[<prev] [next>] [<thread-prev] [thread-next>] [day] [month] [year] [list]
Message-Id: <1495458705-11692-4-git-send-email-geert+renesas@glider.be>
Date: Mon, 22 May 2017 15:11:42 +0200
From: Geert Uytterhoeven <geert+renesas@...der.be>
To: Mark Brown <broonie@...nel.org>
Cc: Rob Herring <robh+dt@...nel.org>,
Mark Rutland <mark.rutland@....com>,
Magnus Damm <magnus.damm@...il.com>,
Wolfram Sang <wsa+renesas@...g-engineering.com>,
Hiromitsu Yamasaki <hiromitsu.yamasaki.ym@...esas.com>,
Jiada Wang <jiada_wang@...tor.com>,
Matt Porter <mporter@...sulko.com>, linux-spi@...r.kernel.org,
devicetree@...r.kernel.org, linux-renesas-soc@...r.kernel.org,
linux-kernel@...r.kernel.org
Subject: [PATCH v5 3/6] spi: Document SPI slave controller support
Signed-off-by: Geert Uytterhoeven <geert+renesas@...der.be>
---
v3, v4, v5:
- No changes,
v2:
- New.
---
Documentation/spi/spi-summary | 27 ++++++++++++++++++++-------
1 file changed, 20 insertions(+), 7 deletions(-)
diff --git a/Documentation/spi/spi-summary b/Documentation/spi/spi-summary
index d1824b399b2d1d79..1721c1b570c32466 100644
--- a/Documentation/spi/spi-summary
+++ b/Documentation/spi/spi-summary
@@ -62,8 +62,8 @@ chips described as using "three wire" signaling: SCK, data, nCSx.
(That data line is sometimes called MOMI or SISO.)
Microcontrollers often support both master and slave sides of the SPI
-protocol. This document (and Linux) currently only supports the master
-side of SPI interactions.
+protocol. This document (and Linux) supports both the master and slave
+sides of SPI interactions.
Who uses it? On what kinds of systems?
@@ -154,9 +154,8 @@ control audio interfaces, present touchscreen sensors as input interfaces,
or monitor temperature and voltage levels during industrial processing.
And those might all be sharing the same controller driver.
-A "struct spi_device" encapsulates the master-side interface between
-those two types of driver. At this writing, Linux has no slave side
-programming interface.
+A "struct spi_device" encapsulates the controller-side interface between
+those two types of drivers.
There is a minimal core of SPI programming interfaces, focussing on
using the driver model to connect controller and protocol drivers using
@@ -177,10 +176,24 @@ shows up in sysfs in several locations:
/sys/bus/spi/drivers/D ... driver for one or more spi*.* devices
/sys/class/spi_master/spiB ... symlink (or actual device node) to
- a logical node which could hold class related state for the
- controller managing bus "B". All spiB.* devices share one
+ a logical node which could hold class related state for the SPI
+ master controller managing bus "B". All spiB.* devices share one
physical SPI bus segment, with SCLK, MOSI, and MISO.
+ /sys/devices/.../CTLR/slave ... virtual file for (un)registering the
+ slave device for an SPI slave controller.
+ Writing the driver name of an SPI slave handler to this file
+ registers the slave device; writing "(null)" unregisters the slave
+ device.
+ Reading from this file shows the name of the slave device ("(null)"
+ if not registered).
+
+ /sys/class/spi_slave/spiB ... symlink (or actual device node) to
+ a logical node which could hold class related state for the SPI
+ slave controller on bus "B". When registered, a single spiB.*
+ device is present here, possible sharing the physical SPI bus
+ segment with other SPI slave devices.
+
Note that the actual location of the controller's class state depends
on whether you enabled CONFIG_SYSFS_DEPRECATED or not. At this time,
the only class-specific state is the bus number ("B" in "spiB"), so
--
2.7.4
Powered by blists - more mailing lists