| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-Id: <20161017195417.48259-4-jarod@redhat.com>
Date: Mon, 17 Oct 2016 15:54:05 -0400
From: Jarod Wilson <jarod@...hat.com>
To: linux-kernel@...r.kernel.org
Cc: Jarod Wilson <jarod@...hat.com>, netdev@...r.kernel.org,
intel-wired-lan@...ts.osuosl.org,
Jeff Kirsher <jeffrey.t.kirsher@...el.com>
Subject: [PATCH net-next 03/15] ethernet/intel: use core min/max MTU checking
e100: min_mtu 68, max_mtu 1500
- remove e100_change_mtu entirely, is identical to old eth_change_mtu,
and no longer serves a purpose. No need to set min_mtu or max_mtu
explicitly, as ether_setup() will already set them to 68 and 1500.
e1000: min_mtu 46, max_mtu 16110
e1000e: min_mtu 68, max_mtu varies based on adapter
fm10k: min_mtu 68, max_mtu 15342
- remove fm10k_change_mtu entirely, does nothing now
i40e: min_mtu 68, max_mtu 9706
i40evf: min_mtu 68, max_mtu 9706
igb: min_mtu 68, max_mtu 9216
- There are two different "max" frame sizes claimed and both checked in
the driver, the larger value wasn't relevant though, so I've set max_mtu
to the smaller of the two values here to retain identical behavior.
igbvf: min_mtu 68, max_mtu 9216
- Same issue as igb duplicated
ixgb: min_mtu 68, max_mtu 16114
- Also remove pointless old == new check, as that's done in dev_set_mtu
ixgbe: min_mtu 68, max_mtu 9710
ixgbevf: min_mtu 68, max_mtu dependent on hardware/firmware
- Some hw can only handle up to max_mtu 1504 on a vf, others 9710
CC: netdev@...r.kernel.org
CC: intel-wired-lan@...ts.osuosl.org
CC: Jeff Kirsher <jeffrey.t.kirsher@...el.com>
Signed-off-by: Jarod Wilson <jarod@...hat.com>
---
drivers/net/ethernet/intel/e100.c | 9 -------
drivers/net/ethernet/intel/e1000/e1000_main.c | 12 ++++-----
drivers/net/ethernet/intel/e1000e/netdev.c | 14 +++++-----
drivers/net/ethernet/intel/fm10k/fm10k_netdev.c | 15 +++--------
drivers/net/ethernet/intel/i40e/i40e_main.c | 10 +++----
drivers/net/ethernet/intel/i40evf/i40evf_main.c | 8 +++---
drivers/net/ethernet/intel/igb/e1000_defines.h | 3 ++-
drivers/net/ethernet/intel/igb/igb_main.c | 15 +++--------
drivers/net/ethernet/intel/igbvf/defines.h | 3 ++-
drivers/net/ethernet/intel/igbvf/netdev.c | 14 +++-------
drivers/net/ethernet/intel/ixgb/ixgb_main.c | 16 +++--------
drivers/net/ethernet/intel/ixgbe/ixgbe_main.c | 11 ++++----
drivers/net/ethernet/intel/ixgbevf/ixgbevf_main.c | 33 ++++++++++++-----------
13 files changed, 62 insertions(+), 101 deletions(-)
diff --git a/drivers/net/ethernet/intel/e100.c b/drivers/net/ethernet/intel/e100.c
index 068789e..25c6dfd 100644
--- a/drivers/net/ethernet/intel/e100.c
+++ b/drivers/net/ethernet/intel/e100.c
@@ -2286,14 +2286,6 @@ static int e100_set_mac_address(struct net_device *netdev, void *p)
return 0;
}
-static int e100_change_mtu(struct net_device *netdev, int new_mtu)
-{
- if (new_mtu < ETH_ZLEN || new_mtu > ETH_DATA_LEN)
- return -EINVAL;
- netdev->mtu = new_mtu;
