linux-kernel - [PATCH V2 0/6] tty: serial: lpuart: add imx7ulp support

lists.openwall.net		lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC
Open Source and information security mailing list archives

Hash Suite: Windows password security audit tool. GUI, reports in PDF.

[<prev] [next>] [thread-next>] [day] [month] [year] [list]

Message-ID: <1494834539-17523-1-git-send-email-aisheng.dong@nxp.com>
Date:   Mon, 15 May 2017 15:48:53 +0800
From:   Dong Aisheng <aisheng.dong@....com>
To:     <linux-serial@...r.kernel.org>
CC:     <linux-kernel@...r.kernel.org>,
        <linux-arm-kernel@...ts.infradead.org>,
        <gregkh@...uxfoundation.org>, <jslaby@...e.com>,
        <fugang.duan@....com>, <stefan@...er.ch>, <dongas86@...il.com>,
        <Mingkai.Hu@....com>, <yangbo.lu@....com>,
        Dong Aisheng <aisheng.dong@....com>
Subject: [PATCH V2 0/6] tty: serial: lpuart: add imx7ulp support

This patch series mainly intends to add imx7ulp support which is also
using FSL lpuart.

The lpuart in imx7ulp is basically the same as ls1021a. It's also
32 bit width register, but unlike ls1021a, it's little endian.
Besides that, imx7ulp lpuart has a minor different register layout
from ls1021a that it has four extra registers (verid, param, global,
pincfg) located at the beginning of register map, which are currently
not used by the driver and less to be used later.

Furthermore, this patch serial also add a new more accurate baud rate
calculation method as MX7ULP can't divide a suitable baud rate
with the default setting.

Currently the new baud rate calculation is only enabled on MX7ULP.
However, i guess the Layerscape may also be able to use it as there
seems to be no difference in baud rate setting register after checking
the Layerscape Reference Manual.

As i don't have Layerscape boards, i can't test it, so i only enable it
for MX7ULP by default to avoid a potential break.

I copied LayerScape guys in this series and hope they can help test later.
If it works on Layerscape as well, then they can switch to the new setting
too and totally remove the old stuff.

ChangeLog:
v1->v2:
 * Patch 2/4/5 chagned, other no changes.
   See individuals for details.

Dong Aisheng (6):
  tty: serial: lpuart: introduce lpuart_soc_data to represent SoC
    property
  tty: serial: lpuart: add little endian 32 bit register support
  dt-bindings: serial: fsl-lpuart: add i.MX7ULP support
  tty: serial: lpuart: add imx7ulp support
  tty: serial: lpuart: add earlycon support for imx7ulp
  tty: serial: lpuart: add a more accurate baud rate calculation method

 .../devicetree/bindings/serial/fsl-lpuart.txt      |   2 +
 drivers/tty/serial/fsl_lpuart.c                    | 147 ++++++++++++++++++---
 2 files changed, 134 insertions(+), 15 deletions(-)

-- 
2.7.4