| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-id: <8266689.kdSZWCWITZ@amdc3058>
Date: Mon, 13 Feb 2017 17:22:48 +0100
From: Bartlomiej Zolnierkiewicz <b.zolnierkie@...sung.com>
To: Krzysztof Kozlowski <krzk@...nel.org>
Cc: Zhang Rui <rui.zhang@...el.com>,
Eduardo Valentin <edubezval@...il.com>,
Kukjin Kim <kgene@...nel.org>,
Javier Martinez Canillas <javier@....samsung.com>,
linux-pm@...r.kernel.org, linux-samsung-soc@...r.kernel.org,
linux-arm-kernel@...ts.infradead.org, linux-kernel@...r.kernel.org,
devicetree@...r.kernel.org, Willy WOLFF <willy.mh.wolff@...il.com>,
Anand Moon <linux.amoon@...il.com>
Subject: Re: [PATCH] ARM: dts: exynos: Use thermal fuse value for thermal zone
0 on Exynos5420
On Saturday, February 11, 2017 10:14:56 PM Krzysztof Kozlowski wrote:
> In Odroid XU3 Lite board, the temperature levels reported for thermal
> zone 0 were weird. In warm room:
> /sys/class/thermal/thermal_zone0/temp:32000
> /sys/class/thermal/thermal_zone1/temp:51000
> /sys/class/thermal/thermal_zone2/temp:55000
> /sys/class/thermal/thermal_zone3/temp:54000
> /sys/class/thermal/thermal_zone4/temp:51000
>
> Sometimes after booting the value was even equal to ambient temperature
> which is highly unlikely to be a real temperature of sensor in SoC.
>
> The thermal sensor's calibration (trimming) is based on fused values.
> In case of the board above, the fused values are: 35, 52, 43, 58 and 43
> (corresponding to each TMU device). However driver defined a minimum value
> for fused data as 40 and for smaller values it was using a hard-coded 55
> instead. This lead to mapping data from sensor to wrong temperatures
> for thermal zone 0.
>
> Various vendor 3.10 trees (Hardkernel's based on Samsung LSI, Artik 10)
> do not impose any limits on fused values. Since we do not have any
> knowledge about these limits, use 0 as a minimum accepted fused value.
> This should essentially allow accepting any reasonable fused value thus
> behaving like vendor driver.
>
> The exynos5420-tmu-sensor-conf.dtsi is copied directly from existing
> exynso4412 with one change - the samsung,tmu_min_efuse_value.
>
> Signed-off-by: Krzysztof Kozlowski <krzk@...nel.org>
Acked-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@...sung.com>
Best regards,
--
Bartlomiej Zolnierkiewicz
Samsung R&D Institute Poland
Samsung Electronics
> ---
>
> Testing on other Exynos542x boards is much appreciated. Especially I
> wonder what efuse values are there.
> ---
> arch/arm/boot/dts/exynos5420-tmu-sensor-conf.dtsi | 25 +++++++++++++++++++++++
> arch/arm/boot/dts/exynos5420.dtsi | 10 ++++-----
> 2 files changed, 30 insertions(+), 5 deletions(-)
> create mode 100644 arch/arm/boot/dts/exynos5420-tmu-sensor-conf.dtsi
>
> diff --git a/arch/arm/boot/dts/exynos5420-tmu-sensor-conf.dtsi b/arch/arm/boot/dts/exynos5420-tmu-sensor-conf.dtsi
> new file mode 100644
> index 000000000000..c8771c660550
> --- /dev/null
> +++ b/arch/arm/boot/dts/exynos5420-tmu-sensor-conf.dtsi
> @@ -0,0 +1,25 @@
> +/*
> + * Device tree sources for Exynos5420 TMU sensor configuration
> + *
> + * Copyright (c) 2014 Lukasz Majewski <l.majewski@...sung.com>
> + * Copyright (c) 2017 Krzysztof Kozlowski <krzk@...nel.org>
> + *
> + * This program is free software; you can redistribute it and/or modify
> + * it under the terms of the GNU General Public License version 2 as
> + * published by the Free Software Foundation.
> + *
> + */
> +
> +#include <dt-bindings/thermal/thermal_exynos.h>
> +
> +#thermal-sensor-cells = <0>;
> +samsung,tmu_gain = <8>;
> +samsung,tmu_reference_voltage = <16>;
> +samsung,tmu_noise_cancel_mode = <4>;
> +samsung,tmu_efuse_value = <55>;
> +samsung,tmu_min_efuse_value = <0>;
> +samsung,tmu_max_efuse_value = <100>;
> +samsung,tmu_first_point_trim = <25>;
> +samsung,tmu_second_point_trim = <85>;
> +samsung,tmu_default_temp_offset = <50>;
> +samsung,tmu_cal_type = <TYPE_ONE_POINT_TRIMMING>;
> diff --git a/arch/arm/boot/dts/exynos5420.dtsi b/arch/arm/boot/dts/exynos5420.dtsi
> index 7dc9dc82afd8..83b3899d228d 100644
> --- a/arch/arm/boot/dts/exynos5420.dtsi
> +++ b/arch/arm/boot/dts/exynos5420.dtsi
> @@ -699,7 +699,7 @@
> interrupts = <0 65 IRQ_TYPE_LEVEL_HIGH>;
> clocks = <&clock CLK_TMU>;
> clock-names = "tmu_apbif";
> - #include "exynos4412-tmu-sensor-conf.dtsi"
> + #include "exynos5420-tmu-sensor-conf.dtsi"
> };
>
> tmu_cpu1: tmu@...64000 {
> @@ -708,7 +708,7 @@
> interrupts = <0 183 IRQ_TYPE_LEVEL_HIGH>;
> clocks = <&clock CLK_TMU>;
> clock-names = "tmu_apbif";
> - #include "exynos4412-tmu-sensor-conf.dtsi"
> + #include "exynos5420-tmu-sensor-conf.dtsi"
> };
>
> tmu_cpu2: tmu@...68000 {
> @@ -717,7 +717,7 @@
> interrupts = <0 184 IRQ_TYPE_LEVEL_HIGH>;
> clocks = <&clock CLK_TMU>, <&clock CLK_TMU>;
> clock-names = "tmu_apbif", "tmu_triminfo_apbif";
> - #include "exynos4412-tmu-sensor-conf.dtsi"
> + #include "exynos5420-tmu-sensor-conf.dtsi"
> };
>
> tmu_cpu3: tmu@...6c000 {
> @@ -726,7 +726,7 @@
> interrupts = <0 185 IRQ_TYPE_LEVEL_HIGH>;
> clocks = <&clock CLK_TMU>, <&clock CLK_TMU_GPU>;
> clock-names = "tmu_apbif", "tmu_triminfo_apbif";
> - #include "exynos4412-tmu-sensor-conf.dtsi"
> + #include "exynos5420-tmu-sensor-conf.dtsi"
> };
>
> tmu_gpu: tmu@...a0000 {
> @@ -735,7 +735,7 @@
> interrupts = <0 215 IRQ_TYPE_LEVEL_HIGH>;
> clocks = <&clock CLK_TMU_GPU>, <&clock CLK_TMU>;
> clock-names = "tmu_apbif", "tmu_triminfo_apbif";
> - #include "exynos4412-tmu-sensor-conf.dtsi"
> + #include "exynos5420-tmu-sensor-conf.dtsi"
> };
>
> sysmmu_g2dr: sysmmu@...0A60000 {
Powered by blists - more mailing lists