| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-Id: <89c95d0084da6ad7132caa54ca66eb619d8a5090.1484154449.git-series.gregory.clement@free-electrons.com>
Date: Wed, 11 Jan 2017 18:19:08 +0100
From: Gregory CLEMENT <gregory.clement@...e-electrons.com>
To: Ulf Hansson <ulf.hansson@...aro.org>,
Adrian Hunter <adrian.hunter@...el.com>,
linux-mmc@...r.kernel.org
Cc: Jason Cooper <jason@...edaemon.net>, Andrew Lunn <andrew@...n.ch>,
Sebastian Hesselbarth <sebastian.hesselbarth@...il.com>,
Gregory CLEMENT <gregory.clement@...e-electrons.com>,
Thomas Petazzoni <thomas.petazzoni@...e-electrons.com>,
linux-arm-kernel@...ts.infradead.org,
Mike Turquette <mturquette@...libre.com>,
Stephen Boyd <sboyd@...eaurora.org>, linux-clk@...r.kernel.org,
linux-kernel@...r.kernel.org, Rob Herring <robh+dt@...nel.org>,
devicetree@...r.kernel.org, Ziji Hu <huziji@...vell.com>,
Jimmy Xu <zmxu@...vell.com>,
Jisheng Zhang <jszhang@...vell.com>,
Nadav Haklai <nadavh@...vell.com>, Ryan Gao <ygao@...vell.com>,
Doug Jones <dougj@...vell.com>, Victor Gu <xigu@...vell.com>,
"Wei(SOCP) Liu" <liuw@...vell.com>,
Wilson Ding <dingwei@...vell.com>,
Yehuda Yitschak <yehuday@...vell.com>,
Marcin Wojtas <mw@...ihalf.com>,
Hanna Hawa <hannah@...vell.com>,
Kostya Porotchkin <kostap@...vell.com>
Subject: [PATCH v5 05/12] dt: bindings: Add bindings for Marvell Xenon SD Host Controller
From: Hu Ziji <huziji@...vell.com>
Marvell Xenon SDHC can support eMMC/SD/SDIO.
Add Xenon-specific properties.
Also add properties for Xenon PHY setting.
Signed-off-by: Hu Ziji <huziji@...vell.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@...e-electrons.com>
---
Documentation/devicetree/bindings/mmc/marvell,xenon-sdhci.txt | 197 +++++++-
1 file changed, 197 insertions(+)
create mode 100644 Documentation/devicetree/bindings/mmc/marvell,xenon-sdhci.txt
diff --git a/Documentation/devicetree/bindings/mmc/marvell,xenon-sdhci.txt b/Documentation/devicetree/bindings/mmc/marvell,xenon-sdhci.txt
new file mode 100644
index 000000000000..a3876d2cc616
--- /dev/null
+++ b/Documentation/devicetree/bindings/mmc/marvell,xenon-sdhci.txt
@@ -0,0 +1,197 @@
+Marvell Xenon SDHCI Controller device tree bindings
+This file documents differences between the core mmc properties
+described by mmc.txt and the properties used by the Xenon implementation.
+
+Multiple SDHCs might be put into a single Xenon IP, to save size and cost.
+Each SDHC is independent and owns independent resources, such as register sets,
+clock and PHY.
+Each SDHC should have an independent device tree node.
+
+Required Properties:
+- compatible: should be one of the following
+ - "marvell,armada-3700-sdhci": For controllers on Armada-3700 SoC.
+ Must provide a second register area and marvell,pad-type.
+ - "marvell,armada-8k-sdhci": For controllers on Armada 7K/8K SoC
+
+- clocks:
+ Array of clocks required for SDHC.
+ Require at least input clock for Xenon IP core.
+
+- clock-names:
+ Array of names corresponding to clocks property.
+ The input clock for Xenon IP core should be named as "core".
+
+- reg:
+ * For "marvell,armada-3700-sdhci", two register areas.
+ The first one for Xenon IP register. The second one for the Armada 3700 SoC
+ PHY PAD Voltage Control register.
+ Please follow the examples with compatible "marvell,armada-3700-sdhci"
+ in below.
+ Please also check property marvell,pad-type in below.
+
+ * For other compatible strings, one register area for Xenon IP.
+
+Optional Properties:
+- mmccard:
+ mmccard child node must be provided when current SDHC is for eMMC.
+ Xenon SDHC often can support both SD and eMMC. This child node indicates that
+ current SDHC is for eMMC card. Thus Xenon eMMC specific configuration and
+ operations can be enabled prior to eMMC init sequence.
+ Please refer to Documentation/devicetree/bindings/mmc/mmc-card.txt.
+ This child node should not be set if current Xenon SDHC is for SD/SDIO.
+
+- bus-width:
+ When 8-bit data bus width is in use for eMMC, this property should be
+ explicitly provided and set as 8.
+ It is optional when data bus width is 4-bit or 1-bit.
+
+- mmc-ddr-1_8v:
+ Select this property when eMMC HS DDR is supported on SDHC side.
+
+- mmc-hs400-1_8v:
+ Select this property when eMMC HS400 is supported on SDHC side.
+
+- no-1-8-v:
+ Select this property when 1.8V signaling voltage supply is unavailable.
+ When this property is enabled, both mmc-ddr-1_8v and mmc-hs400-1_8v should be
+ cleared.
+
+- marvell,xenon-sdhc-id:
+ Indicate the corresponding bit index of current SDHC in
+ SDHC System Operation Control Register Bit[7:0].
+ Set/clear the corresponding bit to enable/disable current SDHC.
