| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-Id: <1477040998-2016-1-git-send-email-narmstrong@baylibre.com>
Date: Fri, 21 Oct 2016 11:09:58 +0200
From: Neil Armstrong <narmstrong@...libre.com>
To: linus.walleij@...aro.org, peda@...ntia.se
Cc: Neil Armstrong <narmstrong@...libre.com>,
linux-kernel@...r.kernel.org, linux-gpio@...r.kernel.org,
devicetree@...r.kernel.org, stigge@...com.de,
vladimir_zapolskiy@...tor.com, andrew.smirnov@...il.com
Subject: [PATCH v3] pinctrl: Add SX150X GPIO Extender Pinctrl Driver
Since the I2C sx150x GPIO expander driver uses platform_data to manage
the pins configurations, rewrite the driver as a pinctrl driver using
pinconf to get/set pin configurations from DT or debugfs.
The pinctrl driver is functionnally equivalent as the gpio-only driver
and can use DT for pinconf. The platform_data confirmation is dropped.
This patchset removed the gpio-only driver and selects the Pinctrl driver
config instead. This patchset also migrates the gpio dt-bindings to pinctrl
and add the pinctrl optional properties.
The driver was tested with a SX1509 device on a BeagleBone black with
interrupt support and on an X86_64 machine over an I2C to USB converter.
Signed-off-by: Neil Armstrong <narmstrong@...libre.com>
---
This is a fixed version that builds and runs on non-OF platforms and on
arm based OF. The GPIO version is removed and the bindings are also moved
to the pinctrl bindings.
Changes since v2 at http://lkml.kernel.org/r/1474991325-1754-1-git-send-email-narmstrong@baylibre.com:
- rebased on v4.9-rc1
- removed MODULE_DEVICE_TABLE as in upstream bb411e771b0e [1]
Changes since v1 at http://lkml.kernel.org/r/1473166599-29266-1-git-send-email-narmstrong@baylibre.com:
- Fix Kconfig descriptions on pinctrl and gpio
- Fix Kconfig dependency
- Remove oscio support for non-789 devices
- correct typo in dt bindings
- remove probe reset for non-789 devices
Changes since RFC at http://lkml.kernel.org/r/1472130692-14404-1-git-send-email-narmstrong@baylibre.com:
- Put #ifdef CONFIG_OF/CONFIG_OF_GPIO to remove OF code for non-of platforms
- No more rely on OF_GPIO config
- Moved and enhanced bindings to pinctrl bindings
- Removed gpio-sx150x.c
- Temporary select PINCTRL_SX150X when GPIO_SX150X
- Temporary mark GPIO_SX150X as deprecated
[1] gpio: sx150x: fix implicit assumption module.h is present
.../gpio-sx150x.txt => pinctrl/pinctrl-sx150x.txt} | 46 +-
drivers/gpio/Kconfig | 13 +-
drivers/gpio/Makefile | 1 -
drivers/pinctrl/Kconfig | 14 +
drivers/pinctrl/Makefile | 1 +
.../gpio-sx150x.c => pinctrl/pinctrl-sx150x.c} | 1174 ++++++++++++--------
6 files changed, 779 insertions(+), 470 deletions(-)
rename Documentation/devicetree/bindings/{gpio/gpio-sx150x.txt => pinctrl/pinctrl-sx150x.txt} (40%)
rename drivers/{gpio/gpio-sx150x.c => pinctrl/pinctrl-sx150x.c} (23%)
diff --git a/Documentation/devicetree/bindings/gpio/gpio-sx150x.txt b/Documentation/devicetree/bindings/pinctrl/pinctrl-sx150x.txt
similarity index 40%
rename from Documentation/devicetree/bindings/gpio/gpio-sx150x.txt
rename to Documentation/devicetree/bindings/pinctrl/pinctrl-sx150x.txt
index c809acb..c293c8a 100644
--- a/Documentation/devicetree/bindings/gpio/gpio-sx150x.txt
+++ b/Documentation/devicetree/bindings/pinctrl/pinctrl-sx150x.txt
@@ -1,34 +1,54 @@
SEMTECH SX150x GPIO expander bindings
+Please refer to pinctrl-bindings.txt, ../gpio/gpio.txt, and
+../interrupt-controller/interrupts.txt for generic information regarding
+pin controller, GPIO, and interrupt bindings.
Required properties:
-
-- compatible: should be "semtech,sx1506q",
+- compatible: should be one of :
+ "semtech,sx1506q",
"semtech,sx1508q",
"semtech,sx1509q",
"semtech,sx1502q".
- reg: The I2C slave address for this device.
-- interrupt-parent: phandle of the parent interrupt controller.
-
-- interrupts: Interrupt specifier for the controllers interrupt.
-
- #gpio-cells: Should be 2. The first cell is the GPIO number and the
second cell is used to specify optional parameters:
bit 0: polarity (0: normal, 1: inverted)
- gpio-controller: Marks the device as a GPIO controller.
+Optional properties :
+- interrupt-parent: phandle of the parent interrupt controller.
+
+- interrupts: Interrupt specifier for the controllers interrupt.
+
- interrupt-controller: Marks the device as a interrupt controller.
+- semtech,probe-reset: Will trigger a reset of the GPIO expander on probe,
+ only for sx1508q and sx1509q
+
The GPIO expander can optionally be used as an interrupt controller, in
-which case it uses the default two cell specifier as described in
-Documentation/devicetree/bindings/interrupt-controller/interrupts.txt.
+which case it uses the default two cell specifier.
+
+Required properties for pin configuration sub-nodes:
+ - pins: List of pins to which the configuration applies.
+
+Optional properties for pin configuration sub-nodes:
+----------------------------------------------------
+ - bias-disable: disable any pin bias, except the OSCIO pin
+ - bias-pull-up: pull up the pin, except the OSCIO pin
+ - bias-pull-down: pull down the pin, except the OSCIO pin
+ - bias-pull-pin-default: use pin-default pull state, except the OSCIO pin
+ - drive-push-pull: drive actively high and low
+ - drive-open-drain: drive with open drain only for sx1508q and sx1509q and except the OSCIO pin
+ - output-low: set the pin to output mode with low level
+ - output-high: set the pin to output mode with high level
Example:
- i2c_gpio_expander@20{
+ i2c0gpio-expander@20{
#gpio-cells = <2>;
#interrupt-cells = <2>;
compatible = "semtech,sx1506q";
@@ -38,4 +58,12 @@ Example:
gpio-controller;
interrupt-controller;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&gpio1_cfg_pins>;
+
+ gpio1_cfg_pins: gpio1-cfg {
+ pins = "gpio1";
+ bias-pull-up;
+ };
};
diff --git a/drivers/gpio/Kconfig b/drivers/gpio/Kconfig
index 26ee00f..db3f7aa 100644
--- a/drivers/gpio/Kconfig
+++ b/drivers/gpio/Kconfig
@@ -781,16 +781,13 @@ config GPIO_PCF857X
platform-neutral GPIO calls.
config GPIO_SX150X
- bool "Semtech SX150x I2C GPIO expander"
- depends on I2C=y
- select GPIOLIB_IRQCHIP
+ bool "Semtech SX150x I2C GPIO expander (deprecated)"
+ depends on PINCTRL && I2C=y
+ select PINCTRL_SX150X
default n
help
- Say yes here to provide support for Semtech SX150-series I2C
- GPIO expanders. Compatible models include:
-
- 8 bits: sx1508q
- 16 bits: sx1509q
+ Say yes here to provide support for Semtech SX150x-series I2C
+ GPIO expanders. The GPIO driver was replaced by a Pinctrl version.
