| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-Id: <1484253167-27568-1-git-send-email-david@lechnology.com>
Date: Thu, 12 Jan 2017 14:32:47 -0600
From: David Lechner <david@...hnology.com>
To: devicetree@...r.kernel.org, linux-arm-kernel@...ts.infradead.org
Cc: David Lechner <david@...hnology.com>, Sekhar Nori <nsekhar@...com>,
Kevin Hilman <khilman@...nel.org>,
Rob Herring <robh+dt@...nel.org>,
Mark Rutland <mark.rutland@....com>,
linux-kernel@...r.kernel.org
Subject: [PATCH v3] ARM: dts: Add LEGO MINDSTORMS EV3 dts
This adds a device tree definition file for LEGO MINDSTORMS EV3.
What is working:
* Pin muxing
* Pinconf
* GPIOs
* MicroSD card reader
* UART on input port 1
* Buttons
* LEDs
* Poweroff/reset
* Flash memory
* EEPROM
* USB host port
* USB peripheral port
What is not working/to be added later:
* Speaker - have patch submitted to get pwm-beeper working - maybe someday
it will have a real sound driver that uses PRU
* A/DC chip - have driver submitted and accepted - waiting for ack on
device tree bindings
* Display - waiting for "simple DRM" to be mainlined
* Bluetooth - needs new driver for sequencing power/enable/clock
* Input and output ports - need some sort of new phy or extcon driver as
well as PRU UART and PRU I2C drivers
* Battery indication - needs new power supply driver
Note on flash partitions:
These partitions are based on the official EV3 firmware from LEGO. It is
expected that most users of the mainline kernel on EV3 will be booting from
an SD card while retaining the official firmware in the flash memory.
Furthermore, the official firmware uses an ancient U-Boot (2009) that has
no device tree support. So, it makes sense to have this partition table in
the EV3 device tree file. In the unlikely case that anyone does create their
own firmware image with different partitioning, they can use a modern
U-Boot in their own firmware image that modifies the device tree with the
custom partitions.
Signed-off-by: David Lechner <david@...hnology.com>
---
v3 changes:
* required defconfig patches have been picked up in linux-davinci tree, so this
is the only patch left in the series
* Added aliases node for consistent naming of serial ports
* Added memory node
* Removed nodes that are not finalized yet
* Renamed button labels to match EV3 users manual
v2 changes:
* Dropped defconfig patches that have already been pick up
* Added some new defconfig patches
* Updated device tree file based on feedback and new available bindings
* Renamed file to include da850- prefix
* Changed button labels
* Fixed LED names
* Added beeper device for sound
* Added regulators for USB and A/DC
* Removed unused pinmux nodes
* Added pinconf for buttons
* Enabled pwms
* Used preferred bindings for flash partitions
* Added A/DC spi device
* Enabled USB
arch/arm/boot/dts/Makefile | 3 +-
arch/arm/boot/dts/da850-lego-ev3.dts | 313 +++++++++++++++++++++++++++++++++++
2 files changed, 315 insertions(+), 1 deletion(-)
create mode 100644 arch/arm/boot/dts/da850-lego-ev3.dts
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index 78a94b7..1a19e7a 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -130,7 +130,8 @@ dtb-$(CONFIG_ARCH_CLPS711X) += \
dtb-$(CONFIG_ARCH_DAVINCI) += \
da850-lcdk.dtb \
da850-enbw-cmc.dtb \
- da850-evm.dtb
+ da850-evm.dtb \
+ da850-lego-ev3.dtb
dtb-$(CONFIG_ARCH_DIGICOLOR) += \
cx92755_equinox.dtb
dtb-$(CONFIG_ARCH_EFM32) += \
diff --git a/arch/arm/boot/dts/da850-lego-ev3.dts b/arch/arm/boot/dts/da850-lego-ev3.dts
new file mode 100644
index 0000000..7aaf902
--- /dev/null
+++ b/arch/arm/boot/dts/da850-lego-ev3.dts
@@ -0,0 +1,313 @@
+/*
+ * Device tree for LEGO MINDSTORMS EV3
+ *
+ * Copyright (C) 2017 David Lechner <david@...hnology.com>
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License as published by the
+ * Free Software Foundation, version 2.
