| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-ID: <1495197739-17446-3-git-send-email-j-keerthy@ti.com>
Date: Fri, 19 May 2017 18:12:18 +0530
From: Keerthy <j-keerthy@...com>
To: <broonie@...nel.org>, <lee.jones@...aro.org>, <robh+dt@...nel.org>
CC: <j-keerthy@...com>, <t-kristo@...com>, <tony@...mide.com>,
<mark.rutland@....com>, <linux-omap@...r.kernel.org>,
<linux-kernel@...r.kernel.org>, <devicetree@...r.kernel.org>
Subject: [PATCH 2/3] regulator: lp87565: Add support for lp87565 PMIC regulators
The regulators set consists of 4 BUCKs. The output
voltages are configurable and are meant to supply power to the
main processor and other components. The ramp delay is configurable
for all BUCKs. The BUCKs can be configured in single phase or
multiphase modes.
Signed-off-by: Keerthy <j-keerthy@...com>
---
drivers/regulator/Kconfig | 8 ++
drivers/regulator/Makefile | 1 +
drivers/regulator/lp87565-regulator.c | 244 ++++++++++++++++++++++++++++++++++
3 files changed, 253 insertions(+)
create mode 100644 drivers/regulator/lp87565-regulator.c
diff --git a/drivers/regulator/Kconfig b/drivers/regulator/Kconfig
index 48db87d..7c34ff8 100644
--- a/drivers/regulator/Kconfig
+++ b/drivers/regulator/Kconfig
@@ -365,6 +365,14 @@ config REGULATOR_LP8755
chip contains six step-down DC/DC converters which can support
9 mode multiphase configuration.
+config REGULATOR_LP87565
+ tristate "TI LP87565 Power regulators"
+ depends on MFD_TI_LP87565 && OF
+ help
+ This driver supports LP87565 voltage regulator chips. LP87565
+ provides four step-down converters. It supports software based
+ voltage control for different voltage domains
+
config REGULATOR_LP8788
tristate "TI LP8788 Power Regulators"
depends on MFD_LP8788
diff --git a/drivers/regulator/Makefile b/drivers/regulator/Makefile
index dc3503f..fee6b8c 100644
--- a/drivers/regulator/Makefile
+++ b/drivers/regulator/Makefile
@@ -46,6 +46,7 @@ obj-$(CONFIG_REGULATOR_LP3971) += lp3971.o
obj-$(CONFIG_REGULATOR_LP3972) += lp3972.o
obj-$(CONFIG_REGULATOR_LP872X) += lp872x.o
obj-$(CONFIG_REGULATOR_LP873X) += lp873x-regulator.o
+obj-$(CONFIG_REGULATOR_LP87565) += lp87565-regulator.o
obj-$(CONFIG_REGULATOR_LP8788) += lp8788-buck.o
obj-$(CONFIG_REGULATOR_LP8788) += lp8788-ldo.o
obj-$(CONFIG_REGULATOR_LP8755) += lp8755.o
diff --git a/drivers/regulator/lp87565-regulator.c b/drivers/regulator/lp87565-regulator.c
new file mode 100644
index 0000000..5849cf3
--- /dev/null
+++ b/drivers/regulator/lp87565-regulator.c
@@ -0,0 +1,244 @@
+/*
+ * Regulator driver for LP87565 PMIC
+ *
+ * Copyright (C) 2017 Texas Instruments Incorporated - http://www.ti.com/
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ * This program is distributed "as is" WITHOUT ANY WARRANTY of any
+ * kind, whether expressed or implied; without even the implied warranty
+ * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License version 2 for more details.
