linux-kernel - Re: [RESEND: PATCH v4 2/4] remoteproc: qcom: refactor mss fw image loading sequence

lists.openwall.net		lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC
Open Source and information security mailing list archives

Hash Suite for Android: free password hash cracker in your pocket

[<prev] [next>] [<thread-prev] [thread-next>] [day] [month] [year] [list]

Message-ID: <20170525190317.GD12920@tuxbook>
Date:   Thu, 25 May 2017 12:03:17 -0700
From:   Bjorn Andersson <bjorn.andersson@...aro.org>
To:     "Dwivedi, Avaneesh Kumar (avani)" <akdwived@...eaurora.org>
Cc:     Sricharan R <sricharan@...eaurora.org>, sboyd@...eaurora.org,
        agross@...eaurora.org, linux-arm-msm@...r.kernel.org,
        linux-kernel@...r.kernel.org, linux-remoteproc@...r.kernel.org
Subject: Re: [RESEND: PATCH v4 2/4] remoteproc: qcom: refactor mss fw image
 loading sequence

On Mon 22 May 06:26 PDT 2017, Dwivedi, Avaneesh Kumar (avani) wrote:
> On 5/22/2017 4:07 PM, Sricharan R wrote:
> > Hi,
> > 
> > On 5/22/2017 3:03 PM, Dwivedi, Avaneesh Kumar (avani) wrote:
> > > 
> > > On 5/20/2017 8:25 AM, Sricharan R wrote:
> > > > Hi Bjorn/Avaneesh,
> > > > 
> > > > On 5/16/2017 11:32 PM, Avaneesh Kumar Dwivedi wrote:
[..]
> > > > > -
> > > > > -        size = readl(qproc->rmb_base + RMB_PMI_CODE_LENGTH_REG);
> > > > > -        if (!size) {
> > > > > -            boot_addr = relocate ? qproc->mpss_phys : min_addr;
> > > > > -            writel(boot_addr, qproc->rmb_base + RMB_PMI_CODE_START_REG);
> > > > > -            writel(RMB_CMD_LOAD_READY, qproc->rmb_base + RMB_MBA_COMMAND_REG);
> > > > > -        }
> > > > > -
> > > > >            size += phdr->p_memsz;
> > > > > -        writel(size, qproc->rmb_base + RMB_PMI_CODE_LENGTH_REG);
> > > > >        }
> > > > So while moving this down, can we use qcom_mdt_load instead for
> > > > the mpss image loading part above ?
> > > qcom_mdt_load() can not be used to load segments for mpss, as MPSS
> > > blobs are self authenticated.  while qcom_mdt_load() is used in
> > > cases where authentication of loaded blobs is done by trustzone.
> > > for that qcom_mdt_load() does extra steps to send pas_id to
> > > trustzone and mem_setup() etc.
> > Right, so my intention of asking this was if the code which does the
> > calculation and loads the segments in qcom_mdt_load can somehow be
> > abstracted out, so that future self authenticating rproc (even mpss
> > in this case) can use them to load mdt ?
> As i understand, you want to replace the piece of code which does
> parse mdt and load individual firmware blobs in a separate routine.
> So that it can be called by any one without again doing parsing and
> loading for self authentication.?  Till now only MPSS does rely on
> self authentication, all other subsystems use qcom_mdt_load().  I
> think this is reason why the qcom_mdt_load() equivalent routine has
> not been used.  Bjorn may further add in this.

I have not been able to come up with a clean way to provide a useful
mdt-loader abstraction that works for the SCM PILs, the
self-authenticated PILs and the non-PIL SCM users.

Further more with the upcoming ramdump support we will need to extract
segment information from the mdt header, so we will have to revisit this
topic.


Regardless, I would prefer that we follow up with such refactoring after
getting this series sorted out.

> > 
> > > > > +    /* Transfer ownership of modem region with modem fw */
> > > > > +    boot_addr = relocate ? qproc->mpss_phys : min_addr;
> > > > > +    writel(boot_addr, qproc->rmb_base + RMB_PMI_CODE_START_REG);
> > > > > +    writel(RMB_CMD_LOAD_READY, qproc->rmb_base + RMB_MBA_COMMAND_REG);
> > > > > +    writel(size, qproc->rmb_base + RMB_PMI_CODE_LENGTH_REG);
> > > > For ipq8074 [1], wcnss core has an Q6V5 version of the ip for
> > > > which the initialization/boot sequence is pretty much the same
> > > > as that has been added for msm8996 in this series. So wanted to
> > > > understand if its better to use this remoteproc itself by
> > > > keeping the Q6 and mpss parts separately (or) add a new
> > > > remoteproc ?
> > > Bjorn can better answer this query, but i believe this remoteproc
> > > can be extended to load mpss part by adding private initialization
> > > for the IP.
> > ya, the mpss part can be separated out, so that this can be a Q6 +
> > MPSS (or) Q6 + WCNSS remoteproc. Was asking this to get the right
> > way for adding the Q6 + WCNSS remoteproc, as the Q6 part is same
> > what you have added for msm8996.
> Again, i believe yes but leave Bjorn to make final comment.

It definitely sounds like there's room for reuse here, how much of the
initialization and authentication sequences are common between the two?

Regards,
Bjorn