- return 0;
-}
-
static int e100_asf(struct nic *nic)
{
/* ASF can be enabled from eeprom */
@@ -2834,7 +2826,6 @@ static const struct net_device_ops e100_netdev_ops = {
.ndo_validate_addr = eth_validate_addr,
.ndo_set_rx_mode = e100_set_multicast_list,
.ndo_set_mac_address = e100_set_mac_address,
- .ndo_change_mtu = e100_change_mtu,
.ndo_do_ioctl = e100_do_ioctl,
.ndo_tx_timeout = e100_tx_timeout,
#ifdef CONFIG_NET_POLL_CONTROLLER
diff --git a/drivers/net/ethernet/intel/e1000/e1000_main.c b/drivers/net/ethernet/intel/e1000/e1000_main.c
index f42129d..33076fa 100644
--- a/drivers/net/ethernet/intel/e1000/e1000_main.c
+++ b/drivers/net/ethernet/intel/e1000/e1000_main.c
@@ -1085,6 +1085,10 @@ static int e1000_probe(struct pci_dev *pdev, const struct pci_device_id *ent)
hw->subsystem_vendor_id != PCI_VENDOR_ID_VMWARE)
netdev->priv_flags |= IFF_UNICAST_FLT;
+ /* MTU range: 46 - 16110 */
+ netdev->min_mtu = ETH_ZLEN - ETH_HLEN;
+ netdev->max_mtu = MAX_JUMBO_FRAME_SIZE - (ETH_HLEN + ETH_FCS_LEN);
+
adapter->en_mng_pt = e1000_enable_mng_pass_thru(hw);
/* initialize eeprom parameters */
@@ -3549,13 +3553,7 @@ static int e1000_change_mtu(struct net_device *netdev, int new_mtu)
{
struct e1000_adapter *adapter = netdev_priv(netdev);
struct e1000_hw *hw = &adapter->hw;
- int max_frame = new_mtu + ENET_HEADER_SIZE + ETHERNET_FCS_SIZE;
-
- if ((max_frame < MINIMUM_ETHERNET_FRAME_SIZE) ||
- (max_frame > MAX_JUMBO_FRAME_SIZE)) {
- e_err(probe, "Invalid MTU setting\n");
- return -EINVAL;
- }
+ int max_frame = new_mtu + ETH_HLEN + ETH_FCS_LEN;
/* Adapter-specific max frame size limits. */
switch (hw->mac_type) {
diff --git a/drivers/net/ethernet/intel/e1000e/netdev.c b/drivers/net/ethernet/intel/e1000e/netdev.c
index 7017281..8759d92 100644
--- a/drivers/net/ethernet/intel/e1000e/netdev.c
+++ b/drivers/net/ethernet/intel/e1000e/netdev.c
@@ -5974,19 +5974,12 @@ static int e1000_change_mtu(struct net_device *netdev, int new_mtu)
int max_frame = new_mtu + VLAN_ETH_HLEN + ETH_FCS_LEN;
/* Jumbo frame support */
- if ((max_frame > (VLAN_ETH_FRAME_LEN + ETH_FCS_LEN)) &&
+ if ((new_mtu > ETH_DATA_LEN) &&
!(adapter->flags & FLAG_HAS_JUMBO_FRAMES)) {
e_err("Jumbo Frames not supported.\n");
return -EINVAL;
}
- /* Supported frame sizes */
- if ((new_mtu < (VLAN_ETH_ZLEN + ETH_FCS_LEN)) ||
- (max_frame > adapter->max_hw_frame_size)) {
- e_err("Unsupported MTU setting\n");
- return -EINVAL;
- }
-
/* Jumbo frame workaround on 82579 and newer requires CRC be stripped */
if ((adapter->hw.mac.type >= e1000_pch2lan) &&
!(adapter->flags2 & FLAG2_CRC_STRIPPING) &&
@@ -7187,6 +7180,11 @@ static int e1000_probe(struct pci_dev *pdev, const struct pci_device_id *ent)
netdev->vlan_features |= NETIF_F_HIGHDMA;
}
+ /* MTU range: 68 - max_hw_frame_size */
+ netdev->min_mtu = ETH_MIN_MTU;
+ netdev->max_mtu = adapter->max_hw_frame_size -
+ (VLAN_ETH_HLEN + ETH_FCS_LEN);
+
