| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-ID: <2b8672bc-58ae-66a9-46d7-c7f3c5825a9d@arm.com>
Date: Mon, 30 Jan 2017 01:42:40 +0000
From: André Przywara <andre.przywara@....com>
To: Icenowy Zheng <icenowy@...c.xyz>,
Maxime Ripard <maxime.ripard@...e-electrons.com>,
Chen-Yu Tsai <wens@...e.org>,
Linus Walleij <linus.walleij@...aro.org>,
Vinod Koul <vinod.koul@...el.com>,
Mark Brown <broonie@...nel.org>,
Jaroslav Kysela <perex@...ex.cz>
Cc: linux-clk@...r.kernel.org, devicetree@...r.kernel.org,
linux-arm-kernel@...ts.infradead.org, linux-kernel@...r.kernel.org,
linux-gpio@...r.kernel.org, dmaengine@...r.kernel.org,
alsa-devel@...a-project.org, linux-sunxi@...glegroups.com,
Rob Herring <robh+dt@...nel.org>,
Mark Rutland <Mark.Rutland@....com>,
"devicetree@...r.kernel.org" <devicetree@...r.kernel.org>
Subject: Re: [PATCH v3 05/10] arm: dts: sun8i: split Allwinner H3 .dtsi
On 29/01/17 02:33, Icenowy Zheng wrote:
> From: Andre Przywara <andre.przywara@....com>
(Adding DT folks to CC:)
see below ...
> The new Allwinner H5 SoC is pin-compatible to the H3 SoC, but with the
> Cortex-A7 cores replaced by Cortex-A53 cores and the MMC controller
> updated. So we should really share almost the whole .dtsi.
> In preparation for that move the peripheral parts of the existing
> sun8i-h3.dtsi into a new sun8i-h3-h5.dtsi.
> The actual sun8i-h3.dtsi then includes that and defines the H3 specific
> parts on top of it.
> On the way get rid of skeleton.dtsi, as recommended in that very file.
>
> Signed-off-by: Andre Przywara <andre.przywara@....com>
> [Icenowy: also split out mmc, as well as pio and ccu's compatible]
> Signed-off-by: Icenowy Zheng <icenowy@...c.xyz>
> ---
> Changes in v3:
> - Use label-based syntax to reference nodes in H3 DTSI file.
> Changes in v2:
> - Rebase on current linux-next (because of the add of audio codec)
>
> arch/arm/boot/dts/sun8i-h3.dtsi | 571 +++----------------------------------
> arch/arm/boot/dts/sunxi-h3-h5.dtsi | 557 ++++++++++++++++++++++++++++++++++++
> 2 files changed, 598 insertions(+), 530 deletions(-)
> create mode 100644 arch/arm/boot/dts/sunxi-h3-h5.dtsi
>
> diff --git a/arch/arm/boot/dts/sun8i-h3.dtsi b/arch/arm/boot/dts/sun8i-h3.dtsi
> index 08fd0860bb6b..f3a3033789b9 100644
> --- a/arch/arm/boot/dts/sun8i-h3.dtsi
> +++ b/arch/arm/boot/dts/sun8i-h3.dtsi
> @@ -40,12 +40,7 @@
> * OTHER DEALINGS IN THE SOFTWARE.
> */
>
> -#include "skeleton.dtsi"
> -
> -#include <dt-bindings/clock/sun8i-h3-ccu.h>
> -#include <dt-bindings/interrupt-controller/arm-gic.h>
> -#include <dt-bindings/pinctrl/sun4i-a10.h>
> -#include <dt-bindings/reset/sun8i-h3-ccu.h>
> +#include "sunxi-h3-h5.dtsi"
>
> / {
> interrupt-parent = <&gic>;
> @@ -87,489 +82,7 @@
> <GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>;
> };
>
> - clocks {
> - #address-cells = <1>;
> - #size-cells = <1>;
> - ranges;
> -
> - osc24M: osc24M_clk {
> - #clock-cells = <0>;
> - compatible = "fixed-clock";
> - clock-frequency = <24000000>;
> - clock-output-names = "osc24M";
> - };
> -
> - osc32k: osc32k_clk {
> - #clock-cells = <0>;
> - compatible = "fixed-clock";
> - clock-frequency = <32768>;
> - clock-output-names = "osc32k";
> - };
> -
> - apb0: apb0_clk {
> - compatible = "fixed-factor-clock";
> - #clock-cells = <0>;
> - clock-div = <1>;
> - clock-mult = <1>;
> - clocks = <&osc24M>;
> - clock-output-names = "apb0";
> - };
> -
> - apb0_gates: clk@...01428 {
> - compatible = "allwinner,sun8i-h3-apb0-gates-clk",
> - "allwinner,sun4i-a10-gates-clk";
> - reg = <0x01f01428 0x4>;
> - #clock-cells = <1>;
> - clocks = <&apb0>;
> - clock-indices = <0>, <1>;
> - clock-output-names = "apb0_pio", "apb0_ir";
> - };
> -
> - ir_clk: ir_clk@...01454 {
> - compatible = "allwinner,sun4i-a10-mod0-clk";
> - reg = <0x01f01454 0x4>;
> - #clock-cells = <0>;
> - clocks = <&osc32k>, <&osc24M>;
> - clock-output-names = "ir";
> - };
> - };
> -
> soc {
> - compatible = "simple-bus";
> - #address-cells = <1>;
> - #size-cells = <1>;
> - ranges;
> -
> - dma: dma-controller@...02000 {
> - compatible = "allwinner,sun8i-h3-dma";
> - reg = <0x01c02000 0x1000>;
> - interrupts = <GIC_SPI 50 IRQ_TYPE_LEVEL_HIGH>;
> - clocks = <&ccu CLK_BUS_DMA>;
> - resets = <&ccu RST_BUS_DMA>;
> - #dma-cells = <1>;
