Message-ID: <1479235095-13441-4-git-send-email-peda@axentia.se>
Date:   Tue, 15 Nov 2016 19:38:15 +0100
From:   Peter Rosin <peda@...ntia.se>
To:     <linux-kernel@...r.kernel.org>
CC:     Peter Rosin <peda@...ntia.se>, Liam Girdwood <lgirdwood@...il.com>,
        "Mark Brown" <broonie@...nel.org>,
        Rob Herring <robh+dt@...nel.org>,
        Mark Rutland <mark.rutland@....com>,
        Nicolas Ferre <nicolas.ferre@...el.com>,
        "Jaroslav Kysela" <perex@...ex.cz>, Takashi Iwai <tiwai@...e.com>,
        <alsa-devel@...a-project.org>, <devicetree@...r.kernel.org>
Subject: [PATCH v4 3/3] ASoC: atmel: tse850: add ASoC driver for the Axentia TSE-850

The TSE-850 is an FM Transmitter Station Equipment, designed to generate
baseband signals for FM, mainly the DARC subcarrier, but other signals
are also possible.

Signed-off-by: Peter Rosin <peda@...ntia.se>
---
 MAINTAINERS                      |   1 +
 sound/soc/atmel/Kconfig          |  10 +
 sound/soc/atmel/Makefile         |   2 +
 sound/soc/atmel/tse850-pcm5142.c | 472 +++++++++++++++++++++++++++++++++++++++
 4 files changed, 485 insertions(+)
 create mode 100644 sound/soc/atmel/tse850-pcm5142.c

diff --git a/MAINTAINERS b/MAINTAINERS
index e6bf00e53bf3..59baed3fd0ee 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -2323,6 +2323,7 @@ M:	Peter Rosin <peda@...ntia.se>
 L:	alsa-devel@...a-project.org (moderated for non-subscribers)
 S:	Maintained
 F:	Documentation/devicetree/bindings/sound/axentia,*
+F:	sound/soc/atmel/tse850-pcm5142.c
 
 AZ6007 DVB DRIVER
 M:	Mauro Carvalho Chehab <mchehab@...pensource.com>
diff --git a/sound/soc/atmel/Kconfig b/sound/soc/atmel/Kconfig
index 22aec9a1e9a4..4a56f3dfba51 100644
--- a/sound/soc/atmel/Kconfig
+++ b/sound/soc/atmel/Kconfig
@@ -78,4 +78,14 @@ config SND_ATMEL_SOC_PDMIC
 	help
 	  Say Y if you want to add support for Atmel ASoC driver for boards using
 	  PDMIC.
+
+config SND_ATMEL_SOC_TSE850_PCM5142
+	tristate "ASoC driver for the Axentia TSE-850"
+	depends on ARCH_AT91 && OF
+	depends on ATMEL_SSC && I2C
+	select SND_ATMEL_SOC_SSC_DMA
+	select SND_SOC_PCM512x_I2C
+	help
+	  Say Y if you want to add support for the ASoC driver for the
+	  Axentia TSE-850 with a PCM5142 codec.