+ */
+
+#include <linux/module.h>
+#include <linux/platform_device.h>
+#include <linux/regmap.h>
+
+#include <linux/mfd/lp87565.h>
+
+#define LP87565_REGULATOR(_name, _id, _of, _ops, _n, _vr, _vm, _er, _em, \
+ _delay, _lr, _cr) \
+ [_id] = { \
+ .desc = { \
+ .name = _name, \
+ .supply_name = _of "-in", \
+ .id = _id, \
+ .of_match = of_match_ptr(_of), \
+ .regulators_node = of_match_ptr("regulators"),\
+ .ops = &_ops, \
+ .n_voltages = _n, \
+ .type = REGULATOR_VOLTAGE, \
+ .owner = THIS_MODULE, \
+ .vsel_reg = _vr, \
+ .vsel_mask = _vm, \
+ .enable_reg = _er, \
+ .enable_mask = _em, \
+ .ramp_delay = _delay, \
+ .linear_ranges = _lr, \
+ .n_linear_ranges = ARRAY_SIZE(_lr), \
+ }, \
+ .ctrl2_reg = _cr, \
+ }
+
+#define LP87565_Q1_MIN_IDX LP87565_BUCK_10
+
+struct lp87565_regulator {
+ struct regulator_desc desc;
+ unsigned int ctrl2_reg;
+};
+
+static const struct lp87565_regulator regulators[];
+
+static const struct regulator_linear_range buck0_1_2_3_ranges[] = {
+ REGULATOR_LINEAR_RANGE(500000, 0x0, 0x17, 10000),
+ REGULATOR_LINEAR_RANGE(735000, 0x18, 0x9d, 5000),
+ REGULATOR_LINEAR_RANGE(1420000, 0x9e, 0xff, 20000),
+};
+
+static unsigned int lp87565_buck_ramp_delay[] = {
+ 30000, 15000, 10000, 7500, 3800, 1900, 940, 470
+};
+
+/* LP87565 BUCK current limit */
+static const unsigned int lp87565_buck_uA[] = {
+ 1500000, 2000000, 2500000, 3000000, 3500000, 4000000, 4500000, 5000000,
+};
+
+static int lp87565_buck_set_ramp_delay(struct regulator_dev *rdev,
+ int ramp_delay)
+{
+ int id = rdev_get_id(rdev);
+ struct lp87565 *lp87565 = rdev_get_drvdata(rdev);
+ unsigned int reg;
+ int ret;
+
+ if (ramp_delay <= 470)
+ reg = 7;
+ else if (ramp_delay <= 940)
+ reg = 6;
+ else if (ramp_delay <= 1900)
+ reg = 5;
+ else if (ramp_delay <= 3800)
+ reg = 4;
+ else if (ramp_delay <= 7500)
+ reg = 3;
+ else if (ramp_delay <= 10000)
+ reg = 2;
+ else if (ramp_delay <= 15000)
+ reg = 1;
+ else
+ reg = 0;
+
+ ret = regmap_update_bits(lp87565->regmap, regulators[id].ctrl2_reg,
+ LP87565_BUCK_CTRL_2_SLEW_RATE,
+ reg << __ffs(LP87565_BUCK_CTRL_2_SLEW_RATE));
+ if (ret) {
+ dev_err(lp87565->dev, "SLEW RATE write failed: %d\n", ret);
+ return ret;
+ }
+
+ rdev->constraints->ramp_delay = lp87565_buck_ramp_delay[reg];
+
+ return 0;
+}
+
+static int lp87565_buck_set_current_limit(struct regulator_dev *rdev,
+ int min_uA, int max_uA)
+{
+ int id = rdev_get_id(rdev);
+ struct lp87565 *lp87565 = rdev_get_drvdata(rdev);
+ int i;
+
+ for (i = ARRAY_SIZE(lp87565_buck_uA) - 1; i >= 0; i--) {
+ if (lp87565_buck_uA[i] >= min_uA &&
+ lp87565_buck_uA[i] <= max_uA)
+ return regmap_update_bits(lp87565->regmap,
+ regulators[id].ctrl2_reg,
+ LP87565_BUCK_CTRL_2_ILIM,
+ i << __ffs(LP87565_BUCK_CTRL_2_ILIM));
+ }
+
+ return -EINVAL;
+}
+
+static int lp87565_buck_get_current_limit(struct regulator_dev *rdev)
+{
+ int id = rdev_get_id(rdev);
+ struct lp87565 *lp87565 = rdev_get_drvdata(rdev);
+ int ret;
+ unsigned int val;
+
+ ret = regmap_read(lp87565->regmap, regulators[id].ctrl2_reg, &val);
+ if (ret)
+ return ret;
+
+ val = (val & LP87565_BUCK_CTRL_2_ILIM) >>
+ __ffs(LP87565_BUCK_CTRL_2_ILIM);
+
+ return (val < ARRAY_SIZE(lp87565_buck_uA)) ?