> - };
> -
> - mmc0: mmc@...0f000 {
> - compatible = "allwinner,sun7i-a20-mmc";
> - reg = <0x01c0f000 0x1000>;
> - clocks = <&ccu CLK_BUS_MMC0>,
> - <&ccu CLK_MMC0>,
> - <&ccu CLK_MMC0_OUTPUT>,
> - <&ccu CLK_MMC0_SAMPLE>;
> - clock-names = "ahb",
> - "mmc",
> - "output",
> - "sample";
> - resets = <&ccu RST_BUS_MMC0>;
> - reset-names = "ahb";
> - interrupts = <GIC_SPI 60 IRQ_TYPE_LEVEL_HIGH>;
> - status = "disabled";
> - #address-cells = <1>;
> - #size-cells = <0>;
> - };
> -
> - mmc1: mmc@...10000 {
> - compatible = "allwinner,sun7i-a20-mmc";
> - reg = <0x01c10000 0x1000>;
> - clocks = <&ccu CLK_BUS_MMC1>,
> - <&ccu CLK_MMC1>,
> - <&ccu CLK_MMC1_OUTPUT>,
> - <&ccu CLK_MMC1_SAMPLE>;
> - clock-names = "ahb",
> - "mmc",
> - "output",
> - "sample";
> - resets = <&ccu RST_BUS_MMC1>;
> - reset-names = "ahb";
> - interrupts = <GIC_SPI 61 IRQ_TYPE_LEVEL_HIGH>;
> - status = "disabled";
> - #address-cells = <1>;
> - #size-cells = <0>;
> - };
> -
> - mmc2: mmc@...11000 {
> - compatible = "allwinner,sun7i-a20-mmc";
> - reg = <0x01c11000 0x1000>;
> - clocks = <&ccu CLK_BUS_MMC2>,
> - <&ccu CLK_MMC2>,
> - <&ccu CLK_MMC2_OUTPUT>,
> - <&ccu CLK_MMC2_SAMPLE>;
> - clock-names = "ahb",
> - "mmc",
> - "output",
> - "sample";
> - resets = <&ccu RST_BUS_MMC2>;
> - reset-names = "ahb";
> - interrupts = <GIC_SPI 62 IRQ_TYPE_LEVEL_HIGH>;
> - status = "disabled";
> - #address-cells = <1>;
> - #size-cells = <0>;
> - };
> -
> - usbphy: phy@...19400 {
> - compatible = "allwinner,sun8i-h3-usb-phy";
> - reg = <0x01c19400 0x2c>,
> - <0x01c1a800 0x4>,
> - <0x01c1b800 0x4>,
> - <0x01c1c800 0x4>,
> - <0x01c1d800 0x4>;
> - reg-names = "phy_ctrl",
> - "pmu0",
> - "pmu1",
> - "pmu2",
> - "pmu3";
> - clocks = <&ccu CLK_USB_PHY0>,
> - <&ccu CLK_USB_PHY1>,
> - <&ccu CLK_USB_PHY2>,
> - <&ccu CLK_USB_PHY3>;
> - clock-names = "usb0_phy",
> - "usb1_phy",
> - "usb2_phy",
> - "usb3_phy";
> - resets = <&ccu RST_USB_PHY0>,
> - <&ccu RST_USB_PHY1>,
> - <&ccu RST_USB_PHY2>,
> - <&ccu RST_USB_PHY3>;
> - reset-names = "usb0_reset",
> - "usb1_reset",
> - "usb2_reset",
> - "usb3_reset";
> - status = "disabled";
> - #phy-cells = <1>;
> - };
> -
> - ehci1: usb@...1b000 {
> - compatible = "allwinner,sun8i-h3-ehci", "generic-ehci";
> - reg = <0x01c1b000 0x100>;
> - interrupts = <GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH>;
> - clocks = <&ccu CLK_BUS_EHCI1>, <&ccu CLK_BUS_OHCI1>;
> - resets = <&ccu RST_BUS_EHCI1>, <&ccu RST_BUS_OHCI1>;
> - phys = <&usbphy 1>;
> - phy-names = "usb";
> - status = "disabled";
> - };
> -
> - ohci1: usb@...1b400 {
> - compatible = "allwinner,sun8i-h3-ohci", "generic-ohci";
> - reg = <0x01c1b400 0x100>;
> - interrupts = <GIC_SPI 75 IRQ_TYPE_LEVEL_HIGH>;
> - clocks = <&ccu CLK_BUS_EHCI1>, <&ccu CLK_BUS_OHCI1>,
> - <&ccu CLK_USB_OHCI1>;
> - resets = <&ccu RST_BUS_EHCI1>, <&ccu RST_BUS_OHCI1>;
> - phys = <&usbphy 1>;
> - phy-names = "usb";
> - status = "disabled";
> - };
> -
> - ehci2: usb@...1c000 {
> - compatible = "allwinner,sun8i-h3-ehci", "generic-ehci";
> - reg = <0x01c1c000 0x100>;
> - interrupts = <GIC_SPI 76 IRQ_TYPE_LEVEL_HIGH>;
> - clocks = <&ccu CLK_BUS_EHCI2>, <&ccu CLK_BUS_OHCI2>;
> - resets = <&ccu RST_BUS_EHCI2>, <&ccu RST_BUS_OHCI2>;
> - phys = <&usbphy 2>;
> - phy-names = "usb";
> - status = "disabled";
> - };
> -
> - ohci2: usb@...1c400 {
> - compatible = "allwinner,sun8i-h3-ohci", "generic-ohci";
> - reg = <0x01c1c400 0x100>;
> - interrupts = <GIC_SPI 77 IRQ_TYPE_LEVEL_HIGH>;
> - clocks = <&ccu CLK_BUS_EHCI2>, <&ccu CLK_BUS_OHCI2>,
> - <&ccu CLK_USB_OHCI2>;
> - resets = <&ccu RST_BUS_EHCI2>, <&ccu RST_BUS_OHCI2>;
> - phys = <&usbphy 2>;
> - phy-names = "usb";
> - status = "disabled";
> - };
> -
> - ehci3: usb@...1d000 {
> - compatible = "allwinner,sun8i-h3-ehci", "generic-ehci";
> - reg = <0x01c1d000 0x100>;
> - interrupts = <GIC_SPI 78 IRQ_TYPE_LEVEL_HIGH>;
> - clocks = <&ccu CLK_BUS_EHCI3>, <&ccu CLK_BUS_OHCI3>;
> - resets = <&ccu RST_BUS_EHCI3>, <&ccu RST_BUS_OHCI3>;
> - phys = <&usbphy 3>;
> - phy-names = "usb";
> - status = "disabled";
> - };
> -
> - ohci3: usb@...1d400 {
> - compatible = "allwinner,sun8i-h3-ohci", "generic-ohci";
> - reg = <0x01c1d400 0x100>;
> - interrupts = <GIC_SPI 79 IRQ_TYPE_LEVEL_HIGH>;
> - clocks = <&ccu CLK_BUS_EHCI3>, <&ccu CLK_BUS_OHCI3>,
