| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-Id: <1496905959-29202-4-git-send-email-chenjh@rock-chips.com>
Date: Thu, 8 Jun 2017 15:12:30 +0800
From: Jianhong Chen <chenjh@...k-chips.com>
To: gnurou@...il.com, linus.walleij@...aro.org,
dmitry.torokhov@...il.com
Cc: linux-rockchip@...ts.infradead.org, linux-kernel@...r.kernel.org,
huangtao@...k-chips.com, tony.xie@...k-chips.com,
zhangqing@...k-chips.com, devicetree@...r.kernel.org,
w.egorov@...tec.de, lgirdwood@...il.com, broonie@...nel.org,
robh+dt@...nel.org, mark.rutland@....com,
linux-gpio@...r.kernel.org, linux-input@...r.kernel.org
Subject: [PATCH v6 03/12] regulator: rk808: Add regulator driver for RK805
From: Elaine Zhang <zhangqing@...k-chips.com>
Add support for the rk805 regulator. The regulator module consists
of 4 DCDCs, 3 LDOs.
The output voltages are configurable and are meant to supply power
to the main processor and other components.
Signed-off-by: Elaine Zhang <zhangqing@...k-chips.com>
---
drivers/regulator/Kconfig | 4 +-
drivers/regulator/rk808-regulator.c | 130 ++++++++++++++++++++++++++++++++++++
2 files changed, 132 insertions(+), 2 deletions(-)
diff --git a/drivers/regulator/Kconfig b/drivers/regulator/Kconfig
index be06eb2..285e280 100644
--- a/drivers/regulator/Kconfig
+++ b/drivers/regulator/Kconfig
@@ -650,11 +650,11 @@ config REGULATOR_RC5T583
outputs which can be controlled by i2c communication.
config REGULATOR_RK808
- tristate "Rockchip RK808/RK818 Power regulators"
+ tristate "Rockchip RK805/RK808/RK818 Power regulators"
depends on MFD_RK808
help
Select this option to enable the power regulator of ROCKCHIP
- PMIC RK808 and RK818.
+ PMIC RK805,RK808 and RK818.
This driver supports the control of different power rails of device
through regulator interface. The device supports multiple DCDC/LDO
outputs which can be controlled by i2c communication.
diff --git a/drivers/regulator/rk808-regulator.c b/drivers/regulator/rk808-regulator.c
index fb44d52..128c81e 100644
--- a/drivers/regulator/rk808-regulator.c
+++ b/drivers/regulator/rk808-regulator.c
@@ -65,6 +65,27 @@
/* max steps for increase voltage of Buck1/2, equal 100mv*/
#define MAX_STEPS_ONE_TIME 8
+#define RK805_DESC(_id, _match, _supply, _min, _max, _step, _vreg, \
+ _vmask, _ereg, _emask, _etime) \
+ [_id] = { \
+ .name = (_match), \
+ .supply_name = (_supply), \
+ .of_match = of_match_ptr(_match), \
+ .regulators_node = of_match_ptr("regulators"), \
+ .type = REGULATOR_VOLTAGE, \
+ .id = (_id), \
+ .n_voltages = (((_max) - (_min)) / (_step) + 1), \
+ .owner = THIS_MODULE, \
+ .min_uV = (_min) * 1000, \
+ .uV_step = (_step) * 1000, \
+ .vsel_reg = (_vreg), \
+ .vsel_mask = (_vmask), \
+ .enable_reg = (_ereg), \
+ .enable_mask = (_emask), \
+ .enable_time = (_etime), \
+ .ops = &rk805_reg_ops, \
+ }
+
#define RK8XX_DESC(_id, _match, _supply, _min, _max, _step, _vreg, \
_vmask, _ereg, _emask, _etime) \
[_id] = { \
@@ -298,6 +319,28 @@ static int rk808_set_suspend_voltage_range(struct regulator_dev *rdev, int uv)
sel);
}
+static int rk805_set_suspend_enable(struct regulator_dev *rdev)
+{
+ unsigned int reg;
+
+ reg = rdev->desc->enable_reg + RK808_SLP_SET_OFF_REG_OFFSET;
+
+ return regmap_update_bits(rdev->regmap, reg,
+ rdev->desc->enable_mask,
+ rdev->desc->enable_mask);
+}
+
+static int rk805_set_suspend_disable(struct regulator_dev *rdev)
+{
+ unsigned int reg;
+
+ reg = rdev->desc->enable_reg + RK808_SLP_SET_OFF_REG_OFFSET;
+
+ return regmap_update_bits(rdev->regmap, reg,
+ rdev->desc->enable_mask,
+ 0);
+}
+
static int rk808_set_suspend_enable(struct regulator_dev *rdev)
