Message-ID: <1496150860-25919-1-git-send-email-j-keerthy@ti.com>
Date:   Tue, 30 May 2017 18:57:40 +0530
From:   Keerthy <j-keerthy@...com>
To:     <broonie@...nel.org>, <lee.jones@...aro.org>, <robh+dt@...nel.org>
CC:     <j-keerthy@...com>, <t-kristo@...com>, <tony@...mide.com>,
        <mark.rutland@....com>, <linux-omap@...r.kernel.org>,
        <linux-kernel@...r.kernel.org>, <devicetree@...r.kernel.org>,
        <afd@...com>
Subject: [PATCH v3] mfd: lp87565: Add lp87565 PMIC support

The LP87565 chip is a power management IC for Portable Navigation Systems
and Tablet Computing devices. It contains the following components:

        - Configurable Bucks(Single and multi-phase).
        - Configurable General Purpose Output Signals (GPO).

The LP87565-Q1 variant device uses two 2-phase outputs configuration,
Buck0 is master for Buck0/1 output and Buck2 is master for Buck2/3
output.

Signed-off-by: Keerthy <j-keerthy@...com>
---

The other patches are already pulled by Mark. Hence posting
the remaining patch.

Changes in v3:

  * Fixed License to GPL v2.
  * Fixed an indentation issue.

Changes in v2:

  * Fixed a bunch of whitespace errors.
  * Changed the License to short form.
  * Added the generic compatible lp87565
  * Removed i2c_device_id table.
  * Introduced probe_new function in place of probe.

 Documentation/devicetree/bindings/mfd/lp87565.txt |  45 ++++
 drivers/mfd/Kconfig                               |  14 ++
 drivers/mfd/Makefile                              |   1 +
 drivers/mfd/lp87565.c                             |  92 ++++++++
 include/linux/mfd/lp87565.h                       | 270 ++++++++++++++++++++++
 5 files changed, 422 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/mfd/lp87565.txt
 create mode 100644 drivers/mfd/lp87565.c
 create mode 100644 include/linux/mfd/lp87565.h

diff --git a/Documentation/devicetree/bindings/mfd/lp87565.txt b/Documentation/devicetree/bindings/mfd/lp87565.txt
new file mode 100644
index 0000000..f63d568
--- /dev/null
+++ b/Documentation/devicetree/bindings/mfd/lp87565.txt
@@ -0,0 +1,45 @@
+TI LP87565 PMIC MFD driver
+
+Required properties:
+  - compatible:	"ti,lp87565", "ti,lp87565-q1"
+  - reg:		I2C slave address.
+  - gpio-controller:	Marks the device node as a GPIO Controller.
+  - #gpio-cells:	Should be two.  The first cell is the pin number and
+			the second cell is used to specify flags.
+			See ../gpio/gpio.txt for more information.
+  - xxx-in-supply:	Phandle to parent supply node of each regulator
+			populated under regulators node. xxx should match
+			the supply_name populated in driver.
+  - regulators:	List of child nodes that specify the regulator
+			initialization data.
+Example:
+
+lp87565_pmic: lp87565@60 {
+	compatible = "ti,lp87565-q1";
+	reg = <0x60>;
+	gpio-controller;
+	#gpio-cells = <2>;
+
+	buck10-in-supply = <&vsys_3v3>;
+	buck23-in-supply = <&vsys_3v3>;
+
+	regulators: regulators {
+		buck10_reg: buck10 {
+			/* VDD_MPU */
+			regulator-name = "buck10";
+			regulator-min-microvolt = <850000>;
+			regulator-max-microvolt = <1250000>;
+			regulator-always-on;
+			regulator-boot-on;
+		};
+
+		buck23_reg: buck23 {
+			/* VDD_GPU */
+			regulator-name = "buck23";
+			regulator-min-microvolt = <850000>;
+			regulator-max-microvolt = <1250000>;
+			regulator-boot-on;
+			regulator-always-on;
+		};
+	};
+};
diff --git a/drivers/mfd/Kconfig b/drivers/mfd/Kconfig
index 3eb5c93..e0008c7 100644
--- a/drivers/mfd/Kconfig
+++ b/drivers/mfd/Kconfig
@@ -1325,6 +1325,20 @@ config MFD_TI_LP873X
 	  This driver can also be built as a module. If so, the module
 	  will be called lp873x.
 