> - <&ccu CLK_USB_OHCI3>;
> - resets = <&ccu RST_BUS_EHCI3>, <&ccu RST_BUS_OHCI3>;
> - phys = <&usbphy 3>;
> - phy-names = "usb";
> - status = "disabled";
> - };
> -
> - ccu: clock@...20000 {
> - compatible = "allwinner,sun8i-h3-ccu";
> - reg = <0x01c20000 0x400>;
> - clocks = <&osc24M>, <&osc32k>;
> - clock-names = "hosc", "losc";
> - #clock-cells = <1>;
> - #reset-cells = <1>;
> - };
> -
> - pio: pinctrl@...20800 {
> - compatible = "allwinner,sun8i-h3-pinctrl";
> - reg = <0x01c20800 0x400>;
> - interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>,
> - <GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>;
> - clocks = <&ccu CLK_BUS_PIO>, <&osc24M>, <&osc32k>;
> - clock-names = "apb", "hosc", "losc";
> - gpio-controller;
> - #gpio-cells = <3>;
> - interrupt-controller;
> - #interrupt-cells = <3>;
> -
> - i2c0_pins: i2c0 {
> - pins = "PA11", "PA12";
> - function = "i2c0";
> - };
> -
> - i2c1_pins: i2c1 {
> - pins = "PA18", "PA19";
> - function = "i2c1";
> - };
> -
> - i2c2_pins: i2c2 {
> - pins = "PE12", "PE13";
> - function = "i2c2";
> - };
> -
> - mmc0_pins_a: mmc0@0 {
> - pins = "PF0", "PF1", "PF2", "PF3",
> - "PF4", "PF5";
> - function = "mmc0";
> - drive-strength = <30>;
> - bias-pull-up;
> - };
> -
> - mmc0_cd_pin: mmc0_cd_pin@0 {
> - pins = "PF6";
> - function = "gpio_in";
> - bias-pull-up;
> - };
> -
> - mmc1_pins_a: mmc1@0 {
> - pins = "PG0", "PG1", "PG2", "PG3",
> - "PG4", "PG5";
> - function = "mmc1";
> - drive-strength = <30>;
> - bias-pull-up;
> - };
> -
> - mmc2_8bit_pins: mmc2_8bit {
> - pins = "PC5", "PC6", "PC8",
> - "PC9", "PC10", "PC11",
> - "PC12", "PC13", "PC14",
> - "PC15", "PC16";
> - function = "mmc2";
> - drive-strength = <30>;
> - bias-pull-up;
> - };
> -
> - spi0_pins: spi0 {
> - pins = "PC0", "PC1", "PC2", "PC3";
> - function = "spi0";
> - };
> -
> - spi1_pins: spi1 {
> - pins = "PA15", "PA16", "PA14", "PA13";
> - function = "spi1";
> - };
> -
> - uart0_pins_a: uart0@0 {
> - pins = "PA4", "PA5";
> - function = "uart0";
> - };
> -
> - uart1_pins: uart1 {
> - pins = "PG6", "PG7";
> - function = "uart1";
> - };
> -
> - uart1_rts_cts_pins: uart1_rts_cts {
> - pins = "PG8", "PG9";
> - function = "uart1";
> - };
> -
> - uart2_pins: uart2 {
> - pins = "PA0", "PA1";
> - function = "uart2";
> - };
> -
> - uart3_pins: uart3 {
> - pins = "PA13", "PA14";
> - function = "uart3";
> - };
> - };
> -
> - timer@...20c00 {
> - compatible = "allwinner,sun4i-a10-timer";
> - reg = <0x01c20c00 0xa0>;
> - interrupts = <GIC_SPI 18 IRQ_TYPE_LEVEL_HIGH>,
> - <GIC_SPI 19 IRQ_TYPE_LEVEL_HIGH>;
> - clocks = <&osc24M>;
> - };
> -
> - spi0: spi@...68000 {
> - compatible = "allwinner,sun8i-h3-spi";
> - reg = <0x01c68000 0x1000>;
> - interrupts = <GIC_SPI 65 IRQ_TYPE_LEVEL_HIGH>;
> - clocks = <&ccu CLK_BUS_SPI0>, <&ccu CLK_SPI0>;
> - clock-names = "ahb", "mod";
> - dmas = <&dma 23>, <&dma 23>;
> - dma-names = "rx", "tx";
> - pinctrl-names = "default";
> - pinctrl-0 = <&spi0_pins>;
> - resets = <&ccu RST_BUS_SPI0>;
> - status = "disabled";
> - #address-cells = <1>;
> - #size-cells = <0>;
> - };
> -
> - spi1: spi@...69000 {
> - compatible = "allwinner,sun8i-h3-spi";
> - reg = <0x01c69000 0x1000>;
> - interrupts = <GIC_SPI 66 IRQ_TYPE_LEVEL_HIGH>;
> - clocks = <&ccu CLK_BUS_SPI1>, <&ccu CLK_SPI1>;
> - clock-names = "ahb", "mod";
> - dmas = <&dma 24>, <&dma 24>;
> - dma-names = "rx", "tx";
> - pinctrl-names = "default";
> - pinctrl-0 = <&spi1_pins>;
> - resets = <&ccu RST_BUS_SPI1>;
> - status = "disabled";
> - #address-cells = <1>;
> - #size-cells = <0>;
> - };
> -
> - wdt0: watchdog@...20ca0 {
> - compatible = "allwinner,sun6i-a31-wdt";
> - reg = <0x01c20ca0 0x20>;
> - interrupts = <GIC_SPI 25 IRQ_TYPE_LEVEL_HIGH>;
> - };
> -
> - pwm: pwm@...21400 {
> - compatible = "allwinner,sun8i-h3-pwm";
> - reg = <0x01c21400 0x8>;
> - clocks = <&osc24M>;
> - #pwm-cells = <3>;
> - status = "disabled";
> - };
> -
> - codec: codec@...22c00 {
> - #sound-dai-cells = <0>;
> - compatible = "allwinner,sun8i-h3-codec";
> - reg = <0x01c22c00 0x400>;
> - interrupts = <GIC_SPI 29 IRQ_TYPE_LEVEL_HIGH>;
> - clocks = <&ccu CLK_BUS_CODEC>, <&ccu CLK_AC_DIG>;
> - clock-names = "apb", "codec";
> - resets = <&ccu RST_BUS_CODEC>;
> - dmas = <&dma 15>, <&dma 15>;
