Message-ID: <1478731258-26084-1-git-send-email-peda@axentia.se>
Date:   Wed, 9 Nov 2016 23:40:55 +0100
From:   Peter Rosin <peda@...ntia.se>
To:     <linux-kernel@...r.kernel.org>
CC:     Peter Rosin <peda@...ntia.se>, Liam Girdwood <lgirdwood@...il.com>,
        Mark Brown <broonie@...nel.org>,
        Rob Herring <robh+dt@...nel.org>,
        Mark Rutland <mark.rutland@....com>,
        Nicolas Ferre <nicolas.ferre@...el.com>,
        Jaroslav Kysela <perex@...ex.cz>,
        Takashi Iwai <tiwai@...e.com>, <alsa-devel@...a-project.org>,
        <devicetree@...r.kernel.org>
Subject: [PATCH v2 0/3] ASoC driver for the TSE-850

Hi!

v1 -> v2 changes:
- new subject for the bindings patch to make it easier to find
- move the driver to the sound/soc/atmel directory
- add cached values for add/loop1/loop2 to avoid gets from output gpios
- use _cansleep when updating gpios
- add comment on how the regulator voltage is mapped to the ana enum
- drop the .hw_params hook that did set the cpu dai divider and...
- ...add a preparatory patch that does this in the cpu dai driver instead
- drop .init and set the dapm routes directly in the card struct instead


The TSE-850 is an FM Transmitter Station Equipment, designed to generate
baseband signals for FM, mainly the DARC subcarrier, but other signals
are also possible.

This adds a driver for the "sound" bits of the device (quoted since it
is normally not used for normal sound output, but that works too of
course). 

I have not provided a patch to add axentia as a devicetree vendor prefix,
since such a patch is already pending in an IIO series [1] that seems
close to being accepted.

However, there are a couple of points that I'm not 100% satisfied with
for this driver.

First, I do not know how to describe the relays that control if the
IN1/IN2 signals are directly routed towards OUT1/OUT2 or if they are
routed to the "add" switch. The dapm routing treats this as if the
IN1/IN2 signals are always routed to both the "add" switch and to
the muxes feeding OUT1/OUT2. This is fine with me since nothing is
powered in those sections anyway, so what dapm thinks does not really
matter. But it is a wart all the same.

Second, there's my comment in tse850_put_mix() when the "add" switch
is updated. I believe this update should really happen as a side
effect of the call to snd_soc_dapm_mixer_update_power(), so that it
happens at the right point compared to other stuff that is powered.
But I do not know how to hook that up and instead I flip the switch
before the call since it doesn't really matter. I.e., any noise
resulting from this badness is negligeble in practice.

Cheers,
Peter

[1] http://lwn.net/Articles/705931

Peter Rosin (3):
  ASoC: atmel_ssc_dai: if not provided, default to sensible TCMR/RCMR
    periods
  ASoC: tse850: document axentia,tse850-pcm5142 bindings
  ASoC: atmel: tse850: add ASoC driver for the Axentia TSE-850

 .../bindings/sound/axentia,tse850-pcm5142.txt      |  88 ++++
 MAINTAINERS                                        |   7 +
 sound/soc/atmel/Kconfig                            |  10 +
 sound/soc/atmel/Makefile                           |   2 +
 sound/soc/atmel/atmel_ssc_dai.c                    |  29 +-
 sound/soc/atmel/atmel_ssc_dai.h                    |   1 +
 sound/soc/atmel/tse850-pcm5142.c                   | 472 +++++++++++++++++++++
 7 files changed, 603 insertions(+), 6 deletions(-)
 create mode 100644 Documentation/devicetree/bindings/sound/axentia,tse850-pcm5142.txt
 create mode 100644 sound/soc/atmel/tse850-pcm5142.c

-- 
2.1.4

Powered by blists - more mailing lists