config GPIO_TPIC2810
tristate "TPIC2810 8-Bit I2C GPO expander"
diff --git a/drivers/gpio/Makefile b/drivers/gpio/Makefile
index ab28a2d..76c7af6 100644
--- a/drivers/gpio/Makefile
+++ b/drivers/gpio/Makefile
@@ -102,7 +102,6 @@ obj-$(CONFIG_GPIO_SPEAR_SPICS) += gpio-spear-spics.o
obj-$(CONFIG_GPIO_STA2X11) += gpio-sta2x11.o
obj-$(CONFIG_GPIO_STMPE) += gpio-stmpe.o
obj-$(CONFIG_GPIO_STP_XWAY) += gpio-stp-xway.o
-obj-$(CONFIG_GPIO_SX150X) += gpio-sx150x.o
obj-$(CONFIG_GPIO_SYSCON) += gpio-syscon.o
obj-$(CONFIG_GPIO_TB10X) += gpio-tb10x.o
obj-$(CONFIG_GPIO_TC3589X) += gpio-tc3589x.o
diff --git a/drivers/pinctrl/Kconfig b/drivers/pinctrl/Kconfig
index 0e75d94..801fa8b 100644
--- a/drivers/pinctrl/Kconfig
+++ b/drivers/pinctrl/Kconfig
@@ -164,6 +164,20 @@ config PINCTRL_SIRF
select GENERIC_PINCONF
select GPIOLIB_IRQCHIP
+config PINCTRL_SX150X
+ bool "Semtech SX150x I2C GPIO expander pinctrl driver"
+ depends on GPIOLIB && I2C=y
+ select PINMUX
+ select PINCONF
+ select GENERIC_PINCONF
+ select GPIOLIB_IRQCHIP
+ help
+ Say yes here to provide support for Semtech SX150x-series I2C
+ GPIO expanders as pinctrl module.
+ Compatible models include:
+ - 8 bits: sx1508q, sx1502q
+ - 16 bits: sx1509q, sx1506q
+
config PINCTRL_PISTACHIO
def_bool y if MACH_PISTACHIO
depends on GPIOLIB
diff --git a/drivers/pinctrl/Makefile b/drivers/pinctrl/Makefile
index 11bad37..3b8e6f7 100644
--- a/drivers/pinctrl/Makefile
+++ b/drivers/pinctrl/Makefile
@@ -25,6 +25,7 @@ obj-$(CONFIG_PINCTRL_PISTACHIO) += pinctrl-pistachio.o
obj-$(CONFIG_PINCTRL_ROCKCHIP) += pinctrl-rockchip.o
obj-$(CONFIG_PINCTRL_SINGLE) += pinctrl-single.o
obj-$(CONFIG_PINCTRL_SIRF) += sirf/
+obj-$(CONFIG_PINCTRL_SX150X) += pinctrl-sx150x.o
obj-$(CONFIG_ARCH_TEGRA) += tegra/
obj-$(CONFIG_PINCTRL_TZ1090) += pinctrl-tz1090.o
obj-$(CONFIG_PINCTRL_TZ1090_PDC) += pinctrl-tz1090-pdc.o
diff --git a/drivers/gpio/gpio-sx150x.c b/drivers/pinctrl/pinctrl-sx150x.c
similarity index 23%
rename from drivers/gpio/gpio-sx150x.c
rename to drivers/pinctrl/pinctrl-sx150x.c
index af95de8..e985471 100644
--- a/drivers/gpio/gpio-sx150x.c
+++ b/drivers/pinctrl/pinctrl-sx150x.c
@@ -1,4 +1,8 @@
-/* Copyright (c) 2010, Code Aurora Forum. All rights reserved.
+/*
+ * Copyright (c) 2016, BayLibre, SAS. All rights reserved.
+ * Author: Neil Armstrong <narmstrong@...libre.com>
+ *
+ * Copyright (c) 2010, Code Aurora Forum. All rights reserved.
*
* Driver for Semtech SX150X I2C GPIO Expanders
*
@@ -12,13 +16,8 @@
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA
- * 02110-1301, USA.
*/
-#include <linux/gpio.h>
+
#include <linux/i2c.h>
#include <linux/init.h>
#include <linux/interrupt.h>
@@ -26,17 +25,23 @@
#include <linux/mutex.h>
#include <linux/slab.h>
#include <linux/of.h>
-#include <linux/of_address.h>
-#include <linux/of_irq.h>
-#include <linux/of_gpio.h>
-#include <linux/of_device.h>
+#include <linux/gpio.h>
+#include <linux/pinctrl/machine.h>
+#include <linux/pinctrl/pinconf.h>
+#include <linux/pinctrl/pinctrl.h>
+#include <linux/pinctrl/pinmux.h>
+#include <linux/pinctrl/pinconf-generic.h>
-#define NO_UPDATE_PENDING -1
+#include "core.h"
+#include "pinconf.h"
+#include "pinctrl-utils.h"
/* The chip models of sx150x */
-#define SX150X_123 0
-#define SX150X_456 1
-#define SX150X_789 2
+enum {
+ SX150X_123 = 0,
+ SX150X_456,
+ SX150X_789,
+};
struct sx150x_123_pri {
u8 reg_pld_mode;
@@ -82,167 +87,146 @@ struct sx150x_device_data {
struct sx150x_456_pri x456;
struct sx150x_789_pri x789;
} pri;
+ const struct pinctrl_pin_desc *pins;
+ unsigned int npins;
};
-/**
- * struct sx150x_platform_data - config data for SX150x driver
- * @gpio_base: The index number of the first GPIO assigned to this
- * GPIO expander. The expander will create a block of
- * consecutively numbered gpios beginning at the given base,
- * with the size of the block depending on the model of the
- * expander chip.
- * @oscio_is_gpo: If set to true, the driver will configure OSCIO as a GPO
- * instead of as an oscillator, increasing the size of the
- * GP(I)O pool created by this expander by one. The
- * output-only GPO pin will be added at the end of the block.
- * @io_pullup_ena: A bit-mask which enables or disables the pull-up resistor
- * for each IO line in the expander. Setting the bit at
- * position n will enable the pull-up for the IO at
- * the corresponding offset. For chips with fewer than
- * 16 IO pins, high-end bits are ignored.
- * @io_pulldn_ena: A bit-mask which enables-or disables the pull-down
- * resistor for each IO line in the expander. Setting the
- * bit at position n will enable the pull-down for the IO at
- * the corresponding offset. For chips with fewer than
- * 16 IO pins, high-end bits are ignored.
- * @io_polarity: A bit-mask which enables polarity inversion for each IO line
- * in the expander. Setting the bit at position n inverts
- * the polarity of that IO line, while clearing it results
- * in normal polarity. For chips with fewer than 16 IO pins,
- * high-end bits are ignored.
- * @irq_summary: The 'summary IRQ' line to which the GPIO expander's INT line
- * is connected, via which it reports interrupt events
- * across all GPIO lines. This must be a real,
- * pre-existing IRQ line.
- * Setting this value < 0 disables the irq_chip functionality
- * of the driver.
- * @irq_base: The first 'virtual IRQ' line at which our block of GPIO-based
- * IRQ lines will appear. Similarly to gpio_base, the expander
- * will create a block of irqs beginning at this number.
- * This value is ignored if irq_summary is < 0.
- * @reset_during_probe: If set to true, the driver will trigger a full
- * reset of the chip at the beginning of the probe
- * in order to place it in a known state.