> - dma-names = "rx", "tx";
> - allwinner,codec-analog-controls = <&codec_analog>;
> - status = "disabled";
> - };
> -
> - uart0: serial@...28000 {
> - compatible = "snps,dw-apb-uart";
> - reg = <0x01c28000 0x400>;
> - interrupts = <GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>;
> - reg-shift = <2>;
> - reg-io-width = <4>;
> - clocks = <&ccu CLK_BUS_UART0>;
> - resets = <&ccu RST_BUS_UART0>;
> - dmas = <&dma 6>, <&dma 6>;
> - dma-names = "rx", "tx";
> - status = "disabled";
> - };
> -
> - uart1: serial@...28400 {
> - compatible = "snps,dw-apb-uart";
> - reg = <0x01c28400 0x400>;
> - interrupts = <GIC_SPI 1 IRQ_TYPE_LEVEL_HIGH>;
> - reg-shift = <2>;
> - reg-io-width = <4>;
> - clocks = <&ccu CLK_BUS_UART1>;
> - resets = <&ccu RST_BUS_UART1>;
> - dmas = <&dma 7>, <&dma 7>;
> - dma-names = "rx", "tx";
> - status = "disabled";
> - };
> -
> - uart2: serial@...28800 {
> - compatible = "snps,dw-apb-uart";
> - reg = <0x01c28800 0x400>;
> - interrupts = <GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>;
> - reg-shift = <2>;
> - reg-io-width = <4>;
> - clocks = <&ccu CLK_BUS_UART2>;
> - resets = <&ccu RST_BUS_UART2>;
> - dmas = <&dma 8>, <&dma 8>;
> - dma-names = "rx", "tx";
> - status = "disabled";
> - };
> -
> - uart3: serial@...28c00 {
> - compatible = "snps,dw-apb-uart";
> - reg = <0x01c28c00 0x400>;
> - interrupts = <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>;
> - reg-shift = <2>;
> - reg-io-width = <4>;
> - clocks = <&ccu CLK_BUS_UART3>;
> - resets = <&ccu RST_BUS_UART3>;
> - dmas = <&dma 9>, <&dma 9>;
> - dma-names = "rx", "tx";
> - status = "disabled";
> - };
> -
> - i2c0: i2c@...2ac00 {
> - compatible = "allwinner,sun6i-a31-i2c";
> - reg = <0x01c2ac00 0x400>;
> - interrupts = <GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>;
> - clocks = <&ccu CLK_BUS_I2C0>;
> - resets = <&ccu RST_BUS_I2C0>;
> - pinctrl-names = "default";
> - pinctrl-0 = <&i2c0_pins>;
> - status = "disabled";
> - #address-cells = <1>;
> - #size-cells = <0>;
> - };
> -
> - i2c1: i2c@...2b000 {
> - compatible = "allwinner,sun6i-a31-i2c";
> - reg = <0x01c2b000 0x400>;
> - interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>;
> - clocks = <&ccu CLK_BUS_I2C1>;
> - resets = <&ccu RST_BUS_I2C1>;
> - pinctrl-names = "default";
> - pinctrl-0 = <&i2c1_pins>;
> - status = "disabled";
> - #address-cells = <1>;
> - #size-cells = <0>;
> - };
> -
> - i2c2: i2c@...2b400 {
> - compatible = "allwinner,sun6i-a31-i2c";
> - reg = <0x01c2b000 0x400>;
> - interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>;
> - clocks = <&ccu CLK_BUS_I2C2>;
> - resets = <&ccu RST_BUS_I2C2>;
> - pinctrl-names = "default";
> - pinctrl-0 = <&i2c2_pins>;
> - status = "disabled";
> - #address-cells = <1>;
> - #size-cells = <0>;
> - };
> -
> gic: interrupt-controller@...81000 {
> compatible = "arm,cortex-a7-gic", "arm,cortex-a15-gic";
> reg = <0x01c81000 0x1000>,
> @@ -580,51 +93,49 @@
> #interrupt-cells = <3>;
> interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>;
> };
> + };
> +};
>
> - rtc: rtc@...00000 {
> - compatible = "allwinner,sun6i-a31-rtc";
> - reg = <0x01f00000 0x54>;
> - interrupts = <GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH>,
> - <GIC_SPI 41 IRQ_TYPE_LEVEL_HIGH>;
> - };
> -
> - apb0_reset: reset@...014b0 {
> - reg = <0x01f014b0 0x4>;
> - compatible = "allwinner,sun6i-a31-clock-reset";
> - #reset-cells = <1>;
> - };
> +&ccu {
> + compatible = "allwinner,sun8i-h3-ccu";
> +};
I believe this kind of sharing nodes is a bit frowned upon in connection
with sharing .dtsi's. If the compatible name differs, I think it
deserves to be a separate node spelt out in each SoC's .dtsi.
This also makes the DT more readable, since a reader doesn't have to
refer to two files to see what's in that node.
>
> - codec_analog: codec-analog@...015c0 {
> - compatible = "allwinner,sun8i-h3-codec-analog";
> - reg = <0x01f015c0 0x4>;
> - };
> +&mmc0 {
> + compatible = "allwinner,sun7i-a20-mmc";
> + clocks = <&ccu CLK_BUS_MMC0>,
> + <&ccu CLK_MMC0>,
> + <&ccu CLK_MMC0_OUTPUT>,
> + <&ccu CLK_MMC0_SAMPLE>;
> + clock-names = "ahb",
> + "mmc",
> + "output",
> + "sample";
This applies even more here, since the MMC controllers also have
different clock requirements.
