Message-ID: <64f04459-c88e-c479-04fb-267e3f3960c6@codeaurora.org>
Date:   Wed, 15 Feb 2017 10:54:31 +0530
From:   Vivek Gautam <vivek.gautam@...eaurora.org>
To:     Jaehoon Chung <jh80.chung@...sung.com>, linux-pci@...r.kernel.org
Cc:     bhelgaas@...gle.com, krzk@...nel.org, linux-kernel@...r.kernel.org,
        jingoohan1@...il.com, javier@....samsung.com, kgene@...nel.org,
        linux-samsung-soc@...r.kernel.org, cpgs@...sung.com,
        niyas.ahmed@...sung.com, alim.akhtar@...sung.com,
        pankaj.dubey@...sung.com, kishon@...com,
        devicetree@...r.kernel.org, mark.rutland@....com,
        robh+dt@...nel.org
Subject: Re: [PATCH V3 2/4] phy: phy-exynos-pcie: Add support for Exynos PCIe
 phy


On 02/13/2017 01:56 PM, Jaehoon Chung wrote:
> This patch adds support for Generic PHY framework about Exynos SoCs.
> Current Exynos PCIe driver doesn't use the PHY framework.
> It's making a difficult to upstream the other Exynos variants because of
> different PHY registers.
>
> Move the codes relevant to PHY from Exnyos PCIe driver to PHY Exynos PCIe
> driver.
>
> Signed-off-by: Jaehoon Chung<jh80.chung@...sung.com>
> Acked-by: Krzysztof Kozlowski<krzk@...nel.org>
> Reviewed-by: Jingoo Han<jingoohan1@...il.com>
> Reviewed-by: Pankaj Dubey<pankaj.dubey@...sung.com>
> ---
> Changelog on V3:
> - Remove the dependency abot PCI_EXYNOS
> - Adds a depends on COMPILE_TEST
> - Use the readl_poll_timeout() instead of while()
> - Fixes const type
> - Adds MODULE_DESCRIPTION()/LICENCSE()/AUTHOR()
> - Changes commit message
>
> Changelog on V2:
> - Not include the codes relevant to pci-exynos.
> - Remove the getting child node.
>
>   drivers/phy/Kconfig           |   8 ++
>   drivers/phy/Makefile          |   1 +
>   drivers/phy/phy-exynos-pcie.c | 285 ++++++++++++++++++++++++++++++++++++++++++
>   3 files changed, 294 insertions(+)
>   create mode 100644 drivers/phy/phy-exynos-pcie.c
>
> diff --git a/drivers/phy/Kconfig b/drivers/phy/Kconfig
> index e8eb7f2..8659f38 100644
> --- a/drivers/phy/Kconfig
> +++ b/drivers/phy/Kconfig
> @@ -331,6 +331,14 @@ config PHY_EXYNOS5_USBDRD
>   	  This driver provides PHY interface for USB 3.0 DRD controller
>   	  present on Exynos5 SoC series.
>   
> +config PHY_EXYNOS_PCIE
> +	bool "Exynos PCIe PHY driver"
> +	depends on (ARCH_EXYNOS && OF) || COMPILE_TEST

this should be other way round if your driver runs only with OF enabled.
           depends on OF && (ARCH_EXYNOS || COMPILE_TEST)