+config MFD_TI_LP87565
+	tristate "TI LP87565 Power Management IC"
+	depends on I2C && OF
+	select MFD_CORE
+	select REGMAP_I2C
+	help
+	  If you say yes here then you get support for the LP87565 series of
+	  Power Management Integrated Circuits (PMIC).
+	  These include voltage regulators, thermal protection, configurable
+	  General Purpose Outputs (GPO) that are used in portable devices.
+
+	  This driver can also be built as a module. If so, the module
+	  will be called lp87565.
+
 config MFD_TPS65218
 	tristate "TI TPS65218 Power Management chips"
 	depends on I2C
diff --git a/drivers/mfd/Makefile b/drivers/mfd/Makefile
index c16bf1e..7edbe1b 100644
--- a/drivers/mfd/Makefile
+++ b/drivers/mfd/Makefile
@@ -25,6 +25,7 @@ obj-$(CONFIG_HTC_PASIC3)	+= htc-pasic3.o
 obj-$(CONFIG_HTC_I2CPLD)	+= htc-i2cpld.o
 
 obj-$(CONFIG_MFD_TI_LP873X)	+= lp873x.o
+obj-$(CONFIG_MFD_TI_LP87565)	+= lp87565.o
 
 obj-$(CONFIG_MFD_DAVINCI_VOICECODEC)	+= davinci_voicecodec.o
 obj-$(CONFIG_MFD_DM355EVM_MSP)	+= dm355evm_msp.o
diff --git a/drivers/mfd/lp87565.c b/drivers/mfd/lp87565.c
new file mode 100644
index 0000000..70eae40
--- /dev/null
+++ b/drivers/mfd/lp87565.c
@@ -0,0 +1,92 @@
+/*
+ * Copyright (C) 2017 Texas Instruments Incorporated - http://www.ti.com/
+ *
+ * Author: Keerthy <j-keerthy@...com>
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation version 2.
+ */
+
+#include <linux/interrupt.h>
+#include <linux/mfd/core.h>
+#include <linux/module.h>
+#include <linux/of_device.h>
+#include <linux/regmap.h>
+
+#include <linux/mfd/lp87565.h>
+
+static const struct regmap_config lp87565_regmap_config = {
+	.reg_bits = 8,
+	.val_bits = 8,
+	.max_register = LP87565_REG_MAX,
+};
+
+static const struct mfd_cell lp87565_cells[] = {
+	{ .name = "lp87565-q1-regulator", },
+	{ .name = "lp87565-q1-gpio", },
+};
+
+static const struct of_device_id of_lp87565_match_table[] = {
+	{ .compatible = "ti,lp87565", },
+	{
+		.compatible = "ti,lp87565-q1",
+		.data = (void *)LP87565_DEVICE_TYPE_LP87565_Q1,
+	},
+	{}
+};
+MODULE_DEVICE_TABLE(of, of_lp87565_match_table);
+
+static int lp87565_probe(struct i2c_client *client)
+{
+	struct lp87565 *lp87565;
+	const struct of_device_id *of_id;
+	int ret;
+	unsigned int otpid;
+
+	lp87565 = devm_kzalloc(&client->dev, sizeof(*lp87565), GFP_KERNEL);
+	if (!lp87565)
+		return -ENOMEM;
+
+	lp87565->dev = &client->dev;
+
+	lp87565->regmap = devm_regmap_init_i2c(client, &lp87565_regmap_config);
+	if (IS_ERR(lp87565->regmap)) {
+		ret = PTR_ERR(lp87565->regmap);
+		dev_err(lp87565->dev,
+			"Failed to initialize register map: %d\n", ret);
+		return ret;
+	}
+
+	ret = regmap_read(lp87565->regmap, LP87565_REG_OTP_REV, &otpid);
+	if (ret) {
+		dev_err(lp87565->dev, "Failed to read OTP ID\n");
+		return ret;
+	}
+
+	lp87565->rev = otpid & LP87565_OTP_REV_OTP_ID;
+
+	of_id = of_match_device(of_lp87565_match_table, &client->dev);
+	if (of_id)
+		lp87565->dev_type = (enum lp87565_device_type)of_id->data;
