_regs->timing_adj);
>> + reg |= PHY_INITIALIZAION;
>> + sdhci_writel(host, reg, phy_regs->timing_adj);
>> +
>> + /* Add duration of FC_SYNC_RST */
>> + wait = ((reg >> FC_SYNC_RST_DURATION_SHIFT) &
>> + FC_SYNC_RST_DURATION_MASK);
>> + /* Add interval between FC_SYNC_EN and FC_SYNC_RST */
>> + wait += ((reg >> FC_SYNC_RST_EN_DURATION_SHIFT) &
>> + FC_SYNC_RST_EN_DURATION_MASK);
>> + /* Add duration of asserting FC_SYNC_EN */
>> + wait += ((reg >> FC_SYNC_EN_DURATION_SHIFT) &
>> + FC_SYNC_EN_DURATION_MASK);
>> + /* Add duration of waiting for PHY */
>> + wait += ((reg >> WAIT_CYCLE_BEFORE_USING_SHIFT) &
>> + WAIT_CYCLE_BEFORE_USING_MASK);
>> + /* 4 addtional bus clock and 4 AXI bus clock are required */
>> + wait += 8;
>> + wait <<= 20;
>> +
>> + clock = host->clock;
>> + if (!clock)
>> + /* Use the possibly slowest bus frequency value */
>> + clock = LOWEST_SDCLK_FREQ;
>> + /* get the wait time */
>> + wait /= clock;
>> + wait++;
>> + /* wait for host eMMC PHY init completes */
>> + udelay(wait);
>> +
>> + reg = sdhci_readl(host, phy_regs->timing_adj);
>> + reg &= PHY_INITIALIZAION;
>> + if (reg) {
>> + dev_err(mmc_dev(host->mmc), "eMMC PHY init cannot complete after %d us\n",
>> + wait);
>> + return -ETIMEDOUT;
>> + }
>> +
>> + return 0;
>> +}
>> +
>> +#define ARMADA_3700_SOC_PAD_1_8V 0x1
>> +#define ARMADA_3700_SOC_PAD_3_3V 0x0
>> +
>> +static void armada_3700_soc_pad_voltage_set(struct sdhci_host *host,
>> + unsigned char signal_voltage)
>> +{
>> + struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
>> + struct sdhci_xenon_priv *priv = sdhci_pltfm_priv(pltfm_host);
>> + struct emmc_phy_params *params = priv->phy_params;
>> +
>> + if (params->pad_ctrl.pad_type == SOC_PAD_FIXED_1_8V) {
>> + writel(ARMADA_3700_SOC_PAD_1_8V, params->pad_ctrl.reg);
>> + } else if (params->pad_ctrl.pad_type == SOC_PAD_SD) {
>> + if (signal_voltage == MMC_SIGNAL_VOLTAGE_180)
>> + writel(ARMADA_3700_SOC_PAD_1_8V, params->pad_ctrl.reg);
>> + else if (signal_voltage == MMC_SIGNAL_VOLTAGE_330)
>> + writel(ARMADA_3700_SOC_PAD_3_3V, params->pad_ctrl.reg);
>> + }
>> +}
>> +
>> +static void xenon_emmc_set_soc_pad(struct sdhci_host *host,
>> + unsigned char signal_voltage)
>> +{
>> + struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
>> + struct sdhci_xenon_priv *priv = sdhci_pltfm_priv(pltfm_host);
>> + struct emmc_phy_params *params = priv->phy_params;
>> +
>> + if (!params->pad_ctrl.reg)
>> + return;
>> +
>> + if (params->pad_ctrl.set_soc_pad)
>> + params->pad_ctrl.set_soc_pad(host, signal_voltage);
>> +}
>> +
>> +static int emmc_phy_set_fix_sampl_delay(struct sdhci_host *host,
>> + unsigned int delay,
>> + bool invert,
>> + bool delay_90_degree)
>> +{
>> + u32 reg;
>> + unsigned long flags;
>> + struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
>> + struct sdhci_xenon_priv *priv = sdhci_pltfm_priv(pltfm_host);
>> + struct xenon_emmc_phy_regs *phy_regs = priv->emmc_phy_regs;
>> + int ret = 0;
>> +
>> + spin_lock_irqsave(&host->lock, flags);
>> +
>> + /* Setup Sampling fix delay */
>> + reg = sdhci_readl(host, SDHC_SLOT_OP_STATUS_CTRL);
>> + reg &= ~phy_regs->delay_mask;
>> + reg |= delay & phy_regs->delay_mask;
>> + sdhci_writel(host, reg, SDHC_SLOT_OP_STATUS_CTRL);
>> +
>> + if (priv->phy_type == EMMC_5_0_PHY) {
>> + /* set 90 degree phase if necessary */
>> + reg &= ~DELAY_90_DEGREE_MASK_EMMC5;
>> + reg |= (delay_90_degree << DELAY_90_DEGREE_SHIFT_EMMC5);
>> + sdhci_writel(host, reg, SDHC_SLOT_OP_STATUS_CTRL);
>> + }
>> +
>> + /* Disable SDCLK */
>> + reg = sdhci_readl(host, SDHCI_CLOCK_CONTROL);
>> + reg &= ~(SDHCI_CLOCK_CARD_EN | SDHCI_CLOCK_INT_EN);
>> + sdhci_writel(host, reg, SDHCI_CLOCK_CONTROL);
>> +
>> + udelay(200);
>> +
>> + if (priv->phy_type == EMMC_5_1_PHY) {
>> + /* set 90 degree phase if necessary */
>> + reg = sdhci_readl(host, EMMC_PHY_FUNC_CONTROL);
>> + reg &= ~ASYNC_DDRMODE_MASK;
>> + reg |= (delay_90_degree << ASYNC_DDRMODE_SHIFT);
>> + sdhci_writel(host, reg, EMMC_PHY_FUNC_CONTROL);
>> + }
>> +
>> + /* Setup Inversion of Sampling edge */
>> + reg = sdhci_readl(host, phy_regs->timing_adj);
>> + reg &= ~SAMPL_INV_QSP_PHASE_SELECT;
>> + reg |= (invert << SAMPL_INV_QSP_PHASE_SELECT_SHIFT);
>> + sdhci_writel(host, reg, phy_regs->timing_adj);
>> +
>> + /* Enable SD internal clock */
>> + ret = enable_xenon_internal_clk(host);
>> + if (ret)
>> + goto out;
>> +
>> + /* Enable SDCLK */
>> + reg = sdhci_readl(host, SDHCI_CLOCK_CONTROL);
>> + reg |= SDHCI_CLOCK_CARD_EN;
>> + sdhci_writel(host, reg, SDHCI_CLOCK_CONTROL);
>> +
>> + udelay(200);
>> +
>> + /*
>> + * Has to re-initialize eMMC PHY here to active PHY
>> + * because later get status cmd will be issued.
