| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-ID: <039e0091-12d5-e582-fb87-9805533eae54@roeck-us.net>
Date: Mon, 15 May 2017 06:18:51 -0700
From: Guenter Roeck <linux@...ck-us.net>
To: Chris Packham <chris.packham@...iedtelesis.co.nz>,
linux-hwmon@...r.kernel.org, jdelvare@...e.com
Cc: Jonathan Corbet <corbet@....net>, linux-doc@...r.kernel.org,
linux-kernel@...r.kernel.org
Subject: Re: [PATCH v4 2/3] hwmon: (adt7475) temperature smoothing
On 05/14/2017 06:30 PM, Chris Packham wrote:
> When enabled temperature smoothing allows ramping the fan speed over a
> configurable period of time instead of jumping to the new speed
> instantaneously.
>
> Signed-off-by: Chris Packham <chris.packham@...iedtelesis.co.nz>
Applied to -next.
> ---
> Changes in v2:
> - use a single tempN_smoothing attribute
> Changes in v3:
> - change enh_acou to enh_acoustics
> - simplify show_temp_st()
> Changes in v4:
> - removed dead code.
> - Make the order of the smoothing attributes match the other temperature
> attributes.
>
> Guenter,
>
> We'd previously discussed making the smoothing values set CONFIG6[SLOW] to
> expose the other set of potential values. I wasn't sure where you wanted to go
> on that one.
>
> Personally I was on the fence since the difference would only be noticeable for
> the higher values. If we do want to add support for the other values it could
> be done as a subsequent patch (or a v5 if you want it).
>
It can be added later if anyone cares.
Thanks,
Guenter
> Documentation/hwmon/adt7475 | 4 ++
> drivers/hwmon/adt7475.c | 91 +++++++++++++++++++++++++++++++++++++++++++++
> 2 files changed, 95 insertions(+)
>
> diff --git a/Documentation/hwmon/adt7475 b/Documentation/hwmon/adt7475
> index dc0b55794c47..09d73a10644c 100644
> --- a/Documentation/hwmon/adt7475
> +++ b/Documentation/hwmon/adt7475
> @@ -114,6 +114,10 @@ minimum (i.e. auto_point1_pwm). This behaviour can be configured using the
> pwm[1-*]_stall_disable sysfs attribute. A value of 0 means the fans will shut
> off. A value of 1 means the fans will run at auto_point1_pwm.
>
> +The responsiveness of the ADT747x to temperature changes can be configured.
> +This allows smoothing of the fan speed transition. To set the transition time
> +set the value in ms in the temp[1-*]_smoothing sysfs attribute.
> +
> Notes
> -----
>
> diff --git a/drivers/hwmon/adt7475.c b/drivers/hwmon/adt7475.c
> index 3eb8c5c2f8af..3056076fae27 100644
> --- a/drivers/hwmon/adt7475.c
> +++ b/drivers/hwmon/adt7475.c
> @@ -526,6 +526,88 @@ static ssize_t set_temp(struct device *dev, struct device_attribute *attr,
> return count;
> }
>
> +/* Assuming CONFIG6[SLOW] is 0 */
> +static const int ad7475_st_map[] = {
> + 37500, 18800, 12500, 7500, 4700, 3100, 1600, 800,
> +};
> +
> +static ssize_t show_temp_st(struct device *dev, struct device_attribute *attr,
> + char *buf)
> +{
> + struct sensor_device_attribute_2 *sattr = to_sensor_dev_attr_2(attr);
> + struct i2c_client *client = to_i2c_client(dev);
> + struct adt7475_data *data = i2c_get_clientdata(client);
> + long val;
> +
> + switch (sattr->index) {
> + case 0:
> + val = data->enh_acoustics[0] & 0xf;
> + break;
> + case 1:
> + val = (data->enh_acoustics[1] >> 4) & 0xf;
> + break;
> + case 2:
> + default:
> + val = data->enh_acoustics[1] & 0xf;
> + break;
> + }
> +
> + if (val & 0x8)
> + return sprintf(buf, "%d\n", ad7475_st_map[val & 0x7]);
> + else
> + return sprintf(buf, "0\n");
> +}
> +
> +static ssize_t set_temp_st(struct device *dev, struct device_attribute *attr,
> + const char *buf, size_t count)
> +{
> + struct sensor_device_attribute_2 *sattr = to_sensor_dev_attr_2(attr);
> + struct i2c_client *client = to_i2c_client(dev);
> + struct adt7475_data *data = i2c_get_clientdata(client);
> + unsigned char reg;
> + int shift, idx;