> +	select GENERIC_PHY
> +	help
> +	  Enable PCIe PHY support for Exynos SoC series.
> +	  This driver provides PHY interface for Exynos PCIe controller.
> +
>   config PHY_PISTACHIO_USB
>   	tristate "IMG Pistachio USB2.0 PHY driver"
>   	depends on MACH_PISTACHIO
> diff --git a/drivers/phy/Makefile b/drivers/phy/Makefile
> index 65eb2f4..081aeb4 100644
> --- a/drivers/phy/Makefile
> +++ b/drivers/phy/Makefile
> @@ -37,6 +37,7 @@ phy-exynos-usb2-$(CONFIG_PHY_EXYNOS4X12_USB2)	+= phy-exynos4x12-usb2.o
>   phy-exynos-usb2-$(CONFIG_PHY_EXYNOS5250_USB2)	+= phy-exynos5250-usb2.o
>   phy-exynos-usb2-$(CONFIG_PHY_S5PV210_USB2)	+= phy-s5pv210-usb2.o
>   obj-$(CONFIG_PHY_EXYNOS5_USBDRD)	+= phy-exynos5-usbdrd.o
> +obj-$(CONFIG_PHY_EXYNOS_PCIE)	+= phy-exynos-pcie.o
>   obj-$(CONFIG_PHY_QCOM_APQ8064_SATA)	+= phy-qcom-apq8064-sata.o
>   obj-$(CONFIG_PHY_ROCKCHIP_USB) += phy-rockchip-usb.o
>   obj-$(CONFIG_PHY_ROCKCHIP_INNO_USB2)	+= phy-rockchip-inno-usb2.o
> diff --git a/drivers/phy/phy-exynos-pcie.c b/drivers/phy/phy-exynos-pcie.c
> new file mode 100644
> index 0000000..9ec1855
> --- /dev/null
> +++ b/drivers/phy/phy-exynos-pcie.c
> @@ -0,0 +1,285 @@
> +/*
> + * Samsung EXYNOS SoC series PCIe PHY driver
> + *
> + * Phy provider for PCIe controller on Exynos SoC series
> + *
> + * Copyright (C) 2016 Samsung Electronics Co., Ltd.

nit: copyright year.