>> + */
>> + ret = xenon_emmc_phy_init(host);
>> +
>> +out:
>> + spin_unlock_irqrestore(&host->lock, flags);
>> + return ret;
>> +}
>> +
>> +static int emmc_phy_do_fix_sampl_delay(struct sdhci_host *host,
>> + struct mmc_card *card,
>> + unsigned int delay,
>> + bool invert, bool quarter)
>> +{
>> + int ret;
>> +
>> + emmc_phy_set_fix_sampl_delay(host, delay, invert, quarter);
>> +
>> + ret = xenon_delay_adj_test(card);
>> + if (ret) {
>> + dev_dbg(mmc_dev(host->mmc),
>> + "fail when sampling fix delay = %d, phase = %d degree\n",
>> + delay, invert * 180 + quarter * 90);
>> + return -1;
>> + }
>> + return 0;
>> +}
>> +
>> +static int xenon_emmc_phy_fix_sampl_delay_adj(struct sdhci_host *host,
>> + struct mmc_card *card)
>> +{
>> + enum sampl_fix_delay_phase phase;
>> + int idx, nr_pair;
>> + int ret;
>> + unsigned int delay;
>> + unsigned int min_delay, max_delay;
>> + bool invert, quarter;
>> + struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
>> + struct sdhci_xenon_priv *priv = sdhci_pltfm_priv(pltfm_host);
>> + struct xenon_emmc_phy_regs *phy_regs = priv->emmc_phy_regs;
>> + u32 coarse_step, fine_step;
>> + const enum sampl_fix_delay_phase delay_edge[] = {
>> + PHASE_0_DEGREE,
>> + PHASE_180_DEGREE,
>> + PHASE_90_DEGREE,
>> + PHASE_270_DEGREE
>> + };
>> +
>> + coarse_step = phy_regs->delay_mask >> 1;
>> + fine_step = coarse_step >> 2;
>> +
>> + nr_pair = ARRAY_SIZE(delay_edge);
>> +
>> + for (idx = 0; idx < nr_pair; idx++) {
>> + phase = delay_edge[idx];
>> + invert = (phase & 0x2) ? true : false;
>> + quarter = (phase & 0x1) ? true : false;
>> +
>> + /* increase delay value to get fix delay */
>> + for (min_delay = 0;
>> + min_delay <= phy_regs->delay_mask;
>> + min_delay += coarse_step) {
>> + ret = emmc_phy_do_fix_sampl_delay(host, card, min_delay,
>> + invert, quarter);
>> + if (!ret)
>> + break;
>> + }
>> +
>> + if (ret) {
>> + dev_dbg(mmc_dev(host->mmc),
>> + "Fail to set Sampling Fixed Delay with phase = %d degree\n",
>> + phase * 90);
>> + continue;
>> + }
>> +
>> + for (max_delay = min_delay + fine_step;
>> + max_delay < phy_regs->delay_mask;
>> + max_delay += fine_step) {
>> + ret = emmc_phy_do_fix_sampl_delay(host, card, max_delay,
>> + invert, quarter);
>> + if (ret) {
>> + max_delay -= fine_step;
>> + break;
>> + }
>> + }
>> +
>> + if (!ret) {
>> + ret = emmc_phy_do_fix_sampl_delay(host, card,
>> + phy_regs->delay_mask,
>> + invert, quarter);
>> + if (!ret)
>> + max_delay = phy_regs->delay_mask;
>> + }
>> +
>> + /*
>> + * Sampling Fixed Delay line window should be large enough,
>> + * thus the sampling point (the middle of the window)
>> + * can work when environment varies.
>> + * However, there is no clear conclusion how large the window
>> + * should be.
>> + */
>> + if ((max_delay - min_delay) <=
>> + EMMC_PHY_FIXED_DELAY_WINDOW_MIN) {
>> + dev_info(mmc_dev(host->mmc),
>> + "The window size %d with phase = %d degree is too small\n",
>> + max_delay - min_delay, phase * 90);
>> + continue;
>> + }
>> +
>> + delay = (min_delay + max_delay) / 2;
>> + emmc_phy_set_fix_sampl_delay(host, delay, invert, quarter);
>> + dev_dbg(mmc_dev(host->mmc),
>> + "sampling fix delay = %d with phase = %d degree\n",
>> + delay, phase * 90);
>> + return 0;
>> + }
>> +
>> + return -EIO;
>> +}
>> +
>> +static int xenon_emmc_phy_enable_dll(struct sdhci_host *host)
>> +{
>> + u32 reg;
>> + struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
>> + struct sdhci_xenon_priv *priv = sdhci_pltfm_priv(pltfm_host);
>> + struct xenon_emmc_phy_regs *phy_regs = priv->emmc_phy_regs;
>> + u8 timeout;
>> +
>> + if (WARN_ON(host->clock <= MMC_HIGH_52_MAX_DTR))
>> + return -EINVAL;
>> +
>> + reg = sdhci_readl(host, phy_regs->dll_ctrl);
>> + if (reg & DLL_ENABLE)
>> + return 0;
>> +
>> + /* Enable DLL */
>> + reg = sdhci_readl(host, phy_regs->dll_ctrl);
>> + reg |= (DLL_ENABLE | DLL_FAST_LOCK);
>> +
>> + /*
>> + * Set Phase as 90 degree, which is most common value.
>> + * Might set another value if necessary.
>> + * The granularity is 1 degree.