So why can't we just leave the CCU, MMC and possibly the pinctrl nodes
completely out of the shared h3-h5.dtsi and introduce them from scratch
in the SoC specific .dtsi?
I think we still have enough identical nodes to justify this kind of
.dtsi sharing.
Cheers,
Andre.
> +};
>
> - ir: ir@...02000 {
> - compatible = "allwinner,sun5i-a13-ir";
> - clocks = <&apb0_gates 1>, <&ir_clk>;
> - clock-names = "apb", "ir";
> - resets = <&apb0_reset 1>;
> - interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>;
> - reg = <0x01f02000 0x40>;
> - status = "disabled";
> - };
> +&mmc1 {
> + compatible = "allwinner,sun7i-a20-mmc";
> + clocks = <&ccu CLK_BUS_MMC1>,
> + <&ccu CLK_MMC1>,
> + <&ccu CLK_MMC1_OUTPUT>,
> + <&ccu CLK_MMC1_SAMPLE>;
> + clock-names = "ahb",
> + "mmc",
> + "output",
> + "sample";
> +};
>
> - r_pio: pinctrl@...02c00 {
> - compatible = "allwinner,sun8i-h3-r-pinctrl";
> - reg = <0x01f02c00 0x400>;
> - interrupts = <GIC_SPI 45 IRQ_TYPE_LEVEL_HIGH>;
> - clocks = <&apb0_gates 0>, <&osc24M>, <&osc32k>;
> - clock-names = "apb", "hosc", "losc";
> - resets = <&apb0_reset 0>;
> - gpio-controller;
> - #gpio-cells = <3>;
> - interrupt-controller;
> - #interrupt-cells = <3>;
> +&mmc2 {
> + compatible = "allwinner,sun7i-a20-mmc";
> + clocks = <&ccu CLK_BUS_MMC2>,
> + <&ccu CLK_MMC2>,
> + <&ccu CLK_MMC2_OUTPUT>,
> + <&ccu CLK_MMC2_SAMPLE>;
> + clock-names = "ahb",
> + "mmc",
> + "output",
> + "sample";
> +};
>
> - ir_pins_a: ir@0 {
> - pins = "PL11";
> - function = "s_cir_rx";
> - };
> - };
> - };
> +&pio {
> + compatible = "allwinner,sun8i-h3-pinctrl";
> };
> diff --git a/arch/arm/boot/dts/sunxi-h3-h5.dtsi b/arch/arm/boot/dts/sunxi-h3-h5.dtsi
> new file mode 100644
> index 000000000000..4a57c65e8869
> --- /dev/null
> +++ b/arch/arm/boot/dts/sunxi-h3-h5.dtsi
> @@ -0,0 +1,557 @@
> +/*
> + * Copyright (C) 2015 Jens Kuske <jenskuske@...il.com>
> + *
> + * This file is dual-licensed: you can use it either under the terms
> + * of the GPL or the X11 license, at your option. Note that this dual
> + * licensing only applies to this file, and not this project as a
> + * whole.
> + *
> + * a) This file is free software; you can redistribute it and/or
> + * modify it under the terms of the GNU General Public License as
> + * published by the Free Software Foundation; either version 2 of the
> + * License, or (at your option) any later version.
> + *
> + * This file is distributed in the hope that it will be useful,
> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> + * GNU General Public License for more details.
> + *
> + * Or, alternatively,
> + *
> + * b) Permission is hereby granted, free of charge, to any person
> + * obtaining a copy of this software and associated documentation
> + * files (the "Software"), to deal in the Software without
> + * restriction, including without limitation the rights to use,
> + * copy, modify, merge, publish, distribute, sublicense, and/or
> + * sell copies of the Software, and to permit persons to whom the
> + * Software is furnished to do so, subject to the following
> + * conditions:
> + *
> + * The above copyright notice and this permission notice shall be
> + * included in all copies or substantial portions of the Software.
> + *
> + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
> + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
> + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
> + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
> + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
> + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
> + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
> + * OTHER DEALINGS IN THE SOFTWARE.