 endif
diff --git a/sound/soc/atmel/Makefile b/sound/soc/atmel/Makefile
index a2b127bd9c87..67e10cbd4ed7 100644
--- a/sound/soc/atmel/Makefile
+++ b/sound/soc/atmel/Makefile
@@ -13,9 +13,11 @@ snd-atmel-soc-wm8904-objs := atmel_wm8904.o
 snd-soc-sam9x5-wm8731-objs := sam9x5_wm8731.o
 snd-atmel-soc-classd-objs := atmel-classd.o
 snd-atmel-soc-pdmic-objs := atmel-pdmic.o
+snd-atmel-soc-tse850-pcm5142-objs := tse850-pcm5142.o
 
 obj-$(CONFIG_SND_AT91_SOC_SAM9G20_WM8731) += snd-soc-sam9g20-wm8731.o
 obj-$(CONFIG_SND_ATMEL_SOC_WM8904) += snd-atmel-soc-wm8904.o
 obj-$(CONFIG_SND_AT91_SOC_SAM9X5_WM8731) += snd-soc-sam9x5-wm8731.o
 obj-$(CONFIG_SND_ATMEL_SOC_CLASSD) += snd-atmel-soc-classd.o
 obj-$(CONFIG_SND_ATMEL_SOC_PDMIC) += snd-atmel-soc-pdmic.o
+obj-$(CONFIG_SND_ATMEL_SOC_TSE850_PCM5142) += snd-atmel-soc-tse850-pcm5142.o
diff --git a/sound/soc/atmel/tse850-pcm5142.c b/sound/soc/atmel/tse850-pcm5142.c
new file mode 100644
index 000000000000..ac6a814c8ecf
--- /dev/null
+++ b/sound/soc/atmel/tse850-pcm5142.c
@@ -0,0 +1,472 @@
+/*
+ * TSE-850 audio - ASoC driver for the Axentia TSE-850 with a PCM5142 codec
+ *
+ * Copyright (C) 2016 Axentia Technologies AB
+ *
+ * Author: Peter Rosin <peda@...ntia.se>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+/*
+ *               loop1 relays
+ *   IN1 +---o  +------------+  o---+ OUT1
+ *            \                /
+ *             +              +
+ *             |   /          |
+ *             +--o  +--.     |
+ *             |  add   |     |
+ *             |        V     |
+ *             |      .---.   |
+ *   DAC +----------->|Sum|---+
+ *             |      '---'   |
+ *             |              |
+ *             +              +
+ *
+ *   IN2 +---o--+------------+--o---+ OUT2
+ *               loop2 relays
+ *
+ * The 'loop1' gpio pin controlls two relays, which are either in loop
+ * position, meaning that input and output are directly connected, or
+ * they are in mixer position, meaning that the signal is passed through
+ * the 'Sum' mixer. Similarly for 'loop2'.
+ *
+ * In the above, the 'loop1' relays are inactive, thus feeding IN1 to the
+ * mixer (if 'add' is active) and feeding the mixer output to OUT1. The
+ * 'loop2' relays are active, short-cutting the TSE-850 from channel 2.
+ * IN1, IN2, OUT1 and OUT2 are TSE-850 connectors and DAC is the PCB name
+ * of the (filtered) output from the PCM5142 codec.
+ */
+
+#include <linux/clk.h>
+#include <linux/gpio.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/of_device.h>
+#include <linux/of_gpio.h>
+#include <linux/regulator/consumer.h>
+
+#include <sound/soc.h>
+#include <sound/pcm_params.h>
+
+#include "atmel_ssc_dai.h"
+
+struct tse850_priv {
+	int ssc_id;
+
+	struct gpio_desc *add;
+	struct gpio_desc *loop1;
+	struct gpio_desc *loop2;
+
+	struct regulator *ana;
+
+	int add_cache;
+	int loop1_cache;
+	int loop2_cache;
+};
+
+static int tse850_get_mux1(struct snd_kcontrol *kctrl,
+			   struct snd_ctl_elem_value *ucontrol)
+{
+	struct snd_soc_dapm_context *dapm = snd_soc_dapm_kcontrol_dapm(kctrl);
+	struct snd_soc_card *card = dapm->card;
+	struct tse850_priv *tse850 = snd_soc_card_get_drvdata(card);