>> + */
>> + reg &= ~((DLL_PHASE_MASK << DLL_PHSEL0_SHIFT) |
>> + (DLL_PHASE_MASK << DLL_PHSEL1_SHIFT));
>> + reg |= ((DLL_PHASE_90_DEGREE << DLL_PHSEL0_SHIFT) |
>> + (DLL_PHASE_90_DEGREE << DLL_PHSEL1_SHIFT));
>> +
>> + reg &= ~DLL_BYPASS_EN;
>> + reg |= phy_regs->dll_update;
>> + if (priv->phy_type == EMMC_5_1_PHY)
>> + reg &= ~DLL_REFCLK_SEL;
>> + sdhci_writel(host, reg, phy_regs->dll_ctrl);
>> +
>> + /* Wait max 32 ms */
>> + timeout = 32;
>> + while (!(sdhci_readw(host, SDHC_SLOT_EXT_PRESENT_STATE) & LOCK_STATE)) {
>> + if (!timeout) {
>> + dev_err(mmc_dev(host->mmc), "Wait for DLL Lock time-out\n");
>> + return -ETIMEDOUT;
>> + }
>> + timeout--;
>> + mdelay(1);
>> + }
>> + return 0;
>> +}
>> +
>> +static int __emmc_phy_config_tuning(struct sdhci_host *host)
>> +{
>> + struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
>> + struct sdhci_xenon_priv *priv = sdhci_pltfm_priv(pltfm_host);
>> + struct emmc_phy_params *params = priv->phy_params;
>> + u32 reg, tuning_step;
>> + int ret;
>> + unsigned long flags;
>> +
>> + if (WARN_ON(host->clock <= MMC_HIGH_52_MAX_DTR))
>> + return -EINVAL;
>> +
>> + spin_lock_irqsave(&host->lock, flags);
>> +
>> + ret = xenon_emmc_phy_enable_dll(host);
>> + if (ret) {
>> + spin_unlock_irqrestore(&host->lock, flags);
>> + return ret;
>> + }
>> +
>> + reg = sdhci_readl(host, SDHC_SLOT_DLL_CUR_DLY_VAL);
>> + tuning_step = reg / params->tun_step_divider;
>> + if (unlikely(tuning_step > TUNING_STEP_MASK)) {
>> + dev_warn(mmc_dev(host->mmc),
>> + "HS200 TUNING_STEP %d is larger than MAX value\n",
>> + tuning_step);
>> + tuning_step = TUNING_STEP_MASK;
>> + }
>> +
>> + reg = sdhci_readl(host, SDHC_SLOT_OP_STATUS_CTRL);
>> + reg &= ~(TUN_CONSECUTIVE_TIMES_MASK << TUN_CONSECUTIVE_TIMES_SHIFT);
>> + reg |= (params->nr_tun_times << TUN_CONSECUTIVE_TIMES_SHIFT);
>> + reg &= ~(TUNING_STEP_MASK << TUNING_STEP_SHIFT);
>> + reg |= (tuning_step << TUNING_STEP_SHIFT);
>> + sdhci_writel(host, reg, SDHC_SLOT_OP_STATUS_CTRL);
>> +
>> + spin_unlock_irqrestore(&host->lock, flags);
>> + return 0;
>> +}
>> +
>> +static int xenon_emmc_phy_config_tuning(struct sdhci_host *host)
>> +{
>> + return __emmc_phy_config_tuning(host);
>> +}
>> +
>> +static void xenon_emmc_phy_strobe_delay_adj(struct sdhci_host *host,
>> + struct mmc_card *card)
>> +{
>> + u32 reg;
>> + struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
>> + struct sdhci_xenon_priv *priv = sdhci_pltfm_priv(pltfm_host);
>> + unsigned long flags;
>> +
>> + if (host->clock <= MMC_HIGH_52_MAX_DTR)
>> + return;
>> +
>> + dev_dbg(mmc_dev(host->mmc), "starts HS400 strobe delay adjustment\n");
>> +
>> + spin_lock_irqsave(&host->lock, flags);
>> +
>> + xenon_emmc_phy_enable_dll(host);
>> +
>> + /* Enable SDHC Data Strobe */
>> + reg = sdhci_readl(host, SDHC_SLOT_EMMC_CTRL);
>> + reg |= ENABLE_DATA_STROBE;
>> + sdhci_writel(host, reg, SDHC_SLOT_EMMC_CTRL);
>> +
>> + /* Set Data Strobe Pull down */
>> + if (priv->phy_type == EMMC_5_0_PHY) {
>> + reg = sdhci_readl(host, EMMC_5_0_PHY_PAD_CONTROL);
>> + reg |= EMMC5_FC_QSP_PD;
>> + reg &= ~EMMC5_FC_QSP_PU;
>> + sdhci_writel(host, reg, EMMC_5_0_PHY_PAD_CONTROL);
>> + } else {
>> + reg = sdhci_readl(host, EMMC_PHY_PAD_CONTROL1);
>> + reg |= EMMC5_1_FC_QSP_PD;
>> + reg &= ~EMMC5_1_FC_QSP_PU;
>> + sdhci_writel(host, reg, EMMC_PHY_PAD_CONTROL1);
>> + }
>> + spin_unlock_irqrestore(&host->lock, flags);
>> +}
>> +
>> +#define LOGIC_TIMING_VALUE 0x00AA8977
>> +
>> +static void xenon_emmc_phy_set(struct sdhci_host *host,
>> + unsigned char timing)
>> +{
>> + u32 reg;
>> + struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
>> + struct sdhci_xenon_priv *priv = sdhci_pltfm_priv(pltfm_host);
>> + struct emmc_phy_params *params = priv->phy_params;
>> + struct xenon_emmc_phy_regs *phy_regs = priv->emmc_phy_regs;
>> + struct mmc_card *card = priv->card_candidate;
>> + unsigned long flags;
>> +
>> + dev_dbg(mmc_dev(host->mmc), "eMMC PHY setting starts\n");
>> +
>> + spin_lock_irqsave(&host->lock, flags);
>> +
>> + /* Setup pad, set bit[28] and bits[26:24] */
>> + reg = sdhci_readl(host, phy_regs->pad_ctrl);
>> + reg |= (FC_DQ_RECEN | FC_CMD_RECEN | FC_QSP_RECEN | OEN_QSN);
>> + /*
>> + * All FC_XX_RECEIVCE should be set as CMOS Type
>> + */
>> + reg |= FC_ALL_CMOS_RECEIVER;
>> + sdhci_writel(host, reg, phy_regs->pad_ctrl);
>> +
>> + /* Set CMD and DQ Pull Up */
>> + if (priv->phy_type == EMMC_5_0_PHY) {
>> + reg = sdhci_readl(host, EMMC_5_0_PHY_PAD_CONTROL);
>> + reg |= (EMMC5_FC_CMD_PU | EMMC5_FC_DQ_PU);
>> + reg &= ~(EMMC5_FC_CMD_PD | EMMC5_FC_DQ_PD);
>> + sdhci_writel(host, reg, EMMC_5_0_PHY_PAD_CONTROL);
>> + } else {
>> + reg = sdhci_readl(host, EMMC_PHY_PAD_CONTROL1);
>> + reg |= (EMMC5_1_FC_CMD_PU | EMMC5_1_FC_DQ_PU);
>> + reg &= ~(EMMC5_1_FC_CMD_PD | EMMC5_1_FC_DQ_PD);
>> + sdhci_writel(host, reg, EMMC_PHY_PAD_CONTROL1);
>> + }
>> +
>> + if ((timing == MMC_TIMING_LEGACY) || !card)
>> + goto phy_init;
>> +
>> + /*
>> + * FIXME: should depends on the specific board timing.
>> + */
>> + if ((timing == MMC_TIMING_MMC_HS400) ||
>> + (timing == MMC_TIMING_MMC_HS200) ||
>> + (timing == MMC_TIMING_UHS_SDR50) ||
>> + (timing == MMC_TIMING_UHS_SDR104) ||
>> + (timing == MMC_TIMING_UHS_DDR50) ||
>> + (timing == MMC_TIMING_UHS_SDR25) ||
>> + (timing == MMC_TIMING_MMC_DDR52)) {
>> + reg = sdhci_readl(host, phy_regs->timing_adj);
>> + reg &= ~OUTPUT_QSN_PHASE_SELECT;
>> + sdhci_writel(host, reg, phy_regs->timing_adj);
>> + }
>> +
>> + /*
>> + * If SDIO card, set SDIO Mode
>> + * Otherwise, clear SDIO Mode and Slow Mode
>> + */
>> + if (mmc_card_sdio(card)) {
>> + reg = sdhci_readl(host, phy_regs->timing_adj);
>> + reg |= TIMING_ADJUST_SDIO_MODE;
>> +
>> + if ((timing == MMC_TIMING_UHS_SDR25) ||
>> + (timing == MMC_TIMING_UHS_SDR12) ||
>> + (timing == MMC_TIMING_SD_HS) ||
>> + (timing == MMC_TIMING_LEGACY))
>> + reg |= TIMING_ADJUST_SLOW_MODE;
>> +
>> + sdhci_writel(host, reg, phy_regs->timing_adj);
>> + } else {
>> + reg = sdhci_readl(host, phy_regs->timing_adj);
>> + reg &= ~(TIMING_ADJUST_SDIO_MODE | TIMING_ADJUST_SLOW_MODE);
>> + sdhci_writel(host, reg, phy_regs->timing_adj);
>> + }
>> +
>> + if (((timing == MMC_TIMING_UHS_SDR50) ||
>> + (timing == MMC_TIMING_UHS_SDR25) ||
>> + (timing == MMC_TIMING_UHS_SDR12) ||
>> + (timing == MMC_TIMING_SD_HS) ||
>> + (timing == MMC_TIMING_MMC_HS) ||
>> + (timing == MMC_TIMING_LEGACY)) && params->slow_mode) {
>> + reg = sdhci_readl(host, phy_regs->timing_adj);
>> + reg |= TIMING_ADJUST_SLOW_MODE;
>> + sdhci_writel(host, reg, phy_regs->timing_adj);
>> + }
>> +
>> + /*
>> + * Set preferred ZNR and ZPR value
>> + * The ZNR and ZPR value vary between different boards.