> + */
> +
> +#include <dt-bindings/clock/sunxi-h3-h5-ccu.h>
> +#include <dt-bindings/interrupt-controller/arm-gic.h>
> +#include <dt-bindings/pinctrl/sun4i-a10.h>
> +#include <dt-bindings/reset/sunxi-h3-h5-ccu.h>
> +
> +/ {
> + #address-cells = <1>;
> + #size-cells = <1>;
> +
> + clocks {
> + #address-cells = <1>;
> + #size-cells = <1>;
> + ranges;
> +
> + osc24M: osc24M_clk {
> + #clock-cells = <0>;
> + compatible = "fixed-clock";
> + clock-frequency = <24000000>;
> + clock-output-names = "osc24M";
> + };
> +
> + osc32k: osc32k_clk {
> + #clock-cells = <0>;
> + compatible = "fixed-clock";
> + clock-frequency = <32768>;
> + clock-output-names = "osc32k";
> + };
> +
> + apb0: apb0_clk {
> + compatible = "fixed-factor-clock";
> + #clock-cells = <0>;
> + clock-div = <1>;
> + clock-mult = <1>;
> + clocks = <&osc24M>;
> + clock-output-names = "apb0";
> + };
> +
> + apb0_gates: clk@...01428 {
> + compatible = "allwinner,sun8i-h3-apb0-gates-clk",
> + "allwinner,sun4i-a10-gates-clk";
> + reg = <0x01f01428 0x4>;
> + #clock-cells = <1>;
> + clocks = <&apb0>;
> + clock-indices = <0>, <1>;
> + clock-output-names = "apb0_pio", "apb0_ir";
> + };
> +
> + ir_clk: ir_clk@...01454 {
> + compatible = "allwinner,sun4i-a10-mod0-clk";
> + reg = <0x01f01454 0x4>;
> + #clock-cells = <0>;
> + clocks = <&osc32k>, <&osc24M>;
> + clock-output-names = "ir";
> + };
> + };
> +
> + soc {
> + compatible = "simple-bus";
> + #address-cells = <1>;
> + #size-cells = <1>;
> + ranges;
> +
> + dma: dma-controller@...02000 {
> + compatible = "allwinner,sun8i-h3-dma";
> + reg = <0x01c02000 0x1000>;
> + interrupts = <GIC_SPI 50 IRQ_TYPE_LEVEL_HIGH>;
> + clocks = <&ccu CLK_BUS_DMA>;
> + resets = <&ccu RST_BUS_DMA>;
> + #dma-cells = <1>;
> + };
> +
> + mmc0: mmc@...0f000 {
> + /* compatible and clocks are in per SoC .dtsi file */
> + reg = <0x01c0f000 0x1000>;
> + resets = <&ccu RST_BUS_MMC0>;
> + reset-names = "ahb";
> + interrupts = <GIC_SPI 60 IRQ_TYPE_LEVEL_HIGH>;
> + status = "disabled";
> + #address-cells = <1>;
> + #size-cells = <0>;
> + };
> +
> + mmc1: mmc@...10000 {
> + /* compatible and clocks are in per SoC .dtsi file */
> + reg = <0x01c10000 0x1000>;
> + resets = <&ccu RST_BUS_MMC1>;
> + reset-names = "ahb";
> + interrupts = <GIC_SPI 61 IRQ_TYPE_LEVEL_HIGH>;
> + status = "disabled";
> + #address-cells = <1>;
> + #size-cells = <0>;
> + };
> +
> + mmc2: mmc@...11000 {
> + /* compatible and clocks are in per SoC .dtsi file */
> + reg = <0x01c11000 0x1000>;
> + resets = <&ccu RST_BUS_MMC2>;
> + reset-names = "ahb";
> + interrupts = <GIC_SPI 62 IRQ_TYPE_LEVEL_HIGH>;
> + status = "disabled";
> + #address-cells = <1>;
> + #size-cells = <0>;
> + };
> +
> + usbphy: phy@...19400 {
> + compatible = "allwinner,sun8i-h3-usb-phy";
> + reg = <0x01c19400 0x2c>,
> + <0x01c1a800 0x4>,
> + <0x01c1b800 0x4>,
> + <0x01c1c800 0x4>,
> + <0x01c1d800 0x4>;
> + reg-names = "phy_ctrl",
> + "pmu0",
> + "pmu1",
> + "pmu2",
> + "pmu3";
> + clocks = <&ccu CLK_USB_PHY0>,
> + <&ccu CLK_USB_PHY1>,
> + <&ccu CLK_USB_PHY2>,
> + <&ccu CLK_USB_PHY3>;
> + clock-names = "usb0_phy",
> + "usb1_phy",
> + "usb2_phy",
> + "usb3_phy";
> + resets = <&ccu RST_USB_PHY0>,
> + <&ccu RST_USB_PHY1>,
> + <&ccu RST_USB_PHY2>,
> + <&ccu RST_USB_PHY3>;
> + reset-names = "usb0_reset",
> + "usb1_reset",
> + "usb2_reset",
> + "usb3_reset";
> + status = "disabled";
> + #phy-cells = <1>;
> + };
> +
> + ehci1: usb@...1b000 {
> + compatible = "allwinner,sun8i-h3-ehci", "generic-ehci";
> + reg = <0x01c1b000 0x100>;
> + interrupts = <GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH>;
> + clocks = <&ccu CLK_BUS_EHCI1>, <&ccu CLK_BUS_OHCI1>;
> + resets = <&ccu RST_BUS_EHCI1>, <&ccu RST_BUS_OHCI1>;
> + phys = <&usbphy 1>;
> + phy-names = "usb";
> + status = "disabled";
> + };
> +
> + ohci1: usb@...1b400 {
> + compatible = "allwinner,sun8i-h3-ohci", "generic-ohci";
> + reg = <0x01c1b400 0x100>;
> + interrupts = <GIC_SPI 75 IRQ_TYPE_LEVEL_HIGH>;
> + clocks = <&ccu CLK_BUS_EHCI1>, <&ccu CLK_BUS_OHCI1>,
> + <&ccu CLK_USB_OHCI1>;
> + resets = <&ccu RST_BUS_EHCI1>, <&ccu RST_BUS_OHCI1>;
> + phys = <&usbphy 1>;
> + phy-names = "usb";
> + status = "disabled";
> + };
> +
> + ehci2: usb@...1c000 {
> + compatible = "allwinner,sun8i-h3-ehci", "generic-ehci";
> + reg = <0x01c1c000 0x100>;
> + interrupts = <GIC_SPI 76 IRQ_TYPE_LEVEL_HIGH>;
> + clocks = <&ccu CLK_BUS_EHCI2>, <&ccu CLK_BUS_OHCI2>;
> + resets = <&ccu RST_BUS_EHCI2>, <&ccu RST_BUS_OHCI2>;
> + phys = <&usbphy 2>;
> + phy-names = "usb";
> + status = "disabled";
> + };
> +
> + ohci2: usb@...1c400 {
> + compatible = "allwinner,sun8i-h3-ohci", "generic-ohci";