+
+	ucontrol->value.enumerated.item[0] = tse850->loop1_cache;
+
+	return 0;
+}
+
+static int tse850_put_mux1(struct snd_kcontrol *kctrl,
+			   struct snd_ctl_elem_value *ucontrol)
+{
+	struct snd_soc_dapm_context *dapm = snd_soc_dapm_kcontrol_dapm(kctrl);
+	struct snd_soc_card *card = dapm->card;
+	struct tse850_priv *tse850 = snd_soc_card_get_drvdata(card);
+	struct soc_enum *e = (struct soc_enum *)kctrl->private_value;
+	unsigned int val = ucontrol->value.enumerated.item[0];
+
+	if (val >= e->items)
+		return -EINVAL;
+
+	gpiod_set_value_cansleep(tse850->loop1, val);
+	tse850->loop1_cache = val;
+
+	return snd_soc_dapm_put_enum_double(kctrl, ucontrol);
+}
+
+static int tse850_get_mux2(struct snd_kcontrol *kctrl,
+			   struct snd_ctl_elem_value *ucontrol)
+{
+	struct snd_soc_dapm_context *dapm = snd_soc_dapm_kcontrol_dapm(kctrl);
+	struct snd_soc_card *card = dapm->card;
+	struct tse850_priv *tse850 = snd_soc_card_get_drvdata(card);
+
+	ucontrol->value.enumerated.item[0] = tse850->loop2_cache;
+
+	return 0;
+}
+
+static int tse850_put_mux2(struct snd_kcontrol *kctrl,
+			   struct snd_ctl_elem_value *ucontrol)
+{
+	struct snd_soc_dapm_context *dapm = snd_soc_dapm_kcontrol_dapm(kctrl);
+	struct snd_soc_card *card = dapm->card;
+	struct tse850_priv *tse850 = snd_soc_card_get_drvdata(card);
+	struct soc_enum *e = (struct soc_enum *)kctrl->private_value;
+	unsigned int val = ucontrol->value.enumerated.item[0];
+
+	if (val >= e->items)
+		return -EINVAL;
+
+	gpiod_set_value_cansleep(tse850->loop2, val);
+	tse850->loop2_cache = val;
+
+	return snd_soc_dapm_put_enum_double(kctrl, ucontrol);
+}
+
+int tse850_get_mix(struct snd_kcontrol *kctrl,
+		   struct snd_ctl_elem_value *ucontrol)
+{
+	struct snd_soc_dapm_context *dapm = snd_soc_dapm_kcontrol_dapm(kctrl);
+	struct snd_soc_card *card = dapm->card;
+	struct tse850_priv *tse850 = snd_soc_card_get_drvdata(card);
+
+	ucontrol->value.enumerated.item[0] = tse850->add_cache;
+
+	return 0;
+}
+
+int tse850_put_mix(struct snd_kcontrol *kctrl,
+		   struct snd_ctl_elem_value *ucontrol)
+{
+	struct snd_soc_dapm_context *dapm = snd_soc_dapm_kcontrol_dapm(kctrl);
+	struct snd_soc_card *card = dapm->card;
+	struct tse850_priv *tse850 = snd_soc_card_get_drvdata(card);
+	int connect = !!ucontrol->value.integer.value[0];
+
+	if (tse850->add_cache == connect)
+		return 0;
+
+	/*
+	 * Hmmm, this gpiod_set_value_cansleep call should probably happen
+	 * inside snd_soc_dapm_mixer_update_power in the loop.
+	 */
+	gpiod_set_value_cansleep(tse850->add, connect);
+	tse850->add_cache = connect;
+
+	snd_soc_dapm_mixer_update_power(dapm, kctrl, connect, NULL);
+	return 1;
+}
+
+int tse850_get_ana(struct snd_kcontrol *kctrl,
+		   struct snd_ctl_elem_value *ucontrol)
+{
+	struct snd_soc_dapm_context *dapm = snd_soc_dapm_kcontrol_dapm(kctrl);
+	struct snd_soc_card *card = dapm->card;
+	struct tse850_priv *tse850 = snd_soc_card_get_drvdata(card);
+	int ret;
+
+	ret = regulator_get_voltage(tse850->ana);
+	if (ret < 0)
+		return ret;
+
+	/*
+	 * Map regulator output values like so:
+	 *      -11.5V to "Low" (enum 0)
+	 * 11.5V-12.5V to "12V" (enum 1)
+	 * 12.5V-13.5V to "13V" (enum 2)
+	 *     ...