+ lp87565_buck_uA[val] : -EINVAL;
+}
+
+/* Operations permitted on BUCK0, BUCK1 */
+static struct regulator_ops lp87565_buck_ops = {
+ .is_enabled = regulator_is_enabled_regmap,
+ .enable = regulator_enable_regmap,
+ .disable = regulator_disable_regmap,
+ .get_voltage_sel = regulator_get_voltage_sel_regmap,
+ .set_voltage_sel = regulator_set_voltage_sel_regmap,
+ .list_voltage = regulator_list_voltage_linear_range,
+ .map_voltage = regulator_map_voltage_linear_range,
+ .set_voltage_time_sel = regulator_set_voltage_time_sel,
+ .set_ramp_delay = lp87565_buck_set_ramp_delay,
+ .set_current_limit = lp87565_buck_set_current_limit,
+ .get_current_limit = lp87565_buck_get_current_limit,
+};
+
+static const struct lp87565_regulator regulators[] = {
+ LP87565_REGULATOR("BUCK0", LP87565_BUCK_0, "buck0", lp87565_buck_ops,
+ 256, LP87565_REG_BUCK0_VOUT, LP87565_BUCK_VSET,
+ LP87565_REG_BUCK0_CTRL_1,
+ LP87565_BUCK_CTRL_1_EN, 3800,
+ buck0_1_2_3_ranges, LP87565_REG_BUCK0_CTRL_2),
+ LP87565_REGULATOR("BUCK1", LP87565_BUCK_1, "buck1", lp87565_buck_ops,
+ 256, LP87565_REG_BUCK1_VOUT, LP87565_BUCK_VSET,
+ LP87565_REG_BUCK1_CTRL_1,
+ LP87565_BUCK_CTRL_1_EN, 3800,
+ buck0_1_2_3_ranges, LP87565_REG_BUCK1_CTRL_2),
+ LP87565_REGULATOR("BUCK2", LP87565_BUCK_2, "buck2", lp87565_buck_ops,
+ 256, LP87565_REG_BUCK2_VOUT, LP87565_BUCK_VSET,
+ LP87565_REG_BUCK2_CTRL_1,
+ LP87565_BUCK_CTRL_1_EN, 3800,
+ buck0_1_2_3_ranges, LP87565_REG_BUCK2_CTRL_2),
+ LP87565_REGULATOR("BUCK3", LP87565_BUCK_3, "buck3", lp87565_buck_ops,
+ 256, LP87565_REG_BUCK3_VOUT, LP87565_BUCK_VSET,
+ LP87565_REG_BUCK3_CTRL_1,
+ LP87565_BUCK_CTRL_1_EN, 3800,
+ buck0_1_2_3_ranges, LP87565_REG_BUCK3_CTRL_2),
+ LP87565_REGULATOR("BUCK10", LP87565_BUCK_10, "buck10", lp87565_buck_ops,
+ 256, LP87565_REG_BUCK0_VOUT, LP87565_BUCK_VSET,
+ LP87565_REG_BUCK0_CTRL_1,
+ LP87565_BUCK_CTRL_1_EN, 3800,
+ buck0_1_2_3_ranges, LP87565_REG_BUCK0_CTRL_2),
+ LP87565_REGULATOR("BUCK23", LP87565_BUCK_23, "buck23", lp87565_buck_ops,
+ 256, LP87565_REG_BUCK2_VOUT, LP87565_BUCK_VSET,
+ LP87565_REG_BUCK2_CTRL_1,
+ LP87565_BUCK_CTRL_1_EN, 3800,
+ buck0_1_2_3_ranges, LP87565_REG_BUCK2_CTRL_2),
+};
+
+static int lp87565_regulator_probe(struct platform_device *pdev)
+{
+ struct lp87565 *lp87565 = dev_get_drvdata(pdev->dev.parent);
+ struct regulator_config config = { };
+ struct regulator_dev *rdev;
+ int i, min_idx = LP87565_BUCK_1, max_idx = LP87565_BUCK_3;
+
+ platform_set_drvdata(pdev, lp87565);
+
+ config.dev = &pdev->dev;
+ config.dev->of_node = lp87565->dev->of_node;
+ config.driver_data = lp87565;
+ config.regmap = lp87565->regmap;
+
+ if (lp87565->dev_type == LP87565_DEVICE_TYPE_LP87565_Q1) {
+ min_idx = LP87565_BUCK_10;
+ max_idx = LP87565_BUCK_23;
+ }
+
+ for (i = min_idx; i <= max_idx; i++) {
+ rdev = devm_regulator_register(&pdev->dev, ®ulators[i].desc,
+ &config);
+ if (IS_ERR(rdev)) {
+ dev_err(lp87565->dev, "failed to register %s regulator\n",
+ pdev->name);
+ return PTR_ERR(rdev);
+ }
+ }
+
+ return 0;
+}
+
+static const struct platform_device_id lp87565_regulator_id_table[] = {
+ { "lp87565-regulator", },
+ { "lp87565-q1-regulator", },
+ { /* sentinel */ }
+};
+MODULE_DEVICE_TABLE(platform, lp87565_regulator_id_table);
+
+static struct platform_driver lp87565_regulator_driver = {
+ .driver = {
+ .name = "lp87565-pmic",
+ },
+ .probe = lp87565_regulator_probe,
+ .id_table = lp87565_regulator_id_table,
+};
+module_platform_driver(lp87565_regulator_driver);
+
+MODULE_AUTHOR("J Keerthy <j-keerthy@...com>");
+MODULE_DESCRIPTION("LP87565 voltage regulator driver");
+MODULE_ALIAS("platform:lp87565-pmic");
+MODULE_LICENSE("GPL v2");
--
1.9.1
Powered by blists - more mailing lists