if (e1000e_enable_mng_pass_thru(&adapter->hw))
adapter->flags |= FLAG_MNG_PT_ENABLED;
diff --git a/drivers/net/ethernet/intel/fm10k/fm10k_netdev.c b/drivers/net/ethernet/intel/fm10k/fm10k_netdev.c
index 0562938..bc5ef6e 100644
--- a/drivers/net/ethernet/intel/fm10k/fm10k_netdev.c
+++ b/drivers/net/ethernet/intel/fm10k/fm10k_netdev.c
@@ -706,16 +706,6 @@ static netdev_tx_t fm10k_xmit_frame(struct sk_buff *skb, struct net_device *dev)
return err;
}
-static int fm10k_change_mtu(struct net_device *dev, int new_mtu)
-{
- if (new_mtu < 68 || new_mtu > FM10K_MAX_JUMBO_FRAME_SIZE)
- return -EINVAL;
-
- dev->mtu = new_mtu;
-
- return 0;
-}
-
/**
* fm10k_tx_timeout - Respond to a Tx Hang
* @netdev: network interface device structure
@@ -1405,7 +1395,6 @@ static const struct net_device_ops fm10k_netdev_ops = {
.ndo_validate_addr = eth_validate_addr,
.ndo_start_xmit = fm10k_xmit_frame,
.ndo_set_mac_address = fm10k_set_mac,
- .ndo_change_mtu = fm10k_change_mtu,
.ndo_tx_timeout = fm10k_tx_timeout,
.ndo_vlan_rx_add_vid = fm10k_vlan_rx_add_vid,
.ndo_vlan_rx_kill_vid = fm10k_vlan_rx_kill_vid,
@@ -1490,5 +1479,9 @@ struct net_device *fm10k_alloc_netdev(const struct fm10k_info *info)
dev->hw_features |= hw_features;
+ /* MTU range: 68 - 15342 */
+ dev->min_mtu = ETH_MIN_MTU;
+ dev->max_mtu = FM10K_MAX_JUMBO_FRAME_SIZE;
+
return dev;
}
diff --git a/drivers/net/ethernet/intel/i40e/i40e_main.c b/drivers/net/ethernet/intel/i40e/i40e_main.c
index ac1faee..83edbe8 100644
--- a/drivers/net/ethernet/intel/i40e/i40e_main.c
+++ b/drivers/net/ethernet/intel/i40e/i40e_main.c
@@ -2239,13 +2239,8 @@ static void i40e_sync_filters_subtask(struct i40e_pf *pf)
static int i40e_change_mtu(struct net_device *netdev, int new_mtu)
{
struct i40e_netdev_priv *np = netdev_priv(netdev);
- int max_frame = new_mtu + ETH_HLEN + ETH_FCS_LEN + VLAN_HLEN;
struct i40e_vsi *vsi = np->vsi;
- /* MTU < 68 is an error and causes problems on some kernels */
- if ((new_mtu < 68) || (max_frame > I40E_MAX_RXBUFFER))
- return -EINVAL;
-
netdev_info(netdev, "changing MTU from %d to %d\n",
netdev->mtu, new_mtu);
netdev->mtu = new_mtu;
@@ -9220,6 +9215,11 @@ static int i40e_config_netdev(struct i40e_vsi *vsi)
i40e_fcoe_config_netdev(netdev, vsi);
#endif
+ /* MTU range: 68 - 9706 */
+ netdev->min_mtu = ETH_MIN_MTU;
+ netdev->max_mtu = I40E_MAX_RXBUFFER -
+ (ETH_HLEN + ETH_FCS_LEN + VLAN_HLEN);
+
return 0;
}
diff --git a/drivers/net/ethernet/intel/i40evf/i40evf_main.c b/drivers/net/ethernet/intel/i40evf/i40evf_main.c
index 1437281..777eb29 100644
--- a/drivers/net/ethernet/intel/i40evf/i40evf_main.c
+++ b/drivers/net/ethernet/intel/i40evf/i40evf_main.c
@@ -2133,10 +2133,6 @@ static struct net_device_stats *i40evf_get_stats(struct net_device *netdev)
static int i40evf_change_mtu(struct net_device *netdev, int new_mtu)
{
struct i40evf_adapter *adapter = netdev_priv(netdev);
- int max_frame = new_mtu + ETH_HLEN + ETH_FCS_LEN;
-