> + * Jaehoon Chung<jh80.chung@...sung.com>
> + *
> + * This program is free software; you can redistribute it and/or modify
> + * it under the terms of the GNU General Public License version 2 as
> + * published by the Free Software Foundation.
> + */
> +
> +#include <linux/delay.h>
> +#include <linux/io.h>
> +#include <linux/iopoll.h>
> +#include <linux/mfd/syscon.h>
> +#include <linux/module.h>
> +#include <linux/of.h>
> +#include <linux/of_address.h>
> +#include <linux/of_platform.h>
> +#include <linux/platform_device.h>
> +#include <linux/phy/phy.h>
> +#include <linux/regmap.h>
> +
> +/* PCIe Purple registers */
> +#define PCIE_PHY_GLOBAL_RESET		0x000
> +#define PCIE_PHY_COMMON_RESET		0x004
> +#define PCIE_PHY_CMN_REG		0x008
> +#define PCIE_PHY_MAC_RESET		0x00c
> +#define PCIE_PHY_PLL_LOCKED		0x010
> +#define PCIE_PHY_TRSVREG_RESET		0x020
> +#define PCIE_PHY_TRSV_RESET		0x024
> +
> +/* PCIe PHY registers */
> +#define PCIE_PHY_IMPEDANCE		0x004
> +#define PCIE_PHY_PLL_DIV_0		0x008
> +#define PCIE_PHY_PLL_BIAS		0x00c
> +#define PCIE_PHY_DCC_FEEDBACK		0x014
> +#define PCIE_PHY_PLL_DIV_1		0x05c
> +#define PCIE_PHY_COMMON_POWER		0x064
> +#define PCIE_PHY_COMMON_PD_CMN		BIT(3)
> +#define PCIE_PHY_TRSV0_EMP_LVL		0x084
> +#define PCIE_PHY_TRSV0_DRV_LVL		0x088
> +#define PCIE_PHY_TRSV0_RXCDR		0x0ac
> +#define PCIE_PHY_TRSV0_POWER		0x0c4
> +#define PCIE_PHY_TRSV0_PD_TSV		BIT(7)
> +#define PCIE_PHY_TRSV0_LVCC		0x0dc
> +#define PCIE_PHY_TRSV1_EMP_LVL		0x144
> +#define PCIE_PHY_TRSV1_RXCDR		0x16c
> +#define PCIE_PHY_TRSV1_POWER		0x184
> +#define PCIE_PHY_TRSV1_PD_TSV		BIT(7)
> +#define PCIE_PHY_TRSV1_LVCC		0x19c
> +#define PCIE_PHY_TRSV2_EMP_LVL		0x204
> +#define PCIE_PHY_TRSV2_RXCDR		0x22c
> +#define PCIE_PHY_TRSV2_POWER		0x244
> +#define PCIE_PHY_TRSV2_PD_TSV		BIT(7)
> +#define PCIE_PHY_TRSV2_LVCC		0x25c
> +#define PCIE_PHY_TRSV3_EMP_LVL		0x2c4
> +#define PCIE_PHY_TRSV3_RXCDR		0x2ec
> +#define PCIE_PHY_TRSV3_POWER		0x304
> +#define PCIE_PHY_TRSV3_PD_TSV		BIT(7)
> +#define PCIE_PHY_TRSV3_LVCC		0x31c
> +
> +struct exynos_pcie_phy_data {
> +	const struct phy_ops	*ops;
> +};
> +
> +/* For Exynos pcie phy */
> +struct exynos_pcie_phy {
> +	const struct exynos_pcie_phy_data *drv_data;
> +	void __iomem *phy_base;
> +	void __iomem *blk_base; /* For exynos5440 */
> +};
> +
> +static void exynos_pcie_phy_writel(void __iomem *base, u32 val, u32 offset)
> +{
> +	writel(val, base + offset);
> +}
> +
> +static u32 exynos_pcie_phy_readl(void __iomem *base, u32 offset)
> +{
> +	return readl(base + offset);
> +}
> +
> +/* For Exynos5440 specific functions */
> +static int exynos5440_pcie_phy_init(struct phy *phy)
> +{
> +	struct exynos_pcie_phy *ep = phy_get_drvdata(phy);
> +
> +	/* DCC feedback control off */
> +	exynos_pcie_phy_writel(ep->phy_base, 0x29, PCIE_PHY_DCC_FEEDBACK);
> +
> +	/* set TX/RX impedance */
> +	exynos_pcie_phy_writel(ep->phy_base, 0xd5, PCIE_PHY_IMPEDANCE);
> +
> +	/* set 50Mhz PHY clock */
> +	exynos_pcie_phy_writel(ep->phy_base, 0x14, PCIE_PHY_PLL_DIV_0);
> +	exynos_pcie_phy_writel(ep->phy_base, 0x12, PCIE_PHY_PLL_DIV_1);
> +
> +	/* set TX Differential output for lane 0 */
> +	exynos_pcie_phy_writel(ep->phy_base, 0x7f, PCIE_PHY_TRSV0_DRV_LVL);
> +
> +	/* set TX Pre-emphasis Level Control for lane 0 to minimum */
> +	exynos_pcie_phy_writel(ep->phy_base, 0x0, PCIE_PHY_TRSV0_EMP_LVL);
> +