+	 * 18.5V-19.5V to "19V" (enum 8)
+	 * 19.5V-      to "20V" (enum 9)
+	 */
+	if (ret < 11000000)
+		ret = 11000000;
+	else if (ret > 20000000)
+		ret = 20000000;
+	ret -= 11000000;
+	ret = (ret + 500000) / 1000000;
+
+	ucontrol->value.enumerated.item[0] = ret;
+
+	return 0;
+}
+
+int tse850_put_ana(struct snd_kcontrol *kctrl,
+		   struct snd_ctl_elem_value *ucontrol)
+{
+	struct snd_soc_dapm_context *dapm = snd_soc_dapm_kcontrol_dapm(kctrl);
+	struct snd_soc_card *card = dapm->card;
+	struct tse850_priv *tse850 = snd_soc_card_get_drvdata(card);
+	struct soc_enum *e = (struct soc_enum *)kctrl->private_value;
+	unsigned int uV = ucontrol->value.enumerated.item[0];
+	int ret;
+
+	if (uV >= e->items)
+		return -EINVAL;
+
+	/*
+	 * Map enum zero (Low) to 2 volts on the regulator, do this since
+	 * the ana regulator is supplied by the system 12V voltage and
+	 * requesting anything below the system voltage causes the system
+	 * voltage to be passed through the regulator. Also, the ana
+	 * regulator induces noise when requesting voltages near the
+	 * system voltage. So, by mapping Low to 2V, that noise is
+	 * eliminated when all that is needed is 12V (the system voltage).
+	 */
+	if (uV)
+		uV = 11000000 + (1000000 * uV);
+	else
+		uV = 2000000;
+
+	ret = regulator_set_voltage(tse850->ana, uV, uV);
+	if (ret < 0)
+		return ret;
+
+	return snd_soc_dapm_put_enum_double(kctrl, ucontrol);
+}
+
+static const char * const mux_text[] = { "Mixer", "Loop" };
+
+static const struct soc_enum mux_enum =
+	SOC_ENUM_SINGLE(SND_SOC_NOPM, 0, 2, mux_text);
+
+static const struct snd_kcontrol_new mux1 =
+	SOC_DAPM_ENUM_EXT("MUX1", mux_enum, tse850_get_mux1, tse850_put_mux1);
+
+static const struct snd_kcontrol_new mux2 =
+	SOC_DAPM_ENUM_EXT("MUX2", mux_enum, tse850_get_mux2, tse850_put_mux2);
+
+#define TSE850_DAPM_SINGLE_EXT(xname, reg, shift, max, invert, xget, xput) \
+{	.iface = SNDRV_CTL_ELEM_IFACE_MIXER, .name = xname, \
+	.info = snd_soc_info_volsw, \
+	.get = xget, \
+	.put = xput, \
+	.private_value = SOC_SINGLE_VALUE(reg, shift, max, invert, 0) }
+
+static const struct snd_kcontrol_new mix[] = {
+	TSE850_DAPM_SINGLE_EXT("IN Switch", SND_SOC_NOPM, 0, 1, 0,
+			       tse850_get_mix, tse850_put_mix),
+};
+
+static const char * const ana_text[] = {
+	"Low", "12V", "13V", "14V", "15V", "16V", "17V", "18V", "19V", "20V"
+};
+
+static const struct soc_enum ana_enum =
+	SOC_ENUM_SINGLE(SND_SOC_NOPM, 0, 9, ana_text);
+
+static const struct snd_kcontrol_new out =
+	SOC_DAPM_ENUM_EXT("ANA", ana_enum, tse850_get_ana, tse850_put_ana);
+
+static const struct snd_soc_dapm_widget tse850_dapm_widgets[] = {
+	SND_SOC_DAPM_LINE("OUT1", NULL),
+	SND_SOC_DAPM_LINE("OUT2", NULL),
+	SND_SOC_DAPM_LINE("IN1", NULL),
+	SND_SOC_DAPM_LINE("IN2", NULL),
+	SND_SOC_DAPM_INPUT("DAC"),
+	SND_SOC_DAPM_AIF_IN("AIFINL", "Playback", 0, SND_SOC_NOPM, 0, 0),
+	SND_SOC_DAPM_AIF_IN("AIFINR", "Playback", 1, SND_SOC_NOPM, 0, 0),
+	SOC_MIXER_ARRAY("MIX", SND_SOC_NOPM, 0, 0, mix),
+	SND_SOC_DAPM_MUX("MUX1", SND_SOC_NOPM, 0, 0, &mux1),
+	SND_SOC_DAPM_MUX("MUX2", SND_SOC_NOPM, 0, 0, &mux2),
+	SND_SOC_DAPM_OUT_DRV("OUT", SND_SOC_NOPM, 0, 0, &out, 1),
+};
+
+/*
+ * These connections are not entirely correct, since both IN1 and IN2
+ * are always fed to MIX (if the "IN switch" is set so), i.e. without
+ * regard to the loop1 and loop2 relays that according to this only
+ * control MUX1 and MUX2 but in fact also control how the input signals
+ * are routed.