- */
-struct sx150x_platform_data {
- unsigned gpio_base;
- bool oscio_is_gpo;
- u16 io_pullup_ena;
- u16 io_pulldn_ena;
- u16 io_polarity;
- int irq_summary;
- unsigned irq_base;
- bool reset_during_probe;
+struct sx150x_pinctrl {
+ struct device *dev;
+ struct i2c_client *client;
+ struct pinctrl_dev *pctldev;
+ struct pinctrl_desc pinctrl_desc;
+ struct gpio_chip gpio;
+ struct irq_chip irq_chip;
+ struct {
+ int update;
+ u32 sense;
+ u32 masked;
+ u32 dev_sense;
+ u32 dev_masked;
+ } irq;
+ struct mutex lock;
+ const struct sx150x_device_data *data;
};
-struct sx150x_chip {
- struct gpio_chip gpio_chip;
- struct i2c_client *client;
- const struct sx150x_device_data *dev_cfg;
- int irq_summary;
- int irq_base;
- int irq_update;
- u32 irq_sense;
- u32 irq_masked;
- u32 dev_sense;
- u32 dev_masked;
- struct irq_chip irq_chip;
- struct mutex lock;
+static const struct pinctrl_pin_desc sx150x_8_pins[] = {
+ PINCTRL_PIN(0, "gpio0"),
+ PINCTRL_PIN(1, "gpio1"),
+ PINCTRL_PIN(2, "gpio2"),
+ PINCTRL_PIN(3, "gpio3"),
+ PINCTRL_PIN(4, "gpio4"),
+ PINCTRL_PIN(5, "gpio5"),
+ PINCTRL_PIN(6, "gpio6"),
+ PINCTRL_PIN(7, "gpio7"),
+ PINCTRL_PIN(8, "oscio"),
};
-static const struct sx150x_device_data sx150x_devices[] = {
- [0] = { /* sx1508q */
- .model = SX150X_789,
- .reg_pullup = 0x03,
- .reg_pulldn = 0x04,
- .reg_dir = 0x07,
- .reg_data = 0x08,
- .reg_irq_mask = 0x09,
- .reg_irq_src = 0x0c,
- .reg_sense = 0x0b,
- .pri.x789 = {
- .reg_drain = 0x05,
- .reg_polarity = 0x06,
- .reg_clock = 0x0f,
- .reg_misc = 0x10,
- .reg_reset = 0x7d,
- },
- .ngpios = 8,
- },
- [1] = { /* sx1509q */
- .model = SX150X_789,
- .reg_pullup = 0x07,
- .reg_pulldn = 0x09,
- .reg_dir = 0x0f,
- .reg_data = 0x11,
- .reg_irq_mask = 0x13,
- .reg_irq_src = 0x19,
- .reg_sense = 0x17,
- .pri.x789 = {
- .reg_drain = 0x0b,
- .reg_polarity = 0x0d,
- .reg_clock = 0x1e,
- .reg_misc = 0x1f,
- .reg_reset = 0x7d,
- },
- .ngpios = 16
- },
- [2] = { /* sx1506q */
- .model = SX150X_456,
- .reg_pullup = 0x05,
- .reg_pulldn = 0x07,
- .reg_dir = 0x03,
- .reg_data = 0x01,
- .reg_irq_mask = 0x09,
- .reg_irq_src = 0x0f,
- .reg_sense = 0x0d,
- .pri.x456 = {
- .reg_pld_mode = 0x21,
- .reg_pld_table0 = 0x23,
- .reg_pld_table1 = 0x25,
- .reg_pld_table2 = 0x27,
- .reg_pld_table3 = 0x29,
- .reg_pld_table4 = 0x2b,
- .reg_advance = 0xad,
- },
- .ngpios = 16
+static const struct pinctrl_pin_desc sx150x_16_pins[] = {
+ PINCTRL_PIN(0, "gpio0"),
+ PINCTRL_PIN(1, "gpio1"),
+ PINCTRL_PIN(2, "gpio2"),
+ PINCTRL_PIN(3, "gpio3"),
+ PINCTRL_PIN(4, "gpio4"),
+ PINCTRL_PIN(5, "gpio5"),
+ PINCTRL_PIN(6, "gpio6"),
+ PINCTRL_PIN(7, "gpio7"),
+ PINCTRL_PIN(8, "gpio8"),
+ PINCTRL_PIN(9, "gpio9"),
+ PINCTRL_PIN(10, "gpio10"),
+ PINCTRL_PIN(11, "gpio11"),
+ PINCTRL_PIN(12, "gpio12"),
+ PINCTRL_PIN(13, "gpio13"),
+ PINCTRL_PIN(14, "gpio14"),
+ PINCTRL_PIN(15, "gpio15"),
+ PINCTRL_PIN(16, "oscio"),
+};
+
+static const struct sx150x_device_data sx1508q_device_data = {
+ .model = SX150X_789,
+ .reg_pullup = 0x03,
+ .reg_pulldn = 0x04,
+ .reg_dir = 0x07,
+ .reg_data = 0x08,
+ .reg_irq_mask = 0x09,
+ .reg_irq_src = 0x0c,
+ .reg_sense = 0x0b,
+ .pri.x789 = {
+ .reg_drain = 0x05,
+ .reg_polarity = 0x06,
+ .reg_clock = 0x0f,
+ .reg_misc = 0x10,
+ .reg_reset = 0x7d,
},
- [3] = { /* sx1502q */
- .model = SX150X_123,
- .reg_pullup = 0x02,
- .reg_pulldn = 0x03,
- .reg_dir = 0x01,
- .reg_data = 0x00,
- .reg_irq_mask = 0x05,
- .reg_irq_src = 0x08,
- .reg_sense = 0x07,
- .pri.x123 = {
- .reg_pld_mode = 0x10,
- .reg_pld_table0 = 0x11,
- .reg_pld_table1 = 0x12,
- .reg_pld_table2 = 0x13,
- .reg_pld_table3 = 0x14,
- .reg_pld_table4 = 0x15,
- .reg_advance = 0xad,
- },
- .ngpios = 8,
+ .ngpios = 8,
+ .pins = sx150x_8_pins,
+ .npins = ARRAY_SIZE(sx150x_8_pins),
+};
+
+static const struct sx150x_device_data sx1509q_device_data = {
+ .model = SX150X_789,
+ .reg_pullup = 0x07,
+ .reg_pulldn = 0x09,
+ .reg_dir = 0x0f,
+ .reg_data = 0x11,
+ .reg_irq_mask = 0x13,
+ .reg_irq_src = 0x19,
+ .reg_sense = 0x17,
+ .pri.x789 = {
+ .reg_drain = 0x0b,
+ .reg_polarity = 0x0d,
+ .reg_clock = 0x1e,
+ .reg_misc = 0x1f,
+ .reg_reset = 0x7d,
},
+ .ngpios = 16,
+ .pins = sx150x_16_pins,
+ .npins = ARRAY_SIZE(sx150x_16_pins),
};
-static const struct i2c_device_id sx150x_id[] = {
- {"sx1508q", 0},
- {"sx1509q", 1},
- {"sx1506q", 2},
- {"sx1502q", 3},
- {}
+static const struct sx150x_device_data sx1506q_device_data = {
+ .model = SX150X_456,
+ .reg_pullup = 0x05,
+ .reg_pulldn = 0x07,
+ .reg_dir = 0x03,
+ .reg_data = 0x01,
+ .reg_irq_mask = 0x09,
+ .reg_irq_src = 0x0f,
+ .reg_sense = 0x0d,
+ .pri.x456 = {
+ .reg_pld_mode = 0x21,
+ .reg_pld_table0 = 0x23,
+ .reg_pld_table1 = 0x25,
+ .reg_pld_table2 = 0x27,
+ .reg_pld_table3 = 0x29,
+ .reg_pld_table4 = 0x2b,
+ .reg_advance = 0xad,
+ },
+ .ngpios = 16,
+ .pins = sx150x_16_pins,
+ .npins = 16, /* oscio not available */
};
-static const struct of_device_id sx150x_of_match[] = {
- { .compatible = "semtech,sx1508q" },
- { .compatible = "semtech,sx1509q" },
- { .compatible = "semtech,sx1506q" },
- { .compatible = "semtech,sx1502q" },
- {},
+static const struct sx150x_device_data sx1502q_device_data = {
+ .model = SX150X_123,
+ .reg_pullup = 0x02,
+ .reg_pulldn = 0x03,
+ .reg_dir = 0x01,
+ .reg_data = 0x00,
+ .reg_irq_mask = 0x05,
+ .reg_irq_src = 0x08,
+ .reg_sense = 0x07,
+ .pri.x123 = {
+ .reg_pld_mode = 0x10,
+ .reg_pld_table0 = 0x11,
+ .reg_pld_table1 = 0x12,
+ .reg_pld_table2 = 0x13,
+ .reg_pld_table3 = 0x14,
+ .reg_pld_table4 = 0x15,
+ .reg_advance = 0xad,
+ },
+ .ngpios = 8,
+ .pins = sx150x_8_pins,
+ .npins = 8, /* oscio not available */
};
static s32 sx150x_i2c_write(struct i2c_client *client, u8 reg, u8 val)
@@ -269,11 +253,6 @@ static s32 sx150x_i2c_read(struct i2c_client *client, u8 reg, u8 *val)
return err;
}
-static inline bool offset_is_oscio(struct sx150x_chip *chip, unsigned offset)
-{
- return (chip->dev_cfg->ngpios == offset);
-}
-
/*
* These utility functions solve the common problem of locating and setting
* configuration bits. Configuration bits are grouped into registers
@@ -294,7 +273,7 @@ static inline bool offset_is_oscio(struct sx150x_chip *chip, unsigned offset)
* register and mask the correct bits.