> +	/* set RX clock and data recovery bandwidth */
> +	exynos_pcie_phy_writel(ep->phy_base, 0xe7, PCIE_PHY_PLL_BIAS);
> +	exynos_pcie_phy_writel(ep->phy_base, 0x82, PCIE_PHY_TRSV0_RXCDR);
> +	exynos_pcie_phy_writel(ep->phy_base, 0x82, PCIE_PHY_TRSV1_RXCDR);
> +	exynos_pcie_phy_writel(ep->phy_base, 0x82, PCIE_PHY_TRSV2_RXCDR);
> +	exynos_pcie_phy_writel(ep->phy_base, 0x82, PCIE_PHY_TRSV3_RXCDR);
> +
> +	/* change TX Pre-emphasis Level Control for lanes */
> +	exynos_pcie_phy_writel(ep->phy_base, 0x39, PCIE_PHY_TRSV0_EMP_LVL);
> +	exynos_pcie_phy_writel(ep->phy_base, 0x39, PCIE_PHY_TRSV1_EMP_LVL);
> +	exynos_pcie_phy_writel(ep->phy_base, 0x39, PCIE_PHY_TRSV2_EMP_LVL);
> +	exynos_pcie_phy_writel(ep->phy_base, 0x39, PCIE_PHY_TRSV3_EMP_LVL);
> +
> +	/* set LVCC */
> +	exynos_pcie_phy_writel(ep->phy_base, 0x20, PCIE_PHY_TRSV0_LVCC);
> +	exynos_pcie_phy_writel(ep->phy_base, 0xa0, PCIE_PHY_TRSV1_LVCC);
> +	exynos_pcie_phy_writel(ep->phy_base, 0xa0, PCIE_PHY_TRSV2_LVCC);
> +	exynos_pcie_phy_writel(ep->phy_base, 0xa0, PCIE_PHY_TRSV3_LVCC);
> +
> +	/* pulse for common reset */
> +	exynos_pcie_phy_writel(ep->blk_base, 1, PCIE_PHY_COMMON_RESET);
> +	udelay(500);
> +	exynos_pcie_phy_writel(ep->blk_base, 0, PCIE_PHY_COMMON_RESET);
> +
> +	return 0;
> +}
> +
> +static int exynos5440_pcie_phy_power_on(struct phy *phy)
> +{
> +	struct exynos_pcie_phy *ep = phy_get_drvdata(phy);
> +	u32 val;
> +
> +	exynos_pcie_phy_writel(ep->blk_base, 0, PCIE_PHY_COMMON_RESET);
> +	exynos_pcie_phy_writel(ep->blk_base, 0, PCIE_PHY_CMN_REG);
> +	exynos_pcie_phy_writel(ep->blk_base, 0, PCIE_PHY_TRSVREG_RESET);
> +	exynos_pcie_phy_writel(ep->blk_base, 0, PCIE_PHY_TRSV_RESET);
> +
> +	val = exynos_pcie_phy_readl(ep->phy_base, PCIE_PHY_COMMON_POWER);
> +	val &= ~PCIE_PHY_COMMON_PD_CMN;
> +	exynos_pcie_phy_writel(ep->phy_base, val, PCIE_PHY_COMMON_POWER);
> +
> +	val = exynos_pcie_phy_readl(ep->phy_base, PCIE_PHY_TRSV0_POWER);
> +	val &= ~PCIE_PHY_TRSV0_PD_TSV;
> +	exynos_pcie_phy_writel(ep->phy_base, val, PCIE_PHY_TRSV0_POWER);
> +
> +	val = exynos_pcie_phy_readl(ep->phy_base, PCIE_PHY_TRSV1_POWER);
> +	val &= ~PCIE_PHY_TRSV1_PD_TSV;
> +	exynos_pcie_phy_writel(ep->phy_base, val, PCIE_PHY_TRSV1_POWER);
> +
> +	val = exynos_pcie_phy_readl(ep->phy_base, PCIE_PHY_TRSV2_POWER);
> +	val &= ~PCIE_PHY_TRSV2_PD_TSV;
> +	exynos_pcie_phy_writel(ep->phy_base, val, PCIE_PHY_TRSV2_POWER);
> +
> +	val = exynos_pcie_phy_readl(ep->phy_base, PCIE_PHY_TRSV3_POWER);
> +	val &= ~PCIE_PHY_TRSV3_PD_TSV;
> +	exynos_pcie_phy_writel(ep->phy_base, val, PCIE_PHY_TRSV3_POWER);
> +
> +	return 0;
> +}
> +
> +static int exynos5440_pcie_phy_power_off(struct phy *phy)
> +{
> +	struct exynos_pcie_phy *ep = phy_get_drvdata(phy);
> +	u32 val;
> +
> +	if (readl_poll_timeout(ep->phy_base + PCIE_PHY_PLL_LOCKED, val,
> +				(val != 0), 1, 500)) {
> +		dev_err(&phy->dev, "PLL Locked: 0x%x\n", val);
> +		return -ETIMEDOUT;
> +	}
> +
> +	val = exynos_pcie_phy_readl(ep->phy_base, PCIE_PHY_COMMON_POWER);
> +	val |= PCIE_PHY_COMMON_PD_CMN;
> +	exynos_pcie_phy_writel(ep->phy_base, val, PCIE_PHY_COMMON_POWER);
> +
> +	val = exynos_pcie_phy_readl(ep->phy_base, PCIE_PHY_TRSV0_POWER);
> +	val |= PCIE_PHY_TRSV0_PD_TSV;
> +	exynos_pcie_phy_writel(ep->phy_base, val, PCIE_PHY_TRSV0_POWER);
> +
> +	val = exynos_pcie_phy_readl(ep->phy_base, PCIE_PHY_TRSV1_POWER);
> +	val |= PCIE_PHY_TRSV1_PD_TSV;