+
+	i2c_set_clientdata(client, lp87565);
+
+	ret = mfd_add_devices(lp87565->dev, PLATFORM_DEVID_AUTO, lp87565_cells,
+			      ARRAY_SIZE(lp87565_cells), NULL, 0, NULL);
+
+	return ret;
+}
+
+static struct i2c_driver lp87565_driver = {
+	.driver	= {
+		.name	= "lp87565",
+		.of_match_table = of_lp87565_match_table,
+	},
+	.probe_new = lp87565_probe,
+};
+module_i2c_driver(lp87565_driver);
+
+MODULE_AUTHOR("J Keerthy <j-keerthy@...com>");
+MODULE_DESCRIPTION("lp87565 chip family Multi-Function Device driver");
+MODULE_LICENSE("GPL v2");
diff --git a/include/linux/mfd/lp87565.h b/include/linux/mfd/lp87565.h
new file mode 100644
index 0000000..d0c91ba
--- /dev/null
+++ b/include/linux/mfd/lp87565.h
@@ -0,0 +1,270 @@
+/*
+ * Functions to access LP87565 power management chip.
+ *
+ * Copyright (C) 2017 Texas Instruments Incorporated - http://www.ti.com/
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation version 2.
+ */
+
+#ifndef __LINUX_MFD_LP87565_H
+#define __LINUX_MFD_LP87565_H
+
+#include <linux/i2c.h>
+#include <linux/regulator/driver.h>
+#include <linux/regulator/machine.h>
+
+enum lp87565_device_type {
+	LP87565_DEVICE_TYPE_UNKNOWN	= 0,
+	LP87565_DEVICE_TYPE_LP87565_Q1,
+};
+
+/* All register addresses */
+#define LP87565_REG_DEV_REV		0X00
+#define LP87565_REG_OTP_REV		0X01
+#define LP87565_REG_BUCK0_CTRL_1		0X02
+#define LP87565_REG_BUCK0_CTRL_2		0X03
+
+#define LP87565_REG_BUCK1_CTRL_1		0X04
+#define LP87565_REG_BUCK1_CTRL_2		0X05
+
+#define LP87565_REG_BUCK2_CTRL_1		0X06
+#define LP87565_REG_BUCK2_CTRL_2		0X07
+
+#define LP87565_REG_BUCK3_CTRL_1		0X08
+#define LP87565_REG_BUCK3_CTRL_2		0X09
+
+#define LP87565_REG_BUCK0_VOUT			0X0A
+#define LP87565_REG_BUCK0_FLOOR_VOUT		0X0B
+
+#define LP87565_REG_BUCK1_VOUT			0X0C
+#define LP87565_REG_BUCK1_FLOOR_VOUT		0X0D
+
+#define LP87565_REG_BUCK2_VOUT			0X0E
+#define LP87565_REG_BUCK2_FLOOR_VOUT		0X0F
+
+#define LP87565_REG_BUCK3_VOUT			0X10
+#define LP87565_REG_BUCK3_FLOOR_VOUT		0X11
+
+#define LP87565_REG_BUCK0_DELAY			0X12
+#define LP87565_REG_BUCK1_DELAY			0X13
+
+#define LP87565_REG_BUCK2_DELAY			0X14
+#define LP87565_REG_BUCK3_DELAY			0X15
+
+#define LP87565_REG_GPO2_DELAY			0X16
+#define LP87565_REG_GPO3_DELAY			0X17
+#define LP87565_REG_RESET			0X18
+#define LP87565_REG_CONFIG			0X19
+
+#define LP87565_REG_INT_TOP_1			0X1A
+#define LP87565_REG_INT_TOP_2			0X1B
+
+#define LP87565_REG_INT_BUCK_0_1		0X1C
+#define LP87565_REG_INT_BUCK_2_3		0X1D
+#define LP87565_REG_TOP_STAT			0X1E
+#define LP87565_REG_BUCK_0_1_STAT		0X1F
+#define LP87565_REG_BUCK_2_3_STAT		0x20
+
+#define LP87565_REG_TOP_MASK_1			0x21
+#define LP87565_REG_TOP_MASK_2			0x22
+
+#define LP87565_REG_BUCK_0_1_MASK		0x23
+#define LP87565_REG_BUCK_2_3_MASK		0x24
+#define LP87565_REG_SEL_I_LOAD			0x25
+
+#define LP87565_REG_I_LOAD_2			0x26
+#define LP87565_REG_I_LOAD_1			0x27
+
+#define LP87565_REG_PGOOD_CTRL1			0x28
+#define LP87565_REG_PGOOD_CTRL2			0x29