+ If Xenon IP contains only one SDHC, this property is optional.
+
+- marvell,xenon-phy-type:
+ Xenon support mutilple types of PHYs.
+ To select eMMC 5.1 PHY, set:
+ marvell,xenon-phy-type = "emmc 5.1 phy"
+ eMMC 5.1 PHY is the default choice if this property is not provided.
+ To select eMMC 5.0 PHY, set:
+ marvell,xenon-phy-type = "emmc 5.0 phy"
+
+ All those types of PHYs can support eMMC, SD and SDIO.
+ Please note that this property only presents the type of PHY.
+ It doesn't stand for the entire SDHC type or property.
+ For example, "emmc 5.1 phy" doesn't mean that this Xenon SDHC only supports
+ eMMC 5.1.
+
+- marvell,xenon-phy-znr:
+ Set PHY ZNR value.
+ Only available for eMMC PHY 5.1 and eMMC PHY 5.0.
+ Valid range = [0:0x1F].
+ ZNR is set as 0xF by default if this property is not provided.
+
+- marvell,xenon-phy-zpr:
+ Set PHY ZPR value.
+ Only available for eMMC PHY 5.1 and eMMC PHY 5.0.
+ Valid range = [0:0x1F].
+ ZPR is set as 0xF by default if this property is not provided.
+
+- marvell,xenon-phy-nr-success-tun:
+ Set the number of required consecutive successful sampling points used to
+ identify a valid sampling window, in tuning process.
+ Valid range = [1:7].
+ Set as 0x4 by default if this property is not provided.
+
+- marvell,xenon-phy-tun-step-divider:
+ Set the divider for calculating TUN_STEP.
+ Set as 64 by default if this property is not provided.
+
+- marvell,xenon-phy-slow-mode:
+ If this property is selected, transfers will bypass PHY.
+ Only available when bus frequency lower than 55MHz in SDR mde.
+ Disabled by default. Please only try this property if timing issues always
+ occur with PHY enabled in eMMC HS SDR, SD SDR12, SD SDR25, SD SDR50 mode.
+
+- marvell,xenon-tun-count:
+ Xenon SDHC SoC usually doesn't provide re-tuning counter in
+ Capabilities Register 3 Bit[11:8].
+ This property provides the re-tuning counter.
+ If this property is not set, default re-tuning counter will
+ be set as 0x9 in driver.
+
+- marvell,pad-type:
+ Type of Armada 3700 SoC PHY PAD Voltage Controller register.
+ Only valid when "marvell,armada-3700-sdhci" is selected.
+ Two types: "sd" and "fixed-1-8v".
+ If "sd" is slected, SoC PHY PAD is set as 3.3V at the beginning and is
+ switched to 1.8V when SD in UHS-I.
+ If "fixed-1-8v" is slected, SoC PHY PAD is fixed 1.8V, such as for eMMC.
+ Please follow the examples with compatible "marvell,armada-3700-sdhci"
+ in below.
+
+Example:
+- For eMMC:
+
+ sdhci@...000 {
+ compatible = "marvell,armada-8k-sdhci";
+ reg = <0xaa0000 0x1000>;
+ interrupts = <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>
+ clocks = <&emmc_clk>;
+ clock-names = "core";
+ bus-width = <8>;
+ mmc-ddr-1_8v;
+ mmc-hs400-1_8v;
+ marvell,xenon-sdhc-id = <0>;
+ marvell,xenon-phy-type = "emmc 5.1 phy";
+ marvell,xenon-tun-count = <11>;
+
+ #address-cells = <1>;
+ #size-cells = <0>;
+ mmccard: mmccard@0 {
+ compatible = "mmc-card";
+ reg = <0>;
+ };
+ };
+
+- For SD/SDIO:
+
+ sdhci@...000 {
+ compatible = "marvell,armada-8k-sdhci";
+ reg = <0xab0000 0x1000>;
+ interrupts = <GIC_SPI 55 IRQ_TYPE_LEVEL_HIGH>
+ vqmmc-supply = <&sd_regulator>;
+ clocks = <&sdclk>;
+ clock-names = "core";
+ bus-width = <4>;
+ marvell,xenon-tun-count = <9>;
+ };
+
+- For eMMC with compatible "marvell,armada-3700-sdhci":
+
+ sdhci@...000 {
+ compatible = "marvell,armada-3700-sdhci";
+ reg = <0xaa0000 0x1000>,
+ <phy_addr 0x4>;
+ interrupts = <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>
+ clocks = <&emmcclk>;
+ clock-names = "core";
+ bus-width = <8>;
+ mmc-ddr-1_8v;
+ mmc-hs400-1_8v;
+
+ marvell,pad-type = "fixed-1-8v";
+
+ #address-cells = <1>;
+ #size-cells = <0>;
+ mmccard: mmccard@0 {
+ compatible = "mmc-card";
+ reg = <0>;
+ };
+ };
+
+- For SD/SDIO with compatible "marvell,armada-3700-sdhci":
+
+ sdhci@...000 {
+ compatible = "marvell,armada-3700-sdhci";
+ reg = <0xab0000 0x1000>,
+ <phy_addr 0x4>;
+ interrupts = <GIC_SPI 55 IRQ_TYPE_LEVEL_HIGH>
+ vqmmc-supply = <&sd_regulator>;
+ clocks = <&sdclk>;
+ clock-names = "core";
+ bus-width = <4>;
+
+ marvell,pad-type = "sd";
+ };
--
git-series 0.9.1
Powered by blists - more mailing lists