> + reg = <0x01c1c400 0x100>;
> + interrupts = <GIC_SPI 77 IRQ_TYPE_LEVEL_HIGH>;
> + clocks = <&ccu CLK_BUS_EHCI2>, <&ccu CLK_BUS_OHCI2>,
> + <&ccu CLK_USB_OHCI2>;
> + resets = <&ccu RST_BUS_EHCI2>, <&ccu RST_BUS_OHCI2>;
> + phys = <&usbphy 2>;
> + phy-names = "usb";
> + status = "disabled";
> + };
> +
> + ehci3: usb@...1d000 {
> + compatible = "allwinner,sun8i-h3-ehci", "generic-ehci";
> + reg = <0x01c1d000 0x100>;
> + interrupts = <GIC_SPI 78 IRQ_TYPE_LEVEL_HIGH>;
> + clocks = <&ccu CLK_BUS_EHCI3>, <&ccu CLK_BUS_OHCI3>;
> + resets = <&ccu RST_BUS_EHCI3>, <&ccu RST_BUS_OHCI3>;
> + phys = <&usbphy 3>;
> + phy-names = "usb";
> + status = "disabled";
> + };
> +
> + ohci3: usb@...1d400 {
> + compatible = "allwinner,sun8i-h3-ohci", "generic-ohci";
> + reg = <0x01c1d400 0x100>;
> + interrupts = <GIC_SPI 79 IRQ_TYPE_LEVEL_HIGH>;
> + clocks = <&ccu CLK_BUS_EHCI3>, <&ccu CLK_BUS_OHCI3>,
> + <&ccu CLK_USB_OHCI3>;
> + resets = <&ccu RST_BUS_EHCI3>, <&ccu RST_BUS_OHCI3>;
> + phys = <&usbphy 3>;
> + phy-names = "usb";
> + status = "disabled";
> + };
> +
> + ccu: clock@...20000 {
> + /* compatible is in per SoC .dtsi file */
> + reg = <0x01c20000 0x400>;
> + clocks = <&osc24M>, <&osc32k>;
> + clock-names = "hosc", "losc";
> + #clock-cells = <1>;
> + #reset-cells = <1>;
> + };
> +
> + pio: pinctrl@...20800 {
> + /* compatible is in per SoC .dtsi file */
> + reg = <0x01c20800 0x400>;
> + interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>;
> + clocks = <&ccu CLK_BUS_PIO>, <&osc24M>, <&osc32k>;
> + clock-names = "apb", "hosc", "losc";
> + gpio-controller;
> + #gpio-cells = <3>;
> + interrupt-controller;
> + #interrupt-cells = <3>;
> +
> + i2c0_pins: i2c0 {
> + pins = "PA11", "PA12";
> + function = "i2c0";
> + };
> +
> + i2c1_pins: i2c1 {
> + pins = "PA18", "PA19";
> + function = "i2c1";
> + };
> +
> + i2c2_pins: i2c2 {
> + pins = "PE12", "PE13";
> + function = "i2c2";
> + };
> +
> + mmc0_pins_a: mmc0@0 {
> + pins = "PF0", "PF1", "PF2", "PF3",
> + "PF4", "PF5";
> + function = "mmc0";
> + drive-strength = <30>;
> + bias-pull-up;
> + };
> +
> + mmc0_cd_pin: mmc0_cd_pin@0 {
> + pins = "PF6";
> + function = "gpio_in";
> + bias-pull-up;
> + };
> +
> + mmc1_pins_a: mmc1@0 {
> + pins = "PG0", "PG1", "PG2", "PG3",
> + "PG4", "PG5";
> + function = "mmc1";
> + drive-strength = <30>;
> + bias-pull-up;
> + };
> +
> + mmc2_8bit_pins: mmc2_8bit {
> + pins = "PC5", "PC6", "PC8",
> + "PC9", "PC10", "PC11",
> + "PC12", "PC13", "PC14",
> + "PC15", "PC16";
> + function = "mmc2";
> + drive-strength = <30>;
> + bias-pull-up;
> + };
> +
> + spi0_pins: spi0 {
> + pins = "PC0", "PC1", "PC2", "PC3";
> + function = "spi0";
> + };
> +
> + spi1_pins: spi1 {
> + pins = "PA15", "PA16", "PA14", "PA13";
> + function = "spi1";
> + };
> +
> + uart0_pins_a: uart0@0 {
> + pins = "PA4", "PA5";
> + function = "uart0";
> + };
> +
> + uart1_pins: uart1 {
> + pins = "PG6", "PG7";
> + function = "uart1";
> + };
> +
> + uart1_rts_cts_pins: uart1_rts_cts {
> + pins = "PG8", "PG9";
> + function = "uart1";
> + };
> +
> + uart2_pins: uart2 {
> + pins = "PA0", "PA1";
> + function = "uart2";
> + };
> +
> + uart3_pins: uart3 {
> + pins = "PA13", "PA14";
> + function = "uart3";
> + };
> + };
> +
> + timer@...20c00 {
> + compatible = "allwinner,sun4i-a10-timer";
> + reg = <0x01c20c00 0xa0>;
> + interrupts = <GIC_SPI 18 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 19 IRQ_TYPE_LEVEL_HIGH>;
> + clocks = <&osc24M>;
> + };
> +
> + spi0: spi@...68000 {
> + compatible = "allwinner,sun8i-h3-spi";
> + reg = <0x01c68000 0x1000>;
> + interrupts = <GIC_SPI 65 IRQ_TYPE_LEVEL_HIGH>;
> + clocks = <&ccu CLK_BUS_SPI0>, <&ccu CLK_SPI0>;
> + clock-names = "ahb", "mod";
> + dmas = <&dma 23>, <&dma 23>;
> + dma-names = "rx", "tx";
> + pinctrl-names = "default";
> + pinctrl-0 = <&spi0_pins>;
> + resets = <&ccu RST_BUS_SPI0>;
> + status = "disabled";
> + #address-cells = <1>;
> + #size-cells = <0>;
> + };
> +
> + spi1: spi@...69000 {
> + compatible = "allwinner,sun8i-h3-spi";
> + reg = <0x01c69000 0x1000>;
> + interrupts = <GIC_SPI 66 IRQ_TYPE_LEVEL_HIGH>;
> + clocks = <&ccu CLK_BUS_SPI1>, <&ccu CLK_SPI1>;
> + clock-names = "ahb", "mod";
> + dmas = <&dma 24>, <&dma 24>;
> + dma-names = "rx", "tx";
> + pinctrl-names = "default";
> + pinctrl-0 = <&spi1_pins>;
> + resets = <&ccu RST_BUS_SPI1>;
> + status = "disabled";
> + #address-cells = <1>;
> + #size-cells = <0>;
> + };
> +
> + wdt0: watchdog@...20ca0 {
> + compatible = "allwinner,sun6i-a31-wdt";
> + reg = <0x01c20ca0 0x20>;
> + interrupts = <GIC_SPI 25 IRQ_TYPE_LEVEL_HIGH>;
> + };
> +