+ */
+
+/dts-v1/;
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/linux-event-codes.h>
+#include <dt-bindings/pwm/pwm.h>
+
+#include "da850.dtsi"
+
+/ {
+ compatible = "lego,ev3", "ti,da850";
+ model = "LEGO MINDSTORMS EV3";
+
+ aliases {
+ serial1 = &serial1;
+ };
+
+ memory@...00000 {
+ device_type = "memory";
+ reg = <0xc0000000 0x04000000>;
+ };
+
+ /*
+ * The buttons on the EV3 are mapped to keyboard keys.
+ */
+ gpio_keys {
+ compatible = "gpio-keys";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ label = "EV3 Brick Buttons";
+ pinctrl-names = "default";
+ pinctrl-0 = <&button_pins>, <&button_bias>;
+
+ center {
+ label = "Center";
+ linux,code = <KEY_ENTER>;
+ gpios = <&gpio 29 GPIO_ACTIVE_HIGH>;
+ };
+
+ left {
+ label = "Left";
+ linux,code = <KEY_LEFT>;
+ gpios = <&gpio 102 GPIO_ACTIVE_HIGH>;
+ };
+
+ back {
+ label = "Back";
+ linux,code = <KEY_BACKSPACE>;
+ gpios = <&gpio 106 GPIO_ACTIVE_HIGH>;
+ };
+
+ right {
+ label = "Right";
+ linux,code = <KEY_RIGHT>;
+ gpios = <&gpio 124 GPIO_ACTIVE_HIGH>;
+ };
+
+ down {
+ label = "Down";
+ linux,code = <KEY_DOWN>;
+ gpios = <&gpio 126 GPIO_ACTIVE_HIGH>;
+ };
+
+ up {
+ label = "Up";
+ linux,code = <KEY_UP>;
+ gpios = <&gpio 127 GPIO_ACTIVE_HIGH>;
+ };
+ };
+
+ /*
+ * The EV3 has two built-in bi-color LEDs behind the buttons.
+ */
+ leds {
+ compatible = "gpio-leds";
+ pinctrl-names = "default";
+ pinctrl-0 = <&led_pins>;
+
+ left_green {
+ label = "led0:green:brick-status";
+ /* GP6[13] */
+ gpios = <&gpio 103 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "default-on";
+ };
+
+ right_red {
+ label = "led1:red:brick-status";
+ /* GP6[7] */
+ gpios = <&gpio 108 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "default-on";
+ };
+
+ left_red {
+ label = "led0:red:brick-status";
+ /* GP6[12] */
+ gpios = <&gpio 109 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "default-on";
+ };
+
+ right_green {
+ label = "led1:green:brick-status";
+ /* GP6[14] */
+ gpios = <&gpio 110 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "default-on";
+ };
+ };
+
+ /*
+ * The EV3 is powered down by turning off the main 5V supply.
+ */
+ gpio-poweroff {
+ compatible = "gpio-poweroff";
+ gpios = <&gpio 107 GPIO_ACTIVE_LOW>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&system_power_pin>;
+ };
+
+ /*
+ * This is a 5V current limiting regulator that is shared by USB,
+ * the sensor (input) ports, the motor (output) ports and the A/DC.