+#define LP87565_REG_PGOOD_FLT			0x2A
+#define LP87565_REG_PLL_CTRL			0x2B
+#define LP87565_REG_PIN_FUNCTION		0x2C
+#define LP87565_REG_GPIO_CONFIG			0x2D
+#define LP87565_REG_GPIO_IN			0x2E
+#define LP87565_REG_GPIO_OUT			0x2F
+
+#define LP87565_REG_MAX			LP87565_REG_GPIO_OUT
+
+/* Register field definitions */
+#define LP87565_DEV_REV_DEV_ID			0xC0
+#define LP87565_DEV_REV_ALL_LAYER		0x30
+#define LP87565_DEV_REV_METAL_LAYER		0x0F
+
+#define LP87565_OTP_REV_OTP_ID			0xFF
+
+#define LP87565_BUCK_CTRL_1_EN			BIT(7)
+#define LP87565_BUCK_CTRL_1_EN_PIN_CTRL		BIT(6)
+#define LP87565_BUCK_CTRL_1_PIN_SELECT_EN	0x30
+
+#define LP87565_BUCK_CTRL_1_ROOF_FLOOR_EN	BIT(3)
+#define LP87565_BUCK_CTRL_1_RDIS_EN		BIT(2)
+#define LP87565_BUCK_CTRL_1_FPWM		BIT(1)
+/* Bit0 is reserved for BUCK1 and BUCK3 and valid only for BUCK0 and BUCK2 */
+#define LP87565_BUCK_CTRL_1_FPWM_MP_0_2		BIT(0)
+
+#define LP87565_BUCK_CTRL_2_ILIM		0x38
+#define LP87565_BUCK_CTRL_2_SLEW_RATE		0x07
+
+#define LP87565_BUCK_VSET			0xFF
+#define LP87565_BUCK_FLOOR_VSET			0xFF
+
+#define LP87565_BUCK_SHUTDOWN_DELAY		0xF0
+#define LP87565_BUCK_STARTUP_DELAY		0x0F
+
+#define LP87565_GPIO_SHUTDOWN_DELAY		0xF0
+#define LP87565_GPIO_STARTUP_DELAY		0x0F
+
+#define LP87565_RESET_SW_RESET			BIT(0)
+
+#define LP87565_CONFIG_DOUBLE_DELAY		BIT(7)
+#define LP87565_CONFIG_CLKIN_PD			BIT(6)
+#define LP87565_CONFIG_EN4_PD			BIT(5)
+#define LP87565_CONFIG_EN3_PD			BIT(4)
+#define LP87565_CONFIG_TDIE_WARN_LEVEL		BIT(3)
+#define LP87565_CONFIG_EN2_PD			BIT(2)
+#define LP87565_CONFIG_EN1_PD			BIT(1)
+
+#define LP87565_INT_GPIO			BIT(7)
+#define LP87565_INT_BUCK23			BIT(6)
+#define LP87565_INT_BUCK01			BIT(5)
+#define LP87565_NO_SYNC_CLK			BIT(4)
+#define LP87565_TDIE_SD				BIT(3)
+#define LP87565_TDIE_WARN			BIT(2)
+#define LP87565_INT_OVP				BIT(1)
+#define LP87565_I_LOAD_READY			BIT(0)
+
+#define LP87565_INT_TOP2_RESET_REG		BIT(0)
+
+#define LP87565_BUCK1_PG_INT			BIT(6)
+#define LP87565_BUCK1_SC_INT			BIT(5)
+#define LP87565_BUCK1_ILIM_INT			BIT(4)
+#define LP87565_BUCK0_PG_INT			BIT(2)
+#define LP87565_BUCK0_SC_INT			BIT(1)
+#define LP87565_BUCK0_ILIM_INT			BIT(0)
+
+#define LP87565_BUCK3_PG_INT			BIT(6)
+#define LP87565_BUCK3_SC_INT			BIT(5)
+#define LP87565_BUCK3_ILIM_INT			BIT(4)
+#define LP87565_BUCK2_PG_INT			BIT(2)
+#define LP87565_BUCK2_SC_INT			BIT(1)
+#define LP87565_BUCK2_ILIM_INT			BIT(0)
+
+#define LP87565_SYNC_CLK_STAT			BIT(4)
+#define LP87565_TDIE_SD_STAT			BIT(3)
+#define LP87565_TDIE_WARN_STAT			BIT(2)
+#define LP87565_OVP_STAT			BIT(1)
+
+#define LP87565_BUCK1_STAT			BIT(7)
+#define LP87565_BUCK1_PG_STAT			BIT(6)
+#define LP87565_BUCK1_ILIM_STAT			BIT(4)
+#define LP87565_BUCK0_STAT			BIT(3)
+#define LP87565_BUCK0_PG_STAT			BIT(2)
+#define LP87565_BUCK0_ILIM_STAT			BIT(0)
+
+#define LP87565_BUCK3_STAT			BIT(7)
+#define LP87565_BUCK3_PG_STAT			BIT(6)
+#define LP87565_BUCK3_ILIM_STAT			BIT(4)
+#define LP87565_BUCK2_STAT			BIT(3)