+ * But, 1) I don't know how to do it right, and 2) it doesn't seem to
+ * matter in practice since nothing is powered in those sections anyway.
+ */
+static const struct snd_soc_dapm_route tse850_intercon[] = {
+	{ "OUT1", NULL, "MUX1" },
+	{ "OUT2", NULL, "MUX2" },
+
+	{ "MUX1", "Loop",  "IN1" },
+	{ "MUX1", "Mixer", "OUT" },
+
+	{ "MUX2", "Loop",  "IN2" },
+	{ "MUX2", "Mixer", "OUT" },
+
+	{ "OUT", NULL, "MIX" },
+
+	{ "MIX", NULL, "DAC" },
+	{ "MIX", "IN Switch", "IN1" },
+	{ "MIX", "IN Switch", "IN2" },
+
+	/* connect board input to the codec left channel output pin */
+	{ "DAC", NULL, "OUTL" },
+};
+
+static struct snd_soc_dai_link tse850_dailink = {
+	.name = "TSE-850",
+	.stream_name = "TSE-850-PCM",
+	.codec_dai_name = "pcm512x-hifi",
+	.dai_fmt = SND_SOC_DAIFMT_I2S
+		 | SND_SOC_DAIFMT_NB_NF
+		 | SND_SOC_DAIFMT_CBM_CFS,
+};
+
+static struct snd_soc_card tse850_card = {
+	.name = "TSE-850-ASoC",
+	.owner = THIS_MODULE,
+	.dai_link = &tse850_dailink,
+	.num_links = 1,
+	.dapm_widgets = tse850_dapm_widgets,
+	.num_dapm_widgets = ARRAY_SIZE(tse850_dapm_widgets),
+	.dapm_routes = tse850_intercon,
+	.num_dapm_routes = ARRAY_SIZE(tse850_intercon),
+	.fully_routed = true,
+};
+
+static int tse850_dt_init(struct platform_device *pdev)
+{
+	struct device_node *np = pdev->dev.of_node;
+	struct device_node *codec_np, *cpu_np;
+	struct snd_soc_card *card = &tse850_card;
+	struct snd_soc_dai_link *dailink = &tse850_dailink;
+	struct tse850_priv *tse850 = snd_soc_card_get_drvdata(card);
+
+	if (!np) {
+		dev_err(&pdev->dev, "only device tree supported\n");
+		return -EINVAL;
+	}
+
+	cpu_np = of_parse_phandle(np, "axentia,ssc-controller", 0);
+	if (!cpu_np) {
+		dev_err(&pdev->dev, "failed to get dai and pcm info\n");
+		return -EINVAL;
+	}
+	dailink->cpu_of_node = cpu_np;
+	dailink->platform_of_node = cpu_np;
+	tse850->ssc_id = of_alias_get_id(cpu_np, "ssc");
+	of_node_put(cpu_np);
+
+	codec_np = of_parse_phandle(np, "axentia,audio-codec", 0);
+	if (!codec_np) {
+		dev_err(&pdev->dev, "failed to get codec info\n");
+		return -EINVAL;
+	}
+	dailink->codec_of_node = codec_np;
+	of_node_put(codec_np);
+
+	return 0;
+}
+
+static int tse850_probe(struct platform_device *pdev)
+{
+	struct snd_soc_card *card = &tse850_card;
+	struct device *dev = card->dev = &pdev->dev;
+	struct tse850_priv *tse850;
+	int ret;
+
+	tse850 = devm_kzalloc(dev, sizeof(*tse850), GFP_KERNEL);
+	if (!tse850)
+		return -ENOMEM;
+
+	snd_soc_card_set_drvdata(card, tse850);
+
+	ret = tse850_dt_init(pdev);
+	if (ret) {
+		dev_err(dev, "failed to init dt info\n");