+ */
+ vcc5v: regulator1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&vcc5v_pins>;
+ compatible = "regulator-fixed";
+ regulator-name = "vcc5v";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ gpio = <&gpio 101 0>;
+ over-current-gpios = <&gpio 99 GPIO_ACTIVE_LOW>;
+ enable-active-high;
+ regulator-boot-on;
+ };
+};
+
+&pmx_core {
+ status = "okay";
+
+ spi0_cs3_pin: pinmux_spi0_cs3_pin {
+ pinctrl-single,bits = <
+ /* CS3 */
+ 0xc 0x01000000 0x0f000000
+ >;
+ };
+
+ mmc0_cd_pin: pinmux_mmc0_cd {
+ pinctrl-single,bits = <
+ /* GP5[14] */
+ 0x2C 0x00000080 0x000000f0
+ >;
+ };
+
+ button_pins: pinmux_button_pins {
+ pinctrl-single,bits = <
+ /* GP1[13] */
+ 0x8 0x00000800 0x00000f00
+ /* GP6[10] */
+ 0x34 0x00800000 0x00f00000
+ /* GP6[6] */
+ 0x38 0x00000080 0x000000f0
+ /* GP7[12], GP7[14], GP7[15] */
+ 0x40 0x00808800 0x00f0ff00
+ >;
+ };
+
+ led_pins: pinmux_led_pins {
+ pinctrl-single,bits = <
+ /* GP6[12], GP6[13], GP6[14] */
+ 0x34 0x00008880 0x0000fff0
+ /* GP6[7] */
+ 0x38 0x00000008 0x0000000f
+ >;
+ };
+
+ system_power_pin: pinmux_system_power {
+ pinctrl-single,bits = <
+ /* GP6[11] */
+ 0x34 0x00080000 0x000f0000
+ >;
+ };
+
+ vcc5v_pins: pinmux_vcc5v {
+ pinctrl-single,bits = <
+ /* GP6[5] */
+ 0x40 0x00000080 0x000000f0
+ /* GP6[3] */
+ 0x4c 0x00008000 0x0000f000
+ >;
+ };
+};
+
+&pinconf {
+ status = "okay";
+
+ /* Buttons have external pulldown resistors */
+ button_bias: button-bias-groups {
+ disable {
+ groups = "cp5", "cp24", "cp25", "cp28";
+ bias-disable;
+ };
+ };
+};
+
+/* Input port 1 */
+&serial1 {
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&serial1_rxtx_pins>;
+};
+
+&rtc0 {
+ status = "okay";
+};
+
+&i2c0 {
+ status = "okay";
+ clock-frequency = <400000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c0_pins>;
+
+ /*
+ * EEPROM contains the first stage bootloader, HW ID and Bluetooth MAC.
+ */
+ eeprom@50 {
+ compatible = "at24,24c128";
+ pagesize = <64>;
+ read-only;
+ reg = <0x50>;
+ };
+};
+
+&wdt {
+ status = "okay";
+};
+
+&mmc0 {
+ status = "okay";
+ max-frequency = <50000000>;
+ bus-width = <4>;
+ cd-gpios = <&gpio 94 GPIO_ACTIVE_LOW>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc0_pins>, <&mmc0_cd_pin>;
+};
+
+&spi0 {
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&spi0_pins>, <&spi0_cs0_pin>, <&spi0_cs3_pin>;
+
+ flash@0 {
+ compatible = "n25q128a13", "jedec,spi-nor";
+ reg = <0>;
+ spi-max-frequency = <50000000>;
+ ti,spi-wdelay = <8>;
+
+ /* Partitions are based on the official firmware from LEGO */
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ partition@0 {
+ label = "U-Boot";
+ reg = <0 0x40000>;
+ };
+
+ partition@...00 {
+ label = "U-Boot Env";
+ reg = <0x40000 0x10000>;
+ };
+
+ partition@...00 {
+ label = "Kernel";
+ reg = <0x50000 0x200000>;
+ };
+
+ partition@...000 {
+ label = "Filesystem";
+ reg = <0x250000 0xa50000>;
+ };
+
+ partition@...000 {
+ label = "Storage";
+ reg = <0xcb0000 0x2f0000>;
+ };
+ };
+ };
+};
+
+&gpio {
+ status = "okay";
+};
+
+&usb_phy {
+ status = "okay";
+};
+
+&usb0 {
+ status = "okay";
+};
+
+&usb1 {
+ status = "okay";
+ vbus-supply = <&vcc5v>;
+};
--
2.7.4
Powered by blists - more mailing lists