*/
static inline void sx150x_find_cfg(u8 offset, u8 width,
- u8 *reg, u8 *mask, u8 *shift)
+ u8 *reg, u8 *mask, u8 *shift)
{
*reg -= offset * width / 8;
*mask = (1 << width) - 1;
@@ -302,185 +281,241 @@ static inline void sx150x_find_cfg(u8 offset, u8 width,
*mask <<= *shift;
}
-static s32 sx150x_write_cfg(struct sx150x_chip *chip,
- u8 offset, u8 width, u8 reg, u8 val)
+static int sx150x_write_cfg(struct i2c_client *client,
+ u8 offset, u8 width, u8 reg, u8 val)
{
u8 mask;
u8 data;
u8 shift;
- s32 err;
+ int err;
sx150x_find_cfg(offset, width, ®, &mask, &shift);
- err = sx150x_i2c_read(chip->client, reg, &data);
+ err = sx150x_i2c_read(client, reg, &data);
if (err < 0)
return err;
data &= ~mask;
data |= (val << shift) & mask;
- return sx150x_i2c_write(chip->client, reg, data);
+ return sx150x_i2c_write(client, reg, data);
}
-static int sx150x_get_io(struct sx150x_chip *chip, unsigned offset)
+static int sx150x_read_cfg(struct i2c_client *client,
+ u8 offset, u8 width, u8 reg)
{
- u8 reg = chip->dev_cfg->reg_data;
u8 mask;
u8 data;
u8 shift;
- s32 err;
+ int err;
- sx150x_find_cfg(offset, 1, ®, &mask, &shift);
- err = sx150x_i2c_read(chip->client, reg, &data);
- if (err >= 0)
- err = (data & mask) != 0 ? 1 : 0;
+ sx150x_find_cfg(offset, width, ®, &mask, &shift);
+ err = sx150x_i2c_read(client, reg, &data);
+ if (err < 0)
+ return err;
- return err;
+ return (data & mask);
}
-static void sx150x_set_oscio(struct sx150x_chip *chip, int val)
+static int sx150x_pinctrl_get_groups_count(struct pinctrl_dev *pctldev)
{
- sx150x_i2c_write(chip->client,
- chip->dev_cfg->pri.x789.reg_clock,
- (val ? 0x1f : 0x10));
+ return 0;
}
-static void sx150x_set_io(struct sx150x_chip *chip, unsigned offset, int val)
+static const char *sx150x_pinctrl_get_group_name(struct pinctrl_dev *pctldev,
+ unsigned int group)
{
- sx150x_write_cfg(chip,
- offset,
- 1,
- chip->dev_cfg->reg_data,
- (val ? 1 : 0));
+ return NULL;
}
-static int sx150x_io_input(struct sx150x_chip *chip, unsigned offset)
+static int sx150x_pinctrl_get_group_pins(struct pinctrl_dev *pctldev,
+ unsigned int group,
+ const unsigned int **pins,
+ unsigned int *num_pins)
{
- return sx150x_write_cfg(chip,
- offset,
- 1,
- chip->dev_cfg->reg_dir,
- 1);
+ return -ENOTSUPP;
}
-static int sx150x_io_output(struct sx150x_chip *chip, unsigned offset, int val)
+static const struct pinctrl_ops sx150x_pinctrl_ops = {
+ .get_groups_count = sx150x_pinctrl_get_groups_count,
+ .get_group_name = sx150x_pinctrl_get_group_name,
+ .get_group_pins = sx150x_pinctrl_get_group_pins,
+#ifdef CONFIG_OF
+ .dt_node_to_map = pinconf_generic_dt_node_to_map_pin,
+ .dt_free_map = pinctrl_utils_free_map,
+#endif
+};
+
+static bool sx150x_pin_is_oscio(struct sx150x_pinctrl *pctl, unsigned int pin)
{
- int err;
+ if (pin >= pctl->data->npins)
+ return false;
- err = sx150x_write_cfg(chip,
- offset,
- 1,
- chip->dev_cfg->reg_data,
- (val ? 1 : 0));
- if (err >= 0)
- err = sx150x_write_cfg(chip,
- offset,
- 1,
- chip->dev_cfg->reg_dir,
- 0);
- return err;
+ /* OSCIO pin is only present in 789 devices */
+ if (pctl->data->model != SX150X_789)
+ return false;
+
+ return !strcmp(pctl->data->pins[pin].name, "oscio");
}
-static int sx150x_gpio_get(struct gpio_chip *gc, unsigned offset)
+static int sx150x_gpio_get_direction(struct gpio_chip *chip,
+ unsigned int offset)
{
- struct sx150x_chip *chip = gpiochip_get_data(gc);
- int status = -EINVAL;
+ struct sx150x_pinctrl *pctl = gpiochip_get_data(chip);
+ int status;
- if (!offset_is_oscio(chip, offset)) {
- mutex_lock(&chip->lock);
- status = sx150x_get_io(chip, offset);
- mutex_unlock(&chip->lock);
- }
+ if (sx150x_pin_is_oscio(pctl, offset))
+ return false;
+
+ status = sx150x_read_cfg(pctl->client, offset, 1, pctl->data->reg_dir);
+ if (status >= 0)
+ status = !!status;
- return (status < 0) ? status : !!status;
+ return status;
}
-static void sx150x_gpio_set(struct gpio_chip *gc, unsigned offset, int val)
+static int sx150x_gpio_get(struct gpio_chip *chip, unsigned int offset)
{
- struct sx150x_chip *chip = gpiochip_get_data(gc);
+ struct sx150x_pinctrl *pctl = gpiochip_get_data(chip);
+ int status;
- mutex_lock(&chip->lock);
- if (offset_is_oscio(chip, offset))
- sx150x_set_oscio(chip, val);
- else
- sx150x_set_io(chip, offset, val);
- mutex_unlock(&chip->lock);
+ if (sx150x_pin_is_oscio(pctl, offset))
+ return -EINVAL;
+
+ status = sx150x_read_cfg(pctl->client, offset, 1, pctl->data->reg_data);
+ if (status >= 0)
+ status = !!status;
+
+ return status;
}
-static int sx150x_gpio_set_single_ended(struct gpio_chip *gc,
- unsigned offset,
- enum single_ended_mode mode)
+static int sx150x_gpio_set_single_ended(struct gpio_chip *chip,
+ unsigned int offset,
+ enum single_ended_mode mode)
{
- struct sx150x_chip *chip = gpiochip_get_data(gc);
-
- /* On the SX160X 789 we can set open drain */
- if (chip->dev_cfg->model != SX150X_789)
+ struct sx150x_pinctrl *pctl = gpiochip_get_data(chip);
+ int ret;
+
+ switch (mode) {
+ case LINE_MODE_PUSH_PULL:
+ if (pctl->data->model != SX150X_789 ||
+ sx150x_pin_is_oscio(pctl, offset))
+ return 0;
+
+ mutex_lock(&pctl->lock);
+ ret = sx150x_write_cfg(pctl->client, offset, 1,
+ pctl->data->pri.x789.reg_drain,
+ 0);
+ mutex_unlock(&pctl->lock);
+ if (ret < 0)
+ return ret;
+ break;
+