> + pwm: pwm@...21400 {
> + compatible = "allwinner,sun8i-h3-pwm";
> + reg = <0x01c21400 0x8>;
> + clocks = <&osc24M>;
> + #pwm-cells = <3>;
> + status = "disabled";
> + };
> +
> + codec: codec@...22c00 {
> + #sound-dai-cells = <0>;
> + compatible = "allwinner,sun8i-h3-codec";
> + reg = <0x01c22c00 0x400>;
> + interrupts = <GIC_SPI 29 IRQ_TYPE_LEVEL_HIGH>;
> + clocks = <&ccu CLK_BUS_CODEC>, <&ccu CLK_AC_DIG>;
> + clock-names = "apb", "codec";
> + resets = <&ccu RST_BUS_CODEC>;
> + dmas = <&dma 15>, <&dma 15>;
> + dma-names = "rx", "tx";
> + allwinner,codec-analog-controls = <&codec_analog>;
> + status = "disabled";
> + };
> +
> + uart0: serial@...28000 {
> + compatible = "snps,dw-apb-uart";
> + reg = <0x01c28000 0x400>;
> + interrupts = <GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>;
> + reg-shift = <2>;
> + reg-io-width = <4>;
> + clocks = <&ccu CLK_BUS_UART0>;
> + resets = <&ccu RST_BUS_UART0>;
> + dmas = <&dma 6>, <&dma 6>;
> + dma-names = "rx", "tx";
> + status = "disabled";
> + };
> +
> + uart1: serial@...28400 {
> + compatible = "snps,dw-apb-uart";
> + reg = <0x01c28400 0x400>;
> + interrupts = <GIC_SPI 1 IRQ_TYPE_LEVEL_HIGH>;
> + reg-shift = <2>;
> + reg-io-width = <4>;
> + clocks = <&ccu CLK_BUS_UART1>;
> + resets = <&ccu RST_BUS_UART1>;
> + dmas = <&dma 7>, <&dma 7>;
> + dma-names = "rx", "tx";
> + status = "disabled";
> + };
> +
> + uart2: serial@...28800 {
> + compatible = "snps,dw-apb-uart";
> + reg = <0x01c28800 0x400>;
> + interrupts = <GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>;
> + reg-shift = <2>;
> + reg-io-width = <4>;
> + clocks = <&ccu CLK_BUS_UART2>;
> + resets = <&ccu RST_BUS_UART2>;
> + dmas = <&dma 8>, <&dma 8>;
> + dma-names = "rx", "tx";
> + status = "disabled";
> + };
> +
> + uart3: serial@...28c00 {
> + compatible = "snps,dw-apb-uart";
> + reg = <0x01c28c00 0x400>;
> + interrupts = <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>;
> + reg-shift = <2>;
> + reg-io-width = <4>;
> + clocks = <&ccu CLK_BUS_UART3>;
> + resets = <&ccu RST_BUS_UART3>;
> + dmas = <&dma 9>, <&dma 9>;
> + dma-names = "rx", "tx";
> + status = "disabled";
> + };
> +
> + i2c0: i2c@...2ac00 {
> + compatible = "allwinner,sun6i-a31-i2c";
> + reg = <0x01c2ac00 0x400>;
> + interrupts = <GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>;
> + clocks = <&ccu CLK_BUS_I2C0>;
> + resets = <&ccu RST_BUS_I2C0>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&i2c0_pins>;
> + status = "disabled";
> + #address-cells = <1>;
> + #size-cells = <0>;
> + };
> +
> + i2c1: i2c@...2b000 {
> + compatible = "allwinner,sun6i-a31-i2c";
> + reg = <0x01c2b000 0x400>;
> + interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>;
> + clocks = <&ccu CLK_BUS_I2C1>;
> + resets = <&ccu RST_BUS_I2C1>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&i2c1_pins>;
> + status = "disabled";
> + #address-cells = <1>;
> + #size-cells = <0>;
> + };
> +
> + i2c2: i2c@...2b400 {
> + compatible = "allwinner,sun6i-a31-i2c";
> + reg = <0x01c2b000 0x400>;
> + interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>;
> + clocks = <&ccu CLK_BUS_I2C2>;
> + resets = <&ccu RST_BUS_I2C2>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&i2c2_pins>;
> + status = "disabled";
> + #address-cells = <1>;
> + #size-cells = <0>;
> + };
> +
> + rtc: rtc@...00000 {
> + compatible = "allwinner,sun6i-a31-rtc";
> + reg = <0x01f00000 0x54>;
> + interrupts = <GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 41 IRQ_TYPE_LEVEL_HIGH>;
> + };
> +
> + apb0_reset: reset@...014b0 {
> + reg = <0x01f014b0 0x4>;
> + compatible = "allwinner,sun6i-a31-clock-reset";
> + #reset-cells = <1>;
> + };
> +
> + codec_analog: codec-analog@...015c0 {
> + compatible = "allwinner,sun8i-h3-codec-analog";
> + reg = <0x01f015c0 0x4>;
> + };
> +
> + ir: ir@...02000 {
> + compatible = "allwinner,sun5i-a13-ir";
> + clocks = <&apb0_gates 1>, <&ir_clk>;
> + clock-names = "apb", "ir";
> + resets = <&apb0_reset 1>;
> + interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>;
> + reg = <0x01f02000 0x40>;
> + status = "disabled";
> + };
> +
> + r_pio: pinctrl@...02c00 {
> + compatible = "allwinner,sun8i-h3-r-pinctrl";
> + reg = <0x01f02c00 0x400>;
> + interrupts = <GIC_SPI 45 IRQ_TYPE_LEVEL_HIGH>;
> + clocks = <&apb0_gates 0>, <&osc24M>, <&osc32k>;
> + clock-names = "apb", "hosc", "losc";
> + resets = <&apb0_reset 0>;
> + gpio-controller;
> + #gpio-cells = <3>;
> + interrupt-controller;
> + #interrupt-cells = <3>;
> +
> + ir_pins_a: ir@0 {
> + pins = "PL11";
> + function = "s_cir_rx";
> + };
> + };
> + };
> +};
>
Powered by blists - more mailing lists