+#define LP87565_BUCK2_PG_STAT			BIT(2)
+#define LP87565_BUCK2_ILIM_STAT			BIT(0)
+
+#define LPL87565_GPIO_MASK			BIT(7)
+#define LPL87565_SYNC_CLK_MASK			BIT(4)
+#define LPL87565_TDIE_WARN_MASK			BIT(2)
+#define LPL87565_I_LOAD_READY_MASK		BIT(0)
+
+#define LPL87565_RESET_REG_MASK			BIT(0)
+
+#define LPL87565_BUCK1_PG_MASK			BIT(6)
+#define LPL87565_BUCK1_ILIM_MASK		BIT(4)
+#define LPL87565_BUCK0_PG_MASK			BIT(2)
+#define LPL87565_BUCK0_ILIM_MASK		BIT(0)
+
+#define LPL87565_BUCK3_PG_MASK			BIT(6)
+#define LPL87565_BUCK3_ILIM_MASK		BIT(4)
+#define LPL87565_BUCK2_PG_MASK			BIT(2)
+#define LPL87565_BUCK2_ILIM_MASK		BIT(0)
+
+#define LP87565_LOAD_CURRENT_BUCK_SELECT	0x3
+
+#define LP87565_I_LOAD2_BUCK_LOAD_CURRENT	0x3
+#define LP87565_I_LOAD1_BUCK_LOAD_CURRENT	0xFF
+
+#define LP87565_PG3_SEL				0xC0
+#define LP87565_PG2_SEL				0x30
+#define LP87565_PG1_SEL				0x0C
+#define LP87565_PG0_SEL				0x03
+
+#define LP87565_HALF_DAY			BIT(7)
+#define LP87565_EN_PG0_NINT			BIT(6)
+#define LP87565_PGOOD_SET_DELAY			BIT(5)
+#define LP87565_EN_PGFLT_STAT			BIT(4)
+#define LP87565_PGOOD_WINDOW			BIT(2)
+#define LP87565_PGOOD_OD			BIT(1)
+#define LP87565_PGOOD_POL			BIT(0)
+
+#define LP87565_PG3_FLT				BIT(3)
+#define LP87565_PG2_FLT				BIT(2)
+#define LP87565_PG1_FLT				BIT(1)
+#define LP87565_PG0_FLT				BIT(0)
+
+#define LP87565_PLL_MODE			0xC0
+#define LP87565_EXT_CLK_FREQ			0x1F
+
+#define LP87565_EN_SPREAD_SPEC			BIT(7)
+#define LP87565_EN_PIN_CTRL_GPIO3		BIT(6)
+#define LP87565_EN_PIN_SELECT_GPIO3		BIT(5)
+#define LP87565_EN_PIN_CTRL_GPIO2		BIT(4)
+#define LP87565_EN_PIN_SELECT_GPIO2		BIT(3)
+#define LP87565_GPIO3_SEL			BIT(2)
+#define LP87565_GPIO2_SEL			BIT(1)
+#define LP87565_GPIO1_SEL			BIT(0)
+
+#define LP87565_GOIO3_OD			BIT(6)
+#define LP87565_GOIO2_OD			BIT(5)
+#define LP87565_GOIO1_OD			BIT(4)
+#define LP87565_GOIO3_DIR			BIT(2)
+#define LP87565_GOIO2_DIR			BIT(1)
+#define LP87565_GOIO1_DIR			BIT(0)
+
+#define LP87565_GOIO3_IN			BIT(2)
+#define LP87565_GOIO2_IN			BIT(1)
+#define LP87565_GOIO1_IN			BIT(0)
+
+#define LP87565_GOIO3_OUT			BIT(2)
+#define LP87565_GOIO2_OUT			BIT(1)
+#define LP87565_GOIO1_OUT			BIT(0)
+
+/* Number of step-down converters available */
+#define LP87565_NUM_BUCK		6
+
+enum LP87565_regulator_id {
+	/* BUCK's */
+	LP87565_BUCK_0,
+	LP87565_BUCK_1,
+	LP87565_BUCK_2,
+	LP87565_BUCK_3,
+	LP87565_BUCK_10,
+	LP87565_BUCK_23,
+};
+
+/**
+ * struct LP87565 - state holder for the LP87565 driver
+ * @dev: struct device pointer for MFD device
+ * @rev: revision of the LP87565
+ * @dev_type: The device type for example lp87565-q1
+ * @lock: lock guarding the data structure
+ * @regmap: register map of the LP87565 PMIC
+ *
+ * Device data may be used to access the LP87565 chip
+ */
+struct lp87565 {
+	struct device *dev;
+	u8 rev;
+	u8 dev_type;
+	struct regmap *regmap;
+};
+#endif /* __LINUX_MFD_LP87565_H */
-- 
1.9.1

Powered by blists - more mailing lists