> +	exynos_pcie_phy_writel(ep->phy_base, val, PCIE_PHY_TRSV1_POWER);
> +
> +	val = exynos_pcie_phy_readl(ep->phy_base, PCIE_PHY_TRSV2_POWER);
> +	val |= PCIE_PHY_TRSV2_PD_TSV;
> +	exynos_pcie_phy_writel(ep->phy_base, val, PCIE_PHY_TRSV2_POWER);
> +
> +	val = exynos_pcie_phy_readl(ep->phy_base, PCIE_PHY_TRSV3_POWER);
> +	val |= PCIE_PHY_TRSV3_PD_TSV;
> +	exynos_pcie_phy_writel(ep->phy_base, val, PCIE_PHY_TRSV3_POWER);
> +
> +	return 0;
> +}
> +
> +static int exynos5440_pcie_phy_reset(struct phy *phy)
> +{
> +	struct exynos_pcie_phy *ep = phy_get_drvdata(phy);
> +
> +	exynos_pcie_phy_writel(ep->blk_base, 0, PCIE_PHY_MAC_RESET);
> +	exynos_pcie_phy_writel(ep->blk_base, 1, PCIE_PHY_GLOBAL_RESET);
> +	exynos_pcie_phy_writel(ep->blk_base, 0, PCIE_PHY_GLOBAL_RESET);
> +
> +	return 0;
> +}
> +
> +static const struct phy_ops exynos5440_phy_ops = {
> +	.init		= exynos5440_pcie_phy_init,
> +	.power_on	= exynos5440_pcie_phy_power_on,
> +	.power_off	= exynos5440_pcie_phy_power_off,
> +	.reset		= exynos5440_pcie_phy_reset,
> +	.owner		= THIS_MODULE,
> +};
> +
> +static const struct exynos_pcie_phy_data exynos5440_pcie_phy_data = {
> +	.ops		= &exynos5440_phy_ops,
> +};
> +
> +static const struct of_device_id exynos_pcie_phy_match[] = {
> +	{
> +		.compatible = "samsung,exynos5440-pcie-phy",
> +		.data = &exynos5440_pcie_phy_data,
> +	},
> +	{},
> +};
> +MODULE_DEVICE_TABLE(of, exynos_pcie_phy_match);
> +
> +static int exynos_pcie_phy_probe(struct platform_device *pdev)
> +{
> +	struct device *dev = &pdev->dev;
> +	struct exynos_pcie_phy *exynos_phy;
> +	struct phy *generic_phy;
> +	struct phy_provider *phy_provider;
> +	struct resource *res;
> +	const struct exynos_pcie_phy_data *drv_data;
> +
> +	drv_data = of_device_get_match_data(dev);
> +	if (!drv_data)
> +		return -ENODEV;
> +
> +	exynos_phy = devm_kzalloc(dev, sizeof(*exynos_phy), GFP_KERNEL);
> +	if (!exynos_phy)
> +		return -ENOMEM;
> +
> +	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
> +	exynos_phy->phy_base = devm_ioremap_resource(dev, res);
> +	if (IS_ERR(exynos_phy->phy_base))
> +		return PTR_ERR(exynos_phy->phy_base);
> +
> +	res = platform_get_resource(pdev, IORESOURCE_MEM, 1);
> +	exynos_phy->blk_base = devm_ioremap_resource(dev, res);
> +	if (IS_ERR(exynos_phy->phy_base))
> +		return PTR_ERR(exynos_phy->phy_base);
> +
> +	exynos_phy->drv_data = drv_data;
> +
> +	generic_phy = devm_phy_create(dev, dev->of_node, drv_data->ops);
> +	if (IS_ERR(generic_phy)) {
> +		dev_err(dev, "failed to create PHY\n");
> +		return PTR_ERR(generic_phy);
> +	}
> +
> +	phy_set_drvdata(generic_phy, exynos_phy);
> +	phy_provider = devm_of_phy_provider_register(dev, of_phy_simple_xlate);
> +
> +	return PTR_ERR_OR_ZERO(phy_provider);
> +}
> +
> +static struct platform_driver exynos_pcie_phy_driver = {
> +	.probe	= exynos_pcie_phy_probe,
> +	.driver = {
> +		.of_match_table	= exynos_pcie_phy_match,
> +		.name		= "exynos_pcie_phy",
> +	}
> +};
> +module_platform_driver(exynos_pcie_phy_driver);
> +
> +MODULE_DESCRIPTION("Samsung S5P/EXYNOS SoC PCIe PHY driver");
> +MODULE_AUTHOR("Jaehoon Chung<jh80.chung@...sung.com>");
> +MODULE_LICENSE("GPL v2");

rest looks good to me.
Reviewed-by: Vivek Gautam <vivek.gautam@...eaurora.org>

-- 

The Qualcomm Innovation Center, Inc. is a member of Code Aurora Forum,
a Linux Foundation Collaborative Project

Powered by blists - more mailing lists