{
unsigned int reg;
@@ -320,6 +363,27 @@ static int rk808_set_suspend_disable(struct regulator_dev *rdev)
rdev->desc->enable_mask);
}
+static struct regulator_ops rk805_reg_ops = {
+ .list_voltage = regulator_list_voltage_linear,
+ .map_voltage = regulator_map_voltage_linear,
+ .get_voltage_sel = regulator_get_voltage_sel_regmap,
+ .set_voltage_sel = regulator_set_voltage_sel_regmap,
+ .enable = regulator_enable_regmap,
+ .disable = regulator_disable_regmap,
+ .is_enabled = regulator_is_enabled_regmap,
+ .set_suspend_voltage = rk808_set_suspend_voltage,
+ .set_suspend_enable = rk805_set_suspend_enable,
+ .set_suspend_disable = rk805_set_suspend_disable,
+};
+
+static struct regulator_ops rk805_switch_ops = {
+ .enable = regulator_enable_regmap,
+ .disable = regulator_disable_regmap,
+ .is_enabled = regulator_is_enabled_regmap,
+ .set_suspend_enable = rk805_set_suspend_enable,
+ .set_suspend_disable = rk805_set_suspend_disable,
+};
+
static struct regulator_ops rk808_buck1_2_ops = {
.list_voltage = regulator_list_voltage_linear,
.map_voltage = regulator_map_voltage_linear,
@@ -369,6 +433,68 @@ static int rk808_set_suspend_disable(struct regulator_dev *rdev)
.set_suspend_disable = rk808_set_suspend_disable,
};
+static const struct regulator_desc rk805_reg[] = {
+ {
+ .name = "DCDC_REG1",
+ .supply_name = "vcc1",
+ .of_match = of_match_ptr("DCDC_REG1"),
+ .regulators_node = of_match_ptr("regulators"),
+ .id = RK805_ID_DCDC1,
+ .ops = &rk805_reg_ops,
+ .type = REGULATOR_VOLTAGE,
+ .min_uV = 712500,
+ .uV_step = 12500,
+ .n_voltages = 64,
+ .vsel_reg = RK805_BUCK1_ON_VSEL_REG,
+ .vsel_mask = RK818_BUCK_VSEL_MASK,
+ .enable_reg = RK805_DCDC_EN_REG,
+ .enable_mask = BIT(0),
+ .owner = THIS_MODULE,
+ }, {
+ .name = "DCDC_REG2",
+ .supply_name = "vcc2",
+ .of_match = of_match_ptr("DCDC_REG2"),
+ .regulators_node = of_match_ptr("regulators"),
+ .id = RK805_ID_DCDC2,
+ .ops = &rk805_reg_ops,
+ .type = REGULATOR_VOLTAGE,
+ .min_uV = 712500,
+ .uV_step = 12500,
+ .n_voltages = 64,
+ .vsel_reg = RK805_BUCK2_ON_VSEL_REG,
+ .vsel_mask = RK818_BUCK_VSEL_MASK,
+ .enable_reg = RK805_DCDC_EN_REG,
+ .enable_mask = BIT(1),
+ .owner = THIS_MODULE,
+ }, {
+ .name = "DCDC_REG3",
+ .supply_name = "vcc3",
+ .of_match = of_match_ptr("DCDC_REG3"),
+ .regulators_node = of_match_ptr("regulators"),
+ .id = RK805_ID_DCDC3,
+ .ops = &rk805_switch_ops,
+ .type = REGULATOR_VOLTAGE,
+ .n_voltages = 1,
+ .enable_reg = RK805_DCDC_EN_REG,
+ .enable_mask = BIT(2),
+ .owner = THIS_MODULE,
+ },
+
+ RK805_DESC(RK805_ID_DCDC4, "DCDC_REG4", "vcc4", 800, 3400, 100,
+ RK805_BUCK4_ON_VSEL_REG, RK818_BUCK4_VSEL_MASK,
+ RK805_DCDC_EN_REG, BIT(3), 0),
+
+ RK805_DESC(RK805_ID_LDO1, "LDO_REG1", "vcc5", 800, 3400, 100,
+ RK805_LDO1_ON_VSEL_REG, RK818_LDO_VSEL_MASK, RK805_LDO_EN_REG,
+ BIT(0), 400),
+ RK805_DESC(RK805_ID_LDO2, "LDO_REG2", "vcc5", 800, 3400, 100,
+ RK805_LDO2_ON_VSEL_REG, RK818_LDO_VSEL_MASK, RK805_LDO_EN_REG,
+ BIT(1), 400),
+ RK805_DESC(RK805_ID_LDO3, "LDO_REG3", "vcc6", 800, 3400, 100,
+ RK805_LDO3_ON_VSEL_REG, RK818_LDO_VSEL_MASK, RK805_LDO_EN_REG,
+ BIT(2), 400),
+};
+
static const struct regulator_desc rk808_reg[] = {
{
.name = "DCDC_REG1",
@@ -625,6 +751,10 @@ static int rk808_regulator_probe(struct platform_device *pdev)
platform_set_drvdata(pdev, pdata);
switch (rk808->variant) {
+ case RK805_ID:
+ regulators = rk805_reg;
+ nregulators = RK805_NUM_REGULATORS;
+ break;
case RK808_ID:
regulators = rk808_reg;
nregulators = RK808_NUM_REGULATORS;
--
1.9.1
Powered by blists - more mailing lists