+ case LINE_MODE_OPEN_DRAIN:
+ if (pctl->data->model != SX150X_789 ||
+ sx150x_pin_is_oscio(pctl, offset))
+ return -ENOTSUPP;
+
+ mutex_lock(&pctl->lock);
+ ret = sx150x_write_cfg(pctl->client, offset, 1,
+ pctl->data->pri.x789.reg_drain,
+ 1);
+ mutex_unlock(&pctl->lock);
+ if (ret < 0)
+ return ret;
+ break;
+
+ default:
return -ENOTSUPP;
+ }
- if (mode == LINE_MODE_PUSH_PULL)
- return sx150x_write_cfg(chip,
- offset,
- 1,
- chip->dev_cfg->pri.x789.reg_drain,
- 0);
-
- if (mode == LINE_MODE_OPEN_DRAIN)
- return sx150x_write_cfg(chip,
- offset,
- 1,
- chip->dev_cfg->pri.x789.reg_drain,
- 1);
- return -ENOTSUPP;
+ return 0;
}
-static int sx150x_gpio_direction_input(struct gpio_chip *gc, unsigned offset)
+static void sx150x_gpio_set(struct gpio_chip *chip, unsigned int offset,
+ int value)
{
- struct sx150x_chip *chip = gpiochip_get_data(gc);
- int status = -EINVAL;
+ struct sx150x_pinctrl *pctl = gpiochip_get_data(chip);
+
+ if (sx150x_pin_is_oscio(pctl, offset)) {
- if (!offset_is_oscio(chip, offset)) {
- mutex_lock(&chip->lock);
- status = sx150x_io_input(chip, offset);
- mutex_unlock(&chip->lock);
+ mutex_lock(&pctl->lock);
+ sx150x_i2c_write(pctl->client,
+ pctl->data->pri.x789.reg_clock,
+ (value ? 0x1f : 0x10));
+ mutex_unlock(&pctl->lock);
+ } else {
+ mutex_lock(&pctl->lock);
+ sx150x_write_cfg(pctl->client, offset, 1,
+ pctl->data->reg_data,
+ (value ? 1 : 0));
+ mutex_unlock(&pctl->lock);
}
- return status;
}
-static int sx150x_gpio_direction_output(struct gpio_chip *gc,
- unsigned offset,
- int val)
+static int sx150x_gpio_direction_input(struct gpio_chip *chip,
+ unsigned int offset)
{
- struct sx150x_chip *chip = gpiochip_get_data(gc);
- int status = 0;
+ struct sx150x_pinctrl *pctl = gpiochip_get_data(chip);
+ int ret;
- if (!offset_is_oscio(chip, offset)) {
- mutex_lock(&chip->lock);
- status = sx150x_io_output(chip, offset, val);
- mutex_unlock(&chip->lock);
+ if (sx150x_pin_is_oscio(pctl, offset))
+ return -EINVAL;
+
+ mutex_lock(&pctl->lock);
+ ret = sx150x_write_cfg(pctl->client, offset, 1,
+ pctl->data->reg_dir, 1);
+ mutex_unlock(&pctl->lock);
+
+ return ret;
+}
+
+static int sx150x_gpio_direction_output(struct gpio_chip *chip,
+ unsigned int offset, int value)
+{
+ struct sx150x_pinctrl *pctl = gpiochip_get_data(chip);
+ int status;
+
+ if (sx150x_pin_is_oscio(pctl, offset)) {
+ sx150x_gpio_set(chip, offset, value);
+ return 0;
}
+
+ mutex_lock(&pctl->lock);
+ status = sx150x_write_cfg(pctl->client, offset, 1,
+ pctl->data->reg_data,
+ (value ? 1 : 0));
+ if (status >= 0)
+ status = sx150x_write_cfg(pctl->client, offset, 1,
+ pctl->data->reg_dir, 0);
+ mutex_unlock(&pctl->lock);
+
return status;
}
static void sx150x_irq_mask(struct irq_data *d)
{
- struct sx150x_chip *chip = gpiochip_get_data(irq_data_get_irq_chip_data(d));
- unsigned n = d->hwirq;
+ struct sx150x_pinctrl *pctl =
+ gpiochip_get_data(irq_data_get_irq_chip_data(d));
+ unsigned int n = d->hwirq;
- chip->irq_masked |= (1 << n);
- chip->irq_update = n;
+ pctl->irq.masked |= (1 << n);
+ pctl->irq.update = n;
}
static void sx150x_irq_unmask(struct irq_data *d)
{
- struct sx150x_chip *chip = gpiochip_get_data(irq_data_get_irq_chip_data(d));
- unsigned n = d->hwirq;
+ struct sx150x_pinctrl *pctl =
+ gpiochip_get_data(irq_data_get_irq_chip_data(d));
+ unsigned int n = d->hwirq;
- chip->irq_masked &= ~(1 << n);
- chip->irq_update = n;
+ pctl->irq.masked &= ~(1 << n);
+ pctl->irq.update = n;
}
static int sx150x_irq_set_type(struct irq_data *d, unsigned int flow_type)
{
- struct sx150x_chip *chip = gpiochip_get_data(irq_data_get_irq_chip_data(d));
- unsigned n, val = 0;
+ struct sx150x_pinctrl *pctl =
+ gpiochip_get_data(irq_data_get_irq_chip_data(d));
+ unsigned int n, val = 0;
if (flow_type & (IRQ_TYPE_LEVEL_HIGH | IRQ_TYPE_LEVEL_LOW))
return -EINVAL;
@@ -492,37 +527,40 @@ static int sx150x_irq_set_type(struct irq_data *d, unsigned int flow_type)
if (flow_type & IRQ_TYPE_EDGE_FALLING)
val |= 0x2;
- chip->irq_sense &= ~(3UL << (n * 2));
- chip->irq_sense |= val << (n * 2);
- chip->irq_update = n;
+ pctl->irq.sense &= ~(3UL << (n * 2));
+ pctl->irq.sense |= val << (n * 2);
+ pctl->irq.update = n;
return 0;
}
static irqreturn_t sx150x_irq_thread_fn(int irq, void *dev_id)
{
- struct sx150x_chip *chip = (struct sx150x_chip *)dev_id;
- unsigned nhandled = 0;
- unsigned sub_irq;
- unsigned n;
+ struct sx150x_pinctrl *pctl = (struct sx150x_pinctrl *)dev_id;
+ unsigned int nhandled = 0;
+ unsigned int sub_irq;
+ unsigned int n;
s32 err;
u8 val;
int i;
- for (i = (chip->dev_cfg->ngpios / 8) - 1; i >= 0; --i) {
- err = sx150x_i2c_read(chip->client,
- chip->dev_cfg->reg_irq_src - i,
+ for (i = (pctl->data->ngpios / 8) - 1; i >= 0; --i) {
+ err = sx150x_i2c_read(pctl->client,
+ pctl->data->reg_irq_src - i,
&val);
if (err < 0)
continue;
- sx150x_i2c_write(chip->client,
- chip->dev_cfg->reg_irq_src - i,
- val);
+ err = sx150x_i2c_write(pctl->client,
+ pctl->data->reg_irq_src - i,
+ val);
+ if (err < 0)
+ continue;
+
for (n = 0; n < 8; ++n) {
if (val & (1 << n)) {
sub_irq = irq_find_mapping(
- chip->gpio_chip.irqdomain,
- (i * 8) + n);
+ pctl->gpio.irqdomain,
+ (i * 8) + n);
handle_nested_irq(sub_irq);
++nhandled;
}
@@ -534,251 +572,483 @@ static irqreturn_t sx150x_irq_thread_fn(int irq, void *dev_id)