+		return ret;
+	}
+
+	tse850->add = devm_gpiod_get(dev, "axentia,add", GPIOD_OUT_HIGH);
+	if (IS_ERR(tse850->add)) {
+		if (PTR_ERR(tse850->add) != -EPROBE_DEFER)
+			dev_err(dev, "failed to get 'add' gpio\n");
+		return PTR_ERR(tse850->add);
+	}
+	tse850->add_cache = 1;
+
+	tse850->loop1 = devm_gpiod_get(dev, "axentia,loop1", GPIOD_OUT_HIGH);
+	if (IS_ERR(tse850->loop1)) {
+		if (PTR_ERR(tse850->loop1) != -EPROBE_DEFER)
+			dev_err(dev, "failed to get 'loop1' gpio\n");
+		return PTR_ERR(tse850->loop1);
+	}
+	tse850->loop1_cache = 1;
+
+	tse850->loop2 = devm_gpiod_get(dev, "axentia,loop2", GPIOD_OUT_HIGH);
+	if (IS_ERR(tse850->loop2)) {
+		if (PTR_ERR(tse850->loop2) != -EPROBE_DEFER)
+			dev_err(dev, "failed to get 'loop2' gpio\n");
+		return PTR_ERR(tse850->loop2);
+	}
+	tse850->loop2_cache = 1;
+
+	tse850->ana = devm_regulator_get(dev, "axentia,ana");
+	if (IS_ERR(tse850->ana)) {
+		if (PTR_ERR(tse850->ana) != -EPROBE_DEFER)
+			dev_err(dev, "failed to get 'ana' regulator\n");
+		return PTR_ERR(tse850->ana);
+	}
+
+	ret = regulator_enable(tse850->ana);
+	if (ret < 0) {
+		dev_err(dev, "failed to enable the 'ana' regulator\n");
+		return ret;
+	}
+
+	ret = atmel_ssc_set_audio(tse850->ssc_id);
+	if (ret != 0) {
+		dev_err(dev,
+			"failed to set SSC %d for audio\n", tse850->ssc_id);
+		goto err_disable_ana;
+	}
+
+	ret = snd_soc_register_card(card);
+	if (ret) {
+		dev_err(dev, "snd_soc_register_card failed\n");
+		goto err_put_audio;
+	}
+
+	return 0;
+
+err_put_audio:
+	atmel_ssc_put_audio(tse850->ssc_id);
+err_disable_ana:
+	regulator_disable(tse850->ana);
+	return ret;
+}
+
+static int tse850_remove(struct platform_device *pdev)
+{
+	struct snd_soc_card *card = platform_get_drvdata(pdev);
+	struct tse850_priv *tse850 = snd_soc_card_get_drvdata(card);
+
+	snd_soc_unregister_card(card);
+	atmel_ssc_put_audio(tse850->ssc_id);
+	regulator_disable(tse850->ana);
+
+	return 0;
+}
+
+static const struct of_device_id tse850_dt_ids[] = {
+	{ .compatible = "axentia,tse850-pcm5142", },
+	{ /* sentinel */ }
+};
+MODULE_DEVICE_TABLE(of, tse850_dt_ids);
+
+static struct platform_driver tse850_driver = {
+	.driver = {
+		.name = "axentia-tse850-pcm5142",
+		.of_match_table = of_match_ptr(tse850_dt_ids),
+	},
+	.probe = tse850_probe,
+	.remove = tse850_remove,
+};
+
+module_platform_driver(tse850_driver);
+
+/* Module information */
+MODULE_AUTHOR("Peter Rosin <peda@...ntia.se>");
+MODULE_DESCRIPTION("ALSA SoC driver for TSE-850 with PCM5142 codec");
+MODULE_LICENSE("GPL");
-- 
2.1.4

Powered by blists - more mailing lists