>> + * Define them both in sdhci-xenon-emmc-phy.h.
>> + */
>> + reg = sdhci_readl(host, phy_regs->pad_ctrl2);
>> + reg &= ~((ZNR_MASK << ZNR_SHIFT) | ZPR_MASK);
>> + reg |= ((params->znr << ZNR_SHIFT) | params->zpr);
>> + sdhci_writel(host, reg, phy_regs->pad_ctrl2);
>> +
>> + /*
>> + * When setting EMMC_PHY_FUNC_CONTROL register,
>> + * SD clock should be disabled
>> + */
>> + reg = sdhci_readl(host, SDHCI_CLOCK_CONTROL);
>> + reg &= ~SDHCI_CLOCK_CARD_EN;
>> + sdhci_writew(host, reg, SDHCI_CLOCK_CONTROL);
>> +
>> + if ((timing == MMC_TIMING_UHS_DDR50) ||
>> + (timing == MMC_TIMING_MMC_HS400) ||
>> + (timing == MMC_TIMING_MMC_DDR52)) {
>> + reg = sdhci_readl(host, phy_regs->func_ctrl);
>> + reg |= (DQ_DDR_MODE_MASK << DQ_DDR_MODE_SHIFT) | CMD_DDR_MODE;
>> + sdhci_writel(host, reg, phy_regs->func_ctrl);
>> + }
>> +
>> + if (timing == MMC_TIMING_MMC_HS400) {
>> + reg = sdhci_readl(host, phy_regs->func_ctrl);
>> + reg &= ~DQ_ASYNC_MODE;
>> + sdhci_writel(host, reg, phy_regs->func_ctrl);
>> + }
>> +
>> + /* Enable bus clock */
>> + reg = sdhci_readl(host, SDHCI_CLOCK_CONTROL);
>> + reg |= SDHCI_CLOCK_CARD_EN;
>> + sdhci_writew(host, reg, SDHCI_CLOCK_CONTROL);
>> +
>> + if (timing == MMC_TIMING_MMC_HS400)
>> + /* Hardware team recommend a value for HS400 */
>> + sdhci_writel(host, LOGIC_TIMING_VALUE,
>> + phy_regs->logic_timing_adj);
>> +
>> +phy_init:
>> + xenon_emmc_phy_init(host);
>> +
>> + spin_unlock_irqrestore(&host->lock, flags);
>> +
>> + dev_dbg(mmc_dev(host->mmc), "eMMC PHY setting completes\n");
>> +}
>> +
>> +static int get_dt_pad_ctrl_data(struct sdhci_host *host,
>> + struct device_node *np,
>> + struct emmc_phy_params *params)
>> +{
>> + int ret = 0;
>> + const char *name;
>> + struct resource iomem;
>> +
>> + if (of_device_is_compatible(np, "marvell,armada-3700-sdhci"))
>> + params->pad_ctrl.set_soc_pad = armada_3700_soc_pad_voltage_set;
>> + else
>> + return 0;
>> +
>> + if (of_address_to_resource(np, 1, &iomem)) {
>> + dev_err(mmc_dev(host->mmc), "Unable to find SOC PAD ctrl register address for %s\n",
>> + np->name);
>> + return -EINVAL;
>> + }
>> +
>> + params->pad_ctrl.reg = devm_ioremap_resource(mmc_dev(host->mmc),
>> + &iomem);
>> + if (IS_ERR(params->pad_ctrl.reg)) {
>> + dev_err(mmc_dev(host->mmc), "Unable to get SOC PHY PAD ctrl regiser for %s\n",
>> + np->name);
>> + return PTR_ERR(params->pad_ctrl.reg);
>> + }
>> +
>> + ret = of_property_read_string(np, "xenon,pad-type", &name);
>> + if (ret) {
>> + dev_err(mmc_dev(host->mmc), "Unable to determine SOC PHY PAD ctrl type\n");
>> + return ret;
>> + }
>> + if (!strcmp(name, "sd")) {
>> + params->pad_ctrl.pad_type = SOC_PAD_SD;
>> + } else if (!strcmp(name, "fixed-1-8v")) {
>> + params->pad_ctrl.pad_type = SOC_PAD_FIXED_1_8V;
>> + } else {
>> + dev_err(mmc_dev(host->mmc), "Unsupported SOC PHY PAD ctrl type %s\n",
>> + name);
>> + return -EINVAL;
>> + }
>> +
>> + return ret;
>> +}
>> +
>> +static int emmc_phy_parse_param_dt(struct sdhci_host *host,
>> + struct device_node *np,
>> + struct emmc_phy_params *params)
>> +{
>> + u32 value;
>> +
>> + if (of_property_read_bool(np, "xenon,phy-slow-mode"))
>> + params->slow_mode = true;
>> + else
>> + params->slow_mode = false;
>> +
>> + if (!of_property_read_u32(np, "xenon,phy-znr", &value))
>> + params->znr = value & ZNR_MASK;
>> + else
>> + params->znr = ZNR_DEF_VALUE;
>> +
>> + if (!of_property_read_u32(np, "xenon,phy-zpr", &value))
>> + params->zpr = value & ZPR_MASK;
>> + else
>> + params->zpr = ZPR_DEF_VALUE;
>> +
>> + if (!of_property_read_u32(np, "xenon,phy-nr-tun-times", &value))
>> + params->nr_tun_times = value & TUN_CONSECUTIVE_TIMES_MASK;
>> + else
>> + params->nr_tun_times = TUN_CONSECUTIVE_TIMES;
>> +
>> + if (!of_property_read_u32(np, "xenon,phy-tun-step-divider", &value))
>> + params->tun_step_divider = value & 0xFF;
>> + else
>> + params->tun_step_divider = TUNING_STEP_DIVIDER;
>> +
>> + return get_dt_pad_ctrl_data(host, np, params);
>> +}
>> +
>> +/*
>> + * SDH PHY configuration and operations
>> + */
>> +static int xenon_sdh_phy_set_fix_sampl_delay(struct sdhci_host *host,
>> + unsigned int delay, bool invert)
>> +{
>> + u32 reg;
>> + unsigned long flags;
>> + int ret;
>> +
>> + if (invert)
>> + invert = 0x1;
>> + else
>> + invert = 0x0;
>> +
>> + spin_lock_irqsave(&host->lock, flags);
>> +