> + ulong val;
> +
> + if (kstrtoul(buf, 10, &val))
> + return -EINVAL;
> +
> + switch (sattr->index) {
> + case 0:
> + reg = REG_ENHANCE_ACOUSTICS1;
> + shift = 0;
> + idx = 0;
> + break;
> + case 1:
> + reg = REG_ENHANCE_ACOUSTICS2;
> + shift = 0;
> + idx = 1;
> + break;
> + case 2:
> + default:
> + reg = REG_ENHANCE_ACOUSTICS2;
> + shift = 4;
> + idx = 1;
> + break;
> + }
> +
> + if (val > 0) {
> + val = find_closest_descending(val, ad7475_st_map,
> + ARRAY_SIZE(ad7475_st_map));
> + val |= 0x8;
> + }
> +
> + mutex_lock(&data->lock);
> +
> + data->enh_acoustics[idx] &= ~(0xf << shift);
> + data->enh_acoustics[idx] |= (val << shift);
> +
> + i2c_smbus_write_byte_data(client, reg, data->enh_acoustics[idx]);
> +
> + mutex_unlock(&data->lock);
> +
> + return count;
> +}
> +
> /*
> * Table of autorange values - the user will write the value in millidegrees,
> * and we'll convert it
> @@ -1008,6 +1090,8 @@ static SENSOR_DEVICE_ATTR_2(temp1_crit, S_IRUGO | S_IWUSR, show_temp, set_temp,
> THERM, 0);
> static SENSOR_DEVICE_ATTR_2(temp1_crit_hyst, S_IRUGO | S_IWUSR, show_temp,
> set_temp, HYSTERSIS, 0);
> +static SENSOR_DEVICE_ATTR_2(temp1_smoothing, S_IRUGO | S_IWUSR, show_temp_st,
> + set_temp_st, 0, 0);
> static SENSOR_DEVICE_ATTR_2(temp2_input, S_IRUGO, show_temp, NULL, INPUT, 1);
> static SENSOR_DEVICE_ATTR_2(temp2_alarm, S_IRUGO, show_temp, NULL, ALARM, 1);
> static SENSOR_DEVICE_ATTR_2(temp2_max, S_IRUGO | S_IWUSR, show_temp, set_temp,
> @@ -1024,6 +1108,8 @@ static SENSOR_DEVICE_ATTR_2(temp2_crit, S_IRUGO | S_IWUSR, show_temp, set_temp,
> THERM, 1);
> static SENSOR_DEVICE_ATTR_2(temp2_crit_hyst, S_IRUGO | S_IWUSR, show_temp,
> set_temp, HYSTERSIS, 1);
> +static SENSOR_DEVICE_ATTR_2(temp2_smoothing, S_IRUGO | S_IWUSR, show_temp_st,
> + set_temp_st, 0, 1);
> static SENSOR_DEVICE_ATTR_2(temp3_input, S_IRUGO, show_temp, NULL, INPUT, 2);
> static SENSOR_DEVICE_ATTR_2(temp3_alarm, S_IRUGO, show_temp, NULL, ALARM, 2);
> static SENSOR_DEVICE_ATTR_2(temp3_fault, S_IRUGO, show_temp, NULL, FAULT, 2);
> @@ -1041,6 +1127,8 @@ static SENSOR_DEVICE_ATTR_2(temp3_crit, S_IRUGO | S_IWUSR, show_temp, set_temp,
> THERM, 2);
> static SENSOR_DEVICE_ATTR_2(temp3_crit_hyst, S_IRUGO | S_IWUSR, show_temp,
> set_temp, HYSTERSIS, 2);
> +static SENSOR_DEVICE_ATTR_2(temp3_smoothing, S_IRUGO | S_IWUSR, show_temp_st,
> + set_temp_st, 0, 2);
> static SENSOR_DEVICE_ATTR_2(fan1_input, S_IRUGO, show_tach, NULL, INPUT, 0);
> static SENSOR_DEVICE_ATTR_2(fan1_min, S_IRUGO | S_IWUSR, show_tach, set_tach,
> MIN, 0);
> @@ -1125,6 +1213,7 @@ static struct attribute *adt7475_attrs[] = {
> &sensor_dev_attr_temp1_auto_point2_temp.dev_attr.attr,
> &sensor_dev_attr_temp1_crit.dev_attr.attr,
> &sensor_dev_attr_temp1_crit_hyst.dev_attr.attr,
> + &sensor_dev_attr_temp1_smoothing.dev_attr.attr,
> &sensor_dev_attr_temp2_input.dev_attr.attr,
> &sensor_dev_attr_temp2_alarm.dev_attr.attr,
> &sensor_dev_attr_temp2_max.dev_attr.attr,
> @@ -1134,6 +1223,7 @@ static struct attribute *adt7475_attrs[] = {
> &sensor_dev_attr_temp2_auto_point2_temp.dev_attr.attr,
> &sensor_dev_attr_temp2_crit.dev_attr.attr,
> &sensor_dev_attr_temp2_crit_hyst.dev_attr.attr,
> + &sensor_dev_attr_temp2_smoothing.dev_attr.attr,
> &sensor_dev_attr_temp3_input.dev_attr.attr,
> &sensor_dev_attr_temp3_fault.dev_attr.attr,
> &sensor_dev_attr_temp3_alarm.dev_attr.attr,
> @@ -1144,6 +1234,7 @@ static struct attribute *adt7475_attrs[] = {
> &sensor_dev_attr_temp3_auto_point2_temp.dev_attr.attr,
> &sensor_dev_attr_temp3_crit.dev_attr.attr,
> &sensor_dev_attr_temp3_crit_hyst.dev_attr.attr,
> + &sensor_dev_attr_temp3_smoothing.dev_attr.attr,
> &sensor_dev_attr_fan1_input.dev_attr.attr,
> &sensor_dev_attr_fan1_min.dev_attr.attr,
> &sensor_dev_attr_fan1_alarm.dev_attr.attr,
>
Powered by blists - more mailing lists