- if ((new_mtu < 68) || (max_frame > I40E_MAX_RXBUFFER))
- return -EINVAL;
netdev->mtu = new_mtu;
adapter->flags |= I40EVF_FLAG_RESET_NEEDED;
@@ -2424,6 +2420,10 @@ static void i40evf_init_task(struct work_struct *work)
i40evf_set_ethtool_ops(netdev);
netdev->watchdog_timeo = 5 * HZ;
+ /* MTU range: 68 - 9710 */
+ netdev->min_mtu = ETH_MIN_MTU;
+ netdev->max_mtu = I40E_MAX_RXBUFFER - (ETH_HLEN + ETH_FCS_LEN);
+
if (!is_valid_ether_addr(adapter->hw.mac.addr)) {
dev_info(&pdev->dev, "Invalid MAC address %pM, using random\n",
adapter->hw.mac.addr);
diff --git a/drivers/net/ethernet/intel/igb/e1000_defines.h b/drivers/net/ethernet/intel/igb/e1000_defines.h
index 2688180..8aee314 100644
--- a/drivers/net/ethernet/intel/igb/e1000_defines.h
+++ b/drivers/net/ethernet/intel/igb/e1000_defines.h
@@ -357,7 +357,8 @@
#define ETHERNET_IEEE_VLAN_TYPE 0x8100 /* 802.3ac packet */
/* As per the EAS the maximum supported size is 9.5KB (9728 bytes) */
-#define MAX_JUMBO_FRAME_SIZE 0x2600
+#define MAX_JUMBO_FRAME_SIZE 0x2600
+#define MAX_STD_JUMBO_FRAME_SIZE 9216
/* PBA constants */
#define E1000_PBA_34K 0x0022
diff --git a/drivers/net/ethernet/intel/igb/igb_main.c b/drivers/net/ethernet/intel/igb/igb_main.c
index edc9a6a..4feca69 100644
--- a/drivers/net/ethernet/intel/igb/igb_main.c
+++ b/drivers/net/ethernet/intel/igb/igb_main.c
@@ -2468,6 +2468,10 @@ static int igb_probe(struct pci_dev *pdev, const struct pci_device_id *ent)
netdev->priv_flags |= IFF_UNICAST_FLT;
+ /* MTU range: 68 - 9216 */
+ netdev->min_mtu = ETH_MIN_MTU;
+ netdev->max_mtu = MAX_STD_JUMBO_FRAME_SIZE;
+
adapter->en_mng_pt = igb_enable_mng_pass_thru(hw);
/* before reading the NVM, reset the controller to put the device in a
@@ -5408,17 +5412,6 @@ static int igb_change_mtu(struct net_device *netdev, int new_mtu)
struct pci_dev *pdev = adapter->pdev;
int max_frame = new_mtu + ETH_HLEN + ETH_FCS_LEN + VLAN_HLEN;
- if ((new_mtu < 68) || (max_frame > MAX_JUMBO_FRAME_SIZE)) {
- dev_err(&pdev->dev, "Invalid MTU setting\n");
- return -EINVAL;
- }
-
-#define MAX_STD_JUMBO_FRAME_SIZE 9238
- if (max_frame > MAX_STD_JUMBO_FRAME_SIZE) {
- dev_err(&pdev->dev, "MTU > 9216 not supported.\n");
- return -EINVAL;
- }
-
/* adjust max frame to be at least the size of a standard frame */
if (max_frame < (ETH_FRAME_LEN + ETH_FCS_LEN))
max_frame = ETH_FRAME_LEN + ETH_FCS_LEN;
diff --git a/drivers/net/ethernet/intel/igbvf/defines.h b/drivers/net/ethernet/intel/igbvf/defines.h
index ee1ef08..f1789d1 100644
--- a/drivers/net/ethernet/intel/igbvf/defines.h
+++ b/drivers/net/ethernet/intel/igbvf/defines.h
@@ -85,7 +85,8 @@
#define E1000_TXD_CMD_DEXT 0x20000000 /* Desc extension (0 = legacy) */
#define E1000_TXD_STAT_DD 0x00000001 /* Desc Done */
-#define MAX_JUMBO_FRAME_SIZE 0x3F00
+#define MAX_JUMBO_FRAME_SIZE 0x3F00
+#define MAX_STD_JUMBO_FRAME_SIZE 9216
/* 802.1q VLAN Packet Size */
#define VLAN_TAG_SIZE 4 /* 802.3ac tag (not DMA'd) */