>> + /* Disable SDCLK */
>> + reg = sdhci_readl(host, SDHCI_CLOCK_CONTROL);
>> + reg &= ~(SDHCI_CLOCK_CARD_EN | SDHCI_CLOCK_INT_EN);
>> + sdhci_writel(host, reg, SDHCI_CLOCK_CONTROL);
>> +
>> + udelay(200);
>> +
>> + /* Setup Sampling fix delay */
>> + reg = sdhci_readl(host, SDHC_SLOT_OP_STATUS_CTRL);
>> + reg &= ~(SDH_PHY_FIXED_DELAY_MASK |
>> + (0x1 << FORCE_SEL_INVERSE_CLK_SHIFT));
>> + reg |= ((delay & SDH_PHY_FIXED_DELAY_MASK) |
>> + (invert << FORCE_SEL_INVERSE_CLK_SHIFT));
>> + sdhci_writel(host, reg, SDHC_SLOT_OP_STATUS_CTRL);
>> +
>> + /* Enable SD internal clock */
>> + ret = enable_xenon_internal_clk(host);
>> +
>> + /* Enable SDCLK */
>> + reg = sdhci_readl(host, SDHCI_CLOCK_CONTROL);
>> + reg |= SDHCI_CLOCK_CARD_EN;
>> + sdhci_writel(host, reg, SDHCI_CLOCK_CONTROL);
>> +
>> + udelay(200);
>> +
>> + spin_unlock_irqrestore(&host->lock, flags);
>> + return ret;
>> +}
>> +
>> +static int sdh_phy_do_fix_sampl_delay(struct sdhci_host *host,
>> + struct mmc_card *card,
>> + unsigned int delay, bool invert)
>> +{
>> + int ret;
>> +
>> + xenon_sdh_phy_set_fix_sampl_delay(host, delay, invert);
>> +
>> + ret = xenon_delay_adj_test(card);
>> + if (ret) {
>> + dev_dbg(mmc_dev(host->mmc),
>> + "fail when sampling fix delay = %d, phase = %d degree\n",
>> + delay, invert * 180);
>> + return -1;
>> + }
>> + return 0;
>> +}
>> +
>> +#define SDH_PHY_COARSE_FIX_DELAY (SDH_PHY_FIXED_DELAY_MASK / 2)
>> +#define SDH_PHY_FINE_FIX_DELAY (SDH_PHY_COARSE_FIX_DELAY / 4)
>> +
>> +static int xenon_sdh_phy_fix_sampl_delay_adj(struct sdhci_host *host,
>> + struct mmc_card *card)
>> +{
>> + u32 reg;
>> + bool dll_enable = false;
>> + unsigned int min_delay, max_delay, delay;
>> + const bool sampl_edge[] = {
>> + false,
>> + true,
>> + };
>> + int i, nr;
>> + int ret;
>> +
>> + if (host->clock > HIGH_SPEED_MAX_DTR) {
>> + /* Enable DLL when SDCLK is higher than 50MHz */
>> + reg = sdhci_readl(host, SDH_PHY_SLOT_DLL_CTRL);
>> + if (!(reg & SDH_PHY_ENABLE_DLL)) {
>> + reg |= (SDH_PHY_ENABLE_DLL | SDH_PHY_FAST_LOCK_EN);
>> + sdhci_writel(host, reg, SDH_PHY_SLOT_DLL_CTRL);
>> + mdelay(1);
>> +
>> + reg = sdhci_readl(host, SDH_PHY_SLOT_DLL_PHASE_SEL);
>> + reg |= SDH_PHY_DLL_UPDATE_TUNING;
>> + sdhci_writel(host, reg, SDH_PHY_SLOT_DLL_PHASE_SEL);
>> + }
>> + dll_enable = true;
>> + }
>> +
>> + nr = dll_enable ? ARRAY_SIZE(sampl_edge) : 1;
>> + for (i = 0; i < nr; i++) {
>> + for (min_delay = 0; min_delay <= SDH_PHY_FIXED_DELAY_MASK;
>> + min_delay += SDH_PHY_COARSE_FIX_DELAY) {
>> + ret = sdh_phy_do_fix_sampl_delay(host, card, min_delay,
>> + sampl_edge[i]);
>> + if (!ret)
>> + break;
>> + }
>> +
>> + if (ret) {
>> + dev_dbg(mmc_dev(host->mmc),
>> + "Fail to set Fixed Sampling Delay with %s edge\n",
>> + sampl_edge[i] ? "negative" : "positive");
>> + continue;
>> + }
>> +
>> + for (max_delay = min_delay + SDH_PHY_FINE_FIX_DELAY;
>> + max_delay < SDH_PHY_FIXED_DELAY_MASK;
>> + max_delay += SDH_PHY_FINE_FIX_DELAY) {
>> + ret = sdh_phy_do_fix_sampl_delay(host, card, max_delay,
>> + sampl_edge[i]);
>> + if (ret) {
>> + max_delay -= SDH_PHY_FINE_FIX_DELAY;
>> + break;
>> + }
>> + }
>> +
>> + if (!ret) {
>> + delay = SDH_PHY_FIXED_DELAY_MASK;
>> + ret = sdh_phy_do_fix_sampl_delay(host, card, delay,
>> + sampl_edge[i]);
>> + if (!ret)
>> + max_delay = SDH_PHY_FIXED_DELAY_MASK;
>> + }
>> +
>> + if ((max_delay - min_delay) <= SDH_PHY_FIXED_DELAY_WINDOW_MIN) {
>> + dev_info(mmc_dev(host->mmc),
>> + "The window size %d with %s edge is too small\n",
>> + max_delay - min_delay,
>> + sampl_edge[i] ? "negative" : "positive");
>> + continue;
>> + }
>> +
>> + delay = (min_delay + max_delay) / 2;
>> + xenon_sdh_phy_set_fix_sampl_delay(host, delay, sampl_edge[i]);
>> + dev_dbg(mmc_dev(host->mmc), "sampling fix delay = %d with %s edge\n",
>> + delay, sampl_edge[i] ? "negative" : "positive");
>> + return 0;
>> + }
>> + return -EIO;
>> +}
>> +
>> +static const struct xenon_phy_ops sdh_phy_ops = {
>> + .fix_sampl_delay_adj = xenon_sdh_phy_fix_sampl_delay_adj,
>> +};
>> +
>> +static int alloc_sdh_phy(struct sdhci_xenon_priv *priv)
>> +{
>> + priv->phy_params = NULL;
>> + priv->phy_ops = &sdh_phy_ops;
>> + return 0;
>> +}
>> +
>> +/*
>> + * Common functions for all PHYs
>> + */
>> +void xenon_soc_pad_ctrl(struct sdhci_host *host,
>> + unsigned char signal_voltage)
>> +{
>> + struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
>> + struct sdhci_xenon_priv *priv = sdhci_pltfm_priv(pltfm_host);
>> +
>> + if (priv->phy_ops->set_soc_pad)
>> + priv->phy_ops->set_soc_pad(host, signal_voltage);
>> +}
>> +
>> +static int __xenon_emmc_delay_adj_test(struct mmc_card *card)
>> +{
>> + int err;
>> + u8 *ext_csd = NULL;
>> +
>> + err = mmc_get_ext_csd(card, &ext_csd);
>> + kfree(ext_csd);
>> +
>> + return err;
>> +}
>> +
>> +static int __xenon_sdio_delay_adj_test(struct mmc_card *card)
>> +{
>> + struct mmc_command cmd = {0};
>> + int err;
>> +
>> + cmd.opcode = SD_IO_RW_DIRECT;
>> + cmd.flags = MMC_RSP_R5 | MMC_CMD_AC;
>> +
>> + err = mmc_wait_for_cmd(card->host, &cmd, 0);
>> + if (err)
>> + return err;
>> +
>> + if (cmd.resp[0] & R5_ERROR)
>> + return -EIO;
>> + if (cmd.resp[0] & R5_FUNCTION_NUMBER)
>> + return -EINVAL;
>> + if (cmd.resp[0] & R5_OUT_OF_RANGE)
>> + return -ERANGE;
>> + return 0;
>> +}
>> +
>> +static int __xenon_sd_delay_adj_test(struct mmc_card *card)
>> +{
>> + struct mmc_command cmd = {0};
>> + int err;
>> +
>> + cmd.opcode = MMC_SEND_STATUS;
>> + cmd.arg = card->rca << 16;
>> + cmd.flags = MMC_RSP_R1 | MMC_CMD_AC;
>> +
>> + err = mmc_wait_for_cmd(card->host, &cmd, 0);
>> + return err;
>> +}
>> +
>> +static int xenon_delay_adj_test(struct mmc_card *card)
>> +{
>> + WARN_ON(!card);
>> + WARN_ON(!card->host);
>> +
>> + if (mmc_card_mmc(card))
>> + return __xenon_emmc_delay_adj_test(card);
>> + else if (mmc_card_sd(card))
>> + return __xenon_sd_delay_adj_test(card);
>> + else if (mmc_card_sdio(card))
>> + return __xenon_sdio_delay_adj_test(card);
>> + else
>> + return -EINVAL;
>> +}
>> +
>> +static void xenon_phy_set(struct sdhci_host *host, unsigned char timing)
>> +{
>> + struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
>> + struct sdhci_xenon_priv *priv = sdhci_pltfm_priv(pltfm_host);
>> +
>> + if (priv->phy_ops->phy_set)
>> + priv->phy_ops->phy_set(host, timing);
>> +}
>> +
>> +static void xenon_hs400_strobe_delay_adj(struct sdhci_host *host,
>> + struct mmc_card *card)
>> +{
>> + struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
>> + struct sdhci_xenon_priv *priv = sdhci_pltfm_priv(pltfm_host);
>> +
>> + if (WARN_ON(!mmc_card_hs400(card)))
>> + return;
>> +
>> + /* Enable the DLL to automatically adjust HS400 strobe delay.
>> + */
>> + if (priv->phy_ops->strobe_delay_adj)
>> + priv->phy_ops->strobe_delay_adj(host, card);
>> +}
>> +
>> +static int xenon_fix_sampl_delay_adj(struct sdhci_host *host,
>> + struct mmc_card *card)
>> +{
>> + struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
>> + struct sdhci_xenon_priv *priv = sdhci_pltfm_priv(pltfm_host);
>> +
>> + if (priv->phy_ops->fix_sampl_delay_adj)
>> + return priv->phy_ops->fix_sampl_delay_adj(host, card);
>> +
>> + return 0;
>> +}
>> +
>> +/*
>> + * xenon_delay_adj should not be called inside IRQ context,
>> + * either Hard IRQ or Softirq.
>> + */
>> +static int xenon_hs_delay_adj(struct sdhci_host *host,
>> + struct mmc_card *card)
>> +{
>> + struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
>> + struct sdhci_xenon_priv *priv = sdhci_pltfm_priv(pltfm_host);
>> + int ret = 0;
>> +
>> + if (WARN_ON(host->clock <= DEFAULT_SDCLK_FREQ))
>> + return -EINVAL;
>> +
>> + if (mmc_card_hs400(card)) {
>> + xenon_hs400_strobe_delay_adj(host, card);
>> + return 0;
>> + }
>> +
>> + if (((priv->phy_type == EMMC_5_1_PHY) ||
>> + (priv->phy_type == EMMC_5_0_PHY)) &&
>> + (mmc_card_hs200(card) ||
>> + (host->timing == MMC_TIMING_UHS_SDR104))) {
>> + ret = xenon_emmc_phy_config_tuning(host);
>> + if (!ret)
>> + return 0;
>> + }
>> +
>> + ret = xenon_fix_sampl_delay_adj(host, card);
>> + if (ret)
>> + dev_err(mmc_dev(host->mmc), "fails sampling fixed delay adjustment\n");
>> + return ret;
>> +}
>> +
>> +int xenon_phy_adj(struct sdhci_host *host, struct mmc_ios *ios)
>> +{
>> + struct mmc_host *mmc = host->mmc;
>> + struct mmc_card *card;
>> + int ret = 0;
>> + struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
>> + struct sdhci_xenon_priv *priv = sdhci_pltfm_priv(pltfm_host);
>> +
>> + if (!host->clock) {
>> + priv->clock = 0;
>> + return 0;
>> + }
>> +
>> + /*
>> + * The timing, frequency or bus width is changed,
>> + * better to set eMMC PHY based on current setting
>> + * and adjust Xenon SDHC delay.
>> + */
>> + if ((host->clock == priv->clock) &&
>> + (ios->bus_width == priv->bus_width) &&
>> + (ios->timing == priv->timing))
>> + return 0;
>> +
>> + xenon_phy_set(host, ios->timing);
>> +
>> + /* Update the record */
>> + priv->bus_width = ios->bus_width;
>> + /* Temp stage from HS200 to HS400 */
>> + if (((priv->timing == MMC_TIMING_MMC_HS200) &&
>> + (ios->timing == MMC_TIMING_MMC_HS)) ||
>> + ((ios->timing == MMC_TIMING_MMC_HS) &&
>> + (priv->clock > host->clock))) {
>> + priv->timing = ios->timing;
>> + priv->clock = host->clock;
>> + return 0;
>> + }
>> + priv->timing = ios->timing;
>> + priv->clock = host->clock;
>> +
>> + /* Legacy mode is a special case */
>> + if (ios->timing == MMC_TIMING_LEGACY)
>> + return 0;
>> +
>> + card = priv->card_candidate;
>> + if (unlikely(!card)) {
>> + dev_warn(mmc_dev(mmc), "card is not present\n");
>> + return -EINVAL;
>> + }
>> +
>> + if (host->clock > DEFAULT_SDCLK_FREQ)
>> + ret = xenon_hs_delay_adj(host, card);
>> + return ret;
>> +}
>> +
>> +static int add_xenon_phy(struct device_node *np, struct sdhci_host *host,
>> + const char *phy_name)
>> +{
>> + struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
>> + struct sdhci_xenon_priv *priv = sdhci_pltfm_priv(pltfm_host);
>> + int i, ret;
>> +
>> + for (i = 0; i < NR_PHY_TYPES; i++) {
>> + if (!strcmp(phy_name, phy_types[i])) {
>> + priv->phy_type = i;
>> + break;
>> + }
>> + }
>> + if (i == NR_PHY_TYPES) {
>> + dev_err(mmc_dev(host->mmc),
>> + "Unable to determine PHY name %s. Use default eMMC 5.1 PHY\n",
>> + phy_name);
>> + priv->phy_type = EMMC_5_1_PHY;
>> + }
>> +
>> + if (priv->phy_type == SDH_PHY) {
>> + return alloc_sdh_phy(priv);
>> + } else if ((priv->phy_type == EMMC_5_0_PHY) ||
>> + (priv->phy_type == EMMC_5_1_PHY)) {
>> + ret = alloc_emmc_phy(priv);
>> + if (ret)
>> + return ret;
>> + return emmc_phy_parse_param_dt(host, np, priv->phy_params);
>> + }
>> +
>> + return -EINVAL;
>> +}
>> +
>> +int xenon_phy_parse_dt(struct device_node *np, struct sdhci_host *host)
>> +{
>> + const char *phy_type = NULL;
>> +
>> + if (!of_property_read_string(np, "xenon,phy-type", &phy_type))
>> + return add_xenon_phy(np, host, phy_type);
>> +
>> + dev_err(mmc_dev(host->mmc), "Fail to get Xenon PHY type. Use default eMMC 5.1 PHY\n");
>> + return add_xenon_phy(np, host, "emmc 5.1 phy");
>> +}
>> diff --git a/drivers/mmc/host/sdhci-xenon-phy.h b/drivers/mmc/host/sdhci-xenon-phy.h
>> new file mode 100644
>> index 000000000000..4373c71d3b7b
>> --- /dev/null
>> +++ b/drivers/mmc/host/sdhci-xenon-phy.h
>> @@ -0,0 +1,157 @@
>> +/* linux/drivers/mmc/host/sdhci-xenon-phy.h
>> + *
>> + * Author: Hu Ziji <huziji@...vell.com>
>> + * Date: 2016-8-24
>> + *
>> + * Copyright (C) 2016 Marvell, All Rights Reserved.
>> + *
>> + * This program is free software; you can redistribute it and/or modify
>> + * it under the terms of the GNU General Public License as published by
>> + * the Free Software Foundation; either version 2 of the License, or (at
>> + * your option) any later version.
>> + */
>> +#ifndef SDHCI_XENON_PHY_H_
>> +#define SDHCI_XENON_PHY_H_
>> +
>> +#include <linux/types.h>
>> +#include "sdhci.h"
>> +
>> +/* Register base for eMMC PHY 5.0 Version */
>> +#define EMMC_5_0_PHY_REG_BASE 0x0160
>> +/* Register base for eMMC PHY 5.1 Version */
>> +#define EMMC_PHY_REG_BASE 0x0170
>> +
>> +#define EMMC_PHY_TIMING_ADJUST EMMC_PHY_REG_BASE
>> +#define EMMC_5_0_PHY_TIMING_ADJUST EMMC_5_0_PHY_REG_BASE
>> +#define TIMING_ADJUST_SLOW_MODE BIT(29)
>> +#define TIMING_ADJUST_SDIO_MODE BIT(28)
>> +#define OUTPUT_QSN_PHASE_SELECT BIT(17)
>> +#define SAMPL_INV_QSP_PHASE_SELECT BIT(18)
>> +#define SAMPL_INV_QSP_PHASE_SELECT_SHIFT 18
>> +#define PHY_INITIALIZAION BIT(31)
>> +#define WAIT_CYCLE_BEFORE_USING_MASK 0xF
>> +#define WAIT_CYCLE_BEFORE_USING_SHIFT 12
>> +#define FC_SYNC_EN_DURATION_MASK 0xF
>> +#define FC_SYNC_EN_DURATION_SHIFT 8
>> +#define FC_SYNC_RST_EN_DURATION_MASK 0xF
>> +#define FC_SYNC_RST_EN_DURATION_SHIFT 4
>> +#define FC_SYNC_RST_DURATION_MASK 0xF
>> +#define FC_SYNC_RST_DURATION_SHIFT 0
>> +
>> +#define EMMC_PHY_FUNC_CONTROL (EMMC_PHY_REG_BASE + 0x4)
>> +#define EMMC_5_0_PHY_FUNC_CONTROL (EMMC_5_0_PHY_REG_BASE + 0x4)
>> +#define ASYNC_DDRMODE_MASK BIT(23)
>> +#define ASYNC_DDRMODE_SHIFT 23
>> +#define CMD_DDR_MODE BIT(16)
>> +#define DQ_DDR_MODE_SHIFT 8
>> +#define DQ_DDR_MODE_MASK 0xFF
>> +#define DQ_ASYNC_MODE BIT(4)
>> +
>> +#define EMMC_PHY_PAD_CONTROL (EMMC_PHY_REG_BASE + 0x8)
>> +#define EMMC_5_0_PHY_PAD_CONTROL (EMMC_5_0_PHY_REG_BASE + 0x8)
>> +#define REC_EN_SHIFT 24
>> +#define REC_EN_MASK 0xF
>> +#define FC_DQ_RECEN BIT(24)
>> +#define FC_CMD_RECEN BIT(25)
>> +#define FC_QSP_RECEN BIT(26)
>> +#define FC_QSN_RECEN BIT(27)
>> +#define OEN_QSN BIT(28)
>> +#define AUTO_RECEN_CTRL BIT(30)
>> +#define FC_ALL_CMOS_RECEIVER 0xF000
>> +
>> +#define EMMC5_FC_QSP_PD BIT(18)
>> +#define EMMC5_FC_QSP_PU BIT(22)
>> +#define EMMC5_FC_CMD_PD BIT(17)
>> +#define EMMC5_FC_CMD_PU BIT(21)
>> +#define EMMC5_FC_DQ_PD BIT(16)
>> +#define EMMC5_FC_DQ_PU BIT(20)
>> +
>> +#define EMMC_PHY_PAD_CONTROL1 (EMMC_PHY_REG_BASE + 0xC)
>> +#define EMMC5_1_FC_QSP_PD BIT(9)
>> +#define EMMC5_1_FC_QSP_PU BIT(25)
>> +#define EMMC5_1_FC_CMD_PD BIT(8)
>> +#define EMMC5_1_FC_CMD_PU BIT(24)
>> +#define EMMC5_1_FC_DQ_PD 0xFF
>> +#define EMMC5_1_FC_DQ_PU (0xFF << 16)
>> +
>> +#define EMMC_PHY_PAD_CONTROL2 (EMMC_PHY_REG_BASE + 0x10)
>> +#define EMMC_5_0_PHY_PAD_CONTROL2 (EMMC_5_0_PHY_REG_BASE + 0xC)
>> +#define ZNR_MASK 0x1F
>> +#define ZNR_SHIFT 8
>> +#define ZPR_MASK 0x1F
>> +/* Perferred ZNR and ZPR value vary between different boards.
>> + * The specific ZNR and ZPR value should be defined here
>> + * according to board actual timing.
>> + */
>> +#define ZNR_DEF_VALUE 0xF
>> +#define ZPR_DEF_VALUE 0xF
>> +
>> +#define EMMC_PHY_DLL_CONTROL (EMMC_PHY_REG_BASE + 0x14)
>> +#define EMMC_5_0_PHY_DLL_CONTROL (EMMC_5_0_PHY_REG_BASE + 0x10)
>> +#define DLL_ENABLE BIT(31)
>> +#define DLL_UPDATE_STROBE_5_0 BIT(30)
>> +#define DLL_REFCLK_SEL BIT(30)
>> +#define DLL_UPDATE BIT(23)
>> +#define DLL_PHSEL1_SHIFT 24
>> +#define DLL_PHSEL0_SHIFT 16
>> +#define DLL_PHASE_MASK 0x3F
>> +#define DLL_PHASE_90_DEGREE 0x1F
>> +#define DLL_FAST_LOCK BIT(5)
>> +#define DLL_GAIN2X BIT(3)
>> +#define DLL_BYPASS_EN BIT(0)
>> +
>> +#define EMMC_5_0_PHY_LOGIC_TIMING_ADJUST (EMMC_5_0_PHY_REG_BASE + 0x14)
>> +#define EMMC_PHY_LOGIC_TIMING_ADJUST (EMMC_PHY_REG_BASE + 0x18)
>> +
>> +enum sampl_fix_delay_phase {
>> + PHASE_0_DEGREE = 0x0,
>> + PHASE_90_DEGREE = 0x1,
>> + PHASE_180_DEGREE = 0x2,
>> + PHASE_270_DEGREE = 0x3,
>> +};
>> +
>> +#define SDH_PHY_SLOT_DLL_CTRL (0x0138)
>> +#define SDH_PHY_ENABLE_DLL BIT(1)
>> +#define SDH_PHY_FAST_LOCK_EN BIT(5)
>> +
>> +#define SDH_PHY_SLOT_DLL_PHASE_SEL (0x013C)
>> +#define SDH_PHY_DLL_UPDATE_TUNING BIT(15)
>> +
>> +enum soc_pad_ctrl_type {
>> + SOC_PAD_SD,
>> + SOC_PAD_FIXED_1_8V,
>> +};
>> +
>> +/*
>> + * List offset of PHY registers and some special register values
>> + * in eMMC PHY 5.0 or eMMC PHY 5.1
>> + */
>> +struct xenon_emmc_phy_regs {
>> + /* Offset of Timing Adjust register */
>> + u16 timing_adj;
>> + /* Offset of Func Control register */
>> + u16 func_ctrl;
>> + /* Offset of Pad Control register */
>> + u16 pad_ctrl;
>> + /* Offset of Pad Control register */
>> + u16 pad_ctrl2;
>> + /* Offset of DLL Control register */
>> + u16 dll_ctrl;
>> + /* Offset of Logic Timing Adjust register */
>> + u16 logic_timing_adj;
>> + /* Max value of eMMC Fixed Sampling Delay */
>> + u32 delay_mask;
>> + /* DLL Update Enable bit */
>> + u32 dll_update;
>> +};
>> +
>> +struct xenon_phy_ops {
>> + void (*strobe_delay_adj)(struct sdhci_host *host,
>> + struct mmc_card *card);
>> + int (*fix_sampl_delay_adj)(struct sdhci_host *host,
>> + struct mmc_card *card);
>> + void (*phy_set)(struct sdhci_host *host, unsigned char timing);
>> + void (*set_soc_pad)(struct sdhci_host *host,
>> + unsigned char signal_voltage);
>> +};
>> +#endif
>> diff --git a/drivers/mmc/host/sdhci-xenon.c b/drivers/mmc/host/sdhci-xenon.c
>> index 03ba183494d3..4d7d871544fc 100644
>> --- a/drivers/mmc/host/sdhci-xenon.c
>> +++ b/drivers/mmc/host/sdhci-xenon.c
>> @@ -224,6 +224,7 @@ static void xenon_set_ios(struct mmc_host *mmc, struct mmc_ios *ios)
>> spin_unlock_irqrestore(&host->lock, flags);
>>
>> sdhci_set_ios(mmc, ios);
>> + xenon_phy_adj(host, ios);
>>
>> if (host->clock > DEFAULT_SDCLK_FREQ) {
>> spin_lock_irqsave(&host->lock, flags);
>> @@ -309,6 +310,8 @@ static int xenon_start_signal_voltage_switch(struct mmc_host *mmc,
>> */
>> enable_xenon_internal_clk(host);
>>
>> + xenon_soc_pad_ctrl(host, ios->signal_voltage);
>> +
>> if (priv->card_candidate) {
>> if (mmc_card_mmc(priv->card_candidate))
>> return xenon_emmc_signal_voltage_switch(mmc, ios);
>> @@ -453,6 +456,7 @@ static int xenon_probe_dt(struct platform_device *pdev)
>> sdhci_writel(host, reg, SDHC_SYS_EXT_OP_CTRL);
>> }
>>
>> + err = xenon_phy_parse_dt(np, host);
>> return err;
>> }
>>
>> diff --git a/drivers/mmc/host/sdhci-xenon.h b/drivers/mmc/host/sdhci-xenon.h
>> index c2370493fbe8..06e5261a563c 100644
>> --- a/drivers/mmc/host/sdhci-xenon.h
>> +++ b/drivers/mmc/host/sdhci-xenon.h
>> @@ -15,6 +15,7 @@
>> #include <linux/mmc/card.h>
>> #include <linux/of.h>
>> #include "sdhci.h"
>> +#include "sdhci-xenon-phy.h"
>>
>> /* Register Offset of SD Host Controller SOCP self-defined register */
>> #define SDHC_SYS_CFG_INFO 0x0104
>> @@ -76,6 +77,7 @@
>> #define MMC_TIMING_FAKE 0xFF
>>
>> #define DEFAULT_SDCLK_FREQ (400000)
>> +#define LOWEST_SDCLK_FREQ (100000)
>>
>> /* Xenon specific Mode Select value */
>> #define XENON_SDHCI_CTRL_HS200 0x5
>> @@ -97,6 +99,15 @@ struct sdhci_xenon_priv {
>> /* Slot idx */
>> u8 slot_idx;
>>
>> + int phy_type;
>> + /*
>> + * Contains board-specific PHY parameters
>> + * passed from device tree.
>> + */
>> + void *phy_params;
>> + const struct xenon_phy_ops *phy_ops;
>> + struct xenon_emmc_phy_regs *emmc_phy_regs;
>> +
>> /*
>> * When initializing card, Xenon has to determine card type and
>> * adjust Sampling Fixed delay.
>> @@ -131,4 +142,10 @@ static inline int enable_xenon_internal_clk(struct sdhci_host *host)
>>
>> return 0;
>> }
>> +
>> +int xenon_phy_adj(struct sdhci_host *host, struct mmc_ios *ios);
>> +int xenon_phy_parse_dt(struct device_node *np,
>> + struct sdhci_host *host);
>> +void xenon_soc_pad_ctrl(struct sdhci_host *host,
>> + unsigned char signal_voltage);
>> #endif
>>
>
>
Powered by blists - more mailing lists