static void sx150x_irq_bus_lock(struct irq_data *d)
{
- struct sx150x_chip *chip = gpiochip_get_data(irq_data_get_irq_chip_data(d));
+ struct sx150x_pinctrl *pctl =
+ gpiochip_get_data(irq_data_get_irq_chip_data(d));
- mutex_lock(&chip->lock);
+ mutex_lock(&pctl->lock);
}
static void sx150x_irq_bus_sync_unlock(struct irq_data *d)
{
- struct sx150x_chip *chip = gpiochip_get_data(irq_data_get_irq_chip_data(d));
- unsigned n;
+ struct sx150x_pinctrl *pctl =
+ gpiochip_get_data(irq_data_get_irq_chip_data(d));
+ unsigned int n;
- if (chip->irq_update == NO_UPDATE_PENDING)
+ if (pctl->irq.update < 0)
goto out;
- n = chip->irq_update;
- chip->irq_update = NO_UPDATE_PENDING;
+ n = pctl->irq.update;
+ pctl->irq.update = -1;
/* Avoid updates if nothing changed */
- if (chip->dev_sense == chip->irq_sense &&
- chip->dev_masked == chip->irq_masked)
+ if (pctl->irq.dev_sense == pctl->irq.sense &&
+ pctl->irq.dev_masked == pctl->irq.masked)
goto out;
- chip->dev_sense = chip->irq_sense;
- chip->dev_masked = chip->irq_masked;
+ pctl->irq.dev_sense = pctl->irq.sense;
+ pctl->irq.dev_masked = pctl->irq.masked;
- if (chip->irq_masked & (1 << n)) {
- sx150x_write_cfg(chip, n, 1, chip->dev_cfg->reg_irq_mask, 1);
- sx150x_write_cfg(chip, n, 2, chip->dev_cfg->reg_sense, 0);
+ if (pctl->irq.masked & (1 << n)) {
+ sx150x_write_cfg(pctl->client, n, 1,
+ pctl->data->reg_irq_mask, 1);
+ sx150x_write_cfg(pctl->client, n, 2,
+ pctl->data->reg_sense, 0);
} else {
- sx150x_write_cfg(chip, n, 1, chip->dev_cfg->reg_irq_mask, 0);
- sx150x_write_cfg(chip, n, 2, chip->dev_cfg->reg_sense,
- chip->irq_sense >> (n * 2));
+ sx150x_write_cfg(pctl->client, n, 1,
+ pctl->data->reg_irq_mask, 0);
+ sx150x_write_cfg(pctl->client, n, 2,
+ pctl->data->reg_sense,
+ pctl->irq.sense >> (n * 2));
}
out:
- mutex_unlock(&chip->lock);
+ mutex_unlock(&pctl->lock);
}
-static void sx150x_init_chip(struct sx150x_chip *chip,
- struct i2c_client *client,
- kernel_ulong_t driver_data,
- struct sx150x_platform_data *pdata)
+static int sx150x_pinconf_get(struct pinctrl_dev *pctldev, unsigned int pin,
+ unsigned long *config)
{
- mutex_init(&chip->lock);
-
- chip->client = client;
- chip->dev_cfg = &sx150x_devices[driver_data];
- chip->gpio_chip.parent = &client->dev;
- chip->gpio_chip.label = client->name;
- chip->gpio_chip.direction_input = sx150x_gpio_direction_input;
- chip->gpio_chip.direction_output = sx150x_gpio_direction_output;
- chip->gpio_chip.get = sx150x_gpio_get;
- chip->gpio_chip.set = sx150x_gpio_set;
- chip->gpio_chip.set_single_ended = sx150x_gpio_set_single_ended;
- chip->gpio_chip.base = pdata->gpio_base;
- chip->gpio_chip.can_sleep = true;
- chip->gpio_chip.ngpio = chip->dev_cfg->ngpios;
-#ifdef CONFIG_OF_GPIO
- chip->gpio_chip.of_node = client->dev.of_node;
- chip->gpio_chip.of_gpio_n_cells = 2;
-#endif
- if (pdata->oscio_is_gpo)
- ++chip->gpio_chip.ngpio;
-
- chip->irq_chip.name = client->name;
- chip->irq_chip.irq_mask = sx150x_irq_mask;
- chip->irq_chip.irq_unmask = sx150x_irq_unmask;
- chip->irq_chip.irq_set_type = sx150x_irq_set_type;
- chip->irq_chip.irq_bus_lock = sx150x_irq_bus_lock;
- chip->irq_chip.irq_bus_sync_unlock = sx150x_irq_bus_sync_unlock;
- chip->irq_summary = -1;
- chip->irq_base = -1;
- chip->irq_masked = ~0;
- chip->irq_sense = 0;
- chip->dev_masked = ~0;
- chip->dev_sense = 0;
- chip->irq_update = NO_UPDATE_PENDING;
+ struct sx150x_pinctrl *pctl = pinctrl_dev_get_drvdata(pctldev);
+ unsigned int param = pinconf_to_config_param(*config);
+ int ret;
+ u32 arg;
+
+ if (sx150x_pin_is_oscio(pctl, pin)) {
+ u8 data;
+
+ switch (param) {
+ case PIN_CONFIG_DRIVE_PUSH_PULL:
+ case PIN_CONFIG_OUTPUT:
+ mutex_lock(&pctl->lock);
+ ret = sx150x_i2c_read(pctl->client,
+ pctl->data->pri.x789.reg_clock,
+ &data);
+ mutex_unlock(&pctl->lock);
+
+ if (ret < 0)
+ return ret;
+
+ if (param == PIN_CONFIG_DRIVE_PUSH_PULL)
+ arg = (data & 0x1f) ? 1 : 0;
+ else {
+ if ((data & 0x1f) == 0x1f)
+ arg = 1;
+ else if ((data & 0x1f) == 0x10)
+ arg = 0;
+ else
+ return -EINVAL;
+ }
+
+ break;
+ default:
+ return -ENOTSUPP;
+ }
+
+ goto out;
+ }
+
+ switch (param) {
+ case PIN_CONFIG_BIAS_PULL_DOWN:
+ mutex_lock(&pctl->lock);
+ ret = sx150x_read_cfg(pctl->client, pin, 1,
+ pctl->data->reg_pulldn);
+ mutex_unlock(&pctl->lock);
+
+ if (ret < 0)
+ return ret;
+
+ if (!ret)
+ return -EINVAL;
+
+ arg = 1;
+ break;
+
+ case PIN_CONFIG_BIAS_PULL_UP:
+ mutex_lock(&pctl->lock);
+ ret = sx150x_read_cfg(pctl->client, pin, 1,
+ pctl->data->reg_pullup);
+ mutex_unlock(&pctl->lock);
+
+ if (ret < 0)
+ return ret;
+
+ if (!ret)
+ return -EINVAL;
+
+ arg = 1;
+ break;
+
+ case PIN_CONFIG_DRIVE_OPEN_DRAIN:
+ if (pctl->data->model != SX150X_789)
+ return -ENOTSUPP;
+
+ mutex_lock(&pctl->lock);
+ ret = sx150x_read_cfg(pctl->client, pin, 1,
+ pctl->data->pri.x789.reg_drain);
+ mutex_unlock(&pctl->lock);
+
+ if (ret < 0)
+ return ret;
+
+ if (!ret)
+ return -EINVAL;
+
+ arg = 1;
+ break;
+
+ case PIN_CONFIG_DRIVE_PUSH_PULL:
+ if (pctl->data->model != SX150X_789)
+ arg = true;
+ else {
+ mutex_lock(&pctl->lock);
+ ret = sx150x_read_cfg(pctl->client, pin, 1,
+ pctl->data->pri.x789.reg_drain);
+ mutex_unlock(&pctl->lock);
+
+ if (ret < 0)
+ return ret;
+
+ if (ret)
+ return -EINVAL;
+
+ arg = 1;
+ }
+ break;
+
+ case PIN_CONFIG_OUTPUT:
+ ret = sx150x_gpio_get_direction(&pctl->gpio, pin);
+ if (ret < 0)
+ return ret;
+
+ if (ret)
+ return -EINVAL;
+
+ ret = sx150x_gpio_get(&pctl->gpio, pin);
+ if (ret < 0)
+ return ret;
+
+ arg = ret;
+ break;
+
+ default:
+ return -ENOTSUPP;
+ }
+
+out:
+ *config = pinconf_to_config_packed(param, arg);
+
+ return 0;
+}
+
+static int sx150x_pinconf_set(struct pinctrl_dev *pctldev, unsigned int pin,
+ unsigned long *configs, unsigned int num_configs)
+{
+ struct sx150x_pinctrl *pctl = pinctrl_dev_get_drvdata(pctldev);
+ enum pin_config_param param;
+ u32 arg;
+ int i;
+ int ret;
+
+ for (i = 0; i < num_configs; i++) {
+ param = pinconf_to_config_param(configs[i]);
+ arg = pinconf_to_config_argument(configs[i]);
+
+ if (sx150x_pin_is_oscio(pctl, pin)) {
+ if (param == PIN_CONFIG_OUTPUT) {
+ ret = sx150x_gpio_direction_output(&pctl->gpio,
+ pin, arg);
+ if (ret < 0)
+ return ret;
+
+ continue;
+ } else
+ return -ENOTSUPP;
+ }
+
+ switch (param) {
+ case PIN_CONFIG_BIAS_PULL_PIN_DEFAULT:
+ case PIN_CONFIG_BIAS_DISABLE:
+ mutex_lock(&pctl->lock);
+ ret = sx150x_write_cfg(pctl->client, pin, 1,
+ pctl->data->reg_pulldn, 0);
+ mutex_unlock(&pctl->lock);
+ if (ret < 0)
+ return ret;
+
+ mutex_lock(&pctl->lock);
+ ret = sx150x_write_cfg(pctl->client, pin, 1,
+ pctl->data->reg_pullup, 0);
+ mutex_unlock(&pctl->lock);
+ if (ret < 0)
+ return ret;
+
+ break;
+
+ case PIN_CONFIG_BIAS_PULL_UP:
+ mutex_lock(&pctl->lock);
+ ret = sx150x_write_cfg(pctl->client, pin, 1,
+ pctl->data->reg_pullup,
+ 1);
+ mutex_unlock(&pctl->lock);
+ if (ret < 0)
+ return ret;
+
+ break;
+
+ case PIN_CONFIG_BIAS_PULL_DOWN:
+ mutex_lock(&pctl->lock);
+ ret = sx150x_write_cfg(pctl->client, pin, 1,
+ pctl->data->reg_pulldn,
+ 1);
+ mutex_unlock(&pctl->lock);
+ if (ret < 0)
+ return ret;
+
+ break;
+
+ case PIN_CONFIG_DRIVE_OPEN_DRAIN:
+ ret = sx150x_gpio_set_single_ended(&pctl->gpio,
+ pin, LINE_MODE_OPEN_DRAIN);
+ if (ret < 0)
+ return ret;
+
+ break;
+
+ case PIN_CONFIG_DRIVE_PUSH_PULL:
+ ret = sx150x_gpio_set_single_ended(&pctl->gpio,
+ pin, LINE_MODE_PUSH_PULL);
+ if (ret < 0)
+ return ret;
+
+ break;
+
+ case PIN_CONFIG_OUTPUT:
+ ret = sx150x_gpio_direction_output(&pctl->gpio,
+ pin, arg);
+ if (ret < 0)
+ return ret;
+
+ break;
+
+ default:
+ return -ENOTSUPP;
+ }
+ } /* for each config */
+
+ return 0;
}
-static int sx150x_init_io(struct sx150x_chip *chip, u8 base, u16 cfg)
+static const struct pinconf_ops sx150x_pinconf_ops = {
+ .pin_config_get = sx150x_pinconf_get,
+ .pin_config_set = sx150x_pinconf_set,
+ .is_generic = true,
+};
+
+static const struct i2c_device_id sx150x_id[] = {
+ {"sx1508q", (kernel_ulong_t) &sx1508q_device_data },
+ {"sx1509q", (kernel_ulong_t) &sx1509q_device_data },
+ {"sx1506q", (kernel_ulong_t) &sx1506q_device_data },
+ {"sx1502q", (kernel_ulong_t) &sx1502q_device_data },
+ {}
+};
+
+static const struct of_device_id sx150x_of_match[] = {
+ { .compatible = "semtech,sx1508q" },
+ { .compatible = "semtech,sx1509q" },
+ { .compatible = "semtech,sx1506q" },
+ { .compatible = "semtech,sx1502q" },
+ {},
+};
+
+static int sx150x_init_io(struct sx150x_pinctrl *pctl, u8 base, u16 cfg)
{
int err = 0;
- unsigned n;
+ unsigned int n;
- for (n = 0; err >= 0 && n < (chip->dev_cfg->ngpios / 8); ++n)
- err = sx150x_i2c_write(chip->client, base - n, cfg >> (n * 8));
+ for (n = 0; err >= 0 && n < (pctl->data->ngpios / 8); ++n)
+ err = sx150x_i2c_write(pctl->client, base - n, cfg >> (n * 8));
return err;
}
-static int sx150x_reset(struct sx150x_chip *chip)
+static int sx150x_reset(struct sx150x_pinctrl *pctl)
{
int err;
- err = i2c_smbus_write_byte_data(chip->client,
- chip->dev_cfg->pri.x789.reg_reset,
+ err = i2c_smbus_write_byte_data(pctl->client,
+ pctl->data->pri.x789.reg_reset,
0x12);
if (err < 0)
return err;
- err = i2c_smbus_write_byte_data(chip->client,
- chip->dev_cfg->pri.x789.reg_reset,
+ err = i2c_smbus_write_byte_data(pctl->client,
+ pctl->data->pri.x789.reg_reset,
0x34);
return err;
}
-static int sx150x_init_hw(struct sx150x_chip *chip,
- struct sx150x_platform_data *pdata)
+static int sx150x_init_hw(struct sx150x_pinctrl *pctl)
{
- int err = 0;
+ int err;
- if (pdata->reset_during_probe) {
- err = sx150x_reset(chip);
+ if (pctl->data->model == SX150X_789 &&
+ of_property_read_bool(pctl->dev->of_node, "semtech,probe-reset")) {
+ err = sx150x_reset(pctl);
if (err < 0)
return err;
}
- if (chip->dev_cfg->model == SX150X_789)
- err = sx150x_i2c_write(chip->client,
- chip->dev_cfg->pri.x789.reg_misc,
+ if (pctl->data->model == SX150X_789)
+ err = sx150x_i2c_write(pctl->client,
+ pctl->data->pri.x789.reg_misc,
0x01);
- else if (chip->dev_cfg->model == SX150X_456)
- err = sx150x_i2c_write(chip->client,
- chip->dev_cfg->pri.x456.reg_advance,
+ else if (pctl->data->model == SX150X_456)
+ err = sx150x_i2c_write(pctl->client,
+ pctl->data->pri.x456.reg_advance,
0x04);
else
- err = sx150x_i2c_write(chip->client,
- chip->dev_cfg->pri.x123.reg_advance,
+ err = sx150x_i2c_write(pctl->client,
+ pctl->data->pri.x123.reg_advance,
0x00);
if (err < 0)
return err;
- err = sx150x_init_io(chip, chip->dev_cfg->reg_pullup,
- pdata->io_pullup_ena);
- if (err < 0)
- return err;
-
- err = sx150x_init_io(chip, chip->dev_cfg->reg_pulldn,
- pdata->io_pulldn_ena);
- if (err < 0)
- return err;
-
- if (chip->dev_cfg->model == SX150X_789) {