diff --git a/drivers/net/ethernet/intel/igbvf/netdev.c b/drivers/net/ethernet/intel/igbvf/netdev.c
index 12bb877..810fcf7 100644
--- a/drivers/net/ethernet/intel/igbvf/netdev.c
+++ b/drivers/net/ethernet/intel/igbvf/netdev.c
@@ -2356,16 +2356,6 @@ static int igbvf_change_mtu(struct net_device *netdev, int new_mtu)
struct igbvf_adapter *adapter = netdev_priv(netdev);
int max_frame = new_mtu + ETH_HLEN + ETH_FCS_LEN;
- if (new_mtu < 68 || new_mtu > INT_MAX - ETH_HLEN - ETH_FCS_LEN ||
- max_frame > MAX_JUMBO_FRAME_SIZE)
- return -EINVAL;
-
-#define MAX_STD_JUMBO_FRAME_SIZE 9234
- if (max_frame > MAX_STD_JUMBO_FRAME_SIZE) {
- dev_err(&adapter->pdev->dev, "MTU > 9216 not supported.\n");
- return -EINVAL;
- }
-
while (test_and_set_bit(__IGBVF_RESETTING, &adapter->state))
usleep_range(1000, 2000);
/* igbvf_down has a dependency on max_frame_size */
@@ -2786,6 +2776,10 @@ static int igbvf_probe(struct pci_dev *pdev, const struct pci_device_id *ent)
NETIF_F_HW_VLAN_CTAG_RX |
NETIF_F_HW_VLAN_CTAG_TX;
+ /* MTU range: 68 - 9216 */
+ netdev->min_mtu = ETH_MIN_MTU;
+ netdev->max_mtu = MAX_STD_JUMBO_FRAME_SIZE;
+
/*reset the controller to put the device in a known good state */
err = hw->mac.ops.reset_hw(hw);
if (err) {
diff --git a/drivers/net/ethernet/intel/ixgb/ixgb_main.c b/drivers/net/ethernet/intel/ixgb/ixgb_main.c
index 31f9145..5826b1d 100644
--- a/drivers/net/ethernet/intel/ixgb/ixgb_main.c
+++ b/drivers/net/ethernet/intel/ixgb/ixgb_main.c
@@ -487,6 +487,10 @@ ixgb_probe(struct pci_dev *pdev, const struct pci_device_id *ent)
netdev->vlan_features |= NETIF_F_HIGHDMA;
}
+ /* MTU range: 68 - 16114 */
+ netdev->min_mtu = ETH_MIN_MTU;
+ netdev->max_mtu = IXGB_MAX_JUMBO_FRAME_SIZE - ETH_HLEN;
+
/* make sure the EEPROM is good */
if (!ixgb_validate_eeprom_checksum(&adapter->hw)) {
@@ -1619,18 +1623,6 @@ ixgb_change_mtu(struct net_device *netdev, int new_mtu)
{
struct ixgb_adapter *adapter = netdev_priv(netdev);
int max_frame = new_mtu + ENET_HEADER_SIZE + ENET_FCS_LENGTH;
- int old_max_frame = netdev->mtu + ENET_HEADER_SIZE + ENET_FCS_LENGTH;
-
- /* MTU < 68 is an error for IPv4 traffic, just don't allow it */
- if ((new_mtu < 68) ||
- (max_frame > IXGB_MAX_JUMBO_FRAME_SIZE + ENET_FCS_LENGTH)) {
- netif_err(adapter, probe, adapter->netdev,
- "Invalid MTU setting %d\n", new_mtu);
- return -EINVAL;
- }
-
- if (old_max_frame == max_frame)
- return 0;
if (netif_running(netdev))
ixgb_down(adapter, true);
diff --git a/drivers/net/ethernet/intel/ixgbe/ixgbe_main.c b/drivers/net/ethernet/intel/ixgbe/ixgbe_main.c
index 784b0b9..7dfde20 100644
--- a/drivers/net/ethernet/intel/ixgbe/ixgbe_main.c
+++ b/drivers/net/ethernet/intel/ixgbe/ixgbe_main.c
@@ -6049,11 +6049,6 @@ static void ixgbe_free_all_rx_resources(struct ixgbe_adapter *adapter)
static int ixgbe_change_mtu(struct net_device *netdev, int new_mtu)
{
struct ixgbe_adapter *adapter = netdev_priv(netdev);
- int max_frame = new_mtu + ETH_HLEN + ETH_FCS_LEN;
-
- /* MTU < 68 is an error and causes problems on some kernels */
- if ((new_mtu < 68) || (max_frame > IXGBE_MAX_JUMBO_FRAME_SIZE))
- return -EINVAL;
/*
* For 82599EB we cannot allow legacy VFs to enable their receive
@@ -6062,7 +6057,7 @@ static int ixgbe_change_mtu(struct net_device *netdev, int new_mtu)
*/
if ((adapter->flags & IXGBE_FLAG_SRIOV_ENABLED) &&
(adapter->hw.mac.type == ixgbe_mac_82599EB) &&
- (max_frame > (ETH_FRAME_LEN + ETH_FCS_LEN)))
+ (new_mtu > ETH_DATA_LEN))
e_warn(probe, "Setting MTU > 1500 will disable legacy VFs\n");
e_info(probe, "changing MTU from %d to %d\n", netdev->mtu, new_mtu);
@@ -9608,6 +9603,10 @@ static int ixgbe_probe(struct pci_dev *pdev, const struct pci_device_id *ent)
netdev->priv_flags |= IFF_UNICAST_FLT;
netdev->priv_flags |= IFF_SUPP_NOFCS;
+ /* MTU range: 68 - 9710 */
+ netdev->min_mtu = ETH_MIN_MTU;
+ netdev->max_mtu = IXGBE_MAX_JUMBO_FRAME_SIZE - (ETH_HLEN + ETH_FCS_LEN);
+
#ifdef CONFIG_IXGBE_DCB
if (adapter->flags & IXGBE_FLAG_DCB_CAPABLE)
netdev->dcbnl_ops = &dcbnl_ops;
diff --git a/drivers/net/ethernet/intel/ixgbevf/ixgbevf_main.c b/drivers/net/ethernet/intel/ixgbevf/ixgbevf_main.c
index 7eaac32..d2775f0 100644
--- a/drivers/net/ethernet/intel/ixgbevf/ixgbevf_main.c
+++ b/drivers/net/ethernet/intel/ixgbevf/ixgbevf_main.c
@@ -3742,24 +3742,8 @@ static int ixgbevf_change_mtu(struct net_device *netdev, int new_mtu)
struct ixgbevf_adapter *adapter = netdev_priv(netdev);
struct ixgbe_hw *hw = &adapter->hw;
int max_frame = new_mtu + ETH_HLEN + ETH_FCS_LEN;
- int max_possible_frame = MAXIMUM_ETHERNET_VLAN_SIZE;
int ret;
- switch (adapter->hw.api_version) {
- case ixgbe_mbox_api_11:
- case ixgbe_mbox_api_12:
- max_possible_frame = IXGBE_MAX_JUMBO_FRAME_SIZE;
- break;
- default:
- if (adapter->hw.mac.type != ixgbe_mac_82599_vf)
- max_possible_frame = IXGBE_MAX_JUMBO_FRAME_SIZE;
- break;
- }
-
- /* MTU < 68 is an error and causes problems on some kernels */
- if ((new_mtu < 68) || (max_frame > max_possible_frame))
- return -EINVAL;
-
spin_lock_bh(&adapter->mbx_lock);
/* notify the PF of our intent to use this size of frame */
ret = hw->mac.ops.set_rlpml(hw, max_frame);
@@ -4104,6 +4088,23 @@ static int ixgbevf_probe(struct pci_dev *pdev, const struct pci_device_id *ent)
netdev->priv_flags |= IFF_UNICAST_FLT;
+ /* MTU range: 68 - 1504 or 9710 */
+ netdev->min_mtu = ETH_MIN_MTU;
+ switch (adapter->hw.api_version) {
+ case ixgbe_mbox_api_11:
+ case ixgbe_mbox_api_12:
+ netdev->max_mtu = IXGBE_MAX_JUMBO_FRAME_SIZE -
+ (ETH_HLEN + ETH_FCS_LEN);
+ break;
+ default:
+ if (adapter->hw.mac.type != ixgbe_mac_82599_vf)
+ netdev->max_mtu = IXGBE_MAX_JUMBO_FRAME_SIZE -
+ (ETH_HLEN + ETH_FCS_LEN);
+ else
+ netdev->max_mtu = ETH_DATA_LEN + ETH_FCS_LEN;
+ break;
+ }
+
if (IXGBE_REMOVED(hw->hw_addr)) {
err = -EIO;
goto err_sw_init;
--
2.10.0
Powered by blists - more mailing lists