- err = sx150x_init_io(chip,
- chip->dev_cfg->pri.x789.reg_polarity,
- pdata->io_polarity);
+ /* Set all pins to work in normal mode */
+ if (pctl->data->model == SX150X_789) {
+ err = sx150x_init_io(pctl,
+ pctl->data->pri.x789.reg_polarity,
+ 0);
if (err < 0)
return err;
- } else if (chip->dev_cfg->model == SX150X_456) {
+ } else if (pctl->data->model == SX150X_456) {
/* Set all pins to work in normal mode */
- err = sx150x_init_io(chip,
- chip->dev_cfg->pri.x456.reg_pld_mode,
+ err = sx150x_init_io(pctl,
+ pctl->data->pri.x456.reg_pld_mode,
0);
if (err < 0)
return err;
} else {
/* Set all pins to work in normal mode */
- err = sx150x_init_io(chip,
- chip->dev_cfg->pri.x123.reg_pld_mode,
+ err = sx150x_init_io(pctl,
+ pctl->data->pri.x123.reg_pld_mode,
0);
if (err < 0)
return err;
}
-
- if (pdata->oscio_is_gpo)
- sx150x_set_oscio(chip, 0);
-
- return err;
-}
-
-static int sx150x_install_irq_chip(struct sx150x_chip *chip,
- int irq_summary,
- int irq_base)
-{
- int err;
-
- chip->irq_summary = irq_summary;
- chip->irq_base = irq_base;
-
- /* Add gpio chip to irq subsystem */
- err = gpiochip_irqchip_add(&chip->gpio_chip,
- &chip->irq_chip, chip->irq_base,
- handle_edge_irq, IRQ_TYPE_EDGE_BOTH);
- if (err) {
- dev_err(&chip->client->dev,
- "could not connect irqchip to gpiochip\n");
- return err;
- }
-
- err = devm_request_threaded_irq(&chip->client->dev,
- irq_summary, NULL, sx150x_irq_thread_fn,
- IRQF_ONESHOT | IRQF_SHARED | IRQF_TRIGGER_FALLING,
- chip->irq_chip.name, chip);
- if (err < 0) {
- chip->irq_summary = -1;
- chip->irq_base = -1;
- }
-
- return err;
+ return 0;
}
static int sx150x_probe(struct i2c_client *client,
- const struct i2c_device_id *id)
+ const struct i2c_device_id *id)
{
static const u32 i2c_funcs = I2C_FUNC_SMBUS_BYTE_DATA |
I2C_FUNC_SMBUS_WRITE_WORD_DATA;
- struct sx150x_platform_data *pdata;
- struct sx150x_chip *chip;
- int rc;
+ struct device *dev = &client->dev;
+ struct sx150x_pinctrl *pctl;
+ int ret;
- pdata = dev_get_platdata(&client->dev);
- if (!pdata)
+ if (!id->driver_data)
return -EINVAL;
if (!i2c_check_functionality(client->adapter, i2c_funcs))
return -ENOSYS;
- chip = devm_kzalloc(&client->dev,
- sizeof(struct sx150x_chip), GFP_KERNEL);
- if (!chip)
+ pctl = devm_kzalloc(dev, sizeof(*pctl), GFP_KERNEL);
+ if (!pctl)
return -ENOMEM;
- sx150x_init_chip(chip, client, id->driver_data, pdata);
- rc = sx150x_init_hw(chip, pdata);
- if (rc < 0)
- return rc;
-
- rc = devm_gpiochip_add_data(&client->dev, &chip->gpio_chip, chip);
- if (rc)
- return rc;
-
- if (pdata->irq_summary >= 0) {
- rc = sx150x_install_irq_chip(chip,
- pdata->irq_summary,
- pdata->irq_base);
- if (rc < 0)
- return rc;
+ pctl->dev = dev;
+ pctl->client = client;
+ pctl->data = (void *)id->driver_data;
+
+ mutex_init(&pctl->lock);
+
+ ret = sx150x_init_hw(pctl);
+ if (ret)
+ return ret;
+
+ /* Register GPIO controller */
+ pctl->gpio.label = devm_kstrdup(dev, client->name, GFP_KERNEL);
+ pctl->gpio.base = -1;
+ pctl->gpio.ngpio = pctl->data->npins;
+ pctl->gpio.get_direction = sx150x_gpio_get_direction;
+ pctl->gpio.direction_input = sx150x_gpio_direction_input;
+ pctl->gpio.direction_output = sx150x_gpio_direction_output;
+ pctl->gpio.get = sx150x_gpio_get;
+ pctl->gpio.set = sx150x_gpio_set;
+ pctl->gpio.set_single_ended = sx150x_gpio_set_single_ended;
+ pctl->gpio.parent = dev;
+#ifdef CONFIG_OF_GPIO
+ pctl->gpio.of_node = dev->of_node;
+#endif
+ pctl->gpio.can_sleep = true;
+
+ ret = devm_gpiochip_add_data(dev, &pctl->gpio, pctl);
+ if (ret)
+ return ret;
+
+ /* Add Interrupt support if an irq is specified */
+ if (client->irq > 0) {
+ pctl->irq_chip.name = devm_kstrdup(dev, client->name,
+ GFP_KERNEL);
+ pctl->irq_chip.irq_mask = sx150x_irq_mask;
+ pctl->irq_chip.irq_unmask = sx150x_irq_unmask;
+ pctl->irq_chip.irq_set_type = sx150x_irq_set_type;
+ pctl->irq_chip.irq_bus_lock = sx150x_irq_bus_lock;
+ pctl->irq_chip.irq_bus_sync_unlock = sx150x_irq_bus_sync_unlock;
+
+ pctl->irq.masked = ~0;
+ pctl->irq.sense = 0;
+ pctl->irq.dev_masked = ~0;
+ pctl->irq.dev_sense = 0;
+ pctl->irq.update = -1;
+
+ ret = gpiochip_irqchip_add(&pctl->gpio,
+ &pctl->irq_chip, 0,
+ handle_edge_irq, IRQ_TYPE_EDGE_BOTH);
+ if (ret) {
+ dev_err(dev, "could not connect irqchip to gpiochip\n");
+ return ret;
+ }
+
+ ret = devm_request_threaded_irq(dev, client->irq, NULL,
+ sx150x_irq_thread_fn,
+ IRQF_ONESHOT | IRQF_SHARED |
+ IRQF_TRIGGER_FALLING,
+ pctl->irq_chip.name, pctl);
+ if (ret < 0)
+ return ret;
}
- i2c_set_clientdata(client, chip);
+ /* Pinctrl_desc */
+ pctl->pinctrl_desc.name = "sx150x-pinctrl";
+ pctl->pinctrl_desc.pctlops = &sx150x_pinctrl_ops;
+ pctl->pinctrl_desc.confops = &sx150x_pinconf_ops;
+ pctl->pinctrl_desc.pins = pctl->data->pins;
+ pctl->pinctrl_desc.npins = pctl->data->npins;
+ pctl->pinctrl_desc.owner = THIS_MODULE;
+
+ pctl->pctldev = pinctrl_register(&pctl->pinctrl_desc, dev, pctl);
+ if (IS_ERR(pctl->pctldev)) {
+ dev_err(dev, "Failed to register pinctrl device\n");
+ return PTR_ERR(pctl->pctldev);
+ }
return 0;
}
static struct i2c_driver sx150x_driver = {
.driver = {
- .name = "sx150x",
+ .name = "sx150x-pinctrl",
.of_match_table = of_match_ptr(sx150x_of_match),
},
.probe = sx150x_probe,
--
1.9.1
